Ürünler (46.000+)

ISL8483EIB - 5V RS-485/RS-422 Transceiver | Renesas Electronics
ISL8483EIB

ISL8483EIB - 5V RS-485/RS-422 Transceiver | Renesas Electronics

Renesas Electronics ISL8483EIB is a single RS-485/RS-422 transceiver operating from a 5 V supply, with integrated protection for driver outputs and receiver inputs against electrostatic-discharge strikes up to ±15 kV. The device is packaged in an 8-pin SOIC and supports balanced differential communications over industrial, instrumentation, automation, and point-to-point data links. A transceiver combines a differential line driver and receiver in one integrated circuit, allowing a printed circuit board to transmit and receive on the same balanced bus wiring. Within the interface-IC hierarchy, the ISL8483EIB belongs to the RS-485/RS-422 interface family, combines data communication with ESD protection, and is used where noise immunity, ground-offset tolerance, and common-mode rejection improve reliability over single-ended signaling. The manufacturer identifies the ISL8483E family as ESD-protected, low-power BiCMOS transceivers for 5 V operation. The ISL8483EIB provides one driver and one receiver in an 8-SOIC package. Its ±15 kV ESD protection is a principal feature for exposed communications equipment, while short-circuit current limiting and on-chip thermal shutdown help the driver withstand bus contention. These protections address field-level faults encountered in industrial wiring. BiCMOS construction combines bipolar and CMOS characteristics, supporting low-power operation and high-speed balanced signaling. The RS-422 mode supports point-to-point and multidrop communication, while RS-485 permits multiple drivers on a shared bus when the system designer controls inactive states, termination, and biasing correctly. The exact propagation-delay, slew-rate, data-rate, output-current, and temperature limits should be selected from the manufacturer datasheet for the intended system conditions. Typical uses include industrial sensor gateways, motor-control diagnostics, factory equipment interfaces, building automation, instrumentation links, and embedded serial buses. In each case, the transceiver converts logic-level serial information into balanced differential signals and returns differential bus data to receiver logic, reducing susceptibility to electromagnetic noise over longer interconnects. Designers should use a common ground reference between the transceiver and system electronics, place termination at the physical ends of the bus, and provide a bias network only when the installed network requires it. Protection components and chassis-ground design must be evaluated against the actual cable environment. Input and output filtering should be tested for signal-integrity margin before production release. This product page combines manufacturer specifications, source-linked availability information, interface use cases, and practical PCB-design considerations to support component selection and replacement planning. The ISL8483EIB is especially relevant when an existing 8-SOIC RS-485 or RS-422 design requires 5 V operation and ±15 kV ESD-protected driver or receiver nodes.

RFQ İletişim
ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas
ISL8483EIP

ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8483EIP is a 5 V, single-channel RS-485/RS-422 interface transceiver with one transmitter and one receiver, packaged in an 8-pin PDIP. It provides ±15 kV ESD protection at the driver outputs and receiver inputs, combines BiCMOS circuitry with short-circuit current limiting, and includes on-chip thermal shutdown for dependable operation during bus contention. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and longer distances. RS-422 emphasizes point-to-point, balanced signaling, while RS-485 supports multidrop buses and driver-enable control. This device bridges the single-ended digital domain and the differential bus, placing it within the interface IC, communication IC, and semiconductor hierarchy. Key features include one half-duplex transmitter, one receiver, 5 V operation, and device-level ESD protection of ±15 kV. Driver short-circuit current limits help protect the outputs when a bus node is driven against another active node. Thermal shutdown adds a secondary protection mechanism when sustained contention or abnormal loading raises internal dissipation. The ISL8483 family combines BiCMOS implementation with low-power operation and two signal-rate options identified by the ISL8483 and ISL8485 family members. The E version adds enhanced ESD protection, while the receiver and driver control arrangement supports implementation of half-duplex nodes. Exact data rate, propagation delay, slew rate, and common-mode limits should be selected from the family datasheet for the intended bus topology. Typical uses include industrial RS-485 field buses, building automation equipment, factory data links, RS-422 point-to-point links, and industrial control modules. The device is particularly suitable when a design needs a single transceiver, balanced differential signaling, 5 V supply operation, and reinforced ESD protection near a connector or externally accessible cable. PCB implementation should keep the transceiver close to the connector, route the differential pair as a tightly matched pair, and provide a low-impedance return path. Decoupling capacitors should connect to the ground plane with short traces, and unused or unused-condition control inputs must be driven to defined logic levels to prevent an indeterminate bus state.

RFQ İletişim
ISL8483IB - 250kbps Half-Duplex RS-485/RS-422 IC | Renesas
ISL8483IB

ISL8483IB - 250kbps Half-Duplex RS-485/RS-422 IC | Renesas

Renesas Electronics ISL8483IB is a 5 V, 250 kbps half-duplex RS-485/RS-422 transceiver with separate receiver and transmitter enables, low-power shutdown, and optional slew-rate-limited operation in an 8-pin SOIC package. The part is designed for industrial-grade, point-to-point and multidrop serial-interface systems requiring bidirectional data transfer over a balanced cable. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential bus voltages. RS-422 provides a driver-dominant, point-to-point signaling method, while RS-485 permits multiple drivers on a shared bus when only one node transmits at a time. The ISL8483IB combines one transmitter and one receiver in one package, supporting half-duplex communication over a common pair of differential conductors. Key features include a 250 kbps data rate, a 5 V supply, separate Rx and Tx enables, and a low-power shutdown function. The verified distributor description also identifies a slew-rate-limited configuration option. Slew-rate control reduces the edge speed of transmitted signals, limiting high-frequency harmonics and electromagnetic interference at the expense of maximum signaling rate compared with an unrestricted high-speed driver. The ISL8483IB uses separate active-high receiver-enable and driver-enable controls, allowing the host to place the unused side of the transceiver into a disabled state. Its bidirectional half-duplex arrangement is useful where two endpoints exchange requests and responses over a shared pair of wires. The device also supports transmitter shutdown for systems that need to reduce supply consumption when the bus is inactive. Typical applications include industrial serial interfaces, remote monitoring equipment, data acquisition modules, building-control systems, factory automation links, and RS-485-to-TTL conversion products. The 8-pin SOIC package supports conventional surface-mount assembly. The industrial temperature grade identified by the verified distributor listing makes the device suitable for equipment operating across an extended commercial temperature range, subject to the manufacturer's specified limits. Designers should verify the complete datasheet pinout, absolute maximum ratings, recommended external network, driver-load capability, and shutdown behavior before releasing a PCB. Cabling, termination, grounding, and transceiver-enable sequencing are as important as the nominal 250 kbps rating because unbalanced or incorrectly terminated buses can cause reflections, common-mode voltage errors, and unreliable communication. This page combines verified distributor information, structured drop-in-family alternatives, application guidance, and design notes in a format designed to accelerate component selection, replacement planning, and hardware implementation.

