Ürünler (44.000+)

TAS5186DDV - 6-Channel 210W Class D Power Stage | TI
TAS5186DDV

TAS5186DDV - 6-Channel 210W Class D Power Stage | TI

The Texas Instruments TAS5186DDV is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply. A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection. The TAS5186DDV provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output. Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design. Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits. Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions. This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.

RFQ İletişim
TAS5261DKD - 315W Mono Class D Amplifier | Texas Instruments
TAS5261DKD

TAS5261DKD - 315W Mono Class D Amplifier | Texas Instruments

The Texas Instruments TAS5261DKD is a 315 W mono bridge-tied-load Class D digital amplifier power stage packaged in a 36-pin HSSOP. It is designed to drive 4- to 8-ohm speakers with low harmonic distortion, and its digital input architecture requires a simple passive demodulation filter to produce high-quality, high-efficiency audio amplification. A Class D amplifier is a switching audio power stage whose output switches between the supply rails to amplify a pulse-width-modulated signal. After passive low-pass demodulation, this approach can provide high output power with lower power loss than a conventional linear audio amplifier. The TAS5261DKD belongs to the digital amplifier power-stage hierarchy, where an external input-processing stage generates the required modulation signal and the integrated power stage supplies current to the speaker load. The TAS5261DKD provides one mono amplification channel, supports 4- to 8-ohm speakers, and is identified as a 315 W mono BTL digital amplifier power stage. The manufacturer documentation also describes the device as a 400 W mono Class D amplifier, while the product-page description identifies a 315 W configuration. Its listed operating supply range is 10.8 V to 13.2 V. Digital inputs, short-circuit protection, and thermal protection are listed among the device features. The implementation uses a passive demodulation filter between the switching output and the speaker rather than an analog audio input stage. This architecture supports efficient amplification at relatively high output power, but the filter must be selected and laid out correctly because its response determines the recovered audio bandwidth, attenuation of carrier-related artifacts, and speaker-load stability. Typical uses include powered speakers, subwoofer amplifiers, professional audio equipment, consumer audio systems, and other mono loudspeaker applications operating from a 12 V-class supply. A bridge-tied-load configuration uses both output terminals to drive the speaker differentially, so the speaker remains connected between the two outputs rather than from one output to ground. PCB design should prioritize short power-stage connections, adequate thermal copper, a continuous supply path, careful grounding, and a stable reference return. The passive demodulation network should be placed close to the power-stage output, and its component values must follow the manufacturer reference design. Adequate copper area is important because Class D output current and supply transients can create losses, voltage drops, and EMI coupling even when the amplifier operates efficiently. This page combines the identified electrical ratings, package characteristics, application guidance, and manufacturer documentation links for engineering evaluation. It also distinguishes verified product facts from unspecified details so designers can consult the pin-description table, reference schematic, thermal guidance, and power calculations before committing a TAS5261DKD design to production.

RFQ İletişim
TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments
TAS5261DKDR

TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments

The Texas Instruments TAS5261DKDR is a 315 W mono bridged-load-tie class D digital power stage packaged in a 36-terminal HSSOP. It is designed for high-efficiency audio amplification where a compact solution must deliver substantial continuous output power to a low-impedance loudspeaker. The device accepts digital audio data and operates as a mono class D output stage, supporting compact consumer and professional audio systems. A class D power stage is a switching amplifier topology that controls current through the speaker output at high frequency. Compared with a linear audio amplifier, the switching approach reduces the power dissipated in the output devices and enables high output power with smaller magnetic components. In the wider power-management hierarchy, the TAS5261 belongs to the class D amplifier family, which falls under audio amplifier ICs and, more broadly, power management semiconductors. Key characteristics include 315 W rated mono output power, a single-channel class D architecture, a 36-HSSOP package, and a bridged-load-tie speaker configuration. The HSSOP package uses a gull-wing surface-mount form factor and exposes a thermal pad for heat removal when the device is mounted according to the manufacturer's recommended land pattern. Its operating voltage, output-stage limits, thermal characteristics, and signal-interface timing should be confirmed against the specific version of the manufacturer datasheet before layout release. Typical implementations include powered speakers, compact home-theater enclosures, soundbars, multimedia speaker systems, subwoofer amplifier modules, and industrial audio products driven by an external audio processor. Because the device is a power stage rather than a complete codec-equipped amplifier, upstream circuitry must supply the required digital audio stream and control signals. A properly designed LC output filter is required to remove high-frequency switching energy before the loudspeaker. Layout is the dominant design consideration. Place the input, control, power, and output-network connections according to the datasheet reference layout, minimize loop area in high-current switching paths, and provide substantial copper area for thermal dissipation. Verify junction temperature at worst-case supply voltage, output power, and ambient temperature rather than relying on nominal board temperature alone. This page adds application-focused implementation guidance, pin-compatible sourcing information, and a structured comparison of the documented operating characteristics. Use the manufacturer datasheet and reference layout as the controlling documents for production design, EMC tuning, and thermal validation.

RFQ İletişim
TAS5342DDV - 100W Stereo Class D Power Stage | Texas Instruments
TAS5342DDV

TAS5342DDV - 100W Stereo Class D Power Stage | Texas Instruments

Texas Instruments TAS5342DDV is a 100-W stereo digital amplifier power stage designed for Class D audio systems, supplied in a 44-HTSSOP package. The device is intended for stereo or bridge-tied-load (BTL) configurations and supports speaker loads up to 8 ohm. Its integrated digital power-stage design is intended to provide high output power with low harmonic distortion, low integrated noise, and low idle current for audio receivers, powered speakers, soundbars, and other compact audio systems. A digital Class D power stage is a semiconductor amplifier category that converts a digital audio signal into a high-current switching waveform and then reconstructs the audio output through the speaker and output filtering network. Within the power-management hierarchy, the TAS5342DDV combines an audio amplifier, power conversion function, output-driver capability, and integrated fault protection in one power-management IC. It is commonly paired with an audio DSP or digital-audio interface that generates the required PWM signals. The TI product page identifies the TAS5342 as a high-performance integrated stereo digital amplifier power stage capable of driving a bridge-tied load at up to 100 W per channel. The listed operating power-supply range is 0 V to 34 V, with a typical supply range of 10.8 V to 13.2 V. The device supports differential input and differential output arrangements, which help reject common-mode noise and allow flexible speaker-routing configurations. The integrated protection system is a major functional feature. Texas Instruments describes protection against multiple fault conditions, including output-related faults that could otherwise damage the power stage or connected speaker network. The 44-HTSSOP package provides a high pin count for power connections, signal routing, control functions, and thermal management. Because power amplifiers dissipate energy in their output stages, correct copper area, thermal-pad layout, heat spreading, and enclosure ventilation are essential in practical designs. Typical applications include powered stereo speakers, home-theater receivers, compact soundbars, multimedia speakers, and other consumer audio equipment. The 100-W-per-channel capability is useful when the loudspeaker load is nominally 8 ohm and the amplifier is operated within the manufacturer-recommended supply and thermal limits. The differential output structure also makes the device suitable for BTL speaker connections, where each channel drives the speaker differentially. For implementation, follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning the 44-HTSSOP land pattern. Keep the power-stage supply and output-current paths compact, provide adequate input and output filtering, and confirm that the exposed thermal pad is connected to the intended ground and copper area. The amplifier should not be selected solely by its headline wattage; speaker impedance, supply voltage, thermal dissipation, modulation scheme, and output-filter requirements determine the practical result. This page summarizes the key electrical, packaging, protection, and application characteristics of the TAS5342DDV and organizes them for faster design review. It also identifies the limits of directly replacing a power-stage IC: a valid drop-in candidate must match the package, pinout, supply assumptions, output architecture, and thermal requirements rather than merely share a similar wattage rating.

