Ürünler (44.000+)

TAS5715PHPR - 25W Stereo Class-D Audio Amplifier | Texas Instruments (Tape & Reel)
TAS5715PHPR

TAS5715PHPR - 25W Stereo Class-D Audio Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments TAS5715PHPR is a 25 W stereo Class-D digital audio power amplifier with an 8 V to 26 V PVDD range, digital input, integrated speaker EQ, dynamic range control, high-pass filtering, and headphone PWM outputs in a 48-pin HTQFP (PHP) package measuring 7 mm by 7 mm. A Class-D audio power amplifier is an efficient switching power stage that drives stereo bridge-tied speakers using digital input data. Within the broader semiconductor hierarchy, the TAS5715PHPR is a digital-input audio power amplifier, a member of the Class-D amplifier family, and an audio amplifier IC used in professional and consumer audio power-management systems. Its 48-pin surface-mount HTQFP package supports dense integration on audio amplifier boards. The verified product information specifies 25 W output into an 8 ohm load from an 18 V supply, together with support for 50 W operation in parallel bridge-tie load, or PBTL, mode with a 4 ohm load. The device accepts digital audio data for up to two discrete channels, allowing a digital audio processor or MPEG decoder to feed the stereo output stages without separate analog-to-digital conversion. The TAS5715 combines speaker signal processing with power amplification. Integrated features include equalization, dynamic range control, high-pass filtering, and DC protection. Headphone PWM outputs add a second use case beyond loudspeaker drive, while efficient Class-D operation reduces the heat normally associated with linear audio output stages. The open-loop architecture provides digital control of the audio signal path rather than relying only on conventional analog feedback. Typical applications include powered stereo speakers, compact consumer audio systems, multimedia equipment, sound bars, and digital-audio source products. Its serial digital input works naturally with digital audio processors and MPEG decoders, while the 25 W stereo rating targets conventional 8 ohm speaker loads. The 50 W PBTL capability provides additional flexibility for suitable 4 ohm loads when the amplifier, thermal design, and board layout support that operating mode. Power-supply and thermal layout are critical because Class-D output current and switching losses produce heat in the HTQFP package. The exposed-pad area and surrounding PCB copper must be designed for effective heat transfer, and speaker outputs must not be connected to ground or chassis. Input routing, power ground separation, and output-filter selection also require careful layout to preserve audio performance and suppress unwanted switching artifacts. This product page consolidates verified manufacturer and distributor information, structured drop-in alternatives, parameter comparisons, and practical design guidance. It distinguishes sourced specifications from unavailable detailed electrical data, helping engineers locate the official datasheet, evaluate replacement options, and plan a robust digital Class-D audio-amplifier implementation.

RFQ İletişim
TAS5716PAP - 20W Stereo Class-D Audio Amplifier | Texas Instruments
TAS5716PAP

TAS5716PAP - 20W Stereo Class-D Audio Amplifier | Texas Instruments

Texas Instruments TAS5716PAP is a 20 W stereo digital-input Class-D audio power amplifier with speaker EQ, dynamic range control, and bass boost, housed in a 64-pin HTQFP (PAP) package measuring 10 mm by 10 mm. It operates from a 10 V to 26 V supply and supports stereo bridged-tied speaker output. A Class-D audio amplifier is a switching power amplifier whose output stage operates between conductive and nonconductive states instead of continuously biasing a conventional linear output transistor. In the electronic-component hierarchy, the TAS5716PAP belongs to the Class-D amplifier family, which is part of audio amplifiers, amplifier ICs, and power-management semiconductors. Its digital architecture reduces output-stage dissipation compared with a linear amplifier of comparable output power. The TAS5716PAP combines two serial-data inputs with digital signal processing capabilities. According to the Texas Instruments product page, the amplifier includes speaker EQ, DRC, and bass boost, allowing system designers to shape playback characteristics without implementing all of that processing in an upstream audio codec or digital signal processor. The verified data also identifies support for up to four discrete audio channels, making the device suitable for multi-zone or multi-speaker arrangements when the host processor supplies suitable digital audio streams. The device delivers up to 20 W stereo output from a 10 V to 26 V supply. Its 64-pin HTQFP package provides separate connections for digital audio, control, power, ground, and output-stage functions. The verified component listing identifies an 8 Ω maximum load resistance, and a comparison source reports a maximum power dissipation of 2890 mW. These values should be verified against the complete manufacturer datasheet for the selected speaker impedance, supply voltage, channel configuration, and output-power operating condition. Typical uses include television and display audio, compact stereo speaker systems, wireless speakers, headphones, microphones, and other consumer audio products. The digital input is particularly useful where an I2S-compatible audio processor can supply standard-rate serial audio and system control. Stereo operation can use bridged-tied outputs, while the capability to process discrete channels supports more flexible multi-speaker implementations. A critical design consideration is Class-D output filtering and PCB layout. The switching outputs require a correctly designed low-pass filter before the speaker connection, while the power-supply network must handle high-frequency ripple current. Designers should also confirm channel population, thermal margin, speaker impedance, and the supported digital audio format before releasing production hardware. This page consolidates the verified manufacturer and distributor information into an engineer-oriented comparison, application guide, pricing-data availability note, and design checklist. It also clearly identifies where complete pin, electrical, compliance, and alternative-part data must be obtained from the manufacturer datasheet rather than inferred from search snippets.

RFQ İletişim
TAS5717PHP - 10W Stereo Class-D Amplifier | Texas Instruments
TAS5717PHP

TAS5717PHP - 10W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5717PHP is a 10 W stereo digital-input Class-D audio power amplifier with a 4.5 V to 26 V supply range, integrated capacitor-free headphone output, and a 48-pin HTQFP (PHP) package. It accepts one serial digital audio input and supports two discrete audio channels for efficient bridge-tied speaker drive. The device combines the TAS5717 stereo power-amplifier function with TI DirectPath ground-centered headphone output technology. A Class-D audio amplifier is a switching power amplifier that uses transistor output stages to deliver high audio power efficiently. In bridge-tied-load operation, each output contributes to the voltage across the speaker. This architecture belongs to the broader power-amplifier and audio-IC hierarchy, where efficiency, thermal performance, output-filter requirements, and signal-path integration are central design considerations. Principal device features include 2 x 10 W stereo output capability, digital audio input, a 4.5 V to 26 V operating supply range, and integrated capacitor-free headphone outputs. The verified specifications also report THD+N of 0.13% at 1 W into an 8-ohm load with PVDD at 8 V. A single serial-data input supports programmable routing of two discrete audio channels, making the device suitable for systems receiving audio from digital processors, MPEG decoders, and other digital audio sources. The amplifier's integrated digital signal path reduces the need for a separate analog input interface, while its headphone stage offers a practical transition between loudspeaker and headphone outputs in compact consumer equipment. The PHP package provides 48 pins and a 7 x 7 mm body. Because no verified mechanical drawing, pin table, exposed-pad recommendation, or complete power-dissipation table was included in the supplied data, those implementation details must be confirmed in the manufacturer datasheet before layout is released. Typical uses include powered speakers, multimedia speaker systems, compact consumer audio products, and equipment requiring digital audio input plus both stereo loudspeaker and headphone outputs. Because the loudspeaker interface is a bridge-tied load, neither output should be referenced to system ground without an appropriate coupling or isolation arrangement. The integrated headphone output may reduce the external component count relative to designs using a separate headphone amplifier. A key design consideration is power-rail planning: the verified 4.5 V to 26 V range must cover startup, load-transient, and supply-noise requirements without exceeding the device limits. PCB designers should follow the manufacturer's land pattern, exposed-pad, thermal, output-filter, and decoupling guidance exactly. Speaker and headphone outputs also require EMI and EMI-risk review because Class-D switching currents can couple into sensitive analog or radio-frequency circuitry. This page consolidates the verified manufacturer and distributor information with structured specifications, purchase-intent guidance, application analysis, and honest replacement criteria. It also distinguishes confirmed TAS5717PHP characteristics from parameters that still require datasheet-level verification, helping engineers avoid treating generic Class-D amplifier data as device-specific evidence.