RFQ İletişim
ISL8483IB-T - Half-Duplex RS-422/RS-485 Transceiver | Renesas
ISL8483IB-T

ISL8483IB-T - Half-Duplex RS-422/RS-485 Transceiver | Renesas

Renesas Electronics ISL8483IB-T is a single-channel, half-duplex interface transceiver supporting RS-422 and RS-485 communications in an 8-pin SOIC package. The device combines one driver and one receiver in a compact package, making it suitable for bidirectional industrial data links where both transmitting and receiving functions are required on the same bus. A half-duplex RS-422/RS-485 transceiver is a physical-layer interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into logic levels. Within the interface hierarchy, the ISL8483IB-T belongs to the transceiver class of interface ICs, combining an RS-422/RS-485 driver, an RS-422/RS-485 receiver, and bus-facing control functions in one package. Differential signaling supports reliable communication over longer cable runs while reducing sensitivity to common-mode noise. The verified manufacturer-related listing identifies the ISL8483IB-T as a one-driver, one-receiver, half-duplex RS-422/RS-485 transceiver in an 8-SOIC package. Its principal engineering benefits are component consolidation, a compact surface-mount footprint, and support for both RS-422 and RS-485 point-to-point networks. The single driver and receiver arrangement also helps designers manage bus direction explicitly in half-duplex systems. The part is appropriate for industrial controllers, factory automation equipment, remote sensor interfaces, and embedded communications modules. In these systems, the transceiver connects a host UART or programmable controller to a differential bus while converting logic signals to and from the physical network. The 8-pin SOIC package supports conventional PCB assembly methods and is smaller than many legacy through-hole transceiver packages. Designers should verify the final electrical limits, receiver fail-safe behavior, driver enable polarity, and bus termination requirements against the manufacturer datasheet before releasing production hardware. In half-duplex implementations, correct driver-enable timing is essential to prevent contention, while proper biasing and termination help maintain signal integrity on the RS-422 or RS-485 network. This page combines the verified Renesas product identity, exact package classification, interface capability, sourcing information, available drop-in references, and practical implementation guidance. It is intended to help engineers identify the correct device, plan PCB connections, and compare compatible RS-422/RS-485 interface options before detailed circuit validation.

RFQ İletişim
ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas
ISL8483IBZ

ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas

The Renesas Electronics ISL8483IBZ is a 5 V, low-power RS-422/RS-485 interface transceiver with one transmitter and one receiver in an 8-pin SOIC package. It operates from a 4.5 V to 5.5 V supply across a -40 °C to +85 °C temperature range. Its slew-rate-limited driver is designed to reduce electromagnetic interference and reflections associated with poorly terminated transmission lines or unterminated stubs. An RS-422/RS-485 transceiver is an interface IC that converts logic-level signals into differential line signals and receives differential line signals back into logic-compatible outputs. The wider category hierarchy is transceiver > line driver and receiver > differential interface IC > interface IC > semiconductor. These devices support communication over cables and printed-circuit-board traces where noise immunity, galvanic signal polarity, and multi-drop behavior are important engineering considerations. The ISL8483IBZ combines one differential driver and one differential receiver in a single 8-SOIC package. Its operating supply range of 4.5 V to 5.5 V suits conventional 5 V equipment, while the industrial temperature range supports factory automation, instrumentation, and embedded control systems. Slew-rate limiting is particularly useful in multidrop and multipoint networks because it reduces edge energy and helps limit reflected signals on imperfectly terminated cables. The device family documentation distinguishes high-speed and slew-rate-limited RS-485/RS-422 implementations. ISL8483-family devices use slew-rate-limited drivers to reduce EMI and minimize reflections from improperly terminated transmission lines or unterminated stubs. Exact data rate, receiver thresholds, driver output impedance, and propagation-delay limits must be taken from the manufacturer datasheet when they are required for link-budget or timing calculations. Typical applications include industrial sensor buses, factory-floor equipment interfaces, building-control networks, remote instrumentation, and embedded serial links. The differential interface can improve noise tolerance over longer interconnects than a single-ended implementation, provided the network uses the correct topology, termination, biasing, and common-mode limits. PCB design should preserve a continuous ground reference beneath the transceiver, keep differential traces closely coupled, and place termination and any fail-safe bias network at the physical cable ends. Avoid adding large test pads or unrelated high-current paths between the differential pair because those structures can unbalance the pair and reduce common-mode noise rejection. This product guide consolidates the verified package, voltage, temperature, interface, and sourcing information into an engineer-oriented reference. It also distinguishes the exact ISL8483IBZ from the ESD-protected ISL8483E-family option and identifies where pinout, timing, and application-specific conditions must be confirmed in the manufacturer documentation.

RFQ İletişim
ISL8483IP - 5V RS-485/RS-422 Transceiver | Renesas
ISL8483IP

ISL8483IP - 5V RS-485/RS-422 Transceiver | Renesas

Renesas ISL8483IP is a single half-duplex RS-485/RS-422 transceiver operating from a 5 V supply, with selectable low-power high-speed or slew-rate-limited operation. The device combines one transmitter and one receiver in an 8-pin PDIP package and includes separate receiver and transmitter enables plus a low-power shutdown function. Verified distributor data identifies the ISL8483IP as a 250 kbps half-duplex RS-485/RS-422 transceiver with Rx/Tx enables and low-power SHDN. The package is specified as 8-DIP, or 8-PDIP, with a 0.300 inch, 7.62 mm body width. An RS-485/RS-422 transceiver is a balanced-interface interface IC used to connect a logic-level controller to a differential communication bus. RS-422 generally describes a point-to-point, balanced digital interface, while RS-485 supports multipoint bus arrangements and commonly uses transceivers that can disable their drivers when idle. The ISL8483IP belongs to the interface IC hierarchy and is intended for industrial-control, instrumentation, and embedded serial links requiring a 5 V supply and differential noise immunity. The verified data identifies a maximum signaling rate of 250 kbps and offers two operating approaches described as high speed or slew-rate limited. These modes are relevant when a design must balance communication rate against the transition rate of the differential driver. Additional control features named in the source material are the receiver enable, transmitter enable, and low-power shutdown input, allowing the host to manage bus direction and conserve power when communication is inactive. The ISL8483IP uses BiCMOS technology in the Intersil RS-485 and RS-422 product family. Although the provided search results describe the family as meeting both RS-485 and RS-422 standards, detailed limits for differential output voltage, receiver threshold, common-mode range, supply-current behavior, and isolation are not included in the supplied excerpts. Those parameters therefore require confirmation in the manufacturer datasheet before final circuit release. Typical applications include industrial sensor and actuator links, factory automation equipment, building-control systems, laboratory instrumentation, and embedded controllers communicating with remote RS-485 peripherals. The 250 kbps rate is appropriate for moderate-speed control and monitoring networks rather than high-bandwidth data transfer. In a multidrop bus, only one transmitter should normally be active at a time, while the receiver can monitor bus state when its driver is disabled. A key design consideration is the distinction between the PDIP and surface-mount ISL8483 package variants. Cross-reference results explicitly identify ISL8483EIBZ-T and ISL8483EIBZ-T7A as SOIC-8 surface-mount parts, so they are not drop-in replacements for an 8-PDIP board footprint. Before routing a replacement PCB, verify supply voltage, data rate, enable polarity, shutdown behavior, pinout, and transceiver-versus-receiver configuration against the manufacturer datasheet. This page consolidates the verified distributor descriptions, package distinctions, sourcing links, and practical replacement constraints into an engineering-focused view. It also identifies where the supplied evidence is incomplete, avoiding unsupported claims about pin assignments, electrical limits, lifecycle state, pricing, and thermal performance. Those fields should be completed from the authoritative manufacturer datasheet and current authorized distribution records.