RFQ İletişim
TAS5352DDV 125W Stereo Class-D Power Stage | Texas Instruments
TAS5352DDV

TAS5352DDV 125W Stereo Class-D Power Stage | Texas Instruments

The Texas Instruments TAS5352DDV is an integrated stereo digital Class-D amplifier power stage designed to drive a 4 ohm bridge-tied load at up to 125 W per channel. It operates from a 10.8 V to 13.2 V supply and is packaged in a 44-pin HTSSOP with an exposed thermal pad. The device provides a high-efficiency speaker-drive solution with low harmonic distortion, low integrated noise, and low idle current. A digital Class-D audio power amplifier is a power-management IC that switches its output stage rapidly between voltage states to reproduce an audio waveform. Its efficiency is generally higher than that of a conventional linear amplifier because the switching stage dissipates less power when driving a speaker load. Bridge-tied-load operation applies the audio waveform across the two speaker terminals, increasing the available output voltage and power without requiring a physical ground connection at the speaker. The TAS5352DDV integrates a stereo output stage and a complete on-chip protection system. Its principal output rating is 125 W per channel into a 4 ohm BTL load, while its listed operating supply range is 10.8 V to 13.2 V. The device is specified for low harmonic distortion and low integrated noise, making it suitable for compact high-power audio systems. Its low idle current can also reduce standby dissipation when the associated system power architecture requires low quiescent consumption. TAS5352 is positioned as a power stage rather than a complete audio input amplifier. A practical system therefore needs a source capable of supplying the appropriate input signal, control or codec circuitry where required, output filtering, and a correctly designed speaker network. The manufacturer documents internal pull-up resistors to 3.3 V on the SD and OTW outputs; external pull-up resistors can provide 5 V logic level compliance where that interface voltage is required. Typical uses include powered speakers, compact home-theater systems, professional audio equipment, soundbars, subwoofer power modules, and other high-efficiency speaker-drive products. A 10.8 V to 13.2 V supply is particularly compatible with systems organized around a 12 V rail, although final rail limits, startup behavior, current demand, and protection requirements must be evaluated against the complete amplifier design. Thermal design is central to achieving the 125 W per-channel rating. The exposed-pad HTSSOP construction requires a low-impedance PCB thermal path, adequate copper area, and suitable airflow or enclosure heat transfer. Decoupling capacitors must be placed close to the supply and ground pins, and output-filter layouts must keep high-current switching paths compact. Speaker wiring, connectors, and load selection must also support the intended channel power. This page consolidates the verified device identity, package information, operating limits, interface details, and drop-in assessment into an engineering-focused reference. It also distinguishes documented functional similarity from true pin-to-pin equivalence, helping designers avoid treating a related part as an automatic replacement without completing a footprint, signal, control, and thermal review.

RFQ İletişim
TAS5504APAG - 4-Channel Digital Audio PWM Processor | Texas Instruments
TAS5504APAG

TAS5504APAG - 4-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5504APAG is a four-channel digital audio PWM processor packaged in a 64-pin TQFP measuring 10 mm by 10 mm. It is designed to generate four independent Class-D audio output channels from digital audio data, combining digital signal processing, PWM modulation, and integrated audio output control in one device. A digital audio PWM processor is a specialized interface and signal-processing IC that converts digital audio samples into controlled PWM drive signals for power stages. In the broader power-management and audio-system hierarchy, it connects a digital audio source, such as a USB, network, or optical audio interface, to the PWM inputs of an external Class-D amplifier. The TAS5504A family therefore occupies the signal-generation stage between digital audio data and the analog power-amplifier output stage. The device's defining product features are its four-channel architecture, 64-pin TQFP package, and 10 mm by 10 mm body size. The manufacturer categorizes it as a digital audio PWM processor and as an audio modulator. Its four-channel structure allows one processor to manage multiple audio zones or paired amplifier channels while reducing the number of discrete control and modulation functions required in a multi-channel audio system. As a digital signal-processing and modulation device, the TAS5504A accepts digital audio information and applies embedded processing functions before producing PWM control waveforms for downstream power stages. This architecture allows audio-system design decisions to be centralized in the processor rather than distributed across separate digital-to-analog conversion, analog filtering, and modulation blocks. Exact signal formats, sampling rates, filter characteristics, clock requirements, and electrical limits must be confirmed in the manufacturer datasheet for the specific power-amplifier design. Typical applications include multi-channel home-theater and powered-speaker systems, active crossover networks, soundbars, professional audio equipment, and compact consumer-audio products. Its four-channel organization is particularly useful when two stereo amplifier channels must share one digital-audio source or when several independently controlled amplifier zones require synchronized digital modulation. The processor should be paired with an external Class-D output stage because it generates PWM control signals rather than directly delivering high-power speaker current. Layout is critical because digital clocking, PWM outputs, analog supply rails, and ground returns meet on a dense 64-pin surface-mount package. Keep high-current amplifier paths physically separate from the TAS5504APAG, use the manufacturer-recommended power and ground-plane arrangements, and provide local bypassing at the device supply pins. A solid return path and careful isolation of switching-node energy reduce the risk of audible artifacts or modulation instability. This page organizes the manufacturer device information, package characteristics, sourcing questions, application guidance, and confirmed same-footprint alternatives into a practical engineering reference. It also separates documented product facts from parameters that still require verification, helping designers decide when the TAS5504APAG is appropriate and what must be checked before committing a four-channel Class-D audio design to production.

RFQ İletişim
TAS5504PAG - 4-Channel Digital Audio PWM Processor | Texas Instruments
TAS5504PAG

TAS5504PAG - 4-Channel Digital Audio PWM Processor | Texas Instruments

Texas Instruments TAS5504PAG is a four-channel digital audio PWM processor with I2C and I2S interfaces, supplied in a 64-pin TQFP package measuring 10 mm by 10 mm. Its verified operating supply range is 3 V to 3.6 V, and the supported audio sampling-rate range is 32 kHz to 192 kHz. The processor is designed to accept digital audio data, perform configurable digital signal processing, and generate modulated outputs for downstream power stages. A digital audio PWM processor is a specialized signal-processing IC used to transform digital audio streams into control signals for power amplifiers and other audio output stages. Within the broader hierarchy, it belongs to digital signal processing, audio processing, and power-management interface components. Its digital architecture separates audio data conversion from the final analog power-amplifier stage, allowing digital controls and processing to operate before the signal reaches the power circuitry. The TAS5504PAG provides four independent audio channels and supports digital interfaces described in the verified distributor data as I2C and I2S. The I2S interface is used for serial audio data transfer, while I2C supports device configuration. The 32 kHz to 192 kHz range covers standard consumer-audio rates through high-resolution audio, making the processor applicable to multichannel audio systems that need centralized digital control. Its 64-TQFP package provides 64 connection positions for digital audio data, control, clocking, power, ground, and configuration signals. The 10 mm by 10 mm package is larger than a compact QFN but offers ample routing access for the numerous interfaces needed by a four-channel processor. A multilayer PCB with a low-impedance ground plane and short, terminated clock and data routes is appropriate when signal integrity is important. Typical applications include digital active speakers, multichannel audio amplifiers, home-theater amplification, soundbars, and compact consumer-audio systems. The processor can receive digital audio from a source or host processor and provide modulation data for a multi-channel amplifier stage. Compared with an analog-input-only controller, a digital architecture can preserve the source signal in digital form until power amplification. The primary design consideration is confirming that the host interface, audio data format, sample rate, channel mapping, and amplifier topology match the system requirements. The 3 V to 3.6 V supply range also requires regulators with suitable headroom and low-noise behavior. Decoupling capacitors should be positioned close to the supply and ground pins, while clock and I2S traces should be routed away from switching nodes. This page consolidates verified distributor specifications, current pricing references, same-package replacement candidates, and practical implementation guidance. It also distinguishes verified drop-in candidates from higher-channel-count devices that are not true pin-compatible replacements, helping engineers avoid an unqualified board-level substitution.

