Ürünler (44.000+)

TAS5611PHD - 125W Stereo/250W Mono Class-D | Texas Instruments
TAS5611PHD

TAS5611PHD - 125W Stereo/250W Mono Class-D | Texas Instruments

Texas Instruments TAS5611PHD is an analog-input Class-D audio power stage rated for up to 125 W stereo output or 250 W mono output, housed in a 64-pin HTQFP package with an exposed thermal pad. The device supports a 32.5 V supply and is designed to drive 4 Ω to 8 Ω speakers, combining Class-D efficiency with the low distortion traditionally associated with Class-AB amplification. A Class-D audio power stage is a switching amplifier category that uses transistor output stages to deliver high audio power efficiently. Unlike a linear Class-AB amplifier, its output transistors operate principally in switching states, reducing conduction losses. PurePath HD, the integrated closed-loop feedback technology used in the TAS5611, helps the device achieve total harmonic distortion below 0.03% while retaining the efficiency advantage of Class-D operation. The headline capabilities include analog signal input, 125 W stereo or 250 W mono output, support for 4 Ω to 8 Ω speaker loads, and operation from a single 32.5 V supply. The 64-pin HTQFP package measures 14 mm by 14 mm and incorporates an exposed pad that requires careful PCB thermal design. These characteristics make the device suitable for high-power consumer audio, home-theater amplification, powered speakers, and compact professional audio systems. The PurePath HD architecture is central to the amplifier’s performance. Integrated closed-loop feedback monitors the output waveform and corrects nonlinear distortion introduced by the power stage. In an analog-input implementation, the amplifier accepts a conventional audio signal rather than requiring a digital audio codec, allowing it to operate with preamplifiers, tone-control circuits, volume-control stages, or other line-level sources. Analog input also keeps the signal chain compatible with existing analog audio equipment. Typical uses include stereo home-theater receivers, powered bookshelf speakers, active subwoofers, compact stereo amplifiers, and single-channel high-output installations. A bridge-tied mono configuration can increase the available power into one speaker load, while the stereo configuration distributes the amplifier’s output between two channels. Appropriate speaker selection and power-supply design remain essential because actual thermal performance depends strongly on the PCB copper area, heat spreading, supply capability, and enclosure ventilation. The principal design consideration is heat management. The exposed thermal pad must be connected to a properly designed copper heat-spreading area, and the amplifier’s operating mode must be evaluated at the intended load impedance and power level. Inductor selection, speaker filtering, grounding, and high-current supply routing also influence switching noise, output stability, and EMI performance. The manufacturer’s reference layouts should be used as the starting point for a new design. This page combines the verified 125 W stereo, 250 W mono, 32.5 V, distortion, package, and application information with practical selection guidance, package considerations, and clearly qualified drop-in alternatives. It is intended to help engineers determine whether the TAS5611PHD fits a high-power analog-input Class-D design before beginning board-level implementation.

RFQ İletişim
TAS5612PHD - 125W Stereo Class D Amplifier | Texas Instruments
TAS5612PHD

TAS5612PHD - 125W Stereo Class D Amplifier | Texas Instruments

The Texas Instruments TAS5612PHD is a PurePath HD Class D audio power amplifier rated for 125 W per channel in stereo operation and 250 W in mono operation. It accepts one-channel mono or two-channel stereo signals and is packaged in a 64-pin HTQFP measuring 14 mm by 14 mm. The device is intended for high-power audio systems requiring efficient amplification into 4 ohm to 8 ohm speaker loads. A Class D audio amplifier is a switching power amplifier whose transistor output stage operates with controlled PWM signals. Compared with a linear audio amplifier, this topology can convert amplifier input power into speaker output power more efficiently, reducing heat and allowing high output power in a compact package. The TAS5612PHD belongs to the broader hierarchy of audio amplifiers, audio power amplifiers, power management ICs, and semiconductors. The primary performance ratings are 125 W stereo output, 250 W mono output, and operation from a 16 V to 34.1 V supply range. A 10.8 V to 13.2 V range is also associated with the device in the technical listing. Its integrated closed-loop feedback technology, called PurePath HD, helps the amplifier correct output-voltage distortion through the speaker connection rather than relying only on feedback around the power stage. The device supports either one-channel mono operation or two-channel stereo operation. This flexibility makes it suitable for home-theater power stages, professional audio amplification, subwoofer amplifiers, and compact high-power speaker systems. The 64-pin HTQFP package requires a carefully designed exposed-pad thermal layout, and its power-class application makes heat dissipation a central PCB-design requirement. For robust implementation, designers should follow the manufacturer datasheet for the recommended power topology, input filtering, speaker output network, supply decoupling, and thermal land pattern. The evaluation module TAS5612/14PHD2EVM provides a practical reference for evaluating TAS5612PHD alongside TAS5614PHD and TAS5518PAG in a PurePath HD audio system. This page combines the manufacturer device ratings with practical guidance for thermal management, output-network implementation, supply decoupling, and device selection. It also distinguishes confirmed family alternatives from components that only provide related functionality but cannot be assumed to be pin-compatible replacements.

RFQ İletişim
TAS5613PHD - 150W Stereo Class-D Power Stage | Texas Instruments
TAS5613PHD

TAS5613PHD - 150W Stereo Class-D Power Stage | Texas Instruments

The Texas Instruments TAS5613PHD is a 150 W stereo Class-D audio power stage with integrated feedback, analog input, and 64-pin HTQFP packaging. It operates from an 18 V to 38 V power-supply range, supports a 10.8 V to 13.2 V analog input range, and supports mono or stereo output configurations. The device also provides signal bandwidth up to 80 kHz for high-definition audio content. A Class-D audio power stage is an efficient switching amplifier that converts analog audio signals into high-power drive for loudspeakers. It belongs to the amplifier IC hierarchy, specifically the audio amplifier and power-amplifier categories. Compared with linear audio amplifiers, Class-D architectures can provide high output power with lower power dissipation because the switching elements are operated near their fully-on or fully-off states. Integrated feedback helps the device regulate its power stage and supports repeatable amplifier design. The TAS5613PHD delivers up to 150 W in a stereo configuration and up to 300 W in a mono configuration. According to the manufacturer product page, distortion can be as low as 0.03% THD at 1 W into 4 ohms, while flat total harmonic distortion across frequency is positioned for natural sound reproduction. Power-supply rejection reaches 80 dB in bridge-tie-load operation without an input signal, and signal-to-noise ratio can exceed 100 dB when weighted for A. The device uses PurePath HD analog-input technology and provides click-and-pop-free startup and shutdown behavior. Its integrated-feedback architecture is intended to simplify power-stage implementation while retaining high-frequency signal capability. The manufacturer identifies pin compatibility with the TAS5630, TAS5615, and TAS5611 families, enabling designers to evaluate different power levels or feature sets while retaining a common package strategy. Typical applications include high-power stereo audio receivers, active loudspeakers, home-theater amplification, multichannel audio systems, and compact subwoofer or full-range driver stages. The 150 W stereo rating is particularly relevant to consumer and professional audio equipment where a single integrated stage can drive conventional passive loudspeakers efficiently. The 300 W mono configuration offers additional flexibility for bridged applications or higher-power single-channel systems. Thermal design remains a central implementation consideration because Class-D power stages concentrate losses in the switching devices and package. Follow the manufacturer’s recommended land pattern, component placement, thermal-pad connection, power-supply decoupling, and output-filter guidance. Account for worst-case supply voltage, channel imbalance, amplifier gain, and enclosure temperature rather than sizing the system only from nominal output power. This page organizes the manufacturer’s key technical facts, package information, family relationships, and engineering guidance for faster component evaluation. The comparison and selection sections also clarify how the pin-compatible TAS5613PHD relates to other PurePath HD power stages when power capability, channel architecture, and thermal requirements differ.