RFQ İletişim
ISL8483IPZ - 5V RS-485/RS-422 Transceiver | Renesas
ISL8483IPZ

ISL8483IPZ - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8483IPZ is a 5 V, single-transmitter and single-receiver RS-485/RS-422 interface transceiver packaged in an 8-pin PDIP. It combines a balanced differential driver and receiver in one package, supports communication over 0 to 70 °C, and uses slew-rate-limited drive to reduce electromagnetic interference and transmission-line reflections. The device is RoHS compliant and includes ESD-protected communications pins. An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic signals and balanced differential signals. This signal format rejects common-mode noise and supports reliable communication over longer cables or across systems with different ground potentials. Within the broader semiconductor hierarchy, the ISL8483IPZ is a line-driver and line-receiver device, an interface IC, and a communications peripheral used between digital controllers and balanced-wired networks. Key features include operation from a single 5 V supply, one driver and one receiver, support for both RS-485 and RS-422 applications, and slew-rate-limited outputs. Slew-rate limiting is particularly valuable in multidrop and multipoint networks because it lowers the high-frequency content of the driver edge. This helps control EMI and reduces reflections caused by unterminated transmission lines or stubs. The package also provides a straightforward through-hole footprint for legacy and industrial equipment. The transceiver architecture supports point-to-point RS-422 links as well as multidrop RS-485 networks. The receiver provides the balanced input path, while the driver converts outgoing logic levels into differential line signals. Biasing, termination, common-mode range, driver loading, and maximum cable length remain system-level design considerations. Because those operating limits are not stated in the available product information, consult the manufacturer datasheet before finalizing network geometry or cable assumptions. Typical uses include industrial instrumentation, factory automation equipment, building controls, industrial sensor gateways, remote monitoring links, and embedded serial buses. The same transceiver can be used in designs where interoperability between RS-422 and RS-485 equipment matters, provided the system configuration and termination strategy match the selected standard. Its through-hole package also makes it useful for repairs and expansions of boards designed around DIP-style interface devices. When laying out the circuit, keep the balanced traces short, route the driver and receiver differential pair together, and avoid placing unrelated switching nodes between the two conductors. Apply termination only where it belongs in the network topology, normally at the physical ends of the cable. Confirm logic polarity, receiver enable behavior, grounding strategy, and bus loading against the manufacturer application guidance before applying power. This product page combines the exact package and interface classification with application guidance, engineering design notes, and a compatibility-focused comparison. These practical details help engineers evaluate the ISL8483IPZ for industrial communications while separating confirmed device characteristics from parameters that must be confirmed in the manufacturer datasheet.

RFQ İletişim
ISL8484IR - 4.5V Dual SPDT Low-RON Switch | Renesas
ISL8484IR

ISL8484IR - 4.5V Dual SPDT Low-RON Switch | Renesas

The Renesas Electronics ISL8484IR is a low-voltage, bidirectional, dual single-pole/double-throw analog switch with an ultra-low ON-resistance, a +1.65 V to +4.5 V single-supply range, and a 10-pin DFN package with an exposed pad. Its specified ON-resistance is 0.29 ohm at a 4.3 V supply, 0.33 ohm at 3.0 V, and 0.55 ohm at 1.8 V. The device contains two independently controlled SPDT switches, allowing one signal or supply path to be routed between two external nodes at a time. Typical on-resistance matching between channels is 0.06 ohm, while ON-resistance flatness across the signal range is 0.03 ohm. An analog switch is a semiconductor device that connects or disconnects an electrical signal path with controlled resistance. In the product hierarchy, the ISL8484IR is an analog switch and multiplexer within the broader interface IC category. Each SPDT configuration provides a common terminal, one normally closed throw, and one normally open throw, making the device useful for signal routing, polarity selection, test-point isolation, and compact analog multiplexing. The defining feature of the ISL8484IR is its low channel resistance across a low-voltage supply range. The manufacturer datasheet also identifies it as a pin-compatible replacement for the MAX4684 and MAX4685. Its low power consumption, specified below 0.45 microwatt in the cited operating conditions, and fast switching behavior make it appropriate for battery-powered and portable equipment where signal-path resistance and energy use both matter. The two independent SPDT switches provide routing flexibility without requiring two separate packages. Matching and flatness characteristics help reduce channel-dependent attenuation and distortion when a design switches between sources or measures multiple nodes. The bidirectional signal path also permits operation in either current direction, although the permitted voltage and current limits must remain within the manufacturer ratings. Typical uses include low-voltage audio routing, sensor selection, test and measurement interfaces, portable instrumentation, and general-purpose power or signal multiplexing. The low 1.65 V minimum supply supports systems operating from a single lithium-cell rail or other low-voltage source. In precision analog paths, engineers should verify the actual ON-resistance, leakage, charge injection, and switching timing under the intended signal amplitude and frequency. The primary design consideration is preserving the exposed-pad thermal and electrical requirements of the 10-DFN package. Place the exposed pad on a PCB thermal-via and ground-plane structure, keep high-current paths physically short, and confirm the selected switch state during power-up. Because the supplied search data does not include the complete pin table, engineers should download the Renesas datasheet before assigning signals to physical pins. This page consolidates the verified manufacturer description, parametric ON-resistance data, operating-voltage range, package information, and cross-reference evidence. It also distinguishes documented drop-in replacements from package or packaging variants that are not true PCB drop-in choices, helping engineers evaluate replacement risk before redesigning a board.