RFQ İletişim
TAS5504PAGR - 4-Channel Digital Audio PWM Processor | Texas Instruments (Tape & Reel)
TAS5504PAGR

TAS5504PAGR - 4-Channel Digital Audio PWM Processor | Texas Instruments (Tape & Reel)

Texas Instruments TAS5504PAGR is a four-channel digital audio PWM processor with I2C and I2S interfaces, supplied in a 64-pin TQFP package measuring 10 mm by 10 mm. Its verified operating supply range is 3 V to 3.6 V, and the supported audio sampling-rate range is 32 kHz to 192 kHz. The processor is designed to accept digital audio data, perform configurable digital signal processing, and generate modulated outputs for downstream power stages. A digital audio PWM processor is a specialized signal-processing IC used to transform digital audio streams into control signals for power amplifiers and other audio output stages. Within the broader hierarchy, it belongs to digital signal processing, audio processing, and power-management interface components. Its digital architecture separates audio data conversion from the final analog power-amplifier stage, allowing digital controls and processing to operate before the signal reaches the power circuitry. The TAS5504PAGR provides four independent audio channels and supports digital interfaces described in the verified distributor data as I2C and I2S. The I2S interface is used for serial audio data transfer, while I2C supports device configuration. The 32 kHz to 192 kHz range covers standard consumer-audio rates through high-resolution audio, making the processor applicable to multichannel audio systems that need centralized digital control. Its 64-TQFP package provides 64 connection positions for digital audio data, control, clocking, power, ground, and configuration signals. The 10 mm by 10 mm package is larger than a compact QFN but offers ample routing access for the numerous interfaces needed by a four-channel processor. A multilayer PCB with a low-impedance ground plane and short, terminated clock and data routes is appropriate when signal integrity is important. Typical applications include digital active speakers, multichannel audio amplifiers, home-theater amplification, soundbars, and compact consumer-audio systems. The processor can receive digital audio from a source or host processor and provide modulation data for a multi-channel amplifier stage. Compared with an analog-input-only controller, a digital architecture can preserve the source signal in digital form until power amplification. The primary design consideration is confirming that the host interface, audio data format, sample rate, channel mapping, and amplifier topology match the system requirements. The 3 V to 3.6 V supply range also requires regulators with suitable headroom and low-noise behavior. Decoupling capacitors should be positioned close to the supply and ground pins, while clock and I2S traces should be routed away from switching nodes. This page consolidates verified distributor specifications, current pricing references, same-package replacement candidates, and practical implementation guidance. It also distinguishes verified drop-in candidates from higher-channel-count devices that are not true pin-compatible replacements, helping engineers avoid an unqualified board-level substitution.

RFQ İletişim
TAS5508APAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5508APAG

TAS5508APAG - 8-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5508APAG is an 8-channel digital audio PWM processor for high-fidelity multichannel audio systems, housed in a 64-pin TQFP package measuring 10 x 10 mm. It supports sample rates from 32 kHz to 192 kHz and is categorized as a digital audio PWM processor and audio modulator. The device interfaces digital audio signals with external amplifier stages, providing centralized control for multichannel Class-D audio architectures. A digital audio PWM processor is a specialized interface IC that converts or prepares digital audio data for power-amplifier stages. It sits between an audio DSP, codec, or source controller and the power-amplifier output network. Within the signal chain, the hierarchy is digital audio processor, audio interface IC, PWM modulator, and power-management semiconductor. Integrating eight channels in one package reduces the number of separate control devices required for surround-sound and multichannel installations. The TAS5508APAG combines an 8-channel architecture with support for audio sample rates up to 192 kHz. This makes it appropriate for high-resolution consumer and professional audio systems operating at standard CD, DVD, multichannel cinema, and higher-rate digital audio sampling frequencies. Its 64-TQFP package provides a substantial number of external connections for digital audio data, clock signals, control signals, and power connections. The processor integrates digital control for eight audio output channels and is designed to operate with compatible digital signal processors and audio power stages. Automatic control configuration in response to clock and data conditions is associated with the TAS5508 family, helping the device adapt to changing digital-audio operating states. System designers should use the manufacturer pin-description table and reference circuit when assigning the complete 64-pin land pattern. Typical uses include 5.1-channel and 7.1-channel home-theater systems, professional digital mixing consoles, active speaker networks, automotive audio systems, and powered multiway speakers. The eight-channel architecture is particularly useful where a single DSP must distribute synchronized control across multiple Class-D amplifier channels. The device is also suitable for high-resolution installations operating with audio sample rates between 32 kHz and 192 kHz. Layout is critical because high-channel-count digital audio processors combine clock-sensitive signals with power-supply connections in a 10 x 10 mm TQFP footprint. Keep clock and data traces short, route them away from switching-node and power-converter traces, and place decoupling capacitors close to their associated supply pins. Follow the manufacturer’s recommended component values and pin-specific connection instructions to avoid signal-integrity problems. This page consolidates the device identity, package information, supported sample-rate range, sourcing information, compatible family references, and practical implementation guidance into one engineering-focused reference. It helps engineers separate confirmed product characteristics from details that require direct verification against the current Texas Instruments datasheet.

RFQ İletişim
TAS5508BPAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5508BPAG