RFQ İletişim
TAS5719PHP - 15W Stereo Class-D Amplifier | Texas Instruments
TAS5719PHP

TAS5719PHP - 15W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5719PHP is a 15 W stereo, 4.5 V to 26 V digital-input Class-D audio amplifier with integrated capacitor-free headphone amplifier, housed in a 48-pin HTQFP (PHP) package measuring 7 mm by 7 mm. It supports two discrete audio channels through one serial data input and is designed to drive stereo bridge-tied speakers. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to deliver speaker output more efficiently than a conventional linear audio amplifier. The hierarchy is digital audio power amplifier to Class-D amplifier to audio amplifier IC, while the TAS5719 also integrates headphone-driver and signal-processing functions. This combination supports compact consumer and industrial audio systems requiring digital sources and analog speaker outputs. The principal features are 2 x 15 W stereo output capability, a 4.5 V to 26 V power-supply range, digital audio input, and an integrated capacitor-free headphone amplifier. Its 48-pin HTQFP package supports surface-mount assembly and thermal management through the exposed thermal pad. The device accepts wide-ranging input data and data rates for straightforward connection to digital audio processors and MPEG decoders. Internally, one serial data input supplies two independently routable discrete audio channels. The digital data path allows channels to be processed before conversion to the power-amplifier stage, reducing the need for a separate analog preamplifier in compatible systems. The integrated capacitor-free headphone path provides an additional low-power analog output function without requiring the traditional series output capacitors used with many headphone drivers. Typical uses include compact stereo speakers, audio docking stations, consumer television equipment, portable entertainment products, and industrial sound systems. The 15 W per-channel output rating is appropriate for small bookshelf speakers and multimedia speaker systems, while the 4.5 V to 26 V supply range accommodates systems powered from external adapters or higher-voltage industrial rails. PCB design should prioritize the exposed thermal pad, clean speaker-output routing, stable supply bypassing, and careful return-current management around the switching power stage. Speaker outputs carry high-frequency PWM energy, so keep sensitive audio inputs and external microphone circuitry away from the output nets. Verify thermal performance and EMI behavior in the final enclosure and load configuration. This page consolidates the verified manufacturer and distributor information, same-package family alternatives, package details, sourcing guidance, and application-specific design considerations. It distinguishes documented electrical facts from parameters that still require confirmation from the manufacturer datasheet before a new PCB or production release.

RFQ İletişim
TAS5721DCA - 10W Stereo 2.1 Class-D Amplifier | Texas Instruments
TAS5721DCA

TAS5721DCA - 10W Stereo 2.1 Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5721DCA is a 10 W stereo, 8 V to 26.4 V digital-input, open-loop Class-D audio amplifier with 2.1-channel support and headphone/line-driver capability, housed in a 48-pin HTSSOP DCA package. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to deliver speaker output efficiently. It belongs to the amplifier IC hierarchy, specifically the digital-input audio amplifier and power-amplifier classes. Unlike a conventional linear output stage, its switching architecture is intended to reduce amplifier dissipation while supporting compact, high-output audio systems. The device supports stereo bridge-tied-load speaker configurations, 2.1 systems containing two satellite speakers and one subwoofer, and parallel bridge-tied-load arrangements. Its digital audio input makes it suitable for systems using a digital audio source, while the open-loop architecture provides a distinct integration path for designs that manage gain or feedback externally. Key features include 10 W stereo output capability, an 8 V to 26.4 V supply range, digital input, support for 2.0 and 2.1 speaker systems, and integrated headphone or line-driver functionality. The 48-pin HTSSOP package provides the required connections for audio inputs, speaker outputs, control signals, power, and ground. The listed operating-temperature range is 0°C to 85°C. Typical uses include compact stereo speakers, multimedia speaker systems, sound bars, active subwoofer combinations, and other consumer audio products requiring efficient digital amplification. The 2.1 support is particularly useful when a product must combine left and right satellite speakers with a subwoofer in one amplifier solution. Designers should verify speaker impedance, power dissipation, thermal performance, decoupling, and output routing against the manufacturer datasheet before layout. The HTSSOP exposed-pad package also requires careful PCB thermal design so heat can spread into the board rather than concentrating beneath the device. This page combines verified manufacturer and distributor facts with explicit data gaps, practical application guidance, parameter comparisons, and sourcing links. It distinguishes confirmed specifications from information that still requires datasheet verification instead of presenting unverified assumptions as guaranteed performance.

RFQ İletişim
TAS5725RGZR Audio Amplifier IC | Texas Instruments
TAS5725RGZR

TAS5725RGZR Audio Amplifier IC | Texas Instruments

The Texas Instruments TAS5725RGZR is an amplifier integrated circuit identified by the manufacturer as part of the TAS5725 family and offered under the RGZ ordering suffix. It is intended for electronic designs that require an integrated audio amplification function. The RGZ package type, pin count, channel configuration, voltage ratings, output capability, and thermal limits are identified in the Texas Instruments manufacturer datasheet, while the verified product record confirms the exact orderable MPN TAS5725RGZR. An amplifier IC is a semiconductor that increases the voltage or power level of an audio signal. In an audio signal chain, it may provide gain, drive a speaker or other load, and combine multiple analog functions into one component. Depending on the implementation, this device category can serve consumer audio, communications, industrial control, automotive, or embedded systems. Its suitability depends on matching supply voltage, output configuration, load impedance, signal format, thermal environment, and package constraints to the design requirements. The primary selection criteria are the device's documented operating voltage, output power, channel count, input architecture, control interface, and protection features. Designers should also evaluate quiescent current, amplifier efficiency, distortion, noise, thermal resistance, and operating-temperature limits. These electrical and environmental characteristics determine whether the IC can drive the intended load without clipping, overheating, exceeding current limits, or introducing unacceptable signal degradation. TAS5725RGZR should be treated as a dedicated audio amplifier rather than a general-purpose signal amplifier. The exact internal architecture and supported operating modes are defined by the manufacturer datasheet. Before schematic capture, confirm the supply pins, ground connections, control pins, analog input path, output path, exposed thermal pad, and decoupling requirements directly against the pin-description table. Use those same functions to define test points and the PCB land pattern. Typical design opportunities include powered speakers, soundbars, television audio, portable media equipment, communications terminals, and compact industrial audio modules. In each case, the amplifier must match the chosen speaker impedance and power rating. If the amplifier operates in bridge-tied mode, confirm that the output architecture, supply level, and thermal performance support the intended load. Digital audio systems also require checking whether the IC accepts analog signals directly or requires an external codec. Layout is critical because audio amplifiers combine high-current outputs with sensitive input and control signals. Keep the power and ground paths short, place required bypass capacitors close to their pins, provide adequate exposed-pad thermal relief, and route output returns without sharing noisy switching-current paths with input references. Confirm all minimum copper, thermal-via, and output-loop recommendations in the Texas Instruments layout guidance before release. This page organizes the exact TAS5725RGZR identity, verified source records, application-selection guidance, and practical design checks. It also distinguishes documented sourcing information from the datasheet values an engineer must confirm before schematic and layout release, supporting faster component selection without hiding unresolved engineering constraints.

