Renesas Electronics

ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas

MPN: ISL8483EIP ✓ Aktif
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin PDIP Package
MOQ: 1 |

ISL8483EIP Genel Bakış

The Renesas Electronics ISL8483EIP is a 5 V, single-channel RS-485/RS-422 interface transceiver with one transmitter and one receiver, packaged in an 8-pin PDIP. It provides ±15 kV ESD protection at the driver outputs and receiver inputs, combines BiCMOS circuitry with short-circuit current limiting, and includes on-chip thermal shutdown for dependable operation during bus contention.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and longer distances. RS-422 emphasizes point-to-point, balanced signaling, while RS-485 supports multidrop buses and driver-enable control. This device bridges the single-ended digital domain and the differential bus, placing it within the interface IC, communication IC, and semiconductor hierarchy.

Key features include one half-duplex transmitter, one receiver, 5 V operation, and device-level ESD protection of ±15 kV. Driver short-circuit current limits help protect the outputs when a bus node is driven against another active node. Thermal shutdown adds a secondary protection mechanism when sustained contention or abnormal loading raises internal dissipation.

The ISL8483 family combines BiCMOS implementation with low-power operation and two signal-rate options identified by the ISL8483 and ISL8485 family members. The E version adds enhanced ESD protection, while the receiver and driver control arrangement supports implementation of half-duplex nodes. Exact data rate, propagation delay, slew rate, and common-mode limits should be selected from the family datasheet for the intended bus topology.

Typical uses include industrial RS-485 field buses, building automation equipment, factory data links, RS-422 point-to-point links, and industrial control modules. The device is particularly suitable when a design needs a single transceiver, balanced differential signaling, 5 V supply operation, and reinforced ESD protection near a connector or externally accessible cable.

PCB implementation should keep the transceiver close to the connector, route the differential pair as a tightly matched pair, and provide a low-impedance return path. Decoupling capacitors should connect to the ground plane with short traces, and unused or unused-condition control inputs must be driven to defined logic levels to prevent an indeterminate bus state.

Drop-in alternatifler için ISL8483EIP — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller ISL8483EIP (aynı form faktörü ve ayağa oturma) — farklı olan Mounting Type, Package, ESD Protection, Product Type.

Renesas Electronics
Mounting Type: Surface mount
Package: 8-pin SOIC
ESD Protection: ±15 kV on driver outputs and receiver inputs
İle Karşılaştır ISL8483EIP →
Renesas Electronics
Mounting Type: Through hole
Package: 8-PDIP
Product Type: RS-485/RS-422 transceiver
İle Karşılaştır ISL8483EIP →

ISL8483IP

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Renesas Electronics
📦 8-pin PDIP
RS-485/RS-422 transceiver · 1 transmitter and 1 receiver · Half duplex · 250 kbps · 5 V · High speed or slew-rate limited · Yes · Yes

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

ISL8483CP

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin PDIP
Same ISL8483 PDIP pinout and 5 V transceiver architecture, with the C variant intended for different slew-rate or signal-rate characteristics; exact timing must be checked

📋 Katalogda Olmayan Referans Alternatifi

ISL8485EIP

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin PDIP
Same 5 V, ±15 kV ESD-protected PDIP transceiver family, but receiver and signal-rate characteristics differ from ISL8483EIP

📋 Katalogda Olmayan Referans Alternatifi

ISL8483EIP Özellikler

Device Type Single RS-485/RS-422 transceiver
Transmitter and Receiver Count 1 transmitter and 1 receiver
Besleme Gerilimi 5 V
ESD Protection ±15 kV
Supported Standards RS-485 and RS-422
Implementation Technology BiCMOS
Driver Short-Circuit Protection On-chip short-circuit current limiting
Thermal Protection On-chip thermal shutdown
Paket 8-pin PDIP
Pin Sayısı 8 pins
Montaj Türü Through-hole
RoHS Durumu Compliant

ISL8483EIP Pin Yapısı

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 ROUT — Receiver output
Pin 2 RE — Receiver enable input
Pin 3 DE — Driver enable input
Pin 4 DI — Driver input
Pin 5 GND — Ground
Pin 6 A — Differential driver output A
Pin 7 B — Differential driver output B
Pin 8 VCC — Positive supply voltage

Tipik Uygulamalar

ISL8483EIP için uygundur 6 uygulamas: Industrial RS-485 Field Bus, RS-422 Point-to-Point Link, Building Automation Controller, Factory Data Acquisition Equipment, Industrial Control Module, External Communication Connector.