TAS5508BPAG - 8-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5508BPAG is an 8-channel digital audio PWM processor with I2C and serial digital-audio interfaces, designed for multichannel audio output systems. It operates from a 3 V to 3.6 V supply and is packaged in a 64-pin TQFP measuring 10 mm by 10 mm. Its eight-channel PWM architecture consolidates multiple audio output functions into one dedicated device while maintaining compatibility with conventional digital audio signal processors. An audio PWM processor is a specialized type of digital signal processor that accepts digital audio data and generates the pulse-width-modulated drive signals required by multi-channel Class-D audio output stages. Within the broader semiconductor hierarchy, it belongs to the digital signal processing family, then to audio DSPs, and ultimately to audio interface and power-management systems. The TAS5508BPAG is intended for systems that require more channels than a basic stereo audio interface can provide. The principal identified features are eight PWM output channels, a 3 V to 3.6 V operating supply range, I2C control support, a serial digital-audio interface, and a compact 64-pin TQFP package. These characteristics make the device applicable to home-theater receivers, active speakers, multichannel amplifiers, sound bars, and other systems requiring several synchronized digital audio output channels. The I2C interface supports configuration from a system controller, while the serial interface connects the processor to an upstream audio source. The integrated eight-channel PWM architecture reduces the number of separate digital audio output functions required in a multichannel design. Configuration is managed through digital control interfaces rather than discrete analog programming networks. Because the processor operates from a supply range extending down to 3 V, it can be paired with 3.3 V system logic. Its 10 mm by 10 mm TQFP package provides a standardized surface-mount footprint but requires careful thermal and layout planning during implementation. Typical audio-system uses include powered speakers, surround-sound receivers, active speaker arrays, multi-zone amplifiers, and digital mixing equipment. In each case, the processor occupies the digital control and PWM-generation stage before power amplification and speaker output. System designers must select an external power stage compatible with the device's voltage, current, timing, and output requirements. Use the manufacturer datasheet for the complete pin description, electrical limits, interface timing, recommended application circuit, and thermal information. A common implementation concern is ensuring that digital data, control signals, ground returns, and power-supply connections follow the specified layout because switching-edge energy from an audio system can affect signal integrity if routing is not controlled. This page combines the exact manufacturer and distributor listing details with application guidance, interface considerations, and verified same-package replacement information. It is intended to help engineers identify the correct device, locate its documentation, and assess whether a candidate replacement preserves the 64-pin TQFP footprint.

RFQ İletişim
TAS5508CPAG - 8-Channel PWM Processor | Texas Instruments
TAS5508CPAG

TAS5508CPAG - 8-Channel PWM Processor | Texas Instruments

Texas Instruments TAS5508CPAG is an 8-channel digital pulse-width modulation processor designed for advanced audio power amplification, with automatic control configuration in response to clock-rate, data-rate, and idle-state changes. The device is packaged in a 64-pin TQFP (PAG) package measuring 10 mm by 10 mm. A digital PWM processor is an audio-control and signal-generation IC that accepts digital audio information from an audio DSP and converts it into coordinated PWM outputs. Within the product hierarchy, it belongs to the digital signal processing and interface-controller family of semiconductors, where it bridges the digital audio source and a downstream power-amplifier or Class-D output stage. Its integration can reduce the number of separate timing, control, and output-routing functions required by a multichannel audio system. The headline characteristics of the TAS5508CPAG are eight processing channels, digital PWM operation, and a 64-pin TQFP package. Automatic adjustment of control configurations when clock or data rates change allows the processor to respond to changing source conditions without requiring the host system to reconfigure every output manually. Its idle-condition handling is also intended to simplify power-state behavior in audio equipment where channel activity changes frequently. The processor is designed to interface with most audio digital signal processors, creating a conventional separation between source decoding or sound processing and the final PWM control stage. That architecture is useful in multichannel home theater, powered speakers, sound bars, automotive audio, and professional listening equipment where multiple channels must remain synchronized while the input format, sample rate, or activity state changes. The integrated control approach also simplifies board partitioning compared with a design built from separate PWM-generation devices. The 64-pin PAG package provides the pin count needed for eight-channel operation, control signals, clocking, data interfaces, power connections, and ground routing. A 10 mm by 10 mm TQFP is surface-mountable and compatible with conventional PCB assembly and inspection processes. Designers should follow the manufacturer pin-description table and recommended application schematic when assigning tracks because clock, serial-data, and PWM routing must preserve timing and signal integrity. Use the TAS5508CPAG when a design needs an integrated eight-channel digital PWM control stage driven by an audio DSP. Validate clock topology, data-format compatibility, idle-state behavior, output configuration, and power sequencing against the manufacturer datasheet before layout release. Proper grounding and controlled clock routing are essential for repeatable multichannel performance and low conversion-related interference. This page organizes the TAS5508CPAG technical facts, sourcing routes, drop-in comparison limits, and practical design considerations into one engineering reference. It also distinguishes verified device capabilities from design parameters that must be confirmed in the manufacturer datasheet and application schematic.

RFQ İletişim
TAS5508PAG - 8-Channel Digital Audio PWM Processor | TI
TAS5508PAG

TAS5508PAG - 8-Channel Digital Audio PWM Processor | TI

Texas Instruments TAS5508PAG is an eight-channel digital audio PWM processor packaged in a 64-pin TQFP. It is designed to provide integrated digital-audio modulation for systems requiring eight simultaneous processing channels, precise timing, and coordinated signal generation. The manufacturer identifies the device as a PWM processor with eight digital channels, positioning it between general-purpose digital signal processing and a dedicated audio-class conversion controller. A digital audio PWM processor converts digital audio information into controlled pulse-width-modulated outputs for downstream power stages, amplifiers, or associated signal-chain functions. This device category belongs to the broader hierarchy of digital audio IC, audio signal processor, semiconductor, and embedded audio system. Its eight-channel architecture is intended to reduce the number of separate digital-to-audio modulation functions required in multi-channel amplification and audio-routing equipment. The TAS5508PAG combines eight-channel PWM processing with high system integration in its 64-pin TQFP package. The 64-pin package provides the external connections needed for multi-channel control, data exchange, configuration, clocking, and power connections. According to the manufacturer datasheet, the device supports eight simultaneous digital-audio channels, while the verified product descriptions consistently identify the TAS5508PAG as an eight-channel digital audio PWM processor. From a design perspective, channel synchronization and digital timing are central considerations because the processor coordinates multiple PWM outputs. Designers should preserve the data, clock, reset, control, and power topology shown in the manufacturer reference design and observe the recommended external-component values. Accurate layout, clean reference connections, and controlled clock routing help maintain consistent behavior across all eight channels and reduce sensitivity to noise or timing skew. Typical end uses include multichannel class-D audio amplification, powered speakers, home-theater equipment, active loudspeaker systems, and other multichannel audio products. In these systems, the TAS5508PAG can manage the digital audio modulation stage while external amplifier and output stages perform the required power conversion. The exact supported digital interface, sample-rate range, clock requirements, and channel operating modes should be confirmed from the manufacturer datasheet before schematic release. The primary design trade-off is integration versus board area: one 64-pin TQFP consolidates eight-channel processing but requires careful pin assignment, multilayer routing, and power-plane planning. Use the manufacturer pin-description table when assigning tracks, and use the datasheet evaluation-circuit and layout guidance when deriving a production PCB. This page summarizes the verified device identity and provides practical application, comparison, and sourcing guidance while clearly separating confirmed facts from parameters requiring datasheet confirmation.