RFQ İletişim
TAS5725RGZT - 20W Class-D Audio Amplifier | Texas Instruments
TAS5725RGZT

TAS5725RGZT - 20W Class-D Audio Amplifier | Texas Instruments

The Texas Instruments TAS5725RGZT is a 20 W Class-D audio power amplifier IC supplied in a surface-mount RGZ tape-and-reel package. It is designed for compact audio systems that require efficient digital power amplification while maintaining a small component footprint. The product listing identifies the device as a linear audio amplifier IC from Texas Instruments. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to control energy delivered to a loudspeaker. Compared with conventional linear audio output stages, the Class-D architecture can reduce power dissipation and heat generation, making it useful in consumer audio, automotive audio, communications equipment, and powered speaker systems. The exact channel configuration, modulation method, and electrical limits are defined by the manufacturer datasheet. The TAS5725RGZT is associated with a 20 W audio output class and closed-loop feedback operation. Closed-loop feedback is intended to correct output distortion and voltage variation by measuring the amplifier output and adjusting the drive stage. Digital audio input support can also help reduce analog signal-chain complexity when the surrounding system uses a digital audio source, although connector format, data format, and control-interface details must be confirmed against the pin description and application information. The RGZ ordering variant is supplied on tape and reel for automated surface-mount assembly. A tape-and-reel format supports high-volume pick-and-place production while protecting the exposed package leads from mechanical handling. Package dimensions, exposed-pad construction, pin orientation, and recommended land pattern require confirmation from the Texas Instruments package drawing before PCB release. Typical uses include compact powered speakers, soundbars, automotive cabin-audio systems, communication speakers, and portable or networked audio products. In these systems, the amplifier converts a digital audio stream into a high-current drive signal for the loudspeaker. Designers should size the power supply for the amplifier load, maintain adequate copper area for thermal conduction, and filter switched-node energy before it reaches sensitive analog circuitry. The main design consideration is ensuring that the power stage, speaker load, layout, and thermal design operate together. Speaker impedance and frequency determine required output power and current, while PCB copper and enclosure heat dissipation limit sustainable output. Place input, power, and ground connections according to the manufacturer reference layout, and validate EMC performance before a production release. This page organizes the available TAS5725RGZT product information, sourcing questions, package guidance, and engineering considerations. For an exact electrical or pin-level decision, use the Texas Instruments datasheet, pin table, typical application circuit, and package drawing as the controlling references.

RFQ İletişim
TAS5727PHP - 25W Stereo Class-D Audio Amplifier | TI
TAS5727PHP

TAS5727PHP - 25W Stereo Class-D Audio Amplifier | TI

Texas Instruments TAS5727PHP is a 25 W stereo Class-D digital audio power amplifier with a supply range of 8 V to 26 V, housed in a 48-pin HTQFP (PHP) package measuring 7 mm by 7 mm. It accepts digital audio input, supports bridge-tied-load speaker outputs, and integrates programmable speaker equalization and dynamic range control. The device can deliver 25 W into an 8 ohm load from a 20 V supply and can support 4 ohm loads in bridge-tied-load configurations. A Class-D audio power amplifier is a switching power amplifier whose output transistors operate at high frequency, allowing higher efficiency than a traditional linear amplifier. Within the broader hierarchy, TAS5727PHP is a digital-input audio power amplifier, a Class-D amplifier, an audio amplifier IC, and a power-management semiconductor designed to reproduce low-power digital audio signals at speaker-driving power levels. The primary features of TAS5727PHP include 25 W stereo output capability, an 8 V to 26 V PVDD range, digital signal input, integrated EQ and DRC, and low-RDS(ON) output stages that improve thermal performance. Its digital signal path can accept multiple data rates and route two discrete audio channels, allowing integration with digital audio processors, MPEG decoders, and other source devices. The architecture combines a digital audio input interface with a high-efficiency Class-D output stage. BTL operation permits a speaker to be driven differentially between two output nodes, increasing useful voltage swing into the load. Because the amplifier uses an open-loop digital input architecture, its processing behavior is configured through the associated digital control and configuration method rather than conventional analog feedback around the power stage. Typical uses include powered speakers, compact stereo audio systems, soundbars, wireless speaker enclosures, home-theater equipment, and consumer products that require local amplification of a digital audio stream. The 48-pin surface-mount package supports compact layouts, while the low-RDS(ON) output design addresses heat dissipation in continuously operating audio equipment. Designers should account for the amplifier's thermal dissipation, power-supply current, speaker impedance, PCB copper area, and output-filter requirements. The 8 V to 26 V supply range leaves less headroom than higher-voltage power amplifiers, so supply planning is essential when driving 4 ohm loads or sustained high-level audio. This product page consolidates the verified manufacturer specifications, distributor sourcing information, same-package drop-in candidates, and practical design guidance into one engineering-focused reference for audio-product developers.

RFQ İletişim
TAS5731PHP - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5731PHP

TAS5731PHP - 20W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5731PHP is a 20 W stereo, 41 W mono, digital-input, open-loop Class-D audio amplifier with 2.1-channel support, supplied in a 48-pin HTQFP (PHP) package. It operates from an 8 V to 21.5 V analog power supply and accepts a 3.3 V digital supply. The device supports one or two output channels, allowing a single implementation to address stereo playback or a subwoofer-assisted 2.1 audio system. Its advertised efficiency can reach 90%. A Class-D audio amplifier is a switching power amplifier whose output stage rapidly switches between supply rails, producing a filtered full-bridge output for a speaker load. Within the electronics hierarchy, the TAS5731PHP belongs to the Class-D amplifier family, then to audio power amplifiers, then to amplifier ICs and power-management semiconductors. Its digital input architecture simplifies connection to digital audio processors and MPEG decoders while avoiding an analog input path. Key features include 20 W stereo output capability, 41 W mono output capability, an 8 V to 21.5 V supply range, and 90% efficiency. The manufacturer search data also identifies a 3.3 V digital supply requirement and a 70 mΩ output-device on-resistance. These characteristics suit compact consumer audio equipment where a high-efficiency amplifier can reduce heat generation relative to a linear amplifier operating from the same supply. The PHP package contains 48 pins and measures 7 mm by 7 mm. Its operating-temperature range is -40°C to 85°C. The Part-Pin-Value option refers to the open-loop digital amplifier configuration identified by Texas Instruments; detailed control, filtering, and mixer implementation therefore depend on the associated DSP and external circuit design rather than on a conventional analog gain-control network. Typical applications include stereo speaker systems, compact sound bars, home-theater equipment, active subwoofers, and 2.1-channel multimedia products. The 2.1 support can reduce the need for a separate amplifier when driving left, right, and subwoofer channels. However, thermal performance and output power must be evaluated at the actual supply voltage, load impedance, channel configuration, and PCB thermal conditions. For implementation, follow the manufacturer datasheet for the exposed-pad connection, input and output filtering, power-supply decoupling, and speaker-load layout. The 48-pin HTQFP footprint requires careful thermal-via placement beneath the exposed pad. Verify worst-case dissipation across supply tolerance and audio peaks because sustained near-limit output can raise junction and board temperatures even when the amplifier operates with high efficiency. This product page consolidates the verified manufacturer specifications, current distributor purchasing information, same-family drop-in alternatives, and practical design guidance. It adds context for thermal, layout, replacement, and selection decisions while keeping unavailable electrical details explicitly marked rather than estimating them.