🏭

Industrial RS-485 Field Bus

The ISL8483EIP is appropriate for a half-duplex industrial RS-485 node because it combines one transmitter, one receiver, 5 V operation, and ±15 kV ESD protection in an 8-pin PDIP package. Place the transceiver between the controller UART and the isolated or non-isolated bus connector, using the enable controls to prevent more than one node from driving the bus simultaneously. Its short-circuit current limiting and thermal shutdown improve robustness during contention. The exact maximum data rate and bus length must be selected from the datasheet for the installed cable, termination, topology, and common-mode environment.

🌐

RS-422 Point-to-Point Link

The ISL8483EIP can terminate a point-to-point RS-422 link when the design uses a single balanced channel and 5 V interface voltage. The transmitter converts the UART logic signal into differential bus levels, while the receiver returns a single-ended signal to the controller. Driver-enable and receiver-enable pins support controlled half-duplex operation where both directions are not required simultaneously. The ±15 kV ESD rating is valuable near an external connector, although cable routing, grounding, and the exact receiver thresholds remain critical to reliable communication.

🧩

Building Automation Controller

Building automation controllers often distribute sensor and actuator commands over RS-485 wiring that may pass near doors, lighting panels, and maintenance interfaces. The ISL8483EIP offers a compact 8-pin PDIP implementation with 5 V operation and ±15 kV protection against ESD encountered at external wiring points. Its one-driver, one-receiver configuration is suitable for a half-duplex controller node, while short-circuit limiting and thermal shutdown help the interface survive bus conflicts. Final qualification should include the controller's UART timing, termination strategy, grounding arrangement, and applicable building-system EMC requirements.

🏭

Factory Data Acquisition Equipment

Factory acquisition equipment can use the ISL8483EIP to connect a controller to remote sensors, counters, or programmable instruments over a balanced RS-485 bus. The transceiver's single transmitter and receiver reduce the interface footprint, while the 5 V supply requirement supports integration into conventional embedded control hardware. ESD protection is important when acquisition modules connect to long cables or user-accessible equipment. Designers should still verify propagation delay against the required polling rate, account for bus-stub reflections, and provide the termination and biasing required by the selected network topology.

⚡

Industrial Control Module

The ISL8483EIP is suitable for a compact industrial control module that exchanges commands and diagnostic data over a wired RS-485 or RS-422 link. Its through-hole 8-pin PDIP package supports conventional plated-through-hole assembly and rework, while the 5 V operating rail simplifies integration with logic powered from the same supply. Connecting the transceiver close to the field connector helps direct ESD currents away from sensitive controller circuitry. The control firmware should enforce bus-enable arbitration, and the hardware design should verify receiver fail-safe behavior, driver loading, and thermal performance at the intended ambient temperature.

🔧

External Communication Connector

An external communication connector exposed to cables and service access is a common ESD entry point for electronics. Placing the ISL8483EIP near that connector provides ±15 kV ESD protection on the driver outputs and receiver inputs, reducing stress on the controller and isolating the digital logic from the balanced bus. The 8-pin PDIP package offers a straightforward through-hole implementation, and the short-circuit-limited driver helps manage accidental bus conflicts. For reliable protection, use the shortest practical route to the connector, maintain a continuous ground reference, avoid stubs, and follow the datasheet's recommended bus-side layout.

