Yükselteç IC'leri
Ürünler (1.100+)
MS32051 - 4-Ch 25Gb/s CDR+TIA Array Receiver | Macom/Microsemi
The MS32051 is a 4-channel optical array receiver with integrated Clock and Data Recovery (CDR) and Transimpedance Amplifier (TIA), designed for 24Gb/s to 28Gb/s QSFP28-style optical modules. Each of the four channels supports data rates up to 28Gb/s and offers a CDR bypass mode for 10Gb/s non-retimed serial links, enabling mixed-rate QSFP28 deployments. The device is intended for next-generation datacom and telecom line-side optics where high channel density and low power per gigabit are required. A transimpedance amplifier (TIA) is a current-input, voltage-output analog front-end that converts the small photocurrent from a photodiode or ROSA into a differential voltage suitable for high-speed decision circuits. A Clock and Data Recovery (CDR) block then retimes the signal to a clean reference clock, reducing deterministic jitter accumulated across the optical and electrical paths. Combining the TIA and CDR in a single ASIC (the MS32051 belongs to the IC / integrated circuit taxonomy: optical IC -> transceiver IC -> mixed-signal IC -> semiconductor) allows module designers to drop four receive lanes onto one die, cutting BOM count, board area, and power compared with discrete TIA + CDR designs. Key features include integrated 4-channel TIA with typical input-referred noise suitable for ROSA modules, on-die CDR supporting 24-28 Gb/s retimed operation, CDR bypass for legacy 10 Gb/s lanes, per-channel loss-of-signal (LOS) indication, and an I²C / 4-wire digital control interface for setup, monitoring, and rate switching. Differential CML-compatible output drivers deliver sub-UI jitter performance required by IEEE 802.3bm / 100GBASE-SR4 links. Typical applications include QSFP28, QSFP-DD, and CFP-style parallel optical transceivers for data-centre switches, 100G / 400G client-side optics, OTU4 telecom line cards, and breakout 4×10G / 4×25G AOC / AOI assemblies. Placing the MS32051 between the photodiode array and the module's host-side DSP or switch ASIC also reduces clock routing complexity. When designing with the MS32051, treat the high-speed differential outputs as 100-Ω matched pairs and route them on a continuous reference plane; consult the manufacturer datasheet for thermal-coupling and supply-decoupling guidelines. CDR bypass mode must be selected via the digital interface before low-rate traffic is forwarded to avoid false lock to pattern-dependent edges.
NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi
The onsemi NCS199A1RSQT2G is a zero-drift, voltage-output current-shunt monitor (current sense amplifier) with a fixed gain of 50 V/V, supplied in a 6-pin SC-88 / SC-70-6 / SOT-363 surface-mount package. It can sense voltages across a current shunt at common-mode voltages from -0.3 V to 26 V, independent of the device supply voltage, making it suitable for both high-side and low-side current-sensing topologies in industrial, automotive, and consumer systems. The device operates from a single supply of 2.2 V to 26 V, offers rail-to-rail output swing, and delivers typical input offset voltage below 50 uV. A current sense amplifier (CSA) is a type of instrumentation amplifier that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. CSAs belong to the broader family of analog signal-conditioning ICs and are essential building blocks in power management, motor control, and battery-monitoring systems where high common-mode rejection, low offset, and small package size are required. Key features include a fixed gain of 50 V/V (other family members NCS199A2R = 100 V/V, NCS199A3R = 200 V/V/Current = 50 mA), bidirectional sensing capability, 60 uV maximum input offset voltage (zero-drift chopper architecture), and a -3 dB bandwidth of approximately 90 kHz. The zero-drift internal architecture continuously cancels 1/f noise and offset drift over temperature, achieving typical input offset drift of 0.5 uV/C. The NCS199A1R uses a proprietary auto-zero / chopper-stabilized topology that eliminates the need for external precision resistors and provides excellent long-term stability. Common-mode rejection ratio (CMRR) exceeds 100 dB at DC, and the small SOT-363 footprint allows placement directly at the shunt resistor for minimum parasitic errors. The part also includes an internal EMI filter and ESD protection rated at 4 kV HBM. Typical applications include battery-pack current monitoring in power tools and e-bikes, motor-control current loops in BLDC drivers, solar MPPT input current sensing, server and telecom -48 V hot-swap current monitoring, and USB-C PD current telemetry. In all cases the wide -0.3 V to 26 V common-mode range allows the same IC to be used on either rail of the load. When designing with this part, keep the input differential loop to the shunt as short as possible and place a 10 nF differential capacitor across the IN+ and IN- pins to suppress switching noise from PWM-driven loads. Ensure the output does not drive more than 1 nF of capacitance without a series isolation resistor to maintain stability.
NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi
The onsemi NCV2202SN2T1G is a sub-one-volt, low-power, single-channel CMOS comparator in a 5-pin SOT-23 (TSOP) package, qualified to the AEC-Q100 automotive standard. It operates over a supply voltage range of 0.85V to 6.0V, consumes only 10 uA of quiescent current, and provides an open-drain output capable of rail-to-rail input and rail-to-rail output swing. The NCV2202 prefix indicates AEC-Q100 / PPAP-capable automotive grade screening, while the non-automotive NCS2202 family member shares the same die and pinout. What is a low-voltage CMOS comparator? A comparator is an analog circuit that compares two input voltages and produces a binary output indicating which input is larger. Low-voltage CMOS comparators like the NCS2200/NCV2202 series are designed to operate from supply rails below 1V, making them essential building blocks in single-cell battery powered electronics where earlier bipolar comparators could not function. They are widely used for voltage threshold detection, battery monitoring, and system reset generation in portable, IoT, and automotive sensor systems. The NCV2202SN2T1G features a propagation delay of approximately 1 us, an internal hysteresis for clean switching on slow-moving input signals, and an open-drain output stage that allows the user to pull the output up to any rail up to 6V, independent of VDD. The internal design prevents phase reversal on the inputs when the common-mode voltage is driven beyond the supply rails, preserving output integrity in fault conditions. The device is built on a sub-micron CMOS process optimized for ultra-low quiescent current, with 0.3 uA consumption when the enable pin is held low (output tri-state). Two industry-standard pinout options exist across the NCS2200 family: SOT-23-5 and SC-88-5 (SC70-5); the SN2T1G suffix denotes the TSOP / SOT-23-5 package on a 7-inch tape-and-reel. Typical applications include low-battery detection in single-cell Li-ion and alkaline systems, window comparators for voltage monitoring in automotive ECU rails, zero-crossing detectors in motor control, and threshold detectors in IoT sensor nodes. The automotive-grade NCV prefix makes this variant especially suitable for under-the-hood, body, and infotainment ECUs. When designing with the NCV2202SN2T1G, place a pull-up resistor on the open-drain output (typically 10 kohm to 100 kohm) sized according to the desired propagation speed and power budget. Decouple VDD with a 100 nF ceramic capacitor located within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.
NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi
The onsemi NCV2250SN2T3G is a single high-speed, low-voltage, rail-to-rail comparator with push-pull output, packaged in a 5-pin TSOP. It delivers a typical propagation delay of 50 ns with a 100 mV input overdrive, making it well suited for fast threshold detection in space-constrained designs. The part operates from a single 1.8 V to 5.5 V range, and the input common-mode range extends 200 mV beyond both supply rails, allowing direct sensing near ground or VCC. The push-pull output stage eliminates the external pull-up resistor required by open-drain alternatives and swings to within millivolts of both rails. A comparator is an analog active device that compares two input voltages and drives its output logic a discrete single (high or low) based on which input is more positive. Within the broader taxonomy, the NCV801A sits under analog comparator -> comparator -> amplifier/comparator IC -> semiconductor. Push-pull CMOS output topology differs from open-drain comparators (such as the classic LM393) by actively driving both high and low states, enabling faster edges and lower power in many applications. This category of comparator is essential in any mixed-signal system requiring fast logic-level translation from analog signals. Key features include 1.8 V to 5.5 V single-supply operation, 200 mV beyond-the-rails input common-mode range, 50 ns typical propagation delay (100 mV overdrive), push-pull CMOS output, low quiescent current, and automotive-grade NCV prefix indicating PPAP-capable qualification per onsemi's automotive quality program. The 5-TSOP package consumes only a few square millimeters of PCB area, ideal for compact sensor and signal-conditioning modules. The NCV2250 is built on a standard CMOS process with on-chip ESD protection diodes on the inputs and outputs. The rail-to-rail input stage uses a complementary differential pair topology that maintains linear behavior across the full common-mode range. Internally, hysteresis can be introduced via external positive feedback resistors to prevent output chattering on slow-moving inputs. The NCV2250SN2T3G is functionally identical to the NCS2250SN2T3G except for automotive-grade qualification and traceability. Typical applications include zero-crossing detectors for line-voltage sensing, battery voltage monitoring in 12 V automotive systems, window comparators with multi-threshold detection, motor control feedback loops, sensor signal conditioning for microcontroller ADC front-ends, and threshold alarms in industrial control. The wide input common-mode range is particularly valuable for current-sense applications where the sense resistor sits at a high common-mode voltage close to the supply rail. When designing with this part, ensure input signals stay within the ESD rating of the device and consider adding small input series resistance to limit fault current during over-voltage transients. Decoupling the supply pin with a 100 nF ceramic capacitor placed within 3 mm of the VCC pin is essential for stable high-frequency switching performance. This page synthesizes distributor inventory, the parametric equivalent on the manufacturer's cross-reference database, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi
The onsemi NCV2904DR2G is a single-supply dual operational amplifier in an 8-pin SOIC (Case 751) package, operating from 3.0 V to 26 V with a common-mode input range extending to ground/VEE, targeted at automotive-grade applications. An operational amplifier (op-amp) is a high-gain differential voltage amplifier that sits within the analog signal chain hierarchy: op-amp -> amplifier IC -> analog IC -> semiconductor. Dual op-amps integrate two independent amplifier cores in one package, halving board space and BOM line items versus two singles. Single-supply op-amps like the NCV2904 are specifically designed for input common-mode ranges that reach the negative rail, making them usable directly on ground-referenced sensor signals without negative supplies. Key features of the NCV2904 include low power drain, short-circuit protected outputs, a true differential input stage, internally compensated frequency response, and ESD clamps on the inputs. The NCV prefix designates onsemi automotive qualification and temperature screening, making this device suitable for under-hood and body-electronics environments. Per the onsemi datasheet, the LM358 series is equivalent to one-half of an LM324, positioning the NCV2904 as the automotive member of this industry-standard family. Technically, the NCV2904 uses the circuit designs perfected for the quad LM2904/LM324 family: an internally compensated architecture that provides unity-gain stability without external compensation components. Single-supply or split-supply operation gives designers flexibility across 3.0 V to 26 V rails, and the input bias currents are low, minimizing offset errors with high-impedance sensors. Typical applications include automotive sensor signal conditioning (throttle position, pressure), battery-voltage monitoring dividers, comparators for window detection in ECUs, and general industrial signal amplification on single 5 V to 24 V rails. A key design consideration: the output cannot swing to the positive rail, so gain-setting must keep target output levels below the VOH specification at the expected load current. This page synthesizes distributor availability, drop-in alternatives across the LM258/LM358/LM2904 family, and practical design notes beyond what the manufacturer datasheet states.
NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi
The onsemi NE5532AD8 is a dual high-performance, internally-compensated low-noise operational amplifier supplied in an 8-pin SOIC (SO-8, "D8" suffix) surface-mount package. The device integrates two independent op-amp channels with input-protection diodes, output short-circuit protection, very low equivalent input noise voltage of about 5 nV/√Hz typical at 1 kHz, a high unity-gain bandwidth of 10 MHz, a 9 V/µs slew rate, and a 600 Ω drive capability, all from a single dual-supply rail of ±3 V to ±20 V (or single-supply 6 V to 40 V). An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. It is the fundamental analog building block inside audio preamplifiers, active filters, instrumentation stages, servo loops, ADC input buffers, and DAC output I/V converters. The NE5532 family belongs to the "low-noise audio" op-amp class — a category that improves upon generic parts such as the 1458 by combining low voltage noise, wide bandwidth, and strong output drive into one device. Key features include low harmonic distortion (typically 0.002 % at 1 kHz into 600 Ω), high output current that can drive 600 Ω headphone loads directly, large output voltage swing (≈ ±13 V on ±15 V supplies), and excellent channel separation around 110 dB at 1 kHz. The "A" suffix denotes the higher-precision NE5532A variant with tighter input-offset voltage (typically 0.5 mV versus 0.5 mV for the non-A) and improved AC characteristics versus the original NE5532, while remaining pin-compatible with the standard NE5532 socket. Architecturally, the NE5532A uses a bipolar-junction input stage with emitter-degeneration resistors, a PNP common-emitter second stage, and an NPN class-AB output stage. Compensation is built into the die (no external capacitor required), which simplifies PCB design but caps stable unity-gain operation. Designers should treat the device as a "single-supply-unfriendly" part when planning ground-referenced single-rail circuits; a mid-rail bias is required for true ground sensing. Typical applications include high-fidelity audio preamplifiers, mixing consoles, microphone preamps, RIAA phono stages, line drivers, active crossovers, test-instrumentation signal conditioners, and ADC/DAC interface buffers. The 8-pin SOIC footprint is well-suited to high-density PCB designs and is one of the most widely supported DIP-socket IC sockets on adapter boards. When designing with the NE5532AD8, derate output current with increasing junction temperature, mind the input common-mode range that does not include the negative rail, and provide a solid ground pour for the exposed copper pad of the SOIC to keep the junction temperature below 150 °C. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi
onsemi NE5532AD8G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and two amplifier circuits in an 8-pin SOIC package. It is intended for audio, instrumentation, and control applications where low noise and improved output drive are important. The device is specified for dual supplies of ±3 V to ±20 V and commercial-temperature operation. A dual operational amplifier combines two independent amplifiers in one package. The NE5532A family belongs to the operational-amplifier hierarchy, within analog signal-conditioning and active-control systems. Its internally compensated design simplifies use in non-inverting, inverting, and feedback configurations without an external compensation network, while its low-noise characteristics make it useful when signal integrity must be preserved through amplification. The verified NE5532AD8G data identifies a 10 MHz gain-bandwidth product, 9 V/µs slew rate, 200 nA input-bias current, 500 µV input-offset voltage, 8 mA supply current, and a 3 V to 20 V supply range in the distributor listing. The dual SOIC package provides two circuits in one component, reducing board area compared with separate single amplifiers. Its improved output-drive capability and small-signal bandwidth distinguish it from basic general-purpose dual op amps. Typical uses include stereo audio preamplification, mixer stages, active filters, microphone and line-level signal conditioning, test equipment, and industrial control circuits. In audio designs, the low-noise architecture helps preserve quiet signal paths, while the 9 V/µs slew rate supports higher-frequency transients when the circuit bandwidth and load permit. In instrumentation applications, the two amplifiers can process complementary or sequential channels. The primary design consideration is supply and load compatibility. Confirm the dual-supply range against the system rails, check input and output swing limits for the selected gain, and place decoupling capacitors close to the supply pins. Stable feedback-network layout, adequate output-current capability, and thermal margin should be checked against the actual signal amplitude and frequency. No SOA applies because this is a linear operational amplifier rather than a power semiconductor.