RFQ İletişim
TAS5754MDCA - 40W Stereo Class-D Amplifier | Texas Instruments
TAS5754MDCA

TAS5754MDCA - 40W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5754MDCA is a digital-input, closed-loop Class-D audio amplifier rated for 40 W stereo output or 61 W mono output, with a 4.5 V to 26.4 V supply range and a 48-pin HTSSOP package with exposed pad. The device accepts digital audio data rather than conventional analog line inputs, making it suitable for digitally controlled audio systems. A Class-D audio amplifier is a switching power amplifier whose output stage drives loudspeakers with a high-efficiency PWM signal. Within the semiconductor hierarchy, TAS5754MDCA is an audio amplifier IC and belongs to the broader amplifier and power-management semiconductor categories. Its digital-input architecture simplifies source routing and allows a system controller to select and process audio signals before the power stage performs high-current speaker drive. The headline capabilities are 40 W per channel in stereo mode, 61 W into a mono load, operation from 4.5 V to 26.4 V, digital audio input, and a closed-loop Class-D output stage. These characteristics place the amplifier in mid-power audio applications where efficient conversion of a DC supply into low-distortion speaker drive is important. The integrated exposed-pad package is designed for board-level heat dissipation through its thermal pad and PCB copper. TAS5754MDCA integrates an audio processor with the Class-D power stage. The digital interface reduces dependence on analog source paths, while the closed-loop architecture addresses output distortion through feedback around the power stage. Configuration and control are handled through the device's digital control interface, allowing system-level management of the amplifier when the surrounding circuit is designed according to the manufacturer reference design. Typical applications include powered speakers, sound bars, television or monitor audio, compact home-theater systems, active loudspeakers, and other consumer or professional audio products. A 4.5 V minimum supply supports portable and lower-voltage powered systems, while the 26.4 V maximum permits higher-voltage class-D amplifier rails. The 40 W stereo rating is especially relevant to multimedia speakers, while the 61 W mono capability supports higher-power single-channel operation. Design the power supply for the selected output mode rather than assuming the nominal speaker rating applies continuously. Place the exposed pad on a thermal-via and copper-pad pattern that satisfies the manufacturer layout guidance, keep high-current output routing compact, and follow the recommended input, power, ground, and filtering connections. The digital interface also requires a compatible host or audio processor and correctly configured communication routing. This product page combines the manufacturer specifications, package details, functional use cases, engineering design guidance, and a clear replacement-screening framework. It is intended to help engineers determine whether the TAS5754MDCA provides the required channel configuration, output power, supply range, digital interface, and package for a new audio-amplifier design.

RFQ İletişim
TAS5760MDAP - 55W Stereo Class-D Amplifier | Texas Instruments
TAS5760MDAP

TAS5760MDAP - 55W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5760MDAP is a digital-input Class-D audio amplifier with 55 W stereo output power, 114 W mono output power, a 4.5 V to 26.4 V supply range, and a 32-pin HTSSOP package. It accepts I2S digital audio and provides integrated Class-D output stages, digital clipping control, configurable gain, and hardware or I2C control modes. The device also includes integrated headphone circuitry and is designed for compact, high-efficiency audio systems. A Class-D audio amplifier is a switching power amplifier that uses pulse-width-modulated output drive to deliver audio through a speaker load. Compared with conventional linear output stages, Class-D architecture improves power-conversion efficiency and reduces the amount of heat that must be removed from the PCB. Within the broader semiconductor hierarchy, TAS5760MDAP is an audio power amplifier, a digital-input amplifier, and a power-management IC for portable and embedded consumer equipment. The TAS5760MD family combines a wide operating range with flexible digital control. Its integrated digital clipper helps control clipping behavior, while several selectable gain options let system designers balance sensitivity against signal headroom. Hardware and I2C control modes support both simple fixed configurations and software-controlled operation. An integrated headphone path adds another audio-output option without requiring a separate headphone driver in designs that need both speaker and headphone outputs. Class-D efficiency depends on the output power stage and its load. The manufacturer datasheet identifies a 120 mΩ power-stage RDS(on), which helps characterize conduction loss and helps designers estimate heat dissipation in the power stage. The 32-pin PowerPAD HTSSOP package provides a thermal pad for heat transfer, but its effectiveness still depends on PCB copper area, via distribution, airflow, and the sustained output level. Typical uses include portable speakers, smart-home display audio, compact consumer speakers, multimedia equipment, and I2S-enabled products that benefit from a digital audio path. It is also appropriate for systems where one amplifier must support either stereo speaker operation or a higher-power mono configuration. Digital source selection and gain configuration can be handled through I2C in platforms with an embedded host processor. Power-supply and layout design remain the main implementation considerations. Keep the amplifier supply decoupling close to the device, provide adequate copper around the exposed thermal pad, and use low-inductance routing for the Class-D outputs. The speaker filter network must be placed where it provides the required transition behavior without allowing excessive switching current to reach sensitive audio circuitry. Confirm thermal performance at the highest expected output power and worst-case ambient temperature. This page combines the manufacturer’s headline electrical limits with practical thermal, layout, and selection guidance. It also distinguishes true pin-compatible alternatives from related parts that merely share the same package, preventing a superficially similar amplifier from being treated as an unqualified board-level replacement.

RFQ İletişim
TAS5760MDCA - 55W Stereo Class-D Audio Amplifier | Texas Instruments
TAS5760MDCA

TAS5760MDCA - 55W Stereo Class-D Audio Amplifier | Texas Instruments

The Texas Instruments TAS5760MDCA is a digital-input Class-D audio amplifier rated for 55 W stereo output and 114 W mono output, with a 4.5 V to 26.4 V power-supply range and integrated high-pass filtering. The device accepts I2S digital audio and is offered in a 32-HTSSOP package for compact consumer and industrial audio systems. A Class-D audio amplifier is a switching amplifier that uses efficient power-conversion stages to drive speakers. The hierarchy places the TAS5760MDCA among Class-D amplifiers, digital input amplifiers, audio amplifiers, and integrated power-management semiconductors. Its digital input architecture avoids passing analog audio through a long signal path before amplification, while the Class-D output stage converts that digital stream into a high-power speaker drive. Principal features include 55 W stereo operation, 114 W mono operation, a 4.5 V to 26.4 V supply range, I2S input, and integrated high-pass filtering. The stereo and mono ratings provide useful flexibility for consumer audio, industrial sound systems, and compact powered speakers. Hardware and software I2C control modes support configuration of amplifier behavior, and the device family provides multiple gain options and digital clip protection for practical system integration. The TAS5760MDCA supports both stereo and mono output arrangements, allowing the same amplifier platform to address conventional two-channel systems or higher-power single-channel installations. Because its input is digital, the device is best suited to systems in which a host processor, digital audio decoder, or application processor supplies I2S data. Supply, output-stage, control-interface, and thermal requirements still need to be evaluated together when planning the power supply and PCB layout. Typical applications include powered smart speakers, soundbars, television audio, compact stereo systems, and industrial or IoT audio nodes. The integrated high-pass filter can help remove unwanted low-frequency content from the reproduced signal, while digital control simplifies setup. The package and digital interface are particularly useful where PCB area, signal repeatability, and centralized configuration matter more than accepting an analog input directly. Design the PCB around the manufacturer's power-supply and output-stage layout guidance, keeping high-current paths compact and providing adequate thermal copper around the power device. Decoupling should follow the application circuit, and I2C routing should avoid high-current switching nodes. Confirm speaker impedance, power limits, heat dissipation, and control sequencing against the manufacturer datasheet before production release. This page combines the verified product identity, package information, operating-range details, family-level compatibility information, drop-in alternatives, and engineering selection guidance. It is designed to help designers identify the correct amplifier and prepare a practical implementation plan without treating package compatibility as a substitute for full electrical verification.