RFQ İletişim
TAS5508PAGR - 8-Channel Digital Audio PWM Processor | TI (Tape & Reel)
TAS5508PAGR

TAS5508PAGR - 8-Channel Digital Audio PWM Processor | TI (Tape & Reel)

Texas Instruments TAS5508PAGR is an eight-channel digital audio PWM processor packaged in a 64-pin TQFP. It is designed to provide integrated digital-audio modulation for systems requiring eight simultaneous processing channels, precise timing, and coordinated signal generation. The manufacturer identifies the device as a PWM processor with eight digital channels, positioning it between general-purpose digital signal processing and a dedicated audio-class conversion controller. A digital audio PWM processor converts digital audio information into controlled pulse-width-modulated outputs for downstream power stages, amplifiers, or associated signal-chain functions. This device category belongs to the broader hierarchy of digital audio IC, audio signal processor, semiconductor, and embedded audio system. Its eight-channel architecture is intended to reduce the number of separate digital-to-audio modulation functions required in multi-channel amplification and audio-routing equipment. The TAS5508PAGR combines eight-channel PWM processing with high system integration in its 64-pin TQFP package. The 64-pin package provides the external connections needed for multi-channel control, data exchange, configuration, clocking, and power connections. According to the manufacturer datasheet, the device supports eight simultaneous digital-audio channels, while the verified product descriptions consistently identify the TAS5508PAGR as an eight-channel digital audio PWM processor. From a design perspective, channel synchronization and digital timing are central considerations because the processor coordinates multiple PWM outputs. Designers should preserve the data, clock, reset, control, and power topology shown in the manufacturer reference design and observe the recommended external-component values. Accurate layout, clean reference connections, and controlled clock routing help maintain consistent behavior across all eight channels and reduce sensitivity to noise or timing skew. Typical end uses include multichannel class-D audio amplification, powered speakers, home-theater equipment, active loudspeaker systems, and other multichannel audio products. In these systems, the TAS5508PAGR can manage the digital audio modulation stage while external amplifier and output stages perform the required power conversion. The exact supported digital interface, sample-rate range, clock requirements, and channel operating modes should be confirmed from the manufacturer datasheet before schematic release. The primary design trade-off is integration versus board area: one 64-pin TQFP consolidates eight-channel processing but requires careful pin assignment, multilayer routing, and power-plane planning. Use the manufacturer pin-description table when assigning tracks, and use the datasheet evaluation-circuit and layout guidance when deriving a production PCB. This page summarizes the verified device identity and provides practical application, comparison, and sourcing guidance while clearly separating confirmed facts from parameters requiring datasheet confirmation.

RFQ İletişim
TAS5518CPAG - 8-Channel Digital Audio PWM Processor | TI
TAS5518CPAG

TAS5518CPAG - 8-Channel Digital Audio PWM Processor | TI

The Texas Instruments TAS5518CPAG is an 8-channel digital audio PWM processor packaged in a 64-pin TQFP measuring 10 mm by 10 mm. It is designed to process digital audio information and generate PWM-based output signals for multichannel audio systems. The device combines eight audio channels with a dedicated digital signal-processing function in a single surface-mount package, making it a central component in advanced audio system architectures. A digital audio PWM processor is a specialized type of digital signal processor. It receives digital audio data, applies digital signal-processing operations, and produces PWM control signals that can drive external power stages or associated audio circuitry. Within the broader semiconductor hierarchy, it belongs to digital signal processors, audio processing ICs, and ultimately power management and signal-chain semiconductor solutions. Integrating multiple channels can reduce the number of separate processing devices required in a multichannel amplifier design. The TAS5518 family’s primary headline specifications are eight processed audio channels, digital audio signal processing, and a compact 64-pin TQFP package. The package provides a practical surface-mount footprint for multichannel consumer and professional audio equipment. Its pin count offers the interconnect capacity required for digital data, clocking, control, and analog or power-stage-related functions encountered in a complete audio processor design. Because the device performs processing before power-stage conversion, the implementation of the surrounding system determines the final audio performance. Clock architecture, supported digital audio format, control interface, PWM output behavior, supply requirements, and external power-stage selection are essential parts of the design. The 8-channel structure is particularly useful when a product requires coordinated amplification or level management across several speakers, zones, or physical channels. Typical uses include multichannel home-theater amplification, powered speakers, professional audio consoles, digital active loudspeakers, soundbar platforms, and automotive entertainment systems. In these applications, the processor can centralize digital audio routing and channel control while external transistors or integrated amplifiers translate the generated PWM signals into analog power capable of driving loudspeakers. PCB planning should place power and ground connections to minimize return-path resistance, keep sensitive clock and data routing away from high-current switching nodes, and follow the manufacturer reference layout for decoupling and signal routing. Decoupling capacitors should be placed directly beside their associated supply pins, while external switching devices require careful thermal and layout planning to minimize switching noise reaching the audio processor. This product page consolidates the verified device identity, package information, sourcing workflow, application guidance, and qualification notes into a design-focused reference. It also distinguishes confirmed drop-in candidates from devices that require additional engineering review, helping engineers evaluate replacement choices without assuming that every similarly packaged audio IC is electrically interchangeable.

RFQ İletişim
TAS5518PAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5518PAG

TAS5518PAG - 8-Channel Digital Audio PWM Processor | Texas Instruments

Texas Instruments TAS5518PAG is an 8-channel digital audio PWM processor with a typical system dynamic range of 110 dB and a 64-pin TQFP (PAG) package. The device integrates digital audio processing, power-supply volume control, and multi-channel PWM output functionality into one audio-focused system IC. It is intended for designs that require coordinated audio-channel control without implementing eight separate digital input channels and PWM output stages. A digital audio PWM processor is a mixed-signal audio IC that accepts digital audio information and controls PWM-based amplifier stages. Within the audio signal-chain hierarchy, it sits between a digital audio source and a power-amplifier or speaker-driving circuit. Unlike a conventional analog power amplifier, the TAS5518PAG manages digital modulation data, volume-related functions, and channel integration, allowing the connected amplifier stage to reproduce the intended audio signal. The principal system benefit is high integration. According to the Texas Instruments product information, the TAS5518PAG supports eight digital audio channels in one device. A well-designed system can achieve typical dynamic range of 110 dB, while the power supply volume control feature provides up to 24 dB of additional dynamic range at normal listening levels. This combination can reduce external control-component complexity and centralize audio-volume behavior across multiple channels. The TAS5518PAG also provides direct support for digital-audio signal processing before the PWM output stage. This architecture is appropriate for multichannel consumer-audio equipment where synchronized channel control and system-level volume management are more important than a conventional standalone analog output stage. Its 64-pin TQFP (PAG) package provides the pin count needed for multichannel digital interfaces, control signals, power connections, and multiple PWM outputs. Typical uses include powered speakers, soundbars, home-theater audio systems, active speakers, multichannel audio receivers, and compact consumer audio products. The device can serve as the central PWM processor in an eight-channel signal path when its digital interface, output arrangement, and power architecture align with the selected amplifier topology. Board-level implementation must account for clean power, grounded return paths, signal integrity, and thermal performance. Designers should verify the complete pin arrangement, recommended external components, interface timing, and power-supply requirements in the manufacturer datasheet before routing a new PCB. Because this orderable designation is marked as not recommended for new designs, new products should first evaluate TI's current alternate-part recommendations and confirm functional, firmware, and mechanical compatibility rather than assuming direct interchangeability. This page consolidates the device classification, verified package information, lifecycle position, candidate replacement information, and practical selection guidance. It also distinguishes confirmed drop-in information from broader functional alternatives, helping engineers make a defensible sourcing decision without treating similar audio processors as footprint-compatible substitutes.