RFQ İletişim
TAS5614PHD - 150W Stereo Class D Power Stage | TI
TAS5614PHD

TAS5614PHD - 150W Stereo Class D Power Stage | TI

The Texas Instruments TAS5614PHD is a 150W stereo or 300W mono Class D audio power stage using PurePath HD technology and housed in a 64-pin HTQFP package measuring 14 x 14 mm. It accepts analog audio input and uses integrated closed-loop feedback to drive 4 ohm to 8 ohm speakers from a single supply rated up to 36V. A Class D audio power stage is a switching amplifier that converts an analog audio waveform into a high-frequency PWM output, filtering it at the speaker terminals to recover the amplified audio signal. Its place in the hierarchy is audio power IC, power amplifier IC, Class D amplifier, and power-management semiconductor. Compared with a linear amplifier, the switching architecture can substantially reduce output-stage dissipation while maintaining low distortion through closed-loop feedback. The headline capabilities are 150W stereo output, 300W mono output, a Class D output stage, analog input, and PurePath HD feedback. The device can operate from an 18V to 38V supply range, while published supply figures also identify a 10.8V to 13.2V operating condition. The manufacturer positions the part for driving 4 ohm to 8 ohm stereo speakers from one 36V supply, making it relevant to powered speakers, AV receivers, compact cinema systems, and professional audio equipment. The TAS5614PHD is intended as a power-stage device rather than a complete audio system controller. Its input and digital-control functions must be integrated with a preamplifier or codec that supplies the audio signal. Closed-loop PurePath HD feedback is the central architecture feature: the amplifier monitors its output and corrects the switching stage to reduce distortion rather than relying only on open-loop drive accuracy. Because the device dissipates substantial power at high output levels, the exposed heatslug is central to the mechanical design. Texas Instruments specifies a high-performance thermal interface material between the package heatslug and the heat sink. The 14 x 14 mm HTQFP package therefore needs a defined heat-spreading and convection path to sustain the 150W stereo and 300W mono ratings. This page combines the manufacturer product information with distributor listings and a package-level comparison for design planning. Because the detailed pin-description and thermal tables reside in the manufacturer datasheet, use that document for final pin assignment, exposed-pad treatment, filter selection, and heat-sink design.

RFQ İletişim
TAS5615DKD - 160W Stereo Class-D Amplifier | TI
TAS5615DKD

TAS5615DKD - 160W Stereo Class-D Amplifier | TI

Texas Instruments TAS5615DKD is an analog-input Class-D audio power amplifier with integrated closed-loop feedback using PurePath HD technology. It supports up to 160 W stereo output into 8-ohm speakers from a single 50 V supply, or up to 300 W mono operation, and is packaged in a 44-pin HSSOP package. According to the manufacturer product page, distortion is below 0.03% THD while retaining the efficiency associated with Class-D operation. A Class-D audio power amplifier is a switching power stage that converts an analog input waveform into a high-frequency PWM representation and reconstructs the audio signal at the speaker output. The TAS5615 family belongs to the broader class of integrated audio amplifiers, combining a power-conversion stage with feedback control in one device. Its integrated PurePath HD closed-loop feedback system is intended to improve linearity and reduce distortion compared with relying only on an external speaker feedback network. The TAS5615DKD accepts analog audio inputs and is designed for high-power stereo and mono speaker drive. Its stated 160 W stereo capability is based on operation from a 50 V supply, while the 300 W mono figure supports dedicated single-channel or bridged configurations. The supported power-supply range shown in the component listing is 25 V to 52.5 V, and a separate 10.8 V to 13.2 V range is associated with its internal auxiliary supply domain. PurePath HD technology is the principal technical differentiator of this power stage. Closed-loop feedback samples the output and corrects the switching waveform, supporting the manufacturer’s specified total harmonic distortion below 0.03%. This combination of analog input, Class-D efficiency, and feedback-based distortion control makes the device suitable for professional audio amplification, home-theater receivers, powered speakers, subwoofers, and other systems using low-impedance loudspeakers. For stereo installations, the amplifier drives left and right channels from analog inputs while operating from a high-voltage supply. A bridged mono arrangement can increase the available output into one speaker or a matched pair of speakers. The exact output power depends on supply voltage, speaker impedance, channel configuration, thermal conditions, and the load presented by the speaker network, so these conditions must be confirmed during amplifier and thermal design. The 44-pin HSSOP package requires careful PCB layout and adequate copper for heat removal. Power and ground connections should use short, wide traces with low loop area, while the manufacturer’s layout guidance should govern input routing, feedback connections, decoupling, and thermal via placement. The device is a power IC, but thermal design must use the maximum expected dissipation at the selected supply voltage and load rather than relying only on nominal output power. This product page combines the manufacturer’s core performance claims with package, interface, supply, and sourcing details, while adding application guidance and verified drop-in replacement status for engineering evaluation. Use the Request a Quote form for current commercial availability, and consult the manufacturer datasheet before finalizing the PCB, heat sink, output network, and protection scheme.

RFQ İletişim
TAS5615PHD - 300W Mono Class-D Power Stage | Texas Instruments
TAS5615PHD

TAS5615PHD - 300W Mono Class-D Power Stage | Texas Instruments

The Texas Instruments TAS5615PHD is an analog-input Class-D audio power stage with integrated PurePath HD closed-loop feedback, capable of delivering up to 300 W mono output or 160 W stereo output into 8-ohm speakers from a single 50 V supply. It is packaged in a 64-pin HTQFP power package measuring 14 mm by 14 mm and includes an exposed thermal pad for heat dissipation. The device supports mono, stereo, and four-channel speaker configurations while maintaining total harmonic distortion below 0.03% under the conditions stated by Texas Instruments. A Class-D audio power amplifier is a switching amplifier that uses pulse-width modulation to deliver speaker power efficiently. The TAS5615PHD belongs to the Class-D amplifier, audio power IC, and power-management semiconductor hierarchy. Unlike a conventional linear Class-AB output stage, its switching architecture concentrates unwanted energy at high frequencies, reducing output-stage heat while retaining low audio distortion through the integrated closed-loop feedback system. The headline features include analog input, support for a 50 V power-stage supply, up to 160 W per channel in stereo operation, and up to 300 W in mono operation. PurePath HD feedback is intended to suppress distortion associated with output-network component variation. The device accepts conventional analog audio signals, which simplifies its use in systems that do not require a PWM audio source. Its 64-pin HTQFP package provides numerous power, feedback, ground, signal, and control connections needed for a high-power output stage. The PurePath HD architecture continuously corrects the output waveform using feedback sensed from the speaker output. This approach is intended to provide Class-AB-like fidelity while retaining the efficiency of a Class-D output stage. Texas Instruments specifies distortion below 0.03%, making the device suitable for high-fidelity amplification where audible distortion, clipping, or thermal losses would otherwise constrain the amplifier selection. Typical uses include powered speakers, home-theater amplifiers, professional audio equipment, soundbars, multichannel audio systems, and compact high-power subwoofer or surround-speaker platforms. In a stereo design, the integrated output stages drive left and right channels. In a mono design, the power capability can be consolidated for a single loudspeaker or bridged audio architecture, subject to the thermal and load limitations in the manufacturer datasheet. Careful thermal design is essential because the exposed pad must dissipate power generated by the switching output stage. Follow the manufacturer application diagrams for the power-supply topology, output inductors, feedback network, input filtering, copper area, and thermal layout. The 50 V power-stage rail should have low output impedance and low noise, and the 12 V supply should originate from a low-noise, low-output-impedance regulator. This page organizes the verified power ratings, package information, operating architecture, application fit, and engineering cautions for the TAS5615PHD. It also distinguishes the target device from related TI products so design engineers can determine whether the analog-input interface, power rating, package, and thermal requirements match the intended amplifier platform.