RFQ İletişim
ISL8484IRZ - 0.4 Ohm Dual SPDT Analog Switch | Renesas
ISL8484IRZ

ISL8484IRZ - 0.4 Ohm Dual SPDT Analog Switch | Renesas

Renesas ISL8484IRZ is a low-voltage dual SPDT analog switch with 0.4 ohm on-resistance, 2:1 multiplexing, and operation from +1.65 V to +4.5 V in a 10-lead TDFN package. The switch is designed for compact, low-voltage systems requiring low signal resistance, fast switching, and single-supply operation. An analog switch is a semiconductor device that routes analog signals between input and output terminals under digital control. The SPDT configuration provides one common terminal and two switched terminals for each circuit, allowing two independent 2:1 selections. In the power-management hierarchy, this dual SPDT switch functions as a low-voltage interface IC for signal routing, test-point multiplexing, and programmable analog paths. Key electrical characteristics include an on-resistance of 0.29 ohm at +4.3 V, 0.33 ohm at +3.0 V, and 0.55 ohm at +1.8 V. On-resistance matching between channels is 0.06 ohm, while flatness across the signal range is 0.03 ohm. At +4.3 V, turn-on time is 40 ns and turn-off time is 20 ns. The device also provides guaranteed break-before-make behavior. The dual independent-switch architecture supports simultaneous routing of two analog signals. Its low-voltage supply range makes it suitable for battery-powered instrumentation, portable measurement systems, low-voltage test equipment, and mixed-signal interfaces. The manufacturer identifies the ISL8484 as a pin-compatible replacement for the MAX4684 and MAX4685, with particularly low on-resistance across its stated supply conditions. Typical circuit roles include selecting between two sensors, connecting a test fixture to a measurement instrument, routing one of two sources into an amplifier, and multiplexing an analog control point. Because the switch operates from a single supply, system designers should confirm that every driven signal remains within the permitted input and output range during switching transitions. For layout, route the common, switched, and control traces with short analog paths and maintain a continuous ground reference beneath the device. Place bypass capacitance near the supply pin and avoid routing high-impedance signals beneath digital control traces. These practices reduce parasitic distortion and coupling during the 40 ns switching transitions. This product page combines the manufacturer specifications with a parameter-by-parameter comparison, verified pin-compatible alternatives, and practical routing guidance. Use the Renesas ISL8484 documentation as the authoritative source for the final pin-description table, footprint dimensions, and production release limits before releasing a PCB layout.

RFQ İletişim
ISL8484IU - Dual SPDT Low-Voltage Analog Switch | Renesas
ISL8484IU

ISL8484IU - Dual SPDT Low-Voltage Analog Switch | Renesas

Renesas Electronics ISL8484IU is a dual single-pole/double-throw analog switch with a single-supply operating range of +1.65 V to +4.5 V and an ultra-low on-resistance. The device contains two independent SPDT switch circuits in a 10-MSOP package and is designed for low-voltage, low-power signal-routing applications. Its stated on-resistance is 500 mOhm, while the available technical data also identifies 290 mOhm at a 4.3 V supply and 550 mOhm at a 1.8 V supply. An analog switch is an integrated interface circuit that routes electrical signals between terminals under digital control. A dual SPDT switch provides two selectable signal paths per switch section, making it useful for selecting one of two sources, routing a measurement signal, or supporting bidirectional communication. The ISL8484 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. The principal feature of the ISL8484IU is its low on-resistance across a low-voltage supply range. Available data lists on-resistance matching between channels as 0.06 Ohm and on-resistance flatness across the signal range as 0.03 Ohm. Power consumption is specified below 0.45 uW, while fast switching action is available when the supply is 4.3 V. These characteristics suit compact equipment operating from a single low-voltage rail. The device uses separate select and common terminals for each SPDT section. The 10-MSOP surface-mount package is offered in a 0.118-inch by 3.00 mm width format. The supplied data identifies the industrial temperature grade and 10 terminals. A publicly verified pin-number-to-pin-name diagram was not present in the supplied results, so the exact pinout is intentionally left unassigned rather than inferred from generic package conventions. Typical uses include low-voltage audio routing, sensor and measurement-signal selection, portable test equipment, communication-signal multiplexing, and compact industrial interfaces. For bidirectional signal paths, the control and common terminals must be operated within the voltage limits specified by the manufacturer datasheet. Care is required when switching powered signals because the exact overvoltage and break-before-make behavior should be confirmed from the current datasheet. A primary design consideration is the relationship between supply voltage and switch resistance. Lower supply operation provides less headroom for the internal switch and corresponds to higher resistance, while operation near 4.5 V provides the lower-resistance behavior listed in the available data. PCB layout should keep routing short and provide a stable return path, especially when the switch handles high-bandwidth or low-amplitude signals. This product page consolidates the verified manufacturer description, distributor inventory information, package details, switch characteristics, cross-reference findings, and practical engineering guidance. It also separates verified facts from unavailable values so designers can identify the target part quickly while recognizing which parameters still require confirmation in the current manufacturer datasheet.

RFQ İletişim
ISL8484IUZ - Dual SPDT Analog Switch, 0.29 Ohm | Renesas
ISL8484IUZ

ISL8484IUZ - Dual SPDT Analog Switch, 0.29 Ohm | Renesas

The Renesas Electronics ISL8484IUZ is a dual single-pole/double-throw (SPDT) analog switch with 0.29 ohm ON-resistance at V+ = 4.3 V, operating from a single +1.65 V to +4.5 V supply, and packaged in a 10-lead MSOP (10-TFSOP). Each switch routes one common node to one of two throws, giving two independent 2:1 muxes in one IC. An analog switch (also called a mux or multiplexer) is an integrated circuit that steers a signal path between multiple sources and destinations under digital control. It belongs to the signal-path hierarchy: analog switch -> multiplexer -> interface IC -> integrated circuit. Unlike a relay or mechanical contactor, it switches in nanoseconds, draws micro-watts of power, and introduces only a small, well-characterized series resistance plus a few picofarads of parasitic capacitance. Key features of the ISL8484IUZ include very low ON-resistance that stays flat across the signal range, excellent channel-to-channel rON matching of 0.06 ohm, low power consumption below 0.45 microwatts, fast switching of 40 ns tON and 20 ns tOFF at V+ = 4.3 V, guaranteed break-before-make behavior, and an HBM ESD rating of greater than 8 kV. The manufacturer also documents the ISL8484 family as a pin-compatible replacement for the MAX4684 and MAX4685. Because ON-resistance is only 0.29 ohm and rON flatness across the signal range is 0.03 ohm, the device behaves almost like a shorted trace when closed. This makes it well suited to routing low-frequency analog signals, sensor outputs, reference voltages, and baseband paths where added resistance would degrade accuracy. The very low switching energy keeps the switch usable in battery-powered and portable equipment. Typical uses include audio and headphone signal routing, portable test equipment, battery-powered sensor interfaces, USB and peripheral routing in low-voltage designs, and general-purpose analog multiplexing in consumer and industrial systems running from 1.8 V to 3.3 V rails. The key design consideration is supply headroom: the switch operates down to +1.65 V, but ON-resistance rises sharply as V+ falls (0.55 ohm at 1.8 V versus 0.29 ohm at 4.3 V). Budget the signal-path error against the highest rail in your system, and treat the control pins as logic inputs referenced to the same V+ supply.