RFQ İletişim
TAS5518PAGR - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5518PAGR

TAS5518PAGR - 8-Channel Digital Audio PWM Processor | Texas Instruments

Texas Instruments TAS5518PAGR is an eight-channel digital audio PWM processor with a typical system dynamic range of 110 dB, PSVC support for up to 24 dB of additional dynamic range, and a 64-pin TQFP package measuring 10 x 10 mm. It accepts digital audio data and generates PWM drive signals for eight Class-D amplifier channels. A digital audio PWM processor is a mixed-signal audio IC that combines digital control, modulation, and output-driver functions in one device. It sits between an audio source, such as a digital audio interface or decoder, and power-amplifier stages. The TAS5518 integrates channel volume control, modulation, and system-level audio management to reduce the number of external discrete components required by multichannel audio systems. Principal features include eight audio channels, a 110 dB typical dynamic range in a well-designed system, and a power supply volume control feature that can contribute up to 24 dB of additional dynamic range at normal listening levels. Its 3 V to 3.6 V operating supply range supports integration with common low-voltage digital audio platforms, while the 64-pin TQFP package provides adequate routing density for eight-channel outputs. The architecture is designed to preserve audio quality while concentrating channel-level processing and PWM generation on one IC. Digital command and control information can be used to configure the multichannel system, and the PSVC function provides additional headroom relative to a fixed system operating level. This makes the processor useful where channel imbalance, small-signal dynamic-range limitations, or the cost of multiple external control paths would otherwise constrain the design. Typical uses include powered speakers, sound bars, home-theater receivers, active speaker networks, automotive audio systems, and other consumer or professional products requiring multiple Class-D amplifier channels. A practical implementation must preserve clean digital and analog ground returns, decouple the supply close to the device, and route high-current PWM outputs as controlled-impedance signals rather than treating them as ordinary low-frequency logic nets. Careful PCB partitioning is essential because the device combines digital control with timing-sensitive PWM outputs. Keep communication traces away from output nodes, use the manufacturer-recommended power and ground layout, and provide adequate copper around exposed thermal and power-distribution structures. Confirm the external clock, serial interface, and reset implementation against the manufacturer datasheet before releasing the PCB. This product page combines the manufacturer device description, package and channel details, lifecycle information, drop-in replacement assessment, application guidance, and practical layout considerations. It is intended to help engineers evaluate the TAS5518PAGR for multichannel digital-audio architectures and compare it with identified same-family devices without obscuring package or feature differences.

RFQ İletişim
TAS5548DCA - 8-Channel 96kHz PWM Audio Processor | TI
TAS5548DCA

TAS5548DCA - 8-Channel 96kHz PWM Audio Processor | TI

The Texas Instruments TAS5548DCA is an 8-channel digital pulse-width-modulation audio processor with digital audio processing, an integrated asynchronous sample-rate converter, and a 96 kHz PWM output stage, housed in a 56-pin HTSSOP package. It combines eight-channel audio processing with integrated sample-rate conversion to support high-definition home-theater signal paths. An audio processor is a specialized interface IC that manages digital audio data between source devices and power-conversion stages. Within the broader hierarchy, the TAS5548DCA belongs to digital audio processing, audio system semiconductors, and power-management signal-chain components. Its PWM outputs provide a digital representation of audio waveforms for downstream amplification and speaker-drive circuitry. The device includes two asynchronous sample-rate-converter modules, with each module handling four channels. This arrangement allows the processor to support multichannel operation and aligns it with DTS-HD-compatible Blu-ray home-theater-in-a-box applications identified by Texas Instruments. The architecture also consolidates digital audio processing, sample-rate conversion, and eight-channel PWM modulation into one package. TAS5548DCA is controlled through an external I2C interface, enabling an embedded host or audio system controller to configure the processor and manage its operating state. Integrating digital control with multichannel PWM output reduces the number of separate functional blocks needed in compatible home-theater and powered-speaker systems while preserving a centralized digital signal path. Typical implementation areas include DTS-HD-compatible Blu-ray home-theater systems, multichannel powered speakers, digital active loudspeakers, home-theater processor boards, and other audio equipment requiring eight PWM channels. The 56-pin HTSSOP package is designed for surface-mount assembly, while the stated operating-temperature range is 0°C to +85°C. Layout planning should prioritize short, controlled connections among the digital-audio inputs, I2C control interface, ground network, supply rails, and PWM outputs. Because the device combines high-channel-count processing with a fine-pitch surface-mount package, careful decoupling and return-path design are essential for reliable signal transfer and thermal performance. This page combines the manufacturer product information with practical distinctions for evaluating the TAS5548DCA, including its 8-channel architecture, 96 kHz PWM operation, integrated ASRC, package format, application fit, and the documentation needed for PCB and firmware planning.

RFQ İletişim
TAS5548DCAR - 8-Channel 96kHz PWM Audio Processor | Texas Instruments
TAS5548DCAR

TAS5548DCAR - 8-Channel 96kHz PWM Audio Processor | Texas Instruments

The Texas Instruments TAS5548DCAR is an 8-channel HD-compatible digital audio processor with a 96kHz PWM modulator, digital audio processing, and integrated asynchronous sample-rate conversion, housed in a 56-HTSSOP package. It provides eight PWM output channels, two ASRC modules handling four channels each, and digital audio processing for home-theater and surround-sound systems. What is an audio processor with PWM output? It is a specialized digital audio IC that receives digital audio data, applies decoding, volume, mixing, or other processing functions, and generates pulse-width-modulated signals for downstream power stages. In the signal chain, the TAS5548DCAR sits between an HDMI or digital audio source and a class-D amplifier or speaker-driving interface. Its integration reduces the number of external digital signal-processing components required in a multichannel audio design. The TAS5548DCAR supports up to eight channels and is designed for DTS-HD specification Blu-ray HTiB applications. Its 96kHz PWM output architecture supports high-resolution audio signal generation, while the integrated ASRC allows the device to handle asynchronous sampling-rate conversion across two four-channel modules. The manufacturer identifies the device as an 8-channel digital PWM with digital audio processing and sample-rate conversion. The DCA package designation identifies the 56-HTSSOP package used by TAS5548DCAR. The exposed-pad construction is intended for surface-mount PCB assembly and provides a large thermal and electrical land beneath the device. Because this is a digital signal-processing IC rather than a power semiconductor, its SOA field is not applicable; thermal design instead focuses on package dissipation, exposed-pad layout, and copper spreading. Typical applications include Blu-ray home-theater systems, active speaker designs, HDMI audio processors, multichannel Class-D amplifier control, and digital sound-bar platforms. The device is particularly relevant where multiple digital audio channels must be converted into PWM outputs before amplification. Its main system trade-off is integration and channel density versus the need for careful PCB layout, suitable decoupling, and compatible downstream amplifier inputs. For PCB implementation, place the input, output, clock, and decoupling connections according to the manufacturer pin-description table and recommended layout guidance. Keep high-speed digital traces controlled, provide a continuous ground reference, and solder the exposed pad with adequate thermal-via density. Verify the external clock, I2C control interface, memory connections, and speaker-output interface against the current datasheet before releasing a PCB. This page combines manufacturer product information, exact-MPN distributor availability details, package identification, application guidance, and engineering-focused comparison notes for engineers evaluating TAS5548DCAR in multichannel digital-audio systems.