RFQ İletişim
TAS5616DKD - 300W Mono Class-D Amplifier | Texas Instruments
TAS5616DKD

TAS5616DKD - 300W Mono Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5616DKD is a digital-input Class-D audio power amplifier with integrated PurePath HD feedback, designed for mono or stereo speaker drive. It supports 25 V to 52.5 V power-supply operation, 10.8 V to 13.2 V PWM logic supply operation, 160 W stereo output into 8-ohm loads, and up to 300 W mono output. The device is packaged in a 44-pin HSSOP power package with an exposed thermal pad. A Class-D amplifier is a switching audio power stage in which the output transistor operates in a fully switching state. Its efficiency allows substantial audio power with lower conduction loss than a conventional linear amplifier. The TAS5616DKD is a high-performance PWM-input Class-D device with integrated closed-loop feedback, providing a practical solution for powered speakers, home-theater equipment, and compact high-power audio systems. Key characteristics include a 44-pin HSSOP package, integrated closed-loop feedback, digital PWM input, support for mono or stereo operation, and a power-supply range of 25 V to 52.5 V. The device also accepts a separate 10.8 V to 13.2 V PWM supply, allowing the system designer to manage power-amplifier and logic-supply domains independently. The exposed thermal pad is central to heat removal at high output power. The PurePath HD architecture uses integrated feedback to improve distortion and output-voltage behavior in the power stage. With an 80 kHz signal-bandwidth capability described for the device family, the amplifier is intended for high-fidelity audio reproduction rather than low-frequency-only subwoofer applications. The integrated feedback simplifies output-network design compared with systems that require external speaker feedback. Typical uses include powered stereo speakers, compact home-theater amplifiers, professional audio equipment, soundbars, and high-power subwoofer amplifiers. In each case, the supply voltage, speaker impedance, thermal design, and output-filter requirements must be selected together. The 44-pin HSSOP package requires careful PCB layout and substantial thermal copper for reliable operation near its maximum output capability. The main design consideration is heat management. Estimated power dissipation in the output stage changes with supply voltage, output voltage, load impedance, and output power. Use the exposed pad with a low-thermal-resistance PCB layout, validate amplifier temperature during maximum-power operation, and select decoupling and output filtering according to the manufacturer datasheet. This product summary combines the electrical ratings, package information, application context, practical thermal guidance, and drop-in replacement considerations for engineers evaluating the TAS5616DKD in Class-D audio designs.

RFQ İletişim
TAS5616PHD - 160W Stereo Class-D Amplifier | Texas Instruments
TAS5616PHD

TAS5616PHD - 160W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5616PHD is a PurePath HD digital-input Class-D power-stage amplifier rated for 300 W mono operation or 160 W stereo operation. It operates from a 25 V to 52.5 V supply and is packaged in a 64-terminal, 14 mm by 14 mm HTQFP power-package with an exposed thermal pad. The device accepts a digital audio input and uses integrated closed-loop feedback to drive speaker outputs. A Class-D amplifier is a switching power amplifier that converts a digital or analog input into a pulse-width-modulated output waveform. This approach belongs to the broader power-amplifier hierarchy and can deliver high output power efficiently when the switching stage, output filter, power supply, and thermal system are designed correctly. The TAS5616PHD targets high-power audio products where low total harmonic distortion, wide signal bandwidth, and compact output-stage construction are important. Key features include a 300 W mono output rating, a 160 W stereo output rating, a 25 V to 52.5 V supply range, integrated closed-loop feedback, digital input, and signal bandwidth extending to 80 kHz. These characteristics make the amplifier suitable for powered speakers, home-theater systems, professional audio equipment, soundbars, and compact consumer-audio products requiring more output power than a conventional analog audio amplifier can provide efficiently. PurePath HD feedback is the principal technical distinction of this device. The feedback system monitors the output stage and corrects switching behavior, supporting improved audio fidelity while retaining the efficiency associated with Class-D operation. Because the device is a digital-input power stage, the system designer must also address the digital audio interface, clocking, signal integrity, switching-node layout, output filtering, and electromagnetic compatibility between the amplifier and its speakers. Typical applications include a 300 W subwoofer power stage, a 160 W stereo speaker amplifier, a powered bookshelf speaker, a home-theater receiver, and a compact high-output audio system. The 64-terminal exposed-pad package requires deliberate PCB copper and thermal management; the thermal pad is an electrical connection as well as a heat-spreading structure and must be connected according to the manufacturer layout guidance. The primary design trade-off is that a 52.5 V-class power stage requires a suitably rated supply, carefully laid-out switching nets, and an output-filter strategy appropriate for the selected speaker impedance and bandwidth. Verify DC offset, thermal performance, filter stability, and amplifier protection behavior with the intended speakers rather than assuming that nominal power ratings represent unrestricted continuous output in every enclosure.

RFQ İletişim
TAS5630DKD - 300W Stereo Class-D Amplifier | Texas Instruments
TAS5630DKD

TAS5630DKD - 300W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5630DKD is an analog-input Class-D audio power amplifier using PurePath HD integrated closed-loop feedback, with capability to deliver up to 300 W stereo or 600 W mono into 4 Ω to 8 Ω speakers. It is supplied in a 44-pin HSSOP power package with an exposed heat slug for thermal-interface installation. Achievable output power depends on the thermal configuration of the application. A Class-D amplifier is a switching audio power stage in which the output transistors operate at high frequency and deliver speaker current with high efficiency. In the amplifier hierarchy, the TAS5630 belongs to the audio amplifier IC category, then to the Class-D amplifier group and finally to the power-amplifier IC class. Its integrated closed-loop feedback is intended to reduce distortion associated with conventional open-loop Class-D output stages, while retaining the efficiency benefits of switching conversion. The main performance attributes are up to 300 W stereo output, up to 600 W mono operation, 4 Ω to 8 Ω speaker compatibility, and a 50 V power-stage supply assumption. The manufacturer documentation also shows a 10.8 V to 13.2 V signal-supply range in its application description. The 44-HSSOP package provides a large thermal connection area, but power capability depends on the heat sink, thermal interface material, copper area, board construction, and ambient conditions rather than package marking alone. PurePath HD technology is the defining architectural feature. The TI product page identifies the TAS5630 as a high-performance analog-input Class-D amplifier with integrated closed-loop feedback. Analog input allows compatibility with conventional line-level audio signals, while the integrated feedback arrangement supports a power-stage design intended for high-output applications. The manufacturer specifically recommends a low-noise, low-output-impedance 12 V regulator for the signal supply and a low-impedance, low-noise 50 V power-stage supply. Typical uses include professional power amplifiers, high-power stereo audio systems, cinema and home-theater speaker amplification, and bridged mono installations for subwoofers or full-range speakers. The device is particularly relevant where a single power amplifier must support both stereo and bridged-mono configurations, although the external supply, output-filter, speaker, and thermal designs remain application-specific. Thermal design is the principal implementation constraint. The exposed package heat slug must be coupled to a suitable heat sink through a high-performance thermal interface material, and the power stage requires stable, low-impedance supplies. Use the application diagrams in the manufacturer datasheet to select inductors, capacitors, power-supply components, and the PCB thermal interface for the intended output impedance and power level. This page organizes the manufacturer specifications, verified source links, application guidance, and replacement considerations into an engineering-focused reference. It also distinguishes confirmed package and output capabilities from parameters that require direct checking in the TI datasheet before schematic release, PCB construction, or production procurement.