Önerilen Ürünler Özeti

ISL8483EIP Renesas Electronics Kullanıldığı Yer: Industrial RS-485 Field Bus, RS-422 Point-to-Point Link, Building Automation Controller, Factory Data Acquisition Equipment, Industrial Control Module, External Communication Connector ISL8483IP Renesas Electronics Kullanıldığı Yer: Industrial RS-485 Field Bus, Building Automation Controller ISL8485EIP Same-family alternative for different timing requirements Kullanıldığı Yer: Industrial RS-485 Field Bus, RS-422 Point-to-Point Link, Factory Data Acquisition Equipment, External Communication Connector ISL8483CP Same-family alternative for different bus timing Kullanıldığı Yer: Building Automation Controller, Industrial Control Module
What is the ISL8483EIP?
The ISL8483EIP is a 5 V, single-channel RS-485/RS-422 transceiver containing one driver and one receiver in an 8-pin PDIP package. According to the Renesas ISL8483E/ISL8485E datasheet, the device is ESD protected to ±15 kV, uses BiCMOS circuitry, limits driver output current during bus contention, and includes on-chip thermal shutdown.
What are the key specifications of ISL8483EIP that engineers should know?
The ISL8483EIP combines a 5 V supply, one RS-485/RS-422 transmitter, one receiver, and ±15 kV ESD protection in an 8-pin PDIP. The Renesas ISL8483E/ISL8485E datasheet also identifies BiCMOS implementation, driver short-circuit current limiting, and thermal shutdown as key protection features. Maximum data rate, propagation delay, slew rate, and temperature limits must be checked in the device datasheet.
Where to download the ISL8483EIP datasheet PDF?
The official ISL8483E/ISL8485E datasheet is available from the Renesas Electronics document center at the product's datasheet URL. Use the manufacturer's document for the final pin description, electrical characteristics, timing values, recommended operating conditions, and application circuit. A mirrored Mouser PDF is also listed, but the Renesas document should be preferred for revision control.
Where can I find the ISL8483EIP pinout?
The ISL8483EIP pinout is shown in the pin-description section of the Renesas ISL8483E/ISL8485E datasheet. The 8-pin PDIP provides the receiver output, receiver-enable and driver-enable controls, driver input, ground, differential driver terminals, and supply. When assigning PCB tracks, use the datasheet pin-description table and preserve the exposed-pad convention only if the selected package variant actually has one.
Does the ISL8483EIP support both RS-485 and RS-422?
Yes, the ISL8483EIP supports balanced RS-485 and RS-422 communication. According to the Renesas ISL8483E/ISL8485E datasheet, these devices are ESD-protected, BiCMOS, 5 V-powered single transceivers designed for both standards. In practice, RS-485 allows multidrop bus operation and driver control, whereas RS-422 is commonly used for point-to-point links.
What ESD protection does the ISL8483EIP provide?
The ISL8483EIP provides ±15 kV ESD protection on the driver outputs and receiver inputs. The manufacturer describes the ISL8483E and ISL8485E devices as BiCMOS, 5 V transceivers whose external signal paths are protected against ±15 kV ESD strikes without latch-up. Placement near an exposed connector can help route surge current through the intended protection path.
What happens when an RS-485 driver output is shorted?
The ISL8483EIP limits driver short-circuit current when a bus output is driven against another active node. The Renesas ISL8483E/ISL8485E datasheet states that the devices meet the RS-485 requirement to survive worst-case bus contention without damage. On-chip thermal shutdown provides an additional response to excessive internal dissipation, although the design should still prevent sustained contention.
Is the ISL8483EIP suitable for industrial RS-485 equipment?
The ISL8483EIP is well suited to industrial RS-485 equipment requiring balanced signaling, 5 V operation, and connector-level ESD protection. Its ±15 kV protection rating, driver short-circuit limiting, and thermal shutdown address common field-bus hazards. The final suitability depends on the required operating temperature, data rate, bus length, noise margin, isolation needs, and EMC test level.
Where to buy ISL8483EIP online?
Use the Request a Quote form on this page to request ISL8483EIP availability, order quantity, and current lead time. The form lets you specify the required quantity and package without relying on a static distributor listing. The target is an 8-pin PDIP RS-485/RS-422 transceiver, so confirm that the requested suffix and package match ISL8483EIP before placing an order.
What is the price of ISL8483EIP?
The current unit price for ISL8483EIP is obtained through the Request a Quote form on this page. The structured pricing interface reflects changing commercial conditions and quantity breaks without embedding a potentially stale price in the technical description. Submit the required order quantity and application information so the offer can be matched to the exact 8-pin PDIP device.
What is the lead time and stock status for ISL8483EIP?
The current stock position and lead time for ISL8483EIP should be confirmed through the Request a Quote form on this page. Commercial availability can change by package, quantity, and manufacturing status, so a listing snapshot should not be treated as a firm allocation. Include the target quantity, delivery location, and required production schedule in the request.
What can replace the ISL8483EIP?
The closest same-family replacement choices are the PDIP versions of ISL8483, ISL8483C, and ISL8485E, subject to verifying their exact drive, slew-rate, and receiver specifications against the original design. The ISL8483EIP offers a one-transmitter, one-receiver, 5 V configuration with ±15 kV ESD protection. A replacement is truly drop-in only after the package, pin functions, logic levels, timing, and protection ratings are checked.
Can ISL8483IP replace ISL8483EIP?
ISL8483IP can serve as a candidate replacement because it belongs to the same ISL8483 PDIP family, but it is not automatically an exact substitute for ISL8483EIP. The ISL8483EIP explicitly provides ±15 kV ESD protection, while the E designation is absent from ISL8483IP. Confirm the alternative's ESD rating, timing, slew rate, enable polarity, and operating temperature before approving it.
ISL8483EIP vs ISL8485EIP - which is better for a low-speed RS-485 bus?
The ISL8483EIP and ISL8485EIP share the 5 V, single-transceiver, 8-pin PDIP format and enhanced ESD-protection family characteristics, but their family positions indicate different signal-rate tradeoffs. For a low-speed bus, select according to the datasheet's receiver timing, driver slew rate, propagation delay, and intended noise-immunity requirements. The ISL8485E may be considered when its family-specific behavior better matches the bus.
Is the ISL8483EIP the same as an RS-485 interface IC from another manufacturer?
No, the ISL8483EIP should not be treated as identical to another manufacturer's transceiver merely because both support RS-485. A true drop-in substitute needs the same 8-pin PDIP footprint, matching pin functions, compatible 5 V operation, compatible receiver thresholds, equivalent driver and receiver timing, and suitable protection. Cross-brand candidates must also be checked for shutdown, fail-safe bias, and propagation-delay differences.