NE5532AD8R2 - Dual 10MHz Low-Noise Op Amp | onsemi
The onsemi NE5532AD8R2 is an internally compensated, dual low-noise operational amplifier with a 10 MHz gain-bandwidth product, packaged in an 8-pin SOIC. It combines two amplifier channels in one package for audio, instrumentation, and general-purpose signal-processing circuits where low-noise performance and moderate bandwidth are important. The device operates from ±3 V to ±20 V and is specified at 38 mA per channel, with 200 nA of input bias current, 70 dB common-mode rejection ratio, and 1 µA maximum input offset current. An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and drives its output to amplify the difference between them. The NE5532 belongs to the internally compensated operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Internal compensation makes the amplifier stable without an external compensation network, simplifying conventional audio and instrumentation designs. Its dual-channel configuration reduces component count and board area when two gain stages are required. The NE5532AD8R2 is specifically described as a low-noise dual amplifier. Its 10 MHz gain-bandwidth product supports audio-frequency amplification and general closed-loop signal conditioning, while the 70 dB common-mode rejection helps reject common-mode disturbance on differential inputs. The low 200 nA input bias current can simplify biasing of higher-impedance source networks, although the supplied data does not establish input impedance, input capacitance, slew rate, or output-current capability. Typical uses include stereo audio preamplification, active equalization, low-level microphone-stage amplification, instrumentation buffering, and dual-channel analog filtering. In a preamplifier, the device can be configured as a non-inverting stage with feedback resistors, while the two internal channels can process left and right signal paths independently. In instrumentation circuits, the dual format can support gain and active filtering functions without requiring two separate amplifier packages. Designers should preserve the SOIC-8 footprint and verify the exact channel pin assignments against the manufacturer datasheet before layout release. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels require appropriate input termination rather than being left floating. Input and output swings, gain-bandwidth behavior, stability, and output-current limits must be checked against the circuit operating conditions. This page consolidates the verified onsemi and distributor information, provides package-level selection guidance, and distinguishes electrically similar candidates from confirmed drop-in replacements. Pricing, lifecycle classification, exact pin names, and several detailed electrical parameters remain explicitly marked where the supplied source data does not provide authoritative values.
NE5532AD8R2G - Dual Low-Noise Amplifier | onsemi
The onsemi NE5532AD8R2G is a dual, internally compensated, low-noise operational amplifier rated for 3 V to 20 V supply operation and supplied in an 8-pin SOIC package. It provides two amplifier channels in one package, making the device suitable for professional audio, instrumentation, signal conditioning, active filtering, test and measurement, and general-purpose analog designs. The verified distributor descriptions identify the NE5532AD8R2G as a standard general-purpose amplifier with two circuits and an 8-SOIC package. An operational amplifier is an analog building block that amplifies the voltage difference between its non-inverting and inverting inputs. Internally compensated operational amplifiers include frequency-compensation circuitry that establishes a stable operating characteristic without requiring an external compensation capacitor. Within the broader semiconductor hierarchy, an operational amplifier belongs to the linear-amplifier and signal-conditioning IC family, where low noise, output-current capability, slew rate, and input bias behavior determine its suitability for sensitive analog signals. The NE5532 family is specifically associated with low-noise audio and instrumentation operation. A dual-channel configuration reduces the number of packages required when two amplifier sections are needed, while the 8-pin SOIC format supports conventional surface-mount assembly. The Mouser listing specifies a 3 V to 20 V operating range, and the Arrow listing describes the device as a dual low-noise amplifier with an automotive AEC-Q100 option. These characteristics make the amplifier relevant to signal paths where low-noise performance and adequate output drive are more important than very small package area. The NE5532/SE5532 device family is described by onsemi as an internally compensated dual low-noise operational amplifier. Compared with general-purpose operational amplifiers, the NE5532 family was developed for improved noise performance and applications such as high-quality audio equipment and instrumentation. Two independent amplifiers can implement noninverting, inverting, summing, active-filter, buffer, and feedback-control stages, although each channel requires appropriate supply decoupling and feedback-network design. Typical applications include audio preamplifiers and mixer stages, microphone preamplification, active crossover and equalization networks, low-level sensor signal conditioning, laboratory instrumentation, oscilloscope input drivers, and audio interface circuits. In each case, the dual SOIC package can simplify board layout by placing two related amplifier functions close together. The low-noise characterization is particularly valuable when the source impedance is high or when the output must preserve small signals without adding unnecessary circuit noise. When designing around the NE5532AD8R2G, engineers should verify the exact input common-mode range, output swing, slew rate, input bias current, and channel-to-channel behavior against the manufacturer datasheet for the selected operating conditions. Input and output bypassing capacitors should be placed close to the relevant pins, and feedback components should be selected for the intended gain and bandwidth. Power-supply noise can also enter an audio or instrumentation path, so clean supply distribution remains as important as the amplifier itself. This product page combines the verified distributor and manufacturer-related source information with package, sourcing, comparison, and design guidance. It distinguishes published facts from unavailable parameters, preserves the original NE5532AD8R2G ordering code, and identifies only same-package drop-in candidates for engineering review. Final component selection should always include a full datasheet, pinout, and application-specific comparison before PCB substitution.