RFQ İletişim
TAS5630PHD - 300W Stereo Class-D Power Stage | Texas Instruments
TAS5630PHD

TAS5630PHD - 300W Stereo Class-D Power Stage | Texas Instruments

Texas Instruments TAS5630PHD is an analog-input Class-D audio power stage with integrated closed-loop feedback, rated for up to 300 W stereo output from a single 50 V supply in a 64-pin HTQFP package. Depending on the thermal configuration, the device can also support a 600 W mono output configuration. A Class-D audio power stage is a semiconductor amplifier category that converts a PWM switching output into a filtered analog speaker signal. The TAS5630 belongs to the Class-D amplifier, audio power amplifier, and power management IC hierarchies. Its PurePath HD architecture integrates closed-loop feedback, linking the power-stage output to the analog input and reducing sensitivity to load-dependent nonlinear distortion. The principal characteristics are 300 W maximum stereo output power, support for 4 Ω to 8 Ω speaker loads, and operation from a single 50 V supply. The device accepts analog audio input and can be configured for mono or stereo operation. These attributes suit high-power audio systems where efficiency, low heat loss, and accurate speaker-current feedback are important. The integrated feedback architecture distinguishes the TAS5630 from basic open-loop Class-D solutions. It monitors output behavior through the feedback network, allowing the amplifier to correct nonlinear output distortion. Because achievable power depends strongly on the PCB, power-supply design, thermal interface material, and heat-sink configuration, a nominal 300 W rating should not be treated as a guaranteed output level in an arbitrary enclosure. Typical applications include powered loudspeakers, active PA cabinets, professional audio consoles, home-theater power amplifiers, subwoofer amplifiers, and compact high-power stereo receivers. The 50 V supply requirement places the device in the high-voltage class-D power-stage category, requiring careful component spacing, a substantial thermal interface, and robust high-voltage layout practices. Designers should follow the manufacturer datasheet reference layout for the exposed heat slug, power stages, output network, and analog input routing. The package must be coupled to an appropriately sized heat sink through high-performance thermal interface material. Power-supply and output-network components also require voltage, current, pulse-energy, and thermal ratings suitable for Class-D operation. This product page combines the manufacturer power-stage capabilities, exact package information, thermal guidance, sourcing details, and replacement analysis. It also identifies where a true same-footprint replacement cannot be confirmed, preventing a merely similar amplifier from being presented as a drop-in substitute.

RFQ İletişim
TAS5631DKD - 300W Stereo Class D Power Stage | Texas Instruments
TAS5631DKD

TAS5631DKD - 300W Stereo Class D Power Stage | Texas Instruments

The Texas Instruments TAS5631DKD is a PWM-input Class D audio power amplifier built on PurePath HD technology with integrated closed-loop feedback, capable of delivering 300 W per channel in stereo into 4- to 8-ohm speakers from a single 50 V supply, or 600 W in mono, in a 44-pin HTSSOP (DKD) package. The power stage accepts a 3.3 V-compatible PWM input rather than an analog signal, and operates from a 25 V to 52.5 V supply range with a 10.8 V to 13.2 V control/PWM supply domain. A Class D audio power amplifier is a switching power stage in which the output transistors are driven fully on and fully off, so the device dissipates far less energy than a linear (Class AB) amplifier at the same output level. Class D stages are the default choice for high-power consumer and professional audio: they combine high efficiency with high current capability into low-impedance loads. The PurePath HD family sits one level above ordinary Class D, adding a self-contained feedback loop inside the power stage so that distortion can be held below 0.03% without an external analog feedback network. Key features include 300 W stereo and 600 W mono output capability, integrated closed-loop feedback, PWM input with no analog input pin, an efficiency of roughly 90% at full power, integrated undervoltage and overcurrent protection, and an exposed thermal pad on the HTSSOP-44 package for direct coupling to the PCB copper. The device is intended to be paired with a PWM processor such as the TAS5086 to form a complete chipset. Technically the TAS5631 is a self-contained power stage: four bridge-tied output channels drive the speaker outputs, and the on-die feedback network senses the output voltage and corrects the drive so that the effective loop gain stays high even with long speaker cable runs and inverting or non-inverting configurations. Because the feedback is internal, the design work shifts from analog loop compensation to digital PWM generation, timing, and thermal management of the board. Typical applications include multi-channel home theater and AV receivers, active soundbars and wireless loudspeakers, powered subwoofers, smart speakers with cloud audio playback, professional powered speakers and stage-monitor amplifiers, and automotive head-unit or amplifier sub-systems. The dominant design consideration is thermal. At 300 W per channel into a 4-ohm load, the output stage dissipates a substantial fraction of the DC input power, so the exposed thermal pad must be soldered with a proper thermal via array and tied to a large copper pour, otherwise output power must be derated. Follow the recommended PCB layout, filter, and thermal via guidelines in the manufacturer datasheet when laying out the power stage. This page combines the manufacturer power-stage specifications with practical thermal, layout, and signal-chain guidance, drop-in replacement options in the same 44-pin HTSSOP footprint, and application notes that go beyond a parameter table.

RFQ İletişim
TAS5701PAP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5701PAP

TAS5701PAP - 20W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5701PAP is a 20-W stereo digital-input Class-D audio power amplifier with hardware control, operating from a 0- to 21-V supply in a 64-pin HTQFP (PAP) package measuring 10 x 10 mm. Two serial data inputs support up to three discrete audio channels, with SDIN1 routed to internal left and right outputs and SDIN2 dedicated to SUB_PWM± outputs. A Class-D audio power amplifier is a switching power-conversion device that efficiently delivers audio energy to bridge-tied speakers. The Class-D hierarchy is part of switching amplifiers, audio amplifiers, and broader power-management semiconductors. Unlike a linear output stage, a Class-D design moves most signal amplification into switching transistors, improving efficiency while requiring careful output filtering, power-supply design, and electromagnetic-interference control. The TAS5701PAP provides 20 W of stereo audio power and accepts digital audio data, making it suitable for consumer audio equipment that receives its source signal from a digital audio codec or processor. Its hardware control interface supports integration into systems requiring amplifier enable, mute, reset, or operating-mode management. The device is offered in a surface-mount HTQFP package with 64 pins and an operating temperature range of 0°C to 85°C. Internally, the device uses digital audio input and PWM-based output modulation. SDIN1 supplies the left and right stereo channels, while SDIN2 supports dedicated subwoofer PWM outputs. The TAS5701 operates as a clock-slave device, meaning it requires clocks from an external source rather than generating the master audio clock itself. This architecture simplifies synchronization with a digital audio processor but makes the external clock and serial-data timing central to the system design. Typical applications include compact stereo speakers, powered multimedia speakers, sound bars, active subwoofer systems, and digital audio products requiring a bridge-tied Class-D output stage. The dedicated subwoofer PWM path can support systems combining stereo playback with an additional low-frequency channel. Because the amplifier is not a linear audio amplifier, its supply rails and output filters strongly influence noise, distortion, and EMI behavior. When implementing this device, use the manufacturer datasheet reference layout and place the input, supply, ground, and output-filter components according to the specified layout. Maintain short high-current supply paths and adequate ground-plane continuity. Check speaker impedance, output-filter component tolerances, thermal conditions, and the external master-clock requirements before releasing the PCB layout. This page consolidates verified manufacturer and distributor information, strict same-package replacement screening, package and lifecycle details, and practical design guidance. It distinguishes confirmed TAS5701PAP characteristics from parameters that require confirmation in the manufacturer datasheet or current authorized-channel quotation.