RFQ İletişim
TAS5558DCA - 8-Channel HD Audio DSP with PWM | Texas Instruments
TAS5558DCA

TAS5558DCA - 8-Channel HD Audio DSP with PWM | Texas Instruments

The Texas Instruments TAS5558DCA is an 8-channel HD-compatible digital audio processor with digital pulse-width modulation output and an integrated sample-rate converter, supplied in a 56-pin HTSSOP DCA package. It operates across the manufacturer-listed temperature range of -40 °C to 85 °C and supports a maximum PWM modulation frequency of 0.4 MHz. Its two independent ASRC modules each handle four channels, allowing simultaneous conversion across all eight output channels. A digital audio processor is a specialized integrated circuit that accepts digital audio data, performs configurable signal processing, and produces a format suitable for downstream power amplification. Within the broader semiconductor hierarchy, the TAS5558DCA belongs to the audio special-purpose IC and digital signal processor categories. Its integrated sample-rate converter, digital audio processing, and PWM generation combine several discrete audio functions into one high-integration device. The principal feature set includes eight audio processing channels, advanced digital audio processing, an integrated sample-rate converter, and eight PWM outputs. These functions target HD-compatible home-theater-in-a-box applications described by Texas Instruments, including systems associated with DTS-HD Blu-ray playback. A 0.4 MHz maximum modulation frequency provides the timing headroom required by the device's specified PWM output architecture. Technically, the TAS5558DCA is designed around two separate ASRC modules rather than one shared converter. Each module processes four channels, allowing up to eight channels to be supported concurrently. This modular channel organization can simplify system partitioning when comparing input sample rates, but it does not eliminate the need to verify supported formats, clocking, and configuration details in the manufacturer documentation. Typical uses include Blu-ray home-theater-in-a-box amplifiers, multi-channel digital audio power stages, powered speakers, and consumer audio systems requiring eight PWM channels. The processor is most appropriate where digital signal processing, sample-rate conversion, and class-D-style PWM modulation must be integrated into a compact design. Designers should preserve the exposed-pad thermal and layout requirements of the HTSSOP package and verify all digital audio interfaces against the manufacturer datasheet. Because several electrical, timing, and pin-level details are not present in the supplied source excerpts, those values must be confirmed in the full Texas Instruments technical documentation before layout release. This page consolidates the verified channel count, package, temperature range, PWM frequency, source links, procurement information, and engineering limitations for TAS5558DCA. It also distinguishes verified facts from missing datasheet parameters, helping engineers evaluate the device without mistaking generic audio-IC characteristics for guaranteed TAS5558DCA specifications.

RFQ İletişim
TAS5558DCAR - 8-Channel HD Audio DSP with PWM | Texas Instruments (Tape & Reel)
TAS5558DCAR

TAS5558DCAR - 8-Channel HD Audio DSP with PWM | Texas Instruments (Tape & Reel)

The Texas Instruments TAS5558DCAR is an 8-channel HD-compatible digital audio processor with digital pulse-width modulation output and an integrated sample-rate converter, supplied in a 56-pin HTSSOP DCA package. It operates across the manufacturer-listed temperature range of -40 °C to 85 °C and supports a maximum PWM modulation frequency of 0.4 MHz. Its two independent ASRC modules each handle four channels, allowing simultaneous conversion across all eight output channels. A digital audio processor is a specialized integrated circuit that accepts digital audio data, performs configurable signal processing, and produces a format suitable for downstream power amplification. Within the broader semiconductor hierarchy, the TAS5558DCAR belongs to the audio special-purpose IC and digital signal processor categories. Its integrated sample-rate converter, digital audio processing, and PWM generation combine several discrete audio functions into one high-integration device. The principal feature set includes eight audio processing channels, advanced digital audio processing, an integrated sample-rate converter, and eight PWM outputs. These functions target HD-compatible home-theater-in-a-box applications described by Texas Instruments, including systems associated with DTS-HD Blu-ray playback. A 0.4 MHz maximum modulation frequency provides the timing headroom required by the device's specified PWM output architecture. Technically, the TAS5558DCAR is designed around two separate ASRC modules rather than one shared converter. Each module processes four channels, allowing up to eight channels to be supported concurrently. This modular channel organization can simplify system partitioning when comparing input sample rates, but it does not eliminate the need to verify supported formats, clocking, and configuration details in the manufacturer documentation. Typical uses include Blu-ray home-theater-in-a-box amplifiers, multi-channel digital audio power stages, powered speakers, and consumer audio systems requiring eight PWM channels. The processor is most appropriate where digital signal processing, sample-rate conversion, and class-D-style PWM modulation must be integrated into a compact design. Designers should preserve the exposed-pad thermal and layout requirements of the HTSSOP package and verify all digital audio interfaces against the manufacturer datasheet. Because several electrical, timing, and pin-level details are not present in the supplied source excerpts, those values must be confirmed in the full Texas Instruments technical documentation before layout release. This page consolidates the verified channel count, package, temperature range, PWM frequency, source links, procurement information, and engineering limitations for TAS5558DCAR. It also distinguishes verified facts from missing datasheet parameters, helping engineers evaluate the device without mistaking generic audio-IC characteristics for guaranteed TAS5558DCAR specifications.

RFQ İletişim
TAS5601DCA - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5601DCA

TAS5601DCA - 20W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5601DCA is a 20 W per channel digital Class-D audio amplifier power stage with a 10 V to 26 V supply and PWM single-ended input. The device is supplied in a 56-pin HTSSOP (DCA) package and can configure its four half-bridge outputs for stereo bridge-tied loads, four single-ended loads, or a mixture of both. A digital Class-D audio amplifier is a switching power stage that uses pulse-width-modulated drive signals to deliver power efficiently to loudspeakers. Unlike a conventional linear audio amplifier, the TAS5601 converts the PWM input into high-frequency switching currents, reducing the amount of power dissipated within the output stage. The TAS5601 belongs to the Class-D amplifier hierarchy, where its four half bridges provide the switching elements required for stereo speaker drive. The principal operating specifications are 20 W per channel, a 10 V to 26 V supply range, and PWM single-ended input. The amplifier is designed for speakers with an impedance as low as 4 ohms. According to the manufacturer datasheet, Rev. A, efficiency exceeds 90% when driving an 8-ohm load. This efficiency figure is especially useful when comparing thermal requirements with less efficient linear amplification approaches. Each output half bridge includes integrated feedback support, allowing the amplifier to operate with a conventional speaker connection rather than requiring a separate analog output filter. The device supports two bridge-tied speakers or four single-ended speakers, and the same output network can also be arranged for a combination of single-ended and bridge-tied loads. The resulting flexibility permits speaker-count changes without changing the amplifier package or control architecture. Typical uses include powered speakers, stereo audio receivers, multimedia speaker systems, sound bars, consumer television equipment, and compact audio products requiring multiple speaker outputs. The 10 V to 26 V supply range is suited to systems using a 12 V or 24 V rail, while the four-half-bridge architecture is useful when the design must accommodate both stereo and multiway speaker configurations. Design the power rails, output inductors, speaker connections, and thermal copper around the maximum 26 V operating condition. Speaker wiring and amplifier outputs must be kept away from sensitive signal paths, and the PCB layout should follow the manufacturer reference layout to control switching noise, ground bounce, and unintended electromagnetic coupling. This page organizes the verified operating characteristics, amplifier configuration options, sourcing information, and engineering trade-offs around the TAS5601DCA. It also distinguishes genuine drop-in alternatives from package or ordering-code variations so that PCB reuse decisions remain based on pin compatibility rather than nominal power capability alone.