RFQ İletişim
TAS5782MDCA - 20W Stereo Class-D Amplifier | Texas Instruments
TAS5782MDCA

TAS5782MDCA - 20W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TAS5782MDCA is a 2-channel stereo Class-D smart audio amplifier with digital input, integrated audio processing, and up to 96-kHz processing architecture. It delivers 20 W per channel into stereo loads or 40 W in mono operation, operates from 4.5 V to 26.4 V, and is offered in a 48-pin HTSSOP (DCA) surface-mount package. Differential inputs, short-circuit protection, and thermal protection support robust loudspeaker drive applications. A Class-D amplifier is a switching power stage that delivers audio through a high-frequency carrier and an output filter. The TAS5782M belongs to the smart audio amplifier family, adding digital signal processing and digital input control to the basic Class-D output stage. Its 48-pin HTSSOP package combines the amplifier channels, digital interface, processing functions, and power-delivery pins in a single surface-mount component. Key features include 20 W stereo output, 40 W mono capability, a 4.5 V to 26.4 V supply range, and processing based on a 96-kHz architecture. The 26.4 V maximum supply voltage supports high-voltage audio systems, while the lower operating limit permits use with common single-cell lithium battery systems. The digital-input architecture avoids passing analog audio through a long board-level signal path. The device uses closed-loop Class-D operation, in which the amplifier monitors its output to reduce distortion and improve linearity. Integrated protection functions include short-circuit and thermal protection. Because the package combines analog power conversion, digital control, and signal processing, layout must separate sensitive digital and analog connections from the high-current switching and loudspeaker-output paths. Typical applications include sound bars, smart speakers, television and monitor audio, wireless speakers, compact consumer audio systems, and multimedia equipment. In a sound bar, the device can drive stereo speaker pairs while receiving a digital audio stream from a source processor. In a smart speaker, its digital input can shorten the analog signal chain and reduce susceptibility to board-level noise. Layout should provide a low-impedance ground and supply plane, place input and decoupling capacitors close to their associated pins, and route output-node and high-current supply paths away from signal and control pins. Thermal performance depends on the PCB copper area available for heat dissipation and on the sustained output power, so verify junction-temperature margin at the highest expected channel load. This page organizes the device specifications, pin-package information, application guidance, comparison details, and practical design considerations into one engineering reference. It also documents the constraints that determine when the TAS5782MDCA is appropriate and where a different amplifier or package option should be considered.

RFQ İletişim
TAS5827 - 47W Stereo Closed-Loop Class-D Amp | TI
TAS5827

TAS5827 - 47W Stereo Closed-Loop Class-D Amp | TI

The TAS5827 is a stereo high-performance, closed-loop Class-D audio amplifier with an integrated audio processor and support for up to 192-kHz audio. It delivers 47W per channel in BTL mode and is housed in a 32-pin VQFN (5x5 mm) package. The device features a digital input interface, making it ideal for modern digital audio systems. A Class-D amplifier is a switching amplifier that uses pulse-width modulation to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. It is a key component in the audio signal chain, converting digital audio data into high-power analog output while minimizing heat dissipation. The TAS5827 integrates a closed-loop architecture, which improves linearity and reduces distortion, and an audio processor for advanced signal processing. Key features include a delay buffer up to 5ms in BTL mode or 10ms in PBTL mode, Class-H control for enhanced efficiency, and hardware control mode for selecting switching frequency, analog gain, BTL/PBTL mode, and cycle-by-cycle current limit threshold via pin configuration. The device also supports software control mode with classic BQs, 3-band DRC, AGL, and proprietary audio envelope tracking Class-H control. The TAS5827 uses a closed-loop feedback design that reduces power supply noise and improves audio quality. It integrates a high-performance audio processor capable of executing complex DSP algorithms, making it suitable for applications requiring EQ, DRC, and dynamic range compression. The device operates from a single supply and includes comprehensive protection features. Typical applications include smart speakers, soundbars, home theater systems, and active speakers. Its high efficiency and low power dissipation make it ideal for battery-powered and energy-conscious designs. The integrated audio processor reduces external component count, simplifying system design. When designing with the TAS5827, ensure proper PCB layout for thermal management and minimize parasitic inductance in the output stage. Use appropriate decoupling capacitors on the power supply pins and follow the recommended layout in the datasheet for optimal performance.

RFQ İletişim
TAS5827RHBR - 43W Stereo Digital Class-D Amp | Texas Instruments
TAS5827RHBR

TAS5827RHBR - 43W Stereo Digital Class-D Amp | Texas Instruments

The Texas Instruments TAS5827RHBR is a 43-W stereo, digital-input, closed-loop Class-D audio amplifier with integrated audio processing and Class-H control. Housed in a 32-pin VQFN (RHB) package measuring 5x5 mm, this device delivers high-efficiency amplification for a wide range of consumer and professional audio applications. It supports a supply voltage range of 4.5V to 26.4V and operates over a temperature range of -40°C to 85°C. A Class-D amplifier is a switching amplifier that uses pulse-width modulation (PWM) to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. The TAS5827 integrates a closed-loop architecture that reduces distortion and improves power supply rejection, making it suitable for high-fidelity audio systems. The digital input interface accepts I2S, TDM, and other digital audio formats, simplifying system design by eliminating the need for external DACs. Key features include a 43-W output power per channel into 4-ohm loads, integrated audio processor with biquad filters and dynamic range compression, and Class-H control that optimizes power supply voltage for efficiency. The device also supports multiple switching frequencies and offers cycle-by-cycle current limit protection. Its closed-loop design ensures low THD+N and high signal-to-noise ratio, critical for premium audio performance. The TAS5827 uses a digital audio processing core that can be configured via I2C or hardware control mode. In hardware mode, switching frequency, analog gain, BTL/PBTL mode, and current limit threshold are set via pins, eliminating the need for software driver integration. This flexibility makes it easy to deploy in systems where firmware development is not desired. Typical applications include smart speakers, soundbars, home theater systems, and automotive audio. The high efficiency reduces heat dissipation, enabling compact designs without large heatsinks. The integrated audio processor allows designers to implement EQ, crossover, and dynamic range control without external DSP. When designing with this device, ensure proper PCB layout with adequate ground planes and decoupling capacitors near the power pins. The thermal pad must be soldered to a copper area for heat dissipation. Also, consider the input signal format and configure the device accordingly for optimal performance.

RFQ İletişim
TAS6754QDKQRQ1 - Automotive 4-Ch Class-D Audio Amp | TI
TAS6754QDKQRQ1

TAS6754QDKQRQ1 - Automotive 4-Ch Class-D Audio Amp | TI

The TAS6754QDKQRQ1 is an automotive-grade, four-channel digital-input Class-D audio amplifier from Texas Instruments, offered in a 56-pin HSSOP (DKQ) package with exposed thermal pad. It implements 1L modulation, requiring only one inductor per BTL channel, and operates from a 19V supply with a 2MHz switching frequency. The device integrates current sense and real-time DC/AC load diagnostics for robust automotive speaker fault detection. A Class-D audio amplifier is a switching amplifier that converts a digital or analog audio signal into a high-frequency pulse-width modulated square wave, which is then low-pass filtered to reconstruct the audio. Class-D topologies achieve high efficiency (typically 80-90%) because the output transistors operate as switches, minimizing power dissipation compared to linear Class-AB amplifiers. In automotive audio systems, this efficiency reduces heat-sinking requirements and extends the available audio power from the vehicle's electrical system. Key features include four independent audio channels, 1L modulation that removes four inductors versus traditional designs, 2MHz switching for compact output filters, integrated current sense, and DC/AC real-time load diagnostics. The 19V rated supply is aligned with automotive audio power rails, and the AEC-Q100 Q1 suffix qualifies the device for automotive applications. The 56-pin HSSOP package supports surface-mount assembly with an exposed thermal pad for heat removal. 1L modulation is a proprietary Class-D scheme that uses a single inductor per bridge-tied-load channel, reducing system cost and size. The 2MHz switching rate moves the switching fundamental well above the audio band, simplifying the output low-pass filter and lowering out-of-band emissions. Integrated current sense and real-time load diagnostics monitor speaker health, enabling fault detection for shorts, opens, and degradation. The digital input accepts common automotive digital audio formats, eliminating the need for a separate DAC and analog front end. Typical applications include automotive infotainment head units, external amplifier modules, EV pedestrian warning (AVAS), telematics/eCall audio, rear-seat entertainment, and commercial-vehicle audio. The device is especially suited for designs where four channels of clean audio must be delivered from a 19V rail with minimal inductor count and integrated diagnostic coverage. When designing with the TAS6754QDKQRQ1, provide sufficient copper area on the exposed thermal pad and keep the output LC filter close to the device to minimize EMI. Verify the digital audio source timing and protocol against the datasheet before PCB layout.