RFQ İletişim
TAS5704PAP - 20W Stereo Class-D Amp | Texas Instruments
TAS5704PAP

TAS5704PAP - 20W Stereo Class-D Amp | Texas Instruments

The Texas Instruments TAS5704PAP is a 20 W stereo, digital-input Class-D audio power amplifier operating from a 10 V to 26 V supply and packaged in a 64-pin HTQFP (PAP) with exposed pad. It supports stereo or quad-channel processing, speaker equalization, dynamic range control, hardware control, and digital feedback for efficient bridge-tied speaker drive. A Class-D audio power amplifier is a switching amplifier within the broader hierarchy of audio amplifiers, analog and mixed-signal ICs, and semiconductor signal-processing devices. Instead of operating the output transistor continuously as a linear amplifier, it uses a switching output stage to convert a digital or analog audio signal into high-efficiency bridge-tied speaker drive. The TAS5704 integrates digital signal processing, modulation, and output-stage functions into one device. Key features include 20 W per stereo channel into an 8 ohm load from an 18 V supply, two serial digital audio inputs supporting up to four discrete channels, and a hardware-configurable data path. These features allow the amplifier to interface with compatible digital audio processors while providing system-level control over channel routing, speaker EQ, DRC, and mute or shutdown behavior. The device uses a digital audio datapath and a feedback architecture to monitor the Class-D output stage. The two serial inputs accept multiple discrete channels and operate with digital processors that support compatible data formats and clock rates. An exposed thermal pad beneath the 64-pin package provides the primary heat-transfer path from the power amplifier and control circuitry to the PCB. Typical uses include compact stereo speakers, powered Bluetooth and Wi-Fi speaker systems, soundbars, consumer audio equipment, and other products that require a digital Class-D output stage with local EQ and DRC. The integrated processing can reduce the need for separate audio DSP components when the required presets and routing functions are supported by the TAS5704 configuration. PCB design should preserve the exposed-pad thermal path with a continuous ground plane and via array, place power-supply and ground connections close to the device, and route sensitive clock and serial-data lines away from switching-node conductors. Speaker and supply connections must also be sized for the intended output power; otherwise connector, copper, and thermal limitations can restrict real-world output below the stated 20 W condition.

RFQ İletişim
TAS5705PAP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5705PAP

TAS5705PAP - 20W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5705PAP is a 20 W stereo digital-input Class-D audio power amplifier with an 8 V to 23 V supply range, speaker equalization and dynamic range control, packaged in a 64-pin HTQFP (PAP) package. It is designed to drive stereo bridge-tied speakers while accepting digital audio from a compatible processor. A Class-D audio power amplifier is a switching-based amplifier that delivers speaker output at high efficiency compared with conventional linear audio amplifiers. The TAS5705 belongs to the hierarchy digital audio power amplifier, Class-D amplifier, audio amplifier, amplifier IC and power-management semiconductor. Its digital signal path allows system-level processing to be integrated closer to the speaker output while retaining a compact surface-mount implementation. Verified product information identifies the TAS5705 as a 20 W stereo device with an 8 V to 23 V supply, digital input, open-loop Class-D architecture, speaker EQ and DRC. Distributor listings also describe the PAP configuration as a two-channel amplifier with stereo headphone and subwoofer features. These characteristics position it for consumer audio systems requiring a digital audio interface and local speaker-drive capability. The open-loop Class-D topology delegates loop filtering to external components, allowing the analog filter design to be selected for the intended speaker bandwidth, output-power target and system cost. Integrated EQ and DRC provide tools for controlling tonal response and limiting output excursion, although exact processing configuration depends on the device registers and the associated control software or external digital processor. Typical uses include compact stereo speakers, multimedia systems, sound bars, home-audio products and consumer audio receivers with a digital signal source. Digital input makes the device especially useful where the host processor already provides decoded PCM audio and system designers want to keep the audio signal in the digital domain until the final power-amplifier stage. A key design consideration is that the external LC filter and speaker load directly affect achievable output power, distortion and stability. Layout should follow the manufacturer's recommended application circuit, keep switching-current paths compact and place the filter components close to the appropriate output pins. This page consolidates verified manufacturer and distributor information, drop-in replacement candidates, package details and engineering guidance into one searchable reference for designers evaluating the TAS5705PAP in digital-input stereo audio systems.

RFQ İletişim
TAS5706PAP - 20W Stereo I2S Class D Amplifier | TI
TAS5706PAP

TAS5706PAP - 20W Stereo I2S Class D Amplifier | TI

Texas Instruments TAS5706PAP is a 20 W stereo closed-loop I2S audio power amplifier with speaker EQ and DRC, packaged in a 64-pin HTQFP (PAP) measuring 10 x 10 mm. It supports two-channel stereo or four-channel quad operation, processes as many as four discrete audio channels, and is designed to drive stereo bridged-tied speakers through an efficient Class D output stage. A Class D audio power amplifier is a switching-based amplifier that delivers audio through a high-efficiency output stage. Its hierarchy places it within digital audio amplifiers, then audio amplifiers, then analog and mixed-signal integrated circuits. The TAS5706PAP combines a digital serial-audio input interface, programmable signal routing, speaker equalization, and dynamic range control in one device. This integration reduces the need for separate digital signal processing in systems requiring local audio conditioning. Three headline features define the device: up to 20 W of stereo output power, an I2S-compatible digital audio interface, and closed-loop Class D amplification. The amplifier can route as many as four discrete audio channels to its internal outputs, while its speaker EQ and DRC functions add system-level acoustic processing. The 64-pin HTQFP package supports compact surface-mount implementation in consumer audio and communication equipment. The TAS5706PAP accepts serial digital audio data from digital audio processors and MPEG decoders. Its programmable data path provides flexible channel routing, and two serial data inputs allow a system to handle multiple discrete channels. Because the processing and output functions are integrated, a designer can place EQ and dynamic range control immediately before the power-conversion stage instead of implementing those operations in an external processor. Typical applications include powered speakers, compact stereo audio systems, soundbars, automotive or portable audio products, and embedded multimedia equipment. The closed-loop output architecture is particularly appropriate for bridged-tied speaker configurations where the amplifier must support the speaker load while maintaining the required output-power level. Systems should also account for the device's digital audio configuration and power-delivery requirements during board layout. The primary design consideration is preserving the integrity of the I2S clock and data signals while providing clean, stable power to the Class D output stage. Layout should minimize high-current output-loop area, provide appropriate supply and ground-return paths, and separate sensitive digital inputs from switching-node energy. Speaker filtering and output-network implementation must also be selected for the intended load and acoustic response. This page consolidates the verified manufacturer description, distributor package information, technical source links, application guidance, and honest replacement analysis for TAS5706PAP. It also identifies where verified public data is limited, avoiding invented electrical details or unsupported drop-in substitutions.