RFQ İletişim
ISL8485CB - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485CB

ISL8485CB - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8485CB is a 5V, low-power, high-speed RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package. It combines one driver and one receiver in a single integrated circuit for balanced industrial communication links, with a verified data rate of up to 5Mbps. The device operates from a single 5V supply and supports both high-speed and slew-rate-limited communication modes. Its 8-SOIC package is suitable for conventional surface-mount PCB assembly, while its half-duplex architecture allows one transceiver to share a bidirectional bus with controlled driver enable and receiver enable functions. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and receives differential signals back into CMOS-compatible logic levels. The ISL8485CB belongs to the transceiver hierarchy of interface ICs, where RS-422 provides a balanced point-to-point or multidrop communication format and RS-485 supports longer, noise-tolerant multipoint buses. The part is intended for systems that require compact, reliable differential signaling rather than a single-ended communications interface. The primary electrical attributes include a 5V supply, a 5Mbps data rate, one integrated driver, and one integrated receiver. The manufacturer family documentation identifies the ISL8485 as a CMOS 5V-powered RS-485/RS-422 transceiver family with low power consumption and both high-speed and slew-rate-limited configurations. The verified distributor description identifies the CB ordering code as an 8-SOIC, while the manufacturer document covers the related ISL8485, ISL8490, and ISL8491 family. Typical uses include industrial control systems, factory automation, instrumentation, building automation, and embedded equipment connected through a balanced bus. In a half-duplex network, the transceiver converts transmitted data into differential bus voltage and receives remote data when the driver is disabled. The 5Mbps capability supports high-rate factory communication, while slew-rate limiting can reduce reflected signaling on longer or less controlled cables. Designers should verify the complete pinout, enable polarity, driver and receiver disable behavior, termination requirements, and electrical limits against the Renesas datasheet before layout. RS-485 buses normally need termination at both physical ends, biasing to provide a defined idle state, and protection appropriate to the installation environment. The 8-SOIC package requires thermal and layout attention at elevated data rates or long-cable installations.

RFQ İletişim
ISL8485CB-T - 5V RS-485/RS-422 Transceiver | Renesas
ISL8485CB-T

ISL8485CB-T - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8485CB-T is a 5 V, low-power RS-485/RS-422 line transceiver packaged in an 8-pin SOIC. It supports data rates up to 5 Mbps, operates from a 4.5 V to 5.5 V supply, and presents one unit load to an RS-485 bus. The device combines one driver and one receiver in a half-duplex transceiver arrangement for balanced industrial communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals between a host controller and a differential communication bus. The driver transmits complementary differential signals, while the receiver detects the voltage difference across the pair. As a single-channel half-duplex transceiver, the ISL8485CB-T supports one communication line while sharing the same package and bus connection structure used by related ISL8485 devices. The family is specified for 10% supply tolerance, providing a 4.5 V to 5.5 V operating range. Its BiCMOS construction supports low power consumption while operating at rates up to 5 Mbps. The ISL8485CB-T also provides ESD-protected, single-driver, single-receiver operation, making it suitable for point-to-point RS-422 links and multidrop RS-485 networks that require compact, surface-mount transceivers. Renesas describes the ISL8485 family as a collection of 5 V-powered RS-485 and RS-422 transceivers. The CBZ-T ordering code is associated with a lead-free and RoHS-compliant version, while the CB-T designation identifies the tape-and-reel ordering configuration used in this listing. The 8-pin SOIC package supports conventional surface-mount assembly and is compatible with compact industrial and embedded control equipment. Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, and embedded systems communicating over long differential cable runs. The 5 Mbps maximum data rate supports moderately high-speed control and data traffic, while the one-unit-load bus loading helps preserve network capacity when multiple transceivers share a bus. PCB design should account for the difference between supply current and bus return current. Place the transceiver close to the connector and transceiver protection network, keep the differential pair routed as a tightly coupled pair, and provide the supply bypass capacitance recommended by the manufacturer. The 8-pin SOIC footprint should be checked against the PCB library before substitution because narrow-body variants can differ in lead width and courtyard dimensions. This product page combines the manufacturer family description, distributor package and ordering information, current sourcing records, interface characteristics, and practical replacement guidance. It also distinguishes the exact ISL8485CB-T ordering code from related ISL8485 variants so engineers can evaluate footprint, supply, ESD, and rate requirements before approving a replacement.

RFQ İletişim
ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
ISL8485CBZ

ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

Renesas Electronics ISL8485CBZ is a 5 V, half-duplex, 1-transceiver/1-receiver RS-485 and RS-422 interface IC capable of operation to 5 Mbps. It is packaged in an 8-pin SOIC and supports a 4.5 V to 5.5 V supply range, providing tolerance for industrial 5 V rails. The device presents one unit load to an RS-485 bus and combines a balanced line driver, differential receiver, and half-duplex control in a compact package. An RS-485/RS-422 transceiver is an interface device that translates logic-level signals into balanced differential signals for reliable communication over longer cables and electrically noisy environments. It belongs to the interface IC hierarchy, connecting digital controllers and processors to field buses or point-to-point differential links. Balanced signaling improves common-mode noise immunity, while bus direction control allows a single transceiver pair to support two-way communication. Key characteristics include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply, and compatibility with both RS-485 and RS-422 communication standards. The half-duplex configuration multiplexes driver and receiver functions onto shared bus pins. Driver short-circuit current limiting and on-chip thermal shutdown help the device withstand bus contention without damage, as described in the Renesas ISL8485, ISL8490, and ISL8491 datasheet. The ISL8485CBZ uses a BiCMOS implementation and presents one unit load to the RS-485 bus. Its receiver and driver interface supports industrial communication equipment where compactness and data rate are important. Because the transceiver operates from a narrow 5 V supply range, the system must maintain 4.5 V to 5.5 V at the device for specified operation. Cabling, termination, grounding, and controlled edge rates remain important when maximizing channel integrity. Typical uses include industrial RS-485 controllers, building-automation equipment, factory data links, instrumentation gateways, and serial interface expansion for embedded processors. The 5 Mbps capability is useful for short, properly terminated links that need higher throughput than conventional slow-speed field-bus transceivers. For longer cables or lower data rates, engineers should also evaluate propagation delay, transceiver mode timing, and the loss budget of the selected cable. Place the transceiver close to the connector and bus interface to minimize unprotected trace length. Use a proper differential pair with consistent geometry, connect the receiver ground reference appropriately, and install termination only where dictated by the network topology. Decoupling capacitors should be positioned close to the supply and ground pins, while the driver-enable and receiver-enable timing must leave sufficient propagation delay for clean direction changes.