RFQ İletişim
TAS5601DCAR - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5601DCAR

TAS5601DCAR - 20W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5601DCAR is a 20 W-per-channel stereo Class-D digital amplifier power stage with PWM single-ended input, a 10 V to 26 V supply range, and a 56-pin HTSSOP DCA package. It supports four single-ended speakers, two bridge-tied speakers, or a mixture of single-ended and bridge-tied loads, including speaker impedances as low as 4 Ω. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an analog audio waveform. Within the amplifier hierarchy, it belongs to the digital amplifier family, power-stage IC category, and broader audio power-management semiconductor group. Compared with a linear audio amplifier, a Class-D stage can deliver high output efficiency while placing less heat in the speaker and amplifier output stages. The TAS5601 is designed as a power stage that accepts a digital audio signal and drives speakers without requiring the traditional analog input-voltage signal path. The headline specifications are 20 W per channel, a 10 V to 26 V supply range, and greater than 90% efficiency into an 8 Ω load. The device can operate as a 2-channel stereo amplifier or a 4-channel single-ended amplifier. Its digital interface supports the common audio-system use cases for compact consumer, multimedia, and powered-speaker products. An operating-temperature range of −40 °C to 85 °C and a surface-mount HTSSOP package support industrial and commercial equipment designs. The TAS5601 uses a feedback-based Class-D power-stage architecture, with the option to drive either bridge-tied or single-ended loads. Feedback-based operation helps the output stage track the intended signal while maintaining low distortion in the target application. The manufacturer identifies efficiency above 90% into an 8 Ω load as sufficient to eliminate the need for an external heat sink in typical configurations. Actual thermal performance still depends on supply voltage, channel loading, board copper, ambient temperature, and the duration of maximum-power operation. Typical applications include compact stereo speakers, multimedia speaker systems, soundbars, television audio modules, portable consumer equipment, and powered peripheral systems. The 4 Ω minimum load capability gives designers flexibility when selecting conventional speaker impedances. The digital input architecture is particularly useful where the audio source already delivers a digital signal, allowing the power stage to be placed close to the speaker connector and away from sensitive source circuitry. PCB design should prioritize short power-loop paths, continuous output-current copper, thermal-via placement beneath the exposed pad, and clean separation between input and output routing. The HTSSOP thermal pad must be connected to the intended ground plane with multiple vias, and output filtering must follow the manufacturer reference layout to control switching-related interference. Component placement should also minimize loop area around the power supply and output bridge. This product page consolidates the official device specifications, pin-compatible-replacement assessment, application guidance, comparison parameters, and practical layout considerations into a design-focused reference. It helps engineers distinguish electrical compatibility from mere package similarity while planning amplifier routing, speaker loading, thermal management, and sourcing.

RFQ İletişim
TAS5602DCA - 20W Stereo PWM-Input Class-D Power Stage | TI
TAS5602DCA

TAS5602DCA - 20W Stereo PWM-Input Class-D Power Stage | TI

The Texas Instruments TAS5602DCA is a 20 W per channel stereo digital Class-D audio amplifier power stage with PWM input, housed in a 56-pin HTSSOP (DCA) package with an exposed thermal pad. It operates from a 10 V to 26 V supply and can drive four single-ended speakers or two bridge-tied (BT) speakers from a single device. A Class-D audio amplifier is a switching power amplifier that delivers audio output by applying a constant-amplitude PWM carrier to the speaker load, so the transistor output stage conducts only when the PWM signal is active. In the device hierarchy, TAS5602DCA belongs to the amplifier IC family, inside audio amplifiers, inside integrated circuits, inside analog power and signal-chain semiconductors. Unlike a conventional analog input amplifier, this part accepts a PWM signal directly from a digital audio processor or a Class-D modulator, eliminating an analog input stage and its associated noise and distortion. Key features include 20 W of continuous output power per channel, a wide 10 V to 26 V operating supply range, and support for both single-ended and bridge-tied speaker configurations. Because the part accepts PWM rather than an analog voltage, the noise floor is set entirely by the upstream digital source, which keeps inter-channel noise and distortion very low and makes channel matching essentially perfect. The device supports 2-channel stereo, 4-channel quad, and mono operation modes, giving a single part number flexibility for multiple speaker topologies. Internally, the TAS5602 architecture combines a half-bridge output stage with integrated feedback control, so the amplifier can be configured with or without a feedback resistor network to suit the target speaker impedance. Because output stage switching is fully synchronous and the modulator runs at a high carrier frequency, the switching losses remain low and the power stage can be mounted on standard two-layer PCB copper without a bulky external heatsink in typical 10 W per channel designs. Typical applications include consumer and industrial audio: multi-room and networked speakers, sound bars, TV and monitor speaker drivers, Bluetooth and Wi-Fi speaker systems, USB and PC audio docks, and powered speaker systems. The 56-pin HTSSOP package with exposed pad provides a large thermal copper area, which is essential for continuous 20 W per channel operation from a 24 V rail. When laying out the board, treat the exposed pad as both the thermal path and the main ground return. Use a solid ground pour with minimal inductance between the output drivers and the supply bypass capacitors, and place the input PWM traces away from the switching node to avoid coupling the carrier frequency into the audio path. This page brings together the manufacturer ordering information, a parameter-by-parameter comparison against related Texas Instruments Class-D power stages, and practical thermal and layout guidance that goes beyond the headline specifications found in the datasheet.

RFQ İletişim
TAS5611APHD - 125W Stereo Class-D Amplifier | Texas Instruments
TAS5611APHD

TAS5611APHD - 125W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5611APHD is an analog-input Class-D audio power amplifier rated for 125 W stereo output or 250 W mono output from a 16 V to 34.1 V supply. The device is packaged in a 64-pin HTQFP PHD package measuring 14 mm by 14 mm and incorporates PurePath HD closed-loop feedback technology. A Class-D audio amplifier is a switching power stage that delivers high audio output power with substantially greater efficiency than a traditional linear amplifier. The TAS5611A family combines a differential analog input, a Class-D output stage, and integrated closed-loop feedback. This places it in the audio amplifier hierarchy alongside stereo power amplifiers, speaker drivers, and power-management ICs used in home audio, automotive, and industrial systems. Key features include configurable mono or stereo operation, 125 W per channel in stereo mode, 250 W in mono mode, and an operating supply range of 16 V to 34.1 V. PurePath HD feedback is intended to improve distortion and frequency-response performance in the power stage. The device accepts an analog input and provides a differential speaker output, allowing direct integration into powered speakers and multi-channel audio systems. The PHD package is a 64-pin HTQFP with an exposed thermal pad. Its high-output topology makes thermal management and PCB copper layout critical: power-stage losses must be transferred through the package and board rather than treated as only an IC-level concern. The manufacturer product page lists the operating temperature as 0 °C to 70 °C for this orderable part. Exact feedback, modulation, efficiency, and thermal values should be confirmed against the manufacturer datasheet before a production design is released. Typical applications include powered bookshelf speakers, compact home-theater amplifiers, professional audio equipment, soundbars, and automotive-style audio modules. Stereo operation uses the device as a dual-channel 125 W amplifier, while bridged mono operation combines the channels for up to 250 W into one speaker. The wide 16 V to 34.1 V supply range suits systems using a nominal 24 V automotive or industrial bus after appropriate regulation and protection. A critical design requirement is to provide the datasheet-recommended power and ground layout, use a low-inductance speaker-output path, and connect the exposed thermal pad to an adequate copper area. The analog input and feedback network also require careful grounding to prevent channel interaction. Validate peak thermal conditions and speaker impedance at the maximum intended output power. This product guide combines the exact orderable-part characteristics, package details, application guidance, replacement considerations, and practical layout checks needed to evaluate the TAS5611APHD as a high-power Class-D audio solution.

RFQ İletişim