RFQ İletişim
TAS5707PHP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5707PHP

TAS5707PHP - 20W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5707PHP is a 20-W open-loop stereo digital-input Class-D audio power amplifier with speaker EQ and dynamic range control (DRC), housed in a 48-pin HTQFP (PHP) package. The device is intended for driving stereo bridge-tied speakers from a digital audio source and combines an efficient Class-D output stage with integrated digital audio processing. Its digital input architecture supports programmable speaker EQ and DRC, while the open-loop design gives the system designer control over the signal chain and processing configuration. According to the verified TI product and distributor information, the TAS5707PHP provides a two-channel stereo output solution for compact consumer, communication, and embedded audio systems where efficiency, digital control, and speaker-driver capability are important design priorities. A Class-D audio power amplifier is a switching power amplifier that converts a digital or analog audio input into a high-efficiency speaker drive signal. Compared with a linear audio amplifier, the Class-D architecture reduces the amount of power dissipated by the output devices, which is valuable in portable and space-constrained equipment. The TAS5707PHP includes integrated audio processing functions that help tailor the output for speaker characteristics and system volume requirements. This combination of digital input, programmable processing, and a 20-W stereo output makes the device useful in speakers, sound bars, television equipment, and other systems requiring local amplification of a digital audio stream. The verified product description identifies the TAS5707PHP as a 20-W stereo digital audio power amplifier with speaker EQ and DRC. The stereo configuration allows two discrete audio channels to be processed and amplified in a single device, reducing the component count compared with separate mono amplifier channels. The open-loop architecture is also important because it provides a defined signal path that can be integrated with an external audio processor or system controller. The device therefore serves both as a power stage and as a digitally controlled audio subsystem element. The main engineering tradeoff is that the design must be validated for speaker impedance, power limitations, thermal conditions, and the specific digital audio configuration. The manufacturer product page identifies TAS5707PHP as not recommended for new designs, so it should be selected primarily for existing designs, legacy platforms, or qualified repair and production situations rather than as the default choice for a new product. The 48-pin HTQFP (PHP) package also requires a PCB footprint and land pattern that match the manufacturer package drawing. TAS5707PHP can be used in compact stereo speakers, television or monitor audio, communication terminals, portable equipment, and other embedded audio products where two amplified channels are needed. Digital audio sources can feed the amplifier through its digital input, allowing EQ and DRC to be configured in the digital processing domain. Designers should confirm the required sample rate, audio-word format, channel count, speaker impedance, power target, and control configuration against the manufacturer datasheet before layout or firmware development. This product page consolidates the verified TI product description, distributor package information, pricing reference, lifecycle indication, and practical application guidance for engineers evaluating TAS5707PHP. It emphasizes the distinctions that affect a real replacement decision: the 20-W stereo Class-D output, digital-input architecture, integrated speaker EQ and DRC, 48-pin HTQFP (PHP) package, and the manufacturer's not-recommended-for-new-designs status.

RFQ İletişim
TAS5708PHP - 20W Stereo Class-D Audio Amplifier | Texas Instruments
TAS5708PHP

TAS5708PHP - 20W Stereo Class-D Audio Amplifier | Texas Instruments

The Texas Instruments TAS5708PHP is a 20 W stereo digital Class-D audio power amplifier with an I2S input, closed-loop feedback, speaker equalization, and dynamic range control, housed in a 48-pin HTQFP (PHP) package. It operates from a 10 V to 26 V supply and is designed to drive stereo bridge-tied speakers with 20.2 W per channel. A digital Class-D audio power amplifier is a power-management IC that accepts digital audio samples and uses internal switching and feedback circuitry to deliver power to loudspeakers. The Class-D topology belongs to the switching-amplifier hierarchy rather than conventional linear amplifiers, improving efficiency while the integrated digital signal path controls volume, equalization, and speaker dynamics. The TAS5708 provides a 32-bit datapath, on-chip dynamic range control, and speaker equalization. Its digital input avoids the prescaling requirements associated with some older audio amplifiers and preserves signal integrity while processing audio. Closed-loop feedback is specifically identified for this device, providing a defined relationship between the amplifier output and the commanded speaker drive. The integrated processing functions reduce the need for separate software or analog signal-conditioning blocks in consumer audio equipment. Dynamic range control can maintain perceived loudness while reducing distortion or clipping, while speaker equalization can compensate for acoustic and enclosure response differences. Exact filter coefficients, configuration registers, protection thresholds, and thermal limits must be confirmed in the manufacturer datasheet before implementation. Typical uses include compact stereo speakers, multimedia speaker systems, Bluetooth speaker enclosures, soundbars, consumer television audio, and other powered speaker products. The 10 V to 26 V supply range suits systems using an external Class-D-compatible supply while keeping the amplifier integrated with digital audio processing. A key design consideration is that the exposed thermal pad and output-filter layout must follow the manufacturer's reference design. Power loss depends on supply voltage, output power, modulation method, and filter efficiency, so thermal analysis should use the worst-case audio waveform rather than only a continuous sine-wave condition. This product record combines manufacturer and distributor information with verified same-family alternatives, package-aware comparisons, and practical implementation guidance. It distinguishes confirmed specifications from values that require engineers to consult the full datasheet or design-support resources.

RFQ İletişim
TAS5709PHP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5709PHP

TAS5709PHP - 20W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5709PHP is a 20 W stereo, 2-channel Class-D digital audio power amplifier with an 8 V to 24 V supply, digital input, speaker equalization, and dynamic range control, housed in a 48-pin HTQFP (PHP) package. A Class-D audio power amplifier is a switching power stage that converts digital audio signals into high-efficiency bridge-tied speaker drive. Within the broader hierarchy, the TAS5709PHP belongs to the digital audio amplifier class, then audio amplifiers, then amplifier ICs and analog/mixed-signal semiconductors. Its digital input and integrated processing allow a host processor to deliver audio directly without requiring a separate analog-to-digital converter or pre-amplifier stage. The device provides 20 W stereo output, operates from an 8 V to 24 V supply, and supports digital audio input through a serial interface. On-chip speaker EQ and dynamic range control provide programmable acoustic functions before the signal reaches the power stages. These functions make the amplifier useful where cabinet, speaker, and source characteristics require system-level audio adjustment rather than fixed analog gain alone. Technically, the TAS5709PHP integrates a digital signal-processing path with two Class-D output channels designed to drive stereo bridge-tied speakers. The verified manufacturer information identifies the device as an open-loop Class-D amplifier, meaning the IC is intended for use with external closed-loop feedback circuitry. System designers must therefore account for the feedback network, filtering requirements, output configuration, and protection strategy when developing the speaker-amplifier stage. Typical uses include stereo speaker amplification in consumer electronics, audio racks, television systems, and embedded digital-audio products. Its digital input can simplify connections to audio processors, MPEG decoders, and digital audio sources, while integrated EQ and dynamic range control can reduce the amount of host-side processing required for common speaker-management functions. A key design consideration is the relationship between supply voltage, speaker impedance, thermal dissipation, and Class-D output filtering. The amplifier should be placed near the speaker connectors, with its power and ground system designed to minimize switching noise and output-stage instability. Verify the external feedback and filter topology against the manufacturer datasheet before production use. This page consolidates verified manufacturer and distributor information, practical design guidance, and clearly qualified replacement considerations. It also separates confirmed same-family parts from candidates whose pin compatibility cannot be established from the supplied web evidence, helping engineers make sourcing decisions without treating merely similar devices as true drop-in replacements.