NE5532ADR - 30V, 10MHz Dual Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5532ADR is a dual low-noise operational amplifier for audio applications, specified for ±5 V to ±15 V supplies, with a 10 MHz gain-bandwidth product and 9 V/µs slew rate, housed in an 8-pin SOIC package. The device combines two amplifiers in one package and is intended for low-noise audio preamplification, mixing, filtering, and similar signal-conditioning circuits. An operational amplifier is a voltage-feedback amplifier whose open-loop gain is used to create closed-loop gain with external feedback components. The low-noise operational amplifier category is part of the broader analog signal-processing hierarchy: operational amplifier, analog IC, and semiconductor. NE5532-family devices became established choices in audio circuitry because they combine low input noise, adequate bandwidth, high slew rate, and wide supply-voltage capability in a conventional through-hole-compatible or surface-mount package. Key verified attributes include a 30 V maximum supply rating, dual-amplifier configuration, 10 MHz bandwidth, 9 V/µs slew rate, and operation over ±5 V to ±15 V. According to the Texas Instruments manufacturer datasheet, the NE5532x grade is specified from 0°C to 70°C, while the electrically similar SA5532x grade extends the operating range to -40°C to +85°C. These distinctions matter when selecting between commercial-temperature and industrial-temperature versions. The NE5532ADR uses the standard dual-operational-amplifier arrangement, allowing each amplifier to be configured independently for non-inverting, inverting, summing, filtering, or active-amplifier functions. Its 8-pin SOIC package supports compact, surface-mount PCB construction while preserving a conventional dual-op-amp footprint. Designers should still verify output-current, output-voltage swing, input-bias-current, noise-density, and open-loop-gain requirements against the complete manufacturer electrical-characteristics tables. Typical applications include stereo audio preamplifiers, active crossover filters, microphone preamplifiers, line-level mixers, and small-signal audio output stages. Its 10 MHz bandwidth is well above the audible band, while its low-noise designation makes it appropriate for amplifying weak audio signals without adding unnecessary broadband noise. The 9 V/µs slew rate also helps preserve low distortion when processing larger transient waveforms. The primary design consideration is power-supply configuration. The manufacturer datasheet specifies operation from ±5 V to ±15 V, and dual-supply operation generally simplifies bipolar audio-signal handling around ground. Designers must observe the output-swing limits, avoid excessive capacitive loading, and maintain suitable decoupling close to the supply pins. Stable feedback networks and appropriately chosen compensation or load conditions are important for reliable closed-loop operation. This page combines verified manufacturer and distributor information with pinout guidance, practical application fit, drop-in comparison data, and engineering-focused selection notes. The comparison also distinguishes true pin-compatible options from devices that may sound different or require different supply and stability considerations.
NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI
The Texas Instruments NE5532ADRE4 is a dual, general-purpose low-noise operational amplifier with a 10 MHz unity-gain bandwidth, 9 V/µs slew rate, and typical equivalent input noise voltage of 5 nV/√Hz at 1 kHz, supplied in an 8-SOIC package. It is intended for audio applications operating from ±5 V to ±15 V, with the NE5532x grade specified over 0°C to 70°C. Both amplifier channels share the same compact surface-mount package, allowing one component to support stereo signal paths. A low-noise operational amplifier is an analog integrated circuit that amplifies voltage differences while contributing minimal intrinsic noise. The NE5532 belongs to the operational-amplifier hierarchy used for audio preamplification, mixing, buffering, filtering, and instrumentation. Its 5 nV/√Hz typical input-noise characteristic is especially relevant when the amplified signal is sourced from a high-impedance sensor or a low-level microphone. The device provides 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, 100 dB typical common-mode rejection, and 100 V/mV typical DC voltage gain. These characteristics support audio-band operation with ample bandwidth for feedback networks and active filters. The dual configuration reduces component count in stereo circuitry, while the 8-SOIC package is compatible with automated surface-mount assembly. The NE5532 uses a conventional voltage-feedback operational-amplifier architecture with two independent amplifiers. Each channel provides inverting and non-inverting inputs, an output, and a power-supply connection. Noise and common-mode rejection are important because they influence the signal-to-noise ratio and the degree to which unwanted supply or common-mode signals appear at the output. Operating from a dual supply also supports bipolar audio signals without biasing the source at mid-rail. Typical applications include stereo audio preamplifiers, microphone amplifiers, line-level mixers, tone-control circuits, active crossover networks, and low-level audio buffers. In each case, the low-noise input stage helps preserve small signals, while the 10 MHz bandwidth and 9 V/µs slew rate provide margin for gain and phase shaping. Designers must still verify stability with the selected feedback network and load. The principal design consideration is power-supply bypassing. Place the required input and output decoupling capacitors close to the device pins, keep output routing short, and avoid placing long traces beside noisy switching nodes. Decoupling values and stability guidance should be taken directly from the manufacturer datasheet and typical application circuit rather than inferred from the distributor summaries. This page combines verified manufacturer information, distributor pricing, pin-compatible substitute references, and practical application guidance. The alternatives are explicitly limited to same-package drop-in candidates, while unavailable electrical details remain marked for validation against each candidate manufacturer’s current datasheet.
NE5532ADRG4 - Dual 10 MHz Low-Noise Op Amp | Texas Instruments
Texas Instruments NE5532ADRG4 is a dual, general-purpose operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and 5 nV/√Hz typical equivalent input-noise voltage at 1 kHz, housed in an 8-pin SOIC package. The device provides two independent amplifiers and a 100 dB typical common-mode rejection ratio for audio, instrumentation, filtering, and low-level signal-conditioning applications. An operational amplifier is an active analog signal-conditioning device that uses high-gain differential feedback to amplify the difference between its two inputs. The dual NE5532 family belongs to the operational-amplifier hierarchy within analog and amplifier ICs. Its two channels can amplify noninverting and inverting signals independently, making it suitable for preamplifiers, active filters, mixers, buffers, and control loops where low noise, moderate bandwidth, and relatively high output-current capability are useful together. The NE5532ADRG4 combines a 10 MHz typical unity-gain bandwidth with 9 V/µs typical slew rate. Its typical high DC voltage gain is 100 V/mV, while the equivalent input-noise voltage is 5 nV/√Hz at 1 kHz. These characteristics support low-distortion audio signal paths and general feedback-control circuits without requiring a high-speed bipolar or current-feedback amplifier. Internally, the device uses a bipolar-compatible low-noise amplifier architecture intended for general-purpose precision audio work. Noise performance is especially important when the circuit handles microphone-level, musical-instrument, or balanced-line signals because amplifier noise can establish the input-referred noise floor. The common-mode rejection specification supports rejection of shared interference on differential inputs, while the two-amplifier configuration reduces package count in balanced and stereo circuits. Typical uses include stereo audio preamplification, active equalizer and crossover stages, microphone and line-level signal conditioning, instrumentation buffers, and low-frequency filter networks. In a preamplifier, both channels can process left and right signals while preserving low-noise performance. In an active filter, the 10 MHz bandwidth provides more open-loop capability than the audio-band signal being shaped, although stability must be verified for the selected noise gain and load. Designers should keep feedback-loop compensation appropriate for the selected gain, check output swing into the intended load, and provide stable decoupling at the supply pins. Because the available verified data does not state the complete supply-voltage range, input common-mode limits, output-current limits, or thermal resistance, those values must be confirmed in the manufacturer datasheet before final design release. This product page consolidates verified distributor specifications, pricing context, same-package replacement candidates, and application-oriented engineering guidance. It separates documented facts from unavailable parameters, helping engineers evaluate the NE5532ADRG4 quickly without mistaking an incomplete web summary for a complete electrical characterization.