RFQ İletişim
ISL8485CP - 5V RS-485/RS-422 Transceiver | Renesas
ISL8485CP

ISL8485CP - 5V RS-485/RS-422 Transceiver | Renesas

Renesas ISL8485CP is a 5 V, low-power, half-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, supplied in an 8-pin through-hole PDIP package. It is designed for balanced industrial communication links where a single transceiver must support both differential transmit and receive operation. The verified distributor data identifies the device as a 1/1 RS-422 and RS-485 transceiver in an 8-PDIP package. A transceiver combines a differential line driver and differential receiver into one interface component. In the transmit direction, the driver converts a logic-level signal into a balanced differential voltage across a twisted-pair bus; in the receive direction, the receiver converts the differential bus voltage back into a logic-level signal. RS-422 commonly supports point-to-point, balanced signaling, while RS-485 permits multiple drivers and receivers on a shared bus when the system implements the required addressing, biasing, and contention controls. The ISL8485CP family is identified as a low-power 5 V RS-485/RS-422 solution with options described by the manufacturer as high-speed or slew-rate-limited. This distinction is important when designing a bus: slew-rate control can reduce high-frequency ringing and electromagnetic interference, while a high-speed configuration can improve propagation delay. The exact speed, slew-rate, output-current, and receiver-threshold limits are not present in the supplied verified excerpts and must be confirmed in the manufacturer datasheet before final circuit design. The device is implemented in an 8-PDIP package for through-hole assembly rather than a compact surface-mount land pattern. This makes it suitable for industrial controllers, data-acquisition equipment, instrumentation, and legacy interface boards where DIP soldering, prototyping, or through-hole serviceability is preferred. The balanced interface also helps reject common-mode noise when the transmitter and receiver reference a common signal ground and the cable routing is controlled. Typical applications include factory-floor serial links, industrial control modules, remote sensor interfaces, laboratory equipment, and building automation equipment. Designers should confirm the device's exact drive strength, receiver thresholds, data rate, enable or shutdown behavior, and bus termination requirements from the full datasheet. They should also verify whether a fail-safe receiver, ESD rating, slew-rate selection, or automotive qualification is required for the target environment. This page combines verified distributor availability, package information, pricing data, source links, and replacement analysis with practical RS-485 design guidance. It deliberately distinguishes confirmed facts from parameters that still require datasheet verification, helping engineers evaluate the ISL8485CP without mistaking incomplete web snippets for complete technical specifications.

RFQ İletişim
ISL8485ECB - 5V RS-485/422 Transceiver | Renesas
ISL8485ECB

ISL8485ECB - 5V RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8485ECB is a 5 V, low-power, half-duplex RS-485/RS-422 line transceiver in an 8-pin SOIC package. It combines one driver and one receiver, supports data rates up to 5 Mbps, and provides ESD protection to ±15 kV HBM. The device is designed for industrial and instrumentation links requiring a compact, high-speed differential transceiver. A line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives those differential signals back into CMOS-compatible logic. RS-485 and RS-422 belong to differential data-interface families. Their common-mode rejection and noise immunity make them useful for communications over cables, backplanes, and industrial control networks where signal integrity can be affected by motors, relays, and switching equipment. The ISL8485ECB operates from a 5 V supply and is identified as a one-driver, one-receiver, half-duplex RS-422/RS-485 device. It can operate as a high-speed transceiver or with slew-rate-limited signaling, allowing the same interface family to address EMC-sensitive links and longer, lower-speed connections. Its 8-pin SOIC package supports surface-mount assembly while retaining a widely used lead pitch. Electrical performance is centered on a maximum signaling rate of 5 Mbps and low power consumption. The ±15 kV HBM ESD rating protects the device from electrostatic discharge encountered during handling and field installation, although it does not replace proper surge-protection design for an installed cable. The receiver and driver combine in one package, reducing board area in nodes that need bidirectional bus communication. Typical applications include industrial sensor gateways, programmable logic controller communication, factory automation equipment, test and measurement instruments, building-control nodes, and RS-485 field-bus interfaces. In a half-duplex network, the transceiver can support bus management and point-to-point links when the application controls driver enable and receiver enable states. For PCB implementation, place the transceiver close to the connector or bus header and keep the differential route short and symmetric. Add the termination, biasing, common-mode protection, and decoupling components recommended by the manufacturer datasheet for the selected bus topology. Confirm driver-enable behavior so multiple transmitters do not contend on the same bus. This product page combines the manufacturer-device description, verified package and interface details, cross-reference findings, and application-specific design guidance to support faster component evaluation and replacement planning.

RFQ İletişim
ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas
ISL8485ECP

ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas

The Renesas Electronics ISL8485ECP is a single half-duplex RS-485 and RS-422 line transceiver IC operating from a 5 V supply and supplied in an 8-pin PDIP package. It combines one driver and one receiver in one device, supports ESD protection to ±15 kV, and includes driver short-circuit current limiting and on-chip thermal shutdown for improved robustness during bus contention. A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers. The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring. The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration. Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture. PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process. This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.

RFQ İletişim
ISL8485EIB - 5V RS-422/RS-485 Transceiver | Renesas
ISL8485EIB

ISL8485EIB - 5V RS-422/RS-485 Transceiver | Renesas

Renesas Electronics ISL8485EIB is a single-channel, half-duplex RS-422/RS-485 interface transceiver designed for 5 V systems, with a specified 4.5 V to 5.5 V supply range and an 8-pin SOIC package. The device combines a balanced line driver and differential receiver in one compact interface, supporting both RS-422 and RS-485 communication standards. An RS-485/RS-422 transceiver is an interface IC used to connect a controller, sensor, or communication equipment port to a balanced copper cable. The transceiver converts single-ended logic signals into differential bus signals and converts returning differential signals into a logic-level output. In the broader semiconductor hierarchy, it belongs to interface ICs, where differential transceivers support robust, noise-tolerant data links at relatively low bit rates. The ISL8485EIB provides ESD protection to ±15 kV on the driver outputs and receiver inputs without latch-up. Its BiCMOS construction supports low-power operation from a 5 V supply, while the high-speed ISL8485E configuration is intended for data rates through approximately 5 Mbps. Driver output short-circuit current limiting and on-chip thermal shutdown help protect the device during bus contention. The ISL8485 family differs from the slew-rate-limited ISL8483E family through its high-speed edge behavior. The faster transitions increase communication throughput, but they also produce more high-frequency content on the bus. Consequently, cable length, topology, termination, grounding, and electromagnetic compatibility requirements must be evaluated carefully rather than relying only on nominal data rate. Typical uses include industrial sensor networks, building automation equipment, process-control terminals, instrumentation links, and communication ports that need bidirectional half-duplex operation over a balanced bus. A single transceiver supports one physical bus channel, and multiple devices can be connected to an RS-485 segment when the system designer observes the applicable bus-loading and termination rules. PCB implementation should provide a solid ground plane, place the transceiver close to the connector or protected interface boundary, and route the balanced pair together with matched geometry. The 4.5 V to 5.5 V supply must remain within tolerance, and decoupling should connect directly to the device power and ground pins. External protection or isolation may still be required when exposed cables exceed the device’s specified ESD environment. This product page consolidates the electrical envelope, package details, application guidance, and verified drop-in alternatives for the ISL8485EIB. It also highlights the practical distinction between high-speed and slew-rate-limited Renesas transceivers so engineers can choose the interface behavior that best matches their cable, topology, and EMC requirements.