RFQ İletişim
TAS5709PHPR - 20W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)
TAS5709PHPR

TAS5709PHPR - 20W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments TAS5709PHPR is a 20 W stereo, 2-channel Class-D digital audio power amplifier with an 8 V to 24 V supply, digital input, speaker equalization, and dynamic range control, housed in a 48-pin HTQFP (PHP) package. A Class-D audio power amplifier is a switching power stage that converts digital audio signals into high-efficiency bridge-tied speaker drive. Within the broader hierarchy, the TAS5709PHPR belongs to the digital audio amplifier class, then audio amplifiers, then amplifier ICs and analog/mixed-signal semiconductors. Its digital input and integrated processing allow a host processor to deliver audio directly without requiring a separate analog-to-digital converter or pre-amplifier stage. The device provides 20 W stereo output, operates from an 8 V to 24 V supply, and supports digital audio input through a serial interface. On-chip speaker EQ and dynamic range control provide programmable acoustic functions before the signal reaches the power stages. These functions make the amplifier useful where cabinet, speaker, and source characteristics require system-level audio adjustment rather than fixed analog gain alone. Technically, the TAS5709PHPR integrates a digital signal-processing path with two Class-D output channels designed to drive stereo bridge-tied speakers. The verified manufacturer information identifies the device as an open-loop Class-D amplifier, meaning the IC is intended for use with external closed-loop feedback circuitry. System designers must therefore account for the feedback network, filtering requirements, output configuration, and protection strategy when developing the speaker-amplifier stage. Typical uses include stereo speaker amplification in consumer electronics, audio racks, television systems, and embedded digital-audio products. Its digital input can simplify connections to audio processors, MPEG decoders, and digital audio sources, while integrated EQ and dynamic range control can reduce the amount of host-side processing required for common speaker-management functions. A key design consideration is the relationship between supply voltage, speaker impedance, thermal dissipation, and Class-D output filtering. The amplifier should be placed near the speaker connectors, with its power and ground system designed to minimize switching noise and output-stage instability. Verify the external feedback and filter topology against the manufacturer datasheet before production use. This page consolidates verified manufacturer and distributor information, practical design guidance, and clearly qualified replacement considerations. It also separates confirmed same-family parts from candidates whose pin compatibility cannot be established from the supplied web evidence, helping engineers make sourcing decisions without treating merely similar devices as true drop-in replacements.

RFQ İletişim
TAS5710PHP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5710PHP

TAS5710PHP - 20W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5710PHP is a 20 W stereo, digital-input, closed-loop Class-D audio amplifier with speaker equalization and 2-band dynamic range control, housed in a 48-pin HTQFP package measuring 7 x 7 mm. The device operates from a 10 V to 26 V power-supply range and is designed to drive stereo bridge-tied speakers through its integrated digital audio processing and class-D output stages. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to deliver speaker power efficiently. Compared with a linear audio amplifier, this approach reduces the amount of power dissipated as heat in the output stage. A digital-input device accepts encoded audio data rather than an analog line-level signal, allowing software-defined volume, equalization, and dynamic-range-control functions to be applied before the signal reaches the power-output stage. The TAS5710PHP combines two stereo output channels, digital signal processing, and closed-loop output feedback in one package. Its identified 20 W output capability is suitable for compact consumer-audio equipment where space and power efficiency matter. The integrated equalization function can shape speaker response, while the 2-band DRC can reduce unwanted level variation. Exact processing coefficients, gain settings, output-power conditions, and thermal limits depend on the manufacturer configuration and test conditions. The digital input architecture makes the amplifier suitable for systems in which a host processor or digital audio codec supplies I2S-compatible data. Designers can centralize mixing, source selection, volume control, and tone processing in software, while the TAS5710PHP converts the digital stream into a bridge-tied Class-D speaker drive. The closed-loop topology is intended to improve output behavior by using feedback to correct the delivered bridge-tied voltage. Typical uses include powered speakers, soundbars, compact stereo systems, wireless speakers, displays, and consumer audio products with digital audio sources. The 48-pin HTQFP package offers many connections for power, ground, digital audio, configuration, feedback, and output stages, but the complete exposed-pad land pattern and thermal-management requirements must be followed exactly. Layout is as important as the logical signal path. Place the decoupling capacitors close to their associated supply pins, provide a low-impedance ground return for the power stage, and route the sensitive digital, clock, and feedback connections away from switching-node currents. The exposed thermal pad must be connected to the ground plane with adequate copper and vias; otherwise the 20 W class can create a substantial thermal burden even though the amplifier is electrically efficient. This page consolidates the verified manufacturer and distributor information, distinguishes documented capabilities from unspecified parameters, and provides application and design guidance that should be checked against the complete manufacturer datasheet before schematic capture or PCB release.

RFQ İletişim
TAS5711PHP - 20W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)
TAS5711PHP

TAS5711PHP - 20W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments TAS5711PHP is a 20 W digital-input, open-loop Class-D audio power amplifier for stereo bridge-tied speakers, with 8 V to 26 V PVDD operation, 2.1-channel support, equalization, dynamic range control, and a 48-pin HTQFP package measuring 7 mm by 7 mm. Its digital signal path supports up to two discrete audio channels, while its integrated processing is designed for use with digital audio processors and MPEG decoders. A Class-D audio amplifier is a switching power amplifier that uses efficient transistor output stages to drive speakers through LC filter networks. It belongs to the broader class of audio amplifiers, power amplifiers, and analog and mixed-signal semiconductors. Compared with a linear amplifier, the TAS5711 family is intended to reduce power dissipation while delivering high output power for portable consumer-audio equipment, soundbars, compact televisions, and other embedded audio systems. The verified manufacturer data identifies the TAS5711 as a 20 W stereo amplifier operating from an 8 V to 26 V supply and reaching up to 90% efficiency. It provides digital audio input, programmable channel routing, AD and BD filter-mode support, EQ, DRC, and 2.1 mode. The verified datasheet search result also lists SNR of 106 dB, A-weighted, and describes bridge-tied-load operation for stereo speakers. The device accepts a wide range of input data and data rates through its serial digital interface. This makes the signal path suitable for systems where audio is already processed by a digital audio codec, decoder, application processor, or MPEG source. The internal programmable path can route two discrete channels and supports audio processing functions without requiring a separate analog preamplifier for those functions. Typical uses include stereo speaker drive, compact 2.1 speaker systems, consumer-audio equipment, soundbar amplification, and embedded audio products requiring efficient digital power amplification. The supplied PVDD range provides design flexibility for battery-powered and external-amplifier architectures, although actual speaker output depends on supply voltage, load impedance, thermal conditions, and filter design. Designers should follow the manufacturer datasheet for the exact pin functions, exposed-pad connection, LC filter values, thermal layout, digital interface timing, and power-supply decoupling. Because the part is a Class-D output stage, speaker outputs require the specified external filtering network. PCB placement should keep the power-loop area small, provide adequate copper for thermal dissipation, and route sensitive digital signals away from output switching nodes. This product record consolidates the verified manufacturer description, distributor identification, package information, and practical replacement-search results. It is intended to support design review, sourcing, and datasheet discovery; verify the current datasheet and part-status notices before committing a production design.