NE5532AN - Dual Low-Noise 10 MHz Op Amp | onsemi
The onsemi NE5532AN is a dual, high-performance, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin DIP package measuring 0.300 inch (7.62 mm). Compared with standard general-purpose operational amplifiers, the NE5532 family provides improved noise performance, stronger output drive capability, and better small-signal and power-bandwidth performance. A low-noise operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its two inputs while seeking low added noise and low distortion. In the product hierarchy, the NE5532AN belongs to the operational-amplifier family, which is part of amplifier ICs and, more broadly, analog semiconductors. Its two amplifiers share one package while providing independent input, output, and supply connections. The principal verified characteristics include a dual amplifier configuration, internally compensated operation, a 10 MHz gain-bandwidth product, and an 8-DIP package. The associated NE5532x family is specified for operation over a ±5 V to ±15 V supply range. The commercial NE5532x temperature range is stated as 0°C to 70°C, while the SA5532x family is specified from -40°C to +85°C. Exact input-offset, input-bias-current, output-voltage, and output-current limits were not included in the supplied data and therefore remain unspecified on this page. Internally compensated operation allows each amplifier to operate as a stable closed-loop stage without an external compensation network. This simplifies analog circuit design while preserving the low-noise characteristics valued in audio equipment. The stronger output-drive capability described in the manufacturer data helps the amplifier maintain low distortion when driving the next stage or a termination load. The 10 MHz gain-bandwidth figure provides useful bandwidth for low-frequency signal conditioning and audio preamplification rather than high-speed instrumentation applications. Typical uses include stereo audio preamplifiers, active tone-control stages, mixer input stages, headphone-driver interfaces, active crossover filters, and low-level signal conditioning. Its dual configuration is particularly useful when a board needs two similar amplifier channels, such as left and right audio paths. For lower-voltage or extended-temperature requirements, the related SA5532x grade should be evaluated separately rather than assuming NE5532AN covers those conditions. The primary design consideration is supply-headroom management: the stated family specification applies from ±5 V to ±15 V, so the circuit must remain within that operating range at every temperature and load condition. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier in a dual package should be configured according to the manufacturer guidance rather than left floating. This page consolidates the verified package, supply-range, temperature-class, bandwidth, and cross-reference information for the NE5532AN, then adds application guidance, strict same-package drop-in comparisons, and practical selection criteria for engineers evaluating this dual low-noise operational amplifier.
NE5532AP - Dual Low-Noise Op Amp, 10MHz, 8-PDIP | Texas Instruments
The Texas Instruments NE5532AP is a dual high-performance, low-noise operational amplifier supplied in an 8-pin PDIP (through-hole) package. Each of the two internal op-amps delivers 10 MHz unity-gain bandwidth, a 5 nV/√Hz input noise voltage at 1 kHz, 100 dB typical CMRR, and a 100 V/mV typical DC voltage gain. The device is specified for ±5 V to ±15 V dual supply operation and drives 600 ohm loads directly, making it a workhorse in professional and consumer audio designs. An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. Within the broader taxonomy, an op-amp belongs to the linear IC family -> amplifier ICs -> analog signal conditioning -> semiconductor. Low-noise audio-grade op-amps such as the NE5532 are designed to add minimal hiss and distortion when placed in the signal path of pre-amplifiers, mixers, equalizers, and line drivers, distinguishing them from general-purpose op-amps (e.g., TL072) that trade noise performance for cost or bandwidth. Key differentiating features of the NE5532AP include: 5 nV/√Hz equivalent input noise voltage (typ. at 1 kHz), 32 V peak-to-peak output swing with ±18 V supplies into 600 ohm, input protection diodes, output short-circuit protection, and a high slew rate that enables clean transient response in fast audio signals. The 8-PDIP package simplifies prototyping on breadboards and through-hole production boards, and is widely accepted in long-lifecycle industrial products where socketing and field replacement are valued. Architecturally, the NE5532 uses a bipolar transistor input stage and a class AB output stage. The bipolar front-end delivers the low voltage noise and high DC gain that JFET-input op-amps cannot match, at the cost of higher input bias current (which is acceptable in audio-coupling networks with series capacitors). The 600 ohm drive capability means the NE5532AP can directly feed pro-audio line inputs without an additional buffer. Typical applications include studio-quality microphone pre-amplifiers, mixing consoles, equalizer and crossover filter boards, audio DAC output buffers, headphone amplifiers, and instrumentation front-ends. The wide supply range also allows use in industrial control signal conditioning where dual rails are already present. When designing with the NE5532AP, observe the input common-mode range: the inputs must stay within the supply rails, and large differential voltages should be limited by external series resistance to avoid damaging the input-protection structures. Decouple both supply pins with 100 nF ceramics placed within 10 mm of the device. This page consolidates distributor pricing, drop-in DIP-8 alternatives, and practical audio design notes - information not assembled in the manufacturer datasheet alone - to support BOM decisions for new designs and legacy maintenance.
NE5532APG4 - 10MHz Dual Audio Op Amp | Texas Instruments
The Texas Instruments NE5532APG4 is a dual general-purpose operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin dual in-line package. The verified distributor data identifies two amplifier circuits, a general-purpose audio classification, and a through-hole 8-DIP package measuring 0.300 inches with 7.62 mm lead pitch. One distributor reports a $0.6560 unit price and 4,320 pieces in stock as of 2026-10-22. An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, filter noise, and drive feedback-controlled circuits. A dual amplifier contains two amplifier channels in one package. The NE5532 family is especially recognizable in audio signal paths because it is commonly associated with low-noise audio preamplification, mixing, and output-stage applications. Within the broader hierarchy, it is an amplifier IC, an analog integrated circuit, and a general-purpose semiconductor. The available data confirms two amplifier circuits and a 10 MHz bandwidth-related figure, while the manufacturer-specific electrical limits were not included in the supplied source set. Accordingly, specifications for supply voltage, input offset voltage, input-bias current, noise density, output swing, slew rate, operating temperature, and channel-to-channel matching are marked as needing primary-source verification. This conservative approach prevents generic NE5532-family figures from being presented as verified facts for this exact suffix and package. Its 8-DIP package is appropriate for prototypes, educational instruments, repair work, and through-hole audio boards where socketed replacement is useful. The larger package also makes the part straightforward to probe and exchange, although it occupies more PCB area than a surface-mount dual op amp. Circuit layout still requires short feedback paths, clean grounding, and appropriate supply bypassing to preserve stability and low-noise performance. Typical uses include stereo audio preamplification, active tone control, headphone-buffer stages, mixer input conditioning, and general low-frequency signal processing. These applications align with the device's stated general-purpose amplifier classification and dual-channel configuration. Exact stability, bandwidth, noise, and output-drive claims should be checked against the official Texas Instruments datasheet before setting gain-bandwidth requirements. For new designs, verify the exact NE5532APG4 suffix, supply rails, input common-mode range, output swing, and thermal conditions in the manufacturer datasheet. When repairing an existing board, preserve the original pin orientation and socket the device only after confirming that the installed part is electrically and mechanically compatible. The 7.62 mm pitch through-hole package is mechanically different from common SOIC-8 variants even where some signal functions resemble them. This page consolidates verified distributor availability, package information, pricing, cross-reference research, and practical replacement guidance beyond a raw distributor listing. Unknown electrical values are deliberately identified rather than inferred from the broader NE5532 family.