RFQ İletişim
ISL8485EIP - 5V RS-485/RS-422 Transceiver | Renesas
ISL8485EIP

ISL8485EIP - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8485EIP is a 5 V, single RS-485/RS-422 transceiver with integrated ESD protection, packaged in an 8-pin PDIP. It provides one half-duplex driver and receiver for balanced industrial communication links, accepts a supply range of 4.5 V to 5.5 V, and is designed for data rates up to 5 Mbps. Each driver output and receiver input is protected against ±15 kV ESD strikes without latch-up. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential balanced signals. RS-485 supports longer multipoint buses and common-mode noise tolerance, while RS-422 favors point-to-point, full-duplex communication. The ISL8485EIP belongs to the transceiver hierarchy: interface transceiver → differential line driver and receiver → communications interface IC. The principal benefits of the ISL8485EIP are its ±15 kV ESD protection, 4.5 V to 5.5 V supply tolerance, low-power BiCMOS implementation, and selectable high-speed or slew-rate-limited operation. Driver short-circuit current limiting and on-chip thermal shutdown improve robustness during bus contention. These characteristics suit equipment connected to industrial wiring where electrostatic discharge and ground-potential differences are common. The device supports both RS-485 and RS-422 balanced communication. Its driver outputs and receiver inputs are protected against ESD events, while the receiver can provide a fail-safe output when the bus is idle. The device operates from a single 5 V rail, allowing integration with conventional 5 V control logic. Exact propagation-delay, receiver-threshold, and load-current limits should be confirmed against the manufacturer datasheet before release. Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, data acquisition, and communications interfaces that require protection from cable-borne electrostatic discharge. The device is particularly useful where a 5 Mbps bus must tolerate electrical transients at exposed connector pins. PCB layout still requires a controlled return path and careful connection of the external interface network. Place protection and termination components close to the transceiver pins, route the differential pair as a tightly coupled pair, and provide a low-impedance ground reference. Respect the datasheet limits for driver load, receiver input, and supply bypassing. Keep analog and digital return currents separated where possible to reduce common-mode conversion and improve signal integrity. This page combines the manufacturer interface description, package information, sourcing data, and practical design guidance to support component selection. It also distinguishes the pin-compatible family alternatives from functionally similar devices that may require different package or operating details, helping engineers narrow a replacement without assuming interchangeability.

RFQ İletişim
ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IB

ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas

Renesas Electronics ISL8485IB is a single half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and a 5 V supply in an 8-pin SOIC package. The ISL8485IB uses BiCMOS technology and is specified for 4.5 V to 5.5 V power supplies, including the 10% supply tolerance identified on the Renesas product page. Its industrial temperature range extends from -40°C to +85°C. An RS-485/RS-422 transceiver is a differential communications interface IC that converts logic-level transmit and receive signals into balanced, noise-immune bus signals. The ISL8485 family supports both RS-485 half-duplex operation and RS-422 balanced operation. The ISL8485 configuration multiplexes its driver output and receiver input onto the same pair of bus terminals, allowing a compact eight-pin implementation. The principal features include a 5 Mbps maximum data rate, low-power BiCMOS construction, operation from a nominal 5 V rail, and a single-unit-load RS-485 bus interface. Half-duplex operation requires the design to control the driver-enable and receiver-enable functions so that the transmitter is disabled when the bus is not being driven. These characteristics make the device appropriate for industrial data links, instrumentation, factory equipment, and point-to-point or multidrop balanced communication. The ISL8485IB is one of three related devices: the ISL8485 provides half-duplex multiplexing, while the ISL8490 and ISL8491 provide separate receive and transmit paths for full-duplex applications. The Renesas ISL8485, ISL8490, and ISL8491 datasheet identifies these architectural differences explicitly. Because bus topology and enable logic affect protocol behavior, an existing PCB should be checked for pin functions before selecting a related family member. Typical installations include RS-485 industrial sensor networks, RS-422 controller-to-peripheral links, building-control equipment, and data-acquisition systems. The 5 Mbps capability supports faster communication than legacy low-speed RS-485 links, while the differential interface helps reject common-mode noise when the transceiver is used with correctly terminated cabling. Designers should verify the eight-pin pinout, supply decoupling, driver-enable sequencing, bus termination, and protection requirements against the manufacturer datasheet. Differential routing should use a controlled-impedance layout where practical, and the unused bus terminals must be handled according to the applicable RS-485 or RS-422 configuration. This page consolidates the verified Renesas and distributor information for the ISL8485IB, documents pin-compatible alternatives with their differences, and provides practical interface-design guidance that is not available from a distributor listing alone.

RFQ İletişim
ISL8485IB-T - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IB-T

ISL8485IB-T - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8485IB-T is a 5 V, low-power, half-duplex RS-485/RS-422 interface transceiver with a maximum data rate of 5 Mbps, packaged in an 8-pin SOIC. It provides one driver and one receiver for balanced serial communications and operates from a 4.5 V to 5.5 V supply, allowing operation with conventional 5 V power rails that may vary by 10%. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals to and from differential balanced pairs. The RS-485 standard supports multipoint buses and longer interconnects with excellent noise immunity, while RS-422 provides a point-to-point differential interface. The ISL8485 family is specified as a BiCMOS single-transceiver solution that can satisfy both interface types, making it useful where field buses, industrial controllers, and instrumentation share a common physical layer. The ISL8485IB-T operates from 4.5 V to 5.5 V and supports data rates up to 5 Mbps. It presents one unit load to an RS-485 bus, allowing up to 32 transceivers on the network when system loading and cabling conditions permit. Its half-duplex architecture reduces the number of external interface signals, while the 8-pin SOIC package supports compact surface-mount implementations. The BiCMOS architecture combines bipolar and CMOS characteristics to support the drive and receive functions required by balanced communication links. The device family includes high-speed and slew-rate-limited operating choices, so the appropriate variant should be selected according to edge-rate requirements, cable length, topology, and electromagnetic-emissions constraints. The IB designation identifies the slew-rate-limited family option rather than the fastest A-series option. Typical uses include industrial RS-485 field-bus links, building-control networks, factory equipment interfaces, data-acquisition systems, instrumentation, and communications equipment requiring a compact 5 V differential transceiver. Selection should account for bus direction control, termination, biasing, grounding, and the number of nodes connected to the same cable segment. For a new PCB, place the transceiver and its decoupling capacitor close to the supply pins, connect the differential pair as a controlled-impedance route, and keep the driver, receiver, and connector ground references in one continuous plane. Add termination only where required by the network topology and verify common-mode voltage, stub length, and radiated emissions in the final equipment. This product page combines the ISL8485 family electrical characteristics with package guidance, application analysis, and a parameter-focused comparison of compatible Renesas transceiver options. It is intended to help engineers narrow the choice before completing board-level timing, emissions, and fault-tolerance validation.