RFQ İletişim
TAS5711PHPR - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5711PHPR

TAS5711PHPR - 20W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5711PHPR is a 20 W digital-input, open-loop Class-D audio power amplifier for stereo bridge-tied speakers, with 8 V to 26 V PVDD operation, 2.1-channel support, equalization, dynamic range control, and a 48-pin HTQFP package measuring 7 mm by 7 mm. Its digital signal path supports up to two discrete audio channels, while its integrated processing is designed for use with digital audio processors and MPEG decoders. A Class-D audio amplifier is a switching power amplifier that uses efficient transistor output stages to drive speakers through LC filter networks. It belongs to the broader class of audio amplifiers, power amplifiers, and analog and mixed-signal semiconductors. Compared with a linear amplifier, the TAS5711 family is intended to reduce power dissipation while delivering high output power for portable consumer-audio equipment, soundbars, compact televisions, and other embedded audio systems. The verified manufacturer data identifies the TAS5711 as a 20 W stereo amplifier operating from an 8 V to 26 V supply and reaching up to 90% efficiency. It provides digital audio input, programmable channel routing, AD and BD filter-mode support, EQ, DRC, and 2.1 mode. The verified datasheet search result also lists SNR of 106 dB, A-weighted, and describes bridge-tied-load operation for stereo speakers. The device accepts a wide range of input data and data rates through its serial digital interface. This makes the signal path suitable for systems where audio is already processed by a digital audio codec, decoder, application processor, or MPEG source. The internal programmable path can route two discrete channels and supports audio processing functions without requiring a separate analog preamplifier for those functions. Typical uses include stereo speaker drive, compact 2.1 speaker systems, consumer-audio equipment, soundbar amplification, and embedded audio products requiring efficient digital power amplification. The supplied PVDD range provides design flexibility for battery-powered and external-amplifier architectures, although actual speaker output depends on supply voltage, load impedance, thermal conditions, and filter design. Designers should follow the manufacturer datasheet for the exact pin functions, exposed-pad connection, LC filter values, thermal layout, digital interface timing, and power-supply decoupling. Because the part is a Class-D output stage, speaker outputs require the specified external filtering network. PCB placement should keep the power-loop area small, provide adequate copper for thermal dissipation, and route sensitive digital signals away from output switching nodes. This product record consolidates the verified manufacturer description, distributor identification, package information, and practical replacement-search results. It is intended to support design review, sourcing, and datasheet discovery; verify the current datasheet and part-status notices before committing a production design.

RFQ İletişim
TAS5713PHP - 25W Stereo Class-D Amplifier | TI
TAS5713PHP

TAS5713PHP - 25W Stereo Class-D Amplifier | TI

The Texas Instruments TAS5713PHP is a 25 W stereo digital-input Class-D audio amplifier with equalization and dynamic range control, housed in a 48-HTQFP package measuring 7 mm by 7 mm. It accepts an 8 V to 26 V supply and processes up to two discrete audio channels through one serial data input. The device is designed to drive stereo bridge-tied speakers from digital audio processors and MPEG decoders. A Class-D audio amplifier is a switching power amplifier that efficiently converts digital audio signals into differential speaker outputs. Within the semiconductor hierarchy, it belongs to the amplifier IC family, the audio amplifier IC subcategory, and the broader power-management and signal-processing ecosystem. The TAS5713PHP combines digital signal processing, speaker drive, and integrated audio features in one package. The principal specifications include 25 W output capability, two-channel stereo operation, an 8 V to 26 V supply range, digital input, integrated equalization, and dynamic range control. Its 48-pin HTQFP package supports compact PCB integration while providing separate connections for power, ground, digital audio data, clock signals, and differential speaker outputs. The exact output-power conditions and thermal limits must be confirmed from the manufacturer datasheet. Internally, the TAS5713PHP uses a serial digital-audio input and a programmable data path to route two channels into the stereo output stage. Equalization and dynamic range control are integrated into the signal-processing chain, reducing the need for separate software or hardware blocks in many audio systems. Its Class-D output architecture is intended for efficient bridge-tied speaker drive rather than conventional analog power-amplifier output stages. Typical uses include compact stereo speakers, soundbars, display audio systems, set-top equipment, portable audio products, and other consumer electronics that accept digital audio data. A digital audio interface or processor can feed the serial input, while the two Class-D outputs connect to left and right speakers. System-level thermal design remains important because the available 25 W rating depends on supply voltage, load conditions, and PCB copper. The primary design consideration is to preserve clean power and signal paths around the amplifier. Short output connections, adequate input and output decoupling, stable supply routing, and thermal copper help maintain audio performance. Speaker impedance and power limits must be taken directly from the manufacturer documentation rather than inferred from the headline 25 W rating. This product data combines the verified 25 W stereo Class-D configuration, 8 V to 26 V supply range, 48-HTQFP package, digital processing features, distributor pricing, availability information, and practical integration guidance. It also distinguishes verified facts from parameters that still require direct confirmation in the manufacturer datasheet.

RFQ İletişim
TAS5715PHP - 25W Stereo Class-D Audio Amplifier | Texas Instruments
TAS5715PHP

TAS5715PHP - 25W Stereo Class-D Audio Amplifier | Texas Instruments

Texas Instruments TAS5715PHP is a 25 W stereo Class-D digital audio power amplifier with an 8 V to 26 V PVDD range, digital input, integrated speaker EQ, dynamic range control, high-pass filtering, and headphone PWM outputs in a 48-pin HTQFP (PHP) package measuring 7 mm by 7 mm. A Class-D audio power amplifier is an efficient switching power stage that drives stereo bridge-tied speakers using digital input data. Within the broader semiconductor hierarchy, the TAS5715PHP is a digital-input audio power amplifier, a member of the Class-D amplifier family, and an audio amplifier IC used in professional and consumer audio power-management systems. Its 48-pin surface-mount HTQFP package supports dense integration on audio amplifier boards. The verified product information specifies 25 W output into an 8 ohm load from an 18 V supply, together with support for 50 W operation in parallel bridge-tie load, or PBTL, mode with a 4 ohm load. The device accepts digital audio data for up to two discrete channels, allowing a digital audio processor or MPEG decoder to feed the stereo output stages without separate analog-to-digital conversion. The TAS5715 combines speaker signal processing with power amplification. Integrated features include equalization, dynamic range control, high-pass filtering, and DC protection. Headphone PWM outputs add a second use case beyond loudspeaker drive, while efficient Class-D operation reduces the heat normally associated with linear audio output stages. The open-loop architecture provides digital control of the audio signal path rather than relying only on conventional analog feedback. Typical applications include powered stereo speakers, compact consumer audio systems, multimedia equipment, sound bars, and digital-audio source products. Its serial digital input works naturally with digital audio processors and MPEG decoders, while the 25 W stereo rating targets conventional 8 ohm speaker loads. The 50 W PBTL capability provides additional flexibility for suitable 4 ohm loads when the amplifier, thermal design, and board layout support that operating mode. Power-supply and thermal layout are critical because Class-D output current and switching losses produce heat in the HTQFP package. The exposed-pad area and surrounding PCB copper must be designed for effective heat transfer, and speaker outputs must not be connected to ground or chassis. Input routing, power ground separation, and output-filter selection also require careful layout to preserve audio performance and suppress unwanted switching artifacts. This product page consolidates verified manufacturer and distributor information, structured drop-in alternatives, parameter comparisons, and practical design guidance. It distinguishes sourced specifications from unavailable detailed electrical data, helping engineers locate the official datasheet, evaluate replacement options, and plan a robust digital Class-D audio-amplifier implementation.

RFQ İletişim