NE5532APSRE4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5532APSRE4 is a dual general-purpose operational amplifier with a 10 MHz unity-gain bandwidth, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 100 dB typical common-mode rejection ratio. The device is supplied in an 8-pin SOIC package and operates from 0°C to 70°C. Each package contains two independent low-noise amplifiers suitable for audio, instrumentation, filtering, and general signal-conditioning applications. An operational amplifier is an analog integrated circuit that provides high open-loop gain and uses negative feedback to amplify, buffer, filter, or control voltage signals. Within the semiconductor hierarchy, the NE5532 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC categories. It combines low voltage noise, high common-mode rejection, a 9 V/µs typical slew rate, and a 100 V/mV typical high DC voltage gain in a common surface-mount package. Key features include two amplifier circuits, 10 MHz typical gain-bandwidth product, 5 nV/√Hz typical input noise at 1 kHz, 100 dB typical CMRR, and a 15 V typical or maximum supply figure identified in the retrieved specifications. The 8-SOIC package measures approximately 5.30 mm in width according to the distributor listing. Tape-and-reel ordering is identified by the E4 suffix, making the part suitable for standard automated surface-mount assembly and replenishment processes. The device uses complementary input and output stages to deliver low-noise voltage amplification. Its unity-gain bandwidth makes it suitable for audio-frequency and moderate-bandwidth signal paths, while its high CMRR helps reject common-mode interference. The 9 V/µs slew rate supports reasonably rapid signal transitions. Designers should still verify output-voltage swing, input common-mode range, supply limits, and stability against their individual operating conditions before finalizing a circuit. Typical applications include stereo audio preamplifiers, active crossover and equalization networks, microphone-level conditioning, test-equipment input buffers, low-frequency active filters, and general-purpose analog signal processing. One amplifier section may drive or process one audio channel, allowing the dual package to support stereo or balanced two-channel circuitry while reducing board area. For stable operation, place the input, output, feedback, and compensation components close to the device and use a clean, low-impedance ground reference. Decoupling should follow the manufacturer datasheet recommendations. Avoid operating the amplifier at a gain where its internal compensation and board parasitics produce instability, and verify the common-mode input range whenever signals approach either supply rail. This product page consolidates the verified 10 MHz bandwidth, noise, CMRR, slew-rate, package, temperature, and observed distributor pricing data with application guidance, engineering design notes, and drop-in replacement information. It also distinguishes electrically useful alternatives from options that require pinout or application-specific verification.
NE5532D - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments (Tape & Reel)
The Texas Instruments NE5532D is a dual low-noise operational amplifier for audio applications, with two amplifier circuits, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 10 MHz typical unity-gain bandwidth in an 8-pin SOIC package. It is specified for total supply voltages from 10 V to 30 V, equivalent to ±5 V through ±15 V operation, making it suitable for conventional dual-polarity audio signal paths. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. Within the broader hierarchy, the NE5532 is a dual operational amplifier, a low-noise voltage-feedback amplifier, and a linear amplifier used in audio preamplifiers, mixing consoles, active filters, and line-level driver circuits. Its two independent channels make it suitable for stereo audio or paired mono signal processing. Key characteristics include 5 nV/√Hz typical input noise at 1 kHz, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 10 V/μs typical slew rate, and a typical 100 dB common-mode rejection ratio. The device also provides rail-to-rail output swing under the specified load conditions and low-distortion operation. The manufacturer identifies the NE5532 family for audio applications rather than precision instrumentation or micropower systems. The NE5532x family uses a conventional bipolar operational-amplifier architecture optimized for low noise and audio bandwidth. Its performance depends on supply voltage, output loading, gain, frequency, and bypass-capacitor implementation. Because the specified operating range includes ±5 V to ±15 V, downstream circuit headroom and output-swing limits must be checked against the actual load rather than inferred from the nominal supply rating. Typical applications include stereo preamplifiers, headphone-buffer stages, active crossover filters, audio mixers, line amplifiers, and small-signal buffer circuits. The dual configuration reduces package count when two related audio channels are required. A design should still verify stability, output-current capability, thermal conditions, and the selected feedback network rather than assuming every audio circuit has the same optimum gain or loading. The primary design consideration is power-supply decoupling and clean grounding. Place suitable bypass capacitors close to the supply pins, keep input and feedback routing short, and avoid high-impedance nodes adjacent to the amplifier inputs. The SOIC-8 package is a surface-mount SOIC family package intended for PCB assembly rather than through-hole insertion. This page combines the verified manufacturer and distributor information for NE5532D with package, application, design, and procurement context. Alternative substitutions are shown only where the retrieved web material supports a credible cross-reference; unavailable pricing and electrical details remain explicitly marked rather than inferred.
NE5532D8 - Dual Low-Noise Op Amp | onsemi
The onsemi NE5532D8 is a dual, internally compensated, low-noise operational amplifier packaged in an 8-pin SOIC. The verified product data identifies a 10 MHz gain-bandwidth product, a 3 V to 20 V supply range, and operation from ±3 V to ±20 V. Its two amplifiers share one package while providing independent input, output, and supply connections, making the device suitable for stereo audio, instrumentation, control, and telephone-channel applications. An operational amplifier is an analog integrated circuit that compares an input voltage with a feedback-derived reference and drives its output to reduce the difference between them. A dual operational amplifier combines two amplifiers in one package. Within the broader semiconductor hierarchy, this device belongs to the amplifier-IC family and supports precision analog signal conditioning when low noise, adequate bandwidth, and practical output-drive capability are important. The NE5532 family is specifically described as a high-performance, low-noise dual amplifier with improved noise performance, output drive, small-signal performance, and power-bandwidth behavior compared with standard devices such as the 1458. It is internally compensated for unity-gain operation, allowing use as a voltage follower without an external compensation network. The verified listing also associates the device with professional audio, instrumentation, control circuits, and telephone channel amplifiers. Use NE5532D8 where two related analog channels share one compact surface-mount package, particularly in low-noise audio signal paths. Its 10 MHz bandwidth provides more than enough bandwidth for many audio and general analog functions, while dual integration reduces component count compared with two separate single amplifiers. Designers should still verify gain, load, output swing, supply headroom, noise, and stability against the complete manufacturer datasheet before release. The D8 suffix identifies the verified 8-pin SOIC orderable offered by onsemi in the supplied distributor result. Place input and feedback components close to the relevant amplifier pins, maintain a continuous return path, and decouple the supply pins close to the package. Avoid leaving unused inputs floating; terminate them consistently with the chosen noise and bias-current strategy. This page consolidates verified distributor information, the manufacturer datasheet, strict package and pin constraints, and design guidance for NE5532D8. It distinguishes documented dual-amplifier functionality from unverified specifications by marking missing electrical details rather than estimating them.