RFQ İletişim
ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IBZ

ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8485IBZ is a single half-duplex RS-485/RS-422 transceiver operating from a 4.5 V to 5.5 V supply, with a maximum data rate of 5 Mbps, in an 8-pin SOIC package. The device combines one driver and one receiver and presents one unit load to an RS-485 bus. An RS-485/RS-422 transceiver is a balanced data-communications interface that converts logic-level signals into differential bus signals and receives differential signals from the bus. These interface ICs belong to the transceiver hierarchy within interface integrated circuits and support robust point-to-point or multipoint communication over longer distances than conventional single-ended logic links. The ISL8485 family is specified for 10% supply tolerance, allowing operation across the 4.5 V to 5.5 V range. Its BiCMOS architecture supports data rates up to 5 Mbps, making the ISL8485IBZ useful for industrial control links, factory automation equipment, instrumentation, and other balanced-communication systems. The balanced interface also improves noise immunity in environments containing switching equipment and industrial motors. The ISL8485 is a half-duplex device, so the driver and receiver share the bus connection rather than operating simultaneously. System design must account for this shared use of the interface and provide the required direction-control function. The 8-SOIC outline supports compact, surface-mount PCB construction, although exact pin names and exposed-pad details should be confirmed against the manufacturer pin-description table before routing a new design. Typical uses include RS-485 links between controllers and sensors, communication between industrial modules, and RS-422-compatible point-to-point interconnects. The 5 Mbps maximum rate supports relatively fast control and data traffic, while the differential signaling method reduces susceptibility to common-mode noise. Cable length, topology, termination, grounding, and data rate must be considered together because faster operation generally imposes more restrictive channel requirements. For PCB implementation, place the transceiver close to the connector and route the balanced pair as a tightly coupled differential pair with continuous ground referencing. Use the termination and protection strategy appropriate for the installation, and keep switching-node currents away from the receiver path. This page also organizes lifecycle, sourcing, replacement, and application guidance around the manufacturer’s ISL8485 family information.

RFQ İletişim
ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IP

ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8485IP is a 5V, low-power, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5Mbps and supplied in an 8-pin DIP package. It provides one balanced transceiver interface for bidirectional multipoint data communication, places one unit load on an RS-485 bus, and operates from a supply range of 4.5V to 5.5V. The device is intended for industrial communication links requiring either high-speed operation or controlled slew rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential signals for balanced wired communication and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced links, while RS-485 permits multipoint buses and driver-enable control. The ISL8485IP belongs to the transceiver hierarchy within interface ICs and combines transmitter, receiver, bus-enable control, and protection functions in one package. Key features include a 5Mbps maximum data rate, 4.5V to 5.5V supply tolerance, one-unit-load bus loading, and support for both RS-485 and RS-422 signaling. The 8-pin DIP package is suitable for conventional through-hole assembly, prototyping, repair, and industrial control equipment. Its half-duplex arrangement allows the same differential pair to transmit and receive, although external direction-control logic is normally required. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation with high data-rate capability. According to the Renesas ISL8485 family information, the ISL8485, ISL8490, and ISL8491 devices are 5V-powered single transceivers that meet RS-485 and RS-422 standards. The family supports supply voltages with 10% tolerance and presents one unit load to the RS-485 bus, helping control loading when multiple nodes share a communication line. Typical applications include industrial factory automation, programmable-logic-controller communication, building-control networks, instrumentation links, and embedded serial-interface equipment. In these systems, the transceiver serves as the physical-layer interface between a controller UART or logic port and a balanced RS-485 or RS-422 cable. Its 5Mbps capability supports high-speed equipment links, while slew-rate-controlled variants in the broader family can be useful where lower EMI is the priority. PCB design should preserve the differential signal path and provide controlled termination and biasing appropriate to the selected RS-485 or RS-422 topology. Keep the transceiver close to the connector, route the differential pair as a coupled pair, and place termination components where they can be configured for the intended network. The maximum 5.5V supply is especially important in industrial systems because transients and supply tolerances must remain within the device rating. This product page combines verified distributor identification, package and interface details, family-level electrical characteristics, alternative sourcing information, and application-specific engineering guidance. It also distinguishes explicitly verified facts from parameters that require confirmation from the manufacturer datasheet before schematic release or production qualification.

RFQ İletişim
ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IPZ

ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

Renesas ISL8485IPZ is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin PDIP package. It operates from a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and combines one transmitter and one receiver in a single integrated circuit. The BiCMOS implementation supports balanced industrial-communication links where a compact, single-part interface is preferred. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as logic-level outputs. RS-422 provides a point-to-point balanced communication format, while RS-485 supports multipoint bus arrangements. The ISL8485IPZ belongs to the interface-IC hierarchy within integrated circuits and is used where electrical isolation, protocol conversion, or galvanic distance is handled elsewhere in the system. The principal operating features are a 4.5 V to 5.5 V supply range, operation to 5 Mbps, half-duplex communication, and one-unit-load RS-485 bus loading. These characteristics suit equipment that exchanges data over relatively short, high-speed balanced interconnects. The integrated transmitter and receiver reduce board area compared with separate driver and receiver circuits, while the PDIP package supports conventional through-hole assembly and prototyping. The BiCMOS architecture combines bipolar and CMOS circuit techniques, allowing the device to provide high-speed differential signaling while maintaining low-power interface operation. Half-duplex operation means the transmitter and receiver share the same differential pair, so the design must correctly manage driver-enable and receiver-enable controls to prevent unwanted bus contention. The one-unit-load rating permits multiple compatible transceivers to share an RS-485 network, subject to the total-load and topology limits of the completed bus. Typical uses include industrial control equipment, factory automation links, data-acquisition equipment, instrumentation, and communications modules that connect a host controller to an RS-485 or RS-422 peripheral. The 5 Mbps capability is useful for short links carrying frequent control or diagnostic messages, although cable length, topology, termination, grounding, and transceiver delay determine the practical communication distance. Designers should place the transceiver near the connector and cable entry point, provide the required supply and bypass capacitance, and follow the manufacturer datasheet for driver-enable and receiver-enable logic. Differential pairs should be routed with consistent geometry and controlled impedance. A termination resistor is normally placed at each end of an RS-422 link; RS-485 termination practices depend on the bus topology and its signal reflections. This page combines the exact Renesas product characteristics, package information, pricing evidence, interface-family relationships, comparison parameters, and practical implementation guidance. It also distinguishes verified drop-in alternatives from near-equivalent devices that use a different package and therefore require PCB redesign rather than simple component substitution.

RFQ İletişim