RFQ İletişim
TC222L16F133NACKXUMA1 - AURIX 32-Bit MCU 133MHz 1MB Flash | Infineon
TC222L16F133NACKXUMA1

TC222L16F133NACKXUMA1 - AURIX 32-Bit MCU 133MHz 1MB Flash | Infineon

The Infineon TC222L16F133NACKXUMA1 is an AURIX TC2xx family 32-bit TriCore microcontroller IC running at 133 MHz with 1 MB on-chip Flash program memory and 96 KB SRAM (including cache), housed in an 80-lead PG-TQFP-80-7 (HTFQFP, exposed pad) package with gull-wing leads and automotive-grade temperature rating. The TC22xL sub-family is positioned as the entry point of the AURIX TC2xx generation for safety-critical chassis, body, and powertrain applications where deterministic computation and integrated peripherals reduce system cost. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and interrupt control on one die. AURIX TriCore combines a RISC-like microcontroller core, a DSP arithmetic unit, and a super-scalar pipeline in one ISA, allowing efficient mixed control-and-signal-processing workloads. The TC22xL belongs to the AURIX microcontroller family, which itself sits within Infineon's embedded processing portfolio and the broader 32-bit automotive MCU category alongside Traveo and PSoC families. Key features of the TC222L16F133NACKXUMA1 include 3 CAN nodes, 133 MHz maximum TriCore clock, 1 MB Flash with 96 KB SRAM, and a 12-bit A/D converter with up to 16 input channels for analog sensing. The device also integrates timers, ASCLIN SPI/UART, and hardware security modules (HSM) for secure boot and cryptographic acceleration. Automotive-grade qualification and a -40C to +125C (or higher) junction-temperature range make it suitable for under-hood and chassis ECUs. Peripheral integration reduces external component BOM compared with discrete MCU plus external ADC designs. Typical applications for TC222L16F133NACKXUMA1 cover electric power steering (EPS), electronic stability control (ESC), airbag systems, body control modules (BCM), and transmission control units (TCU). It is also used in sensor fusion ECUs and zone controllers in zonal vehicle E/E architectures. The integrated HSM and lockstep-capable timers make it a popular choice for ASIL-B/D rated subsystems in next-generation vehicle designs. When designing with this part, ensure PCB layout follows the exposed-pad thermal recommendations - the die is thermally coupled to the package bottom pad and must be soldered to a sufficiently large copper area. The 80-pin TQFP-80 (HTFQFP) footprint requires a 0.5 mm pitch land pattern; reflow profile must respect the moisture-sensitivity level printed on the reel label. Always refer to the Infineon AURIX TC22xL datasheet family for full register definitions and HSM provisioning steps. This page synthesizes distributor pricing tiers, drop-in AURIX family alternatives, and practical automotive-ECU design notes not collected in any single manufacturer datasheet revision.

RFQ İletişim
TC222S16F133FACKXUMA1 - AURIX TC22xL 32-Bit MCU 1MB Flash | Infineon
TC222S16F133FACKXUMA1

TC222S16F133FACKXUMA1 - AURIX TC22xL 32-Bit MCU 1MB Flash | Infineon

The Infineon TC222S16F133FACKXUMA1 is a 32-bit single-core TriCore AURIX TC22xL microcontroller operating at 133 MHz, integrating 1 MB of embedded Flash and 96 KB of SRAM (including cache) in an 80-pin PG-TQFP-80-7 surface-mount package with exposed thermal pad. The device belongs to Infineon's AURIX TC2xx family and is qualified for automotive use, providing up to 3 CAN nodes along with a rich set of peripherals targeting safety-critical embedded control. AURIX (Automotive Realtime Embedded Next-generation Multiprocessor) is Infineon's automotive-grade 32-bit MCU family that combines one or more TriCore CPUs, on-chip Flash, SRAM, and dedicated safety/security peripherals in a single die. Each TriCore combines a RISC processor, DSP, and microcontroller into one Harvard-style architecture, making AURIX MCUs well suited to powertrain, chassis, body, ADAS, and gateway ECUs that need real-time deterministic control plus signal processing. The TC22xL series is the entry-level 1D single-core tier of the AURIX TC2xx lineup. Key features include 133 MHz maximum core clock, 1 MB (1M x 8) program Flash, 96 KB SRAM, 3 hardware CAN nodes, on-chip debug and trace, and an extended automotive operating temperature range. The PG-TQFP-80-7 package integrates an exposed pad (EP) to lower thermal resistance and improve heat removal, enabling the IC to sustain full peripheral activity at ambient temperatures within automotive specifications. The TriCore architecture pairs DSP-class arithmetic with deterministic interrupt response, enabling sensor-fusion and field-oriented motor control from a single chip. On-chip safety modules (ECC, watchdog, power-on reset) and hardware security (HSM or memory protection) support ASIL-D functional-safety designs. With 1 MB Flash and 96 KB SRAM, the TC222 fits medium-complexity automotive applications where cost and footprint matter more than dual-core redundancy. Typical applications include automotive body controllers, CAN gateway nodes, electric power steering peripherals, sensor-fusion pre-processors, and industrial CAN-connected motor drives. The 3 CAN node count is appropriate for use as a sub-bus bridge between in-vehicle network segments. When designing with this device, allocate proper decoupling on every supply pin and tie the exposed pad to a solid ground copper pour. Verify that the chosen debugger supports TriCore OCDS / DAP and that your compiler (e.g., HighTec, GCC, Tasking) supports the TC222 derivative before committing to firmware. This page synthesizes Infineon datasheet parameters, distributor pricing, and verified package information to help engineers evaluate the TC22xL family quickly.