NE5532D8G - Dual Low-Noise Operational Amplifier | onsemi
onsemi NE5532D8G is a dual, internally compensated low-noise operational amplifier with two amplifier circuits, a 10 MHz gain-bandwidth product, and a 9 V/us slew rate in an 8-SOIC package. The verified distributor data identifies it as a general-purpose commercial-temperature amplifier covering 3 V to 20 V and classifying it for instrumentation, audio, and buffer-amplifier applications. A low-noise operational amplifier is a voltage-feedback amplifier designed to amplify weak signals while minimizing broadband noise. In the broader semiconductor hierarchy, the NE5532 belongs to operational amplifiers, analog amplifiers, integrated circuits, and signal-chain conditioning components. Its two integrated channels can process left and right audio signals, support instrumentation stages, or implement active filtering and buffering when the circuit operates within the manufacturer’s electrical limits. The principal verified features are dual-circuit integration, internal compensation, 1 uV input-noise class behavior, approximately 10 MHz bandwidth, and a 9 V/us slew rate. The low-noise characteristic is particularly useful in audio preamplifiers, where input-referred noise influences the audible signal floor. Its 10 MHz bandwidth also makes it more responsive than general-purpose precision amplifiers commonly used for slower instrumentation functions. Mouser describes the device as a dual low-noise commercial-temperature amplifier for a 3 V to 20 V supply range. The NE5532 architecture provides one amplifier per channel, with no external compensation network required. Verified sources describe low distortion, strong output-drive capability, high small-signal and power bandwidth, input-protection diodes, and output short-circuit protection. These characteristics make it suitable for preamplifier gain stages, active filters, instrumentation, test equipment, and general low-frequency analog signal conditioning. Exact noise density, input-offset voltage, common-mode range, output-current capability, and temperature limits require confirmation from the manufacturer datasheet. When laying out an NE5532D8G board, preserve the SOIC-8 land pattern and observe the manufacturer’s input, output, supply, and bypass recommendations. Place supply-decoupling capacitors close to the supply pins and use short, low-loop feedback paths to reduce oscillation risk. Because audio and instrumentation circuits are sensitive to grounding and supply noise, a quiet reference return, symmetrical routing, and appropriate output-load compatibility are as important as nominal gain calculations. This product page combines verified distributor identification, source-linked availability information, exact known electrical values, and explicit data markers for unsupported specifications. It is intended to help engineers distinguish verified NE5532D8G attributes from unverified claims before making an audio, instrumentation, or analog-signal-chain design decision.
NE5532D8R2 - Dual Low-Noise Op Amp | onsemi | Audio
The onsemi NE5532D8R2 is a dual, internally compensated low-noise operational amplifier with two independent amplifiers in an 8-pin SOIC package. The verified distributor listing identifies the device as a standard general-purpose amplifier with a 2-circuit configuration and an 8-SOIC package. It is intended for audio, instrumentation, filtering, and signal-conditioning circuits where two channels and low-noise performance are useful. The verified sources also describe it as a 3 V to 20 V dual low-noise operational amplifier. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback. A dual operational amplifier contains two amplifier channels in one package, allowing a circuit to process two related signals or to build stereo, differential, or multi-stage analog functions. The internally compensated architecture simplifies stable operation in typical closed-loop analog applications, while the low-noise characteristics make the device relevant to audio and measurement circuits. The NE5532 family is commonly associated with audio preamplification, microphone stages, active filters, and general instrumentation. The verified search results specifically describe the NE5532D8R2 as an internally compensated dual low-noise operational amplifier and identify its package as 8-SOIC. They do not provide a complete manufacturer electrical table, so detailed values such as input noise density, slew rate, bandwidth, common-mode range, output swing, input bias current, and temperature limits are marked as data needed rather than inferred. Typical circuit implementation places each amplifier channel in a feedback network, with external resistors setting closed-loop gain and filtering behavior. Decoupling capacitors should be placed close to the supply pins, and the unused channel should be configured according to the manufacturer’s recommended practice rather than left floating. The SOIC footprint supports conventional surface-mount assembly, although actual board layout, thermal behavior, and signal integrity still require validation. NE5532D8R2 pricing and detailed electrical performance must be confirmed against current authorized distributor inventory and the manufacturer datasheet. The verified distributor page reports current purchasing access, but the supplied data does not include numeric prices, stock quantities, or lead times. This page therefore distinguishes verified catalog facts from specifications requiring datasheet confirmation.
NE5532D8R2G - 10 MHz Dual Low-Noise Op Amp | onsemi
The onsemi NE5532D8R2G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, a 3 V to 20 V supply range, and an 8-SOIC package. It contains two amplifier circuits in one package and is classified as a standard general-purpose amplifier for commercial-temperature instrumentation, audio, filtering, and signal-conditioning equipment. An operational amplifier is a voltage-gain building block used within the broader semiconductor and analog integrated-circuit hierarchy. The NE5532 family combines low-noise voltage amplification with internally compensated operation, reducing the external compensation components normally required to stabilize a feedback amplifier. In signal paths, its role is to increase the voltage presented by a small source while preserving the intended signal bandwidth. The verified 10 MHz bandwidth supports applications requiring response beyond the audio baseband, while the dual circuit count lets one 8-SOIC package implement two independent amplifier sections. Its 3 V to 20 V operating supply span is suitable for conventional analog systems operating from regulated low-voltage rails through higher industrial-style supply voltages. The distributor listing specifically describes the device as an internally compensated dual low-noise operational amplifier. The NE5532 architecture is intended for general-purpose instrumentation rather than a specialized automotive-qualified product. Compared with the listed 10 MHz class of low-noise amplifiers, designers should examine noise density, distortion, output-current capability, input-bias current, unity-gain stability, and supply-current consumption against their exact circuit requirements. The verified data does not quantify every one of those electrical characteristics, so they should be confirmed in the manufacturer datasheet before final qualification. Typical uses include low-level audio preamplification, active filters, instrumentation signal conditioning, transducers, and general analog control loops. In each case, the device can provide two amplifier channels while maintaining a compact surface-mount footprint. The 8-SOIC format supports conventional PCB assembly and hand-soldering while avoiding the larger footprint of an equivalent dual DIP package. The principal design consideration is stability. Because the amplifier is internally compensated, a feedback network must be selected for the intended closed-loop gain and load. Designers should also verify output swing, input common-mode range, supply headroom, noise performance, and thermal margin using the manufacturer datasheet rather than relying on general NE5532-family assumptions. This page combines verified distributor availability and pricing, same-package replacement information, a parameter comparison, and practical selection guidance. It is intended to help engineers identify whether the NE5532D8R2G matches a dual, 8-SOIC, 10 MHz low-noise amplifier requirement before purchasing or redesigning an existing board.