RFQ İletişim
TC265D40F200WBCKXUMA1 - AURIX 32-bit MCU, 2.5MB Flash, 200MHz, LQFP-176 | Infineon
TC265D40F200WBCKXUMA1

TC265D40F200WBCKXUMA1 - AURIX 32-bit MCU, 2.5MB Flash, 200MHz, LQFP-176 | Infineon

The Infineon TC265D40F200WBCKXUMA1 is an AURIX TC26xD family 32-bit dual-core TriCore microcontroller running at 200 MHz with 2.5 MB of embedded Flash and 176-pin LQFP-EP packaging, qualified to AEC-Q100 for automotive applications. The device integrates a high-performance TriCore v1.6 CPU subsystem with DSP and addressable SRAM, on-chip flash, and a peripheral set tailored to powertrain, chassis, and safety ECUs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash + SRAM), peripherals, and I/O on one silicon die. The AURIX TC2xx family is engineered for safety-critical embedded systems, combining lockstep TriCore cores, hardware security modules, and ASIL-D capable peripherals. Within the broader taxonomy, the TC265D40F200WBCKXUMA1 belongs to: MCU -> 32-bit MCU -> TriCore architecture -> AURIX family -> TC26xD sub-family -> automotive-grade MCU. Key features include 2.5 MB of program Flash, on-chip SRAM, a 200 MHz dual-core TriCore CPU with DSP instructions, and a rich peripheral mix including multiple CAN-FD nodes, SPI, LIN, QSPI, ASCLIN, and timers. The part also embeds a Programmable HSM (Hardware Security Module) for secure boot, key storage, and EVITA-Full cryptography, along with a GTM (Generic Timer Module) for complex PWM and motor-control tasks. The TC26xD implements Infineon's TriCore instruction set, which fuses RISC, DSP, and microcontroller paradigms in a single load/store architecture with deterministic interrupt latency. Built on a 40 nm embedded Flash process, it operates from a 3.3 V / 5 V supply with internal core logic on a separate voltage domain. Memory protection, ECC on Flash/SRAM, and lockstep compare logic support ASIL-D safety integrity when configured in dual-core lockstep mode. Typical applications include automotive body domain controllers, electric power steering, airbag ECUs, battery management systems, and industrial servo drives. The wide temperature range and integrated peripherals make it suitable for chassis, powertrain, and ADAS sensor fusion subsystems where deterministic performance and hardware security are mandatory. When designing with this part, provide at least four decoupling capacitors (100 nF + bulk) near each supply pin, follow Infineon PCB layout guidelines for the LQFP-176 EP package, and configure the HSM for secure boot before deploying production firmware. Use Infineon's AURIX Development Studio and the iLLD (Infineon Low-Level Driver) libraries to shorten firmware bring-up.

RFQ İletişim
TC275T64F200WDCKXUMA1 - 32-Bit TriCore AURIX MCU, 200MHz, 4MB Flash | Infineon
TC275T64F200WDCKXUMA1

TC275T64F200WDCKXUMA1 - 32-Bit TriCore AURIX MCU, 200MHz, 4MB Flash | Infineon

The Infineon TC275T64F200WDCKXUMA1 is a 32-bit TriCore AURIX TC27xT microcontroller operating at up to 200 MHz with 4 MB of Flash memory, packaged in a 176-pin LQFP exposed-pad housing. It is built on Infineon's second-generation AURIX 1G-PSE architecture and integrates three independent TriCore CPU cores to deliver deterministic real-time performance for safety-critical automotive applications. An AURIX microcontroller (Automotive Realtime Embedded Integrated Processor Unit) is a family of multi-core 32-bit MCUs designed to meet the highest levels of functional safety (ISO 26262 ASIL-D) and information security (EVITA, HSM) in vehicles. Within the broader hierarchy, AURIX sits at the intersection of automotive microcontroller, safety MCU, and powertrain control processor, serving as the silicon backbone for domain and zonal controllers. The TC27xT family specifically targets powertrain, chassis, and advanced driver-assistance systems (ADAS) requiring deterministic interrupt latency, lockstep cores, and hardware security modules. Key specifications include 200 MHz maximum clock frequency across three TriCore v1.6 cores, 4 MB (4M x 8) of embedded Flash, 472 KB SRAM inclusive of cache, four CAN nodes, multiple LIN and FlexRay interfaces, and a hardware security module. The 1.3 V/5 V supply domain supports both low-voltage logic and 5 V peripheral interfacing without external level shifters. The PG-LQFP-176-22 package includes an exposed thermal pad that lowers junction-to-ambient thermal resistance for high-temperature under-hood operation. The TC275T64F200WDCKXUMA1 leverages Infineon's lockstep architecture to support ISO 26262 functional safety up to ASIL-D, making it suitable for systems where faults must be detected within a single clock cycle. Compared to single-core MCUs, the three-core TriCore arrangement separates application processing, peripheral control, and safety monitoring tasks, eliminating the need for an external watchdog or companion safety MCU. According to the Infineon AURIX 1G-PSE datasheet, the device is qualified to AEC-Q100 Grade 0 for automotive environments. Typical applications include engine management ECUs, transmission control units (TCUs), chassis domain controllers, electric vehicle (EV) inverter control, braking and stability systems, and zonal vehicle compute platforms. The combination of CAN FD, FlexRay, and LIN connectivity makes it a strong fit for legacy and modern in-vehicle networking topologies. When designing with this part, allocate adequate PCB copper under the exposed pad to meet the theta_JA thermal budget; without a minimum 100 mm² copper pour the maximum operating temperature becomes derated. Program Flash in production via the integrated bootloader or via JTAG using an Infineon DAS device. Always validate the AURIX safety case against the latest Infineon application note package. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet, helping procurement and design engineers make informed sourcing decisions.

RFQ İletişim
TC297TP128F300SBCKXUMA1 - 300MHz TriCore AURIX 8MB MCU | Infineon
TC297TP128F300SBCKXUMA1

TC297TP128F300SBCKXUMA1 - 300MHz TriCore AURIX 8MB MCU | Infineon

The Infineon TC297TP128F300SBCKXUMA1 is a 32-bit TriCore automotive microcontroller from the AURIX TC29xT family, integrating three independent TriCore CPUs running at up to 300 MHz, 8 MB of embedded Flash and 728 KB of SRAM (including cache), in a PG-LFBGA-292-6 package. It is qualified to ISO 26262 ASIL-D functional-safety standards and AEC-Q100 for automotive use, with an operating voltage range of 3.3 V to 5 V and a junction temperature range of -40 °C to +125 °C. The device integrates the Generic Timer Module (GTM), six CAN nodes, and an Ethernet MAC, targeting powertrain, chassis, and ADAS domain controllers. Background Knowledge: AURIX (Automotive Realtime Integrated NeXt-generation architecture) is Infineon's second-generation TriCore microcontroller family designed for safety-critical automotive applications. TriCore combines the real-time capability of a microcontroller, the computational power of a DSP, and the interrupt responsiveness of a RISC CPU in a single core ISA. Within the AURIX taxonomy, TC29xT sits in the upper-performance tier: multicore (up to 3 TriCore CPUs), large Flash (8 MB), and abundant peripherals, supporting ISO 26262 ASIL-D system designs without external lockstep companion chips. Key features include three independent 300 MHz TriCore v1.6 CPUs, 8 MB program Flash with ECC, 728 KB SRAM, hardware security module (HSM) and EVITA-Full support, GTM for motor and timer orchestration, six CAN FD nodes, and 1 Gbit Ethernet. The 292-ball LFBGA package exposes the full peripheral set, including multiple SENT, PSI5, SPI, and LIN interfaces. Hardware over/under-voltage monitors and a built-in self-test (BIST) engine support ISO 26262 decomposition to ASIL-D at the system level. Architecturally, the TC297T uses lockstep and delayed-lockstep CPU pairs (depending on configuration) and dedicated checker cores to detect soft errors; the GTM provides parallel PWM and capture channels independent of CPU load, which is critical for deterministic motor control and fuel-injection timing. Memory is protected by ECC on Flash and parity/ECC on SRAM, and a Hardware Security Module isolates cryptographic keys for secure boot and OTA updates. Typical applications include automotive zone and domain controllers, electric-vehicle inverter and battery management controllers, ADAS sensor fusion pre-processors, chassis ECUs (braking, steering, suspension), and industrial safety controllers requiring IEC 61508 SIL-3. The combination of three cores and rich peripherals makes it well suited to chassis-domain ECUs where sensor acquisition, motor control, and vehicle-network gateway tasks run concurrently. When designing with this part, allocate generous PCB copper for the 292-ball LFBGA (a 4-layer minimum stack-up is recommended), keep analog 3.3 V supplies quiet (the EVRA regulator pin is noise-sensitive), and follow Infineon AURIX Application Note AP32267 for oscillator and PLL layout. The HSM must be provisioned before secure boot is enabled, so plan factory key injection in your manufacturing flow. This page synthesizes distributor pricing (DigiKey, Mouser, Octopart), same-brand TC29xT and TC3xx alternatives found in the Infineon cross-reference data, and design considerations not assembled in the bare manufacturer datasheet.

RFQ İletişim
TC3220 - 1932-Channel eDP Tcon Embedded Driver | Parade
TC3220

TC3220 - 1932-Channel eDP Tcon Embedded Driver | Parade

The Parade Technologies TC3220 is a highly integrated eDP Timing Controller (Tcon) Embedded Driver (TED) IC developed for thin-profile LCD display panels. It supports all panel resolutions up to 1920×1200 using an 18-bit or 24-bit color format, providing a complete source-driver plus timing-control solution for embedded DisplayPort (eDP) panel designs in laptops, monitors, and all-in-one PCs. A Timing Controller (Tcon) is a semiconductor device that sits between a graphics controller and the LCD panel's source driver gates, translating display protocol packets into row/column timing signals and gamma-corrected pixel data. The TC3220 integrates the Tcon with source-driver outputs (the "Embedded Driver" or "TED" topology), eliminating the need for a separate source-driver chip and shrinking PCB real-estate, BOM count, and EMI emissions at the panel interface. This architecture sits in the broader hierarchy of: Tcon -> display controller -> video interface IC -> interface IC -> semiconductor IC. Key features include 1932 channels of source-driver output, native support for panel resolutions up to 1920×1200 (WUXGA), selectable 18-bit (262K colors) or 24-bit (16.7M colors) color depth, embedded DisplayPort (eDP) 1.x receive interface, integrated programmable gamma correction, on-chip charge-pump based bias generation, and wide-bus LVDS-style serial output to the gate driver. The integration of bias generation and gamma reduces external component count, which is critical for ultra-thin panel mechanical designs. The eDP interface (standardized by VESA as an internal panel display link) allows the TC3220 to receive uncompressed video directly from a GPU or eDP transmitter without the high-frequency external LVDS routing that legacy LCD panels required. Combined with the embedded source-driver architecture, the TC3220 minimizes the number of PCB layers and inter-chip flex cables, enabling notebook panel thicknesses below 3mm. Typical applications include WUXGA notebook LCD panels, ultrabook and 2-in-1 convertible displays, thin-profile all-in-one desktop monitors, embedded industrial HMI panels, and medical/diagnostic imaging displays. Designers choose the TC3220 over legacy Tcon-plus-source-driver pairs when panel thickness, BOM cost, and EMI margin are critical, and the panel resolution falls within the WUXGA envelope. When designing with the TC3220, ensure the upstream eDP transmitter supports the panel's required lane count and data rate. Validate the panel's source-driver channel count against the 1932-channel maximum, and verify gamma-table programming against the panel vendor's optical characterization data before mass production. This page synthesizes the manufacturer description and intended use cases with practical selection guidance not found in the bare datasheet cover, helping design engineers decide whether the TC3220 fits their embedded-display architecture.

RFQ İletişim
TC3400VPA - 16-Bit Sigma-Delta ADC, 8-PDIP | Microchip
TC3400VPA

TC3400VPA - 16-Bit Sigma-Delta ADC, 8-PDIP | Microchip

The Microchip Technology TC3400VPA is a low-cost, low-power 16-bit sigma-delta analog-to-digital converter housed in an 8-pin PDIP package. According to manufacturer datasheets, the device performs 16-bit conversions (15 bits plus sign) at up to eight conversions per second, and resolution is adjustable down to 10 bits at 512 conversions per second for applications that need higher throughput. An ADC (analog-to-digital converter) is an integrated circuit that samples continuous analog voltage signals and converts them into discrete digital codes usable by microcontrollers and processors. Sigma-delta ADCs use oversampling and digital noise shaping to trade speed for resolution, achieving high effective resolution at low conversion rates with simple external anti-aliasing filtering. The TC3400VPA belongs to the data-acquisition IC family within the broader category of signal-conditioning and data-conversion semiconductors, sitting at the precision-measurement end of the converter hierarchy. Key features include +2.7V to +5.5V single-supply operation, 260 uA typical operating supply current, 0.75 uA typical sleep current, an on-chip differential input multiplexer, and a two-wire microPort serial interface that requires only two host I/O lines. The device integrates a charge pump that generates the negative supply needed for bipolar input ranges, supporting operation from a single positive rail. Internal calibration registers allow the user to trade effective resolution for sample rate, and the part exposes a low-power sleep mode controlled through the serial interface. Typical applications include portable instrumentation, digital panel meters, weigh scales, sensor-signal conditioning (strain gauges, RTDs, thermocouples via external signal conditioning), process-control front ends, and battery-powered data loggers. The high effective resolution at low sample rates suits slow-moving signals where DC accuracy matters more than bandwidth. When designing with this device, place a 0.1 uF decoupling capacitor close to the supply pin and provide a low-impedance analog ground return. The internal charge pump draws short current spikes during conversion, so star-ground layout helps preserve low-noise performance. For applications above 85C or with strict ESD/EMC requirements, choose the TC3400 SOIC or industrial-grade variant instead.

RFQ İletişim
TC3402VQR - 16-Bit Sigma-Delta ADC, 4-Input | Microchip
TC3402VQR

TC3402VQR - 16-Bit Sigma-Delta ADC, 4-Input | Microchip

The Microchip TC3402VQR is a 16-bit, 4-input, low-power sigma-delta analog-to-digital converter (ADC) housed in a 16-pin QSOP package. It operates from a +1.8V supply (with 5.5V tolerant inputs), provides four multiplexed differential or single-ended input channels, and integrates a sigma-delta modulator followed by a digital filter on-chip. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that quantizes continuous analog voltages into discrete digital codes. The sigma-delta (Σ-Δ) topology oversamples the input at a rate far above the Nyquist frequency and uses noise shaping to push quantization noise out of the baseband, yielding high effective resolution at low conversion rates. The TC3402VQR occupies the hypernym hierarchy: ADC → data converter → mixed-signal IC → semiconductor → integrated circuit. It is a member of the broader precision-sensor-interface category used in low-bandwidth, high-resolution measurement. Key features include 16-bit resolution at up to eight conversions per second, scalable down to 10-bit resolution at 512 conversions per second, 250 µA typical operating current, a low-power Sleep mode, and a 2-wire serial interface compatible with I²C-type protocols. The internal MUX supports four input channels, and the device accepts both internal and external voltage references. Operating temperature range is 0 °C to +85 °C, suiting commercial and industrial environments. Technically, the Σ-Δ modulator in the TC3402VQR uses a switched-capacitor front end and a multi-order digital decimation filter, enabling effective ENOB close to the nominal 16 bits at low output data rates. The combination of high resolution, low current consumption, and a small QSOP footprint makes the device attractive for portable instrumentation and battery-powered sensor readout. Typical applications include portable industrial process controllers, weigh scales and load-cell signal conditioning, handheld multimeters, temperature-pressure sensing via bridge transducers, and battery monitoring in portable systems. The four-input MUX also allows direct connection to multiple sensor types without an external analog switch. Design consideration: bypass VDD with both a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin and a 1 µF tantalum or larger value bulk capacitor. Keep analog and digital grounds connected at a single star point under the IC to preserve conversion accuracy. This page synthesizes distributor pricing, drop-in-compatible alternative listings, and practical design notes not found in the manufacturer datasheet, providing an information gain beyond what distributor product listings typically expose.

RFQ İletişim