NE5532DR - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments
The Texas Instruments NE5532DR is a dual low-noise operational amplifier for audio applications, with two amplifier circuits, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 10 MHz typical unity-gain bandwidth in an 8-pin SOIC package. It is specified for total supply voltages from 10 V to 30 V, equivalent to ±5 V through ±15 V operation, making it suitable for conventional dual-polarity audio signal paths. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. Within the broader hierarchy, the NE5532 is a dual operational amplifier, a low-noise voltage-feedback amplifier, and a linear amplifier used in audio preamplifiers, mixing consoles, active filters, and line-level driver circuits. Its two independent channels make it suitable for stereo audio or paired mono signal processing. Key characteristics include 5 nV/√Hz typical input noise at 1 kHz, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 10 V/μs typical slew rate, and a typical 100 dB common-mode rejection ratio. The device also provides rail-to-rail output swing under the specified load conditions and low-distortion operation. The manufacturer identifies the NE5532 family for audio applications rather than precision instrumentation or micropower systems. The NE5532x family uses a conventional bipolar operational-amplifier architecture optimized for low noise and audio bandwidth. Its performance depends on supply voltage, output loading, gain, frequency, and bypass-capacitor implementation. Because the specified operating range includes ±5 V to ±15 V, downstream circuit headroom and output-swing limits must be checked against the actual load rather than inferred from the nominal supply rating. Typical applications include stereo preamplifiers, headphone-buffer stages, active crossover filters, audio mixers, line amplifiers, and small-signal buffer circuits. The dual configuration reduces package count when two related audio channels are required. A design should still verify stability, output-current capability, thermal conditions, and the selected feedback network rather than assuming every audio circuit has the same optimum gain or loading. The primary design consideration is power-supply decoupling and clean grounding. Place suitable bypass capacitors close to the supply pins, keep input and feedback routing short, and avoid high-impedance nodes adjacent to the amplifier inputs. The SOIC-8 package is a surface-mount SOIC family package intended for PCB assembly rather than through-hole insertion. This page combines the verified manufacturer and distributor information for NE5532DR with package, application, design, and procurement context. Alternative substitutions are shown only where the retrieved web material supports a credible cross-reference; unavailable pricing and electrical details remain explicitly marked rather than inferred.
NE5532DR2G - Dual 10 MHz Low-Noise Op Amp | onsemi
The onsemi NE5532DR2G is an internally compensated dual low-noise operational amplifier supplied in a 16-SOIC package. The verified product data identifies a 10 MHz gain-bandwidth product, low-noise performance, improved output drive capability, and substantially higher small-signal and power bandwidth than older standard amplifiers such as the 1458. Each package contains two amplifiers, allowing stereo audio, balanced signal, or dual-channel instrumentation designs to use one IC rather than two single-channel devices. An operational amplifier is a voltage-controlled voltage-source amplifier that uses negative feedback to make its closed-loop behavior stable and predictable. The NE5532 belongs to the low-noise operational-amplifier hierarchy within analog and linear ICs. Its dual-channel architecture is useful wherever two related signals must be amplified with matched circuitry, while internal compensation avoids an external compensation network in ordinary closed-loop applications. The verified material specifically describes better noise performance, improved output drive, and higher small-signal and power bandwidth than conventional operational amplifiers such as the 1458. These characteristics make the device relevant to audio preamplification, filtering, signal conditioning, buffering, current sensing, analog measurement, and precision control. Exact input-offset voltage, input-bias current, slew rate, supply-current, output-current, and noise-density values are not present in the supplied source records and therefore remain data-needed rather than inferred. The NE5532DR2G uses a 20 V maximum supply classification in the verified GlobalSpec record and is identified as a dual operational amplifier in a SOIC package. Its internally compensated architecture is suited to conventional negative-feedback loops, but the actual usable bandwidth still depends on closed-loop gain, load, output amplitude, supply voltage, and PCB layout. Designers should avoid driving capacitive loads directly unless stability has been verified at the intended frequency. Typical uses include stereo audio input stages, active filters, low-level sensor amplification, analog control loops, and precision signal-conditioning blocks. The dual format can reduce package count in stereo or differential circuits, but both channels share the same supply pins and common ground. Decoupling and grounding remain as important as nominal noise specifications because supply coupling and ground impedance can degrade otherwise quiet measurements. For PCB implementation, place the bypass capacitor close to the supply pins and preserve a short, low-impedance return path. Decoupling capacitance and voltage rating must be selected from the complete circuit requirements because the supplied records do not state a manufacturer-recommended value. Stable feedback components and suitable source and sink loads are equally important when using the amplifier outside the manufacturer datasheet's exact test conditions. This page consolidates the verified distributor and source-page information, separates confirmed data from missing specifications, and adds engineering-focused application and design guidance. Distributor pricing and stock can change independently of the device, so the listed LCSC price is identified as a point-in-time commercial reference rather than a guaranteed quotation.
NE5532DRG4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments NE5532DRG4 is a dual, general-purpose operational amplifier with a 30 V power-supply rating, 10 MHz gain-bandwidth product, and 5 nV/√Hz typical input-noise voltage at 1 kHz, packaged in an 8-SOIC. It combines low noise, high slew rate, and substantial output-drive capability for audio signal paths. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its two inputs. Within the broader semiconductor hierarchy, this audio operational amplifier belongs to amplifier ICs and supports precision gain, buffering, active filtering, and low-distortion signal conditioning. The NE5532 contains two independent amplifiers while sharing one IC package and supply rails. Verified headline characteristics include a 9 V/µs slew rate, 10 MHz typical unity-gain bandwidth, and 100 dB typical common-mode rejection. Its 5 nV/√Hz typical input-noise density at 1 kHz makes it especially useful when amplifier noise would otherwise limit audio or instrumentation performance. Input-protection diodes and output short-circuit protection support practical general-purpose use. The NE5532 operates from ±5 V to ±18 V according to the cited product information, with a maximum total supply voltage of 30 V. It is intended for audio applications but can also implement microphone preamplifiers, active crossovers, line-level stages, filters, buffers, and low-frequency measurement circuits. The dual configuration reduces package count when two gain stages are required. For stable operation with a minimal external network, place the manufacturer-recommended bypass capacitors close to the supply pins and route traces away from noisy power and digital signals. Input and output impedance, load capability, output swing, distortion, and common-mode headroom determine the usable bandwidth. Do not assume the 10 MHz small-signal bandwidth remains available at every gain, voltage, and load condition. NE5532DRG4 is supplied in tape-and-reel packaging for automated assembly. This page combines verified distributor information, the Texas Instruments product description, same-package substitution guidance, and practical design notes to support sourcing and engineering selection without implying that merely similar amplifiers are automatically drop-in replacements. A pin-to-pin alternative must match the dual 8-SOIC footprint and pin functions as well as the voltage, bandwidth, noise, slew-rate, and drive requirements. Circuit-level substitution should also verify supply rails, gain configuration, output loading, distortion, stability, and intended audio performance. The comparisons below distinguish verified facts from parameters that still require manufacturer-specific confirmation.