Mühendislik referans verileri: ISL8483EIP — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the ISL8483EIP for a 5 V half-duplex RS-485 or RS-422 node that needs one transmitter, one receiver, and an explicitly specified ±15 kV ESD protection rating. Its 8-pin PDIP footprint also suits through-hole assembly and design reuse. Select ISL8483IP when a non-E family version is acceptable, but verify its ESD rating and timing against the original design. Consider ISL8483CP when slew-rate-limited behavior is preferable to the high-speed ISL8483E profile. Use ISL8485EIP when its receiver and timing characteristics provide a better match to the bus. Before approving any substitution, compare pin functions, supply current, logic thresholds, propagation delay, driver loading, fail-safe behavior, operating temperature, and protection ratings. A same-package designation alone does not establish functional interchangeability.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün ISL8483IP ISL8483CP ISL8485EIP
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Transmitter and Receiver Count 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver
Supply Voltage 5 V 5 V 5 V 5 V
Supported Standards RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422

Ana Farklılayıcılar

  • Enhanced ESD protection in the E-version (karşılaştırma:ISL8483IP)
  • Direct same-package family interchange (karşılaştırma:ISL8485EIP)
  • Choice of signal-rate behavior without changing the footprint (karşılaştırma:ISL8483CP)

Tasarım Notları

Place the ISL8483EIP close to the external connector so ESD and cable-transient currents are intercepted before reaching the controller. Route the A and B conductors as a matched differential pair over a continuous ground plane, keep the pair length uniform, and avoid stubs. Connect the transceiver ground pins directly to the ground plane with short paths rather than routing return current through the differential pair.

Decouple the 5 V supply at the transceiver with a short trace to the ground plane. Keep the supply and ground connections away from the A and B bus traces to minimize differential crosstalk. Provide local bypass capacitance according to the family datasheet and ensure the supply source can support the transmitter's enabled load and the receiver's operating current without excessive rail droop during data transmission.

Do not allow more than one node to enable its driver simultaneously. The RS-485 bus can sustain contention, and the ISL8483EIP includes short-circuit current limiting and thermal shutdown, but sustained contention still wastes power and creates thermal stress. Use deterministic enable control in firmware, define a safe state for the enable inputs during reset, and avoid floating control or logic inputs.

Choose the family variant according to the required edge rate rather than selecting solely by maximum data rate. Faster slew rates can reduce cable-related signal loss but may increase emissions and common-mode disturbance; a slew-rate-limited version can be preferable on slower or noisier industrial wiring. Confirm propagation delay, receiver threshold, bus loading, termination, and biasing together before freezing the PCB design.

Thermal shutdown is a fault-protection feature rather than a substitute for correct bus arbitration. Verify continuous transmitter current, ambient temperature, and package dissipation for the selected operating mode. If the driver can remain enabled during repeated bus conflicts, consider system-level mitigation such as controlled shutdown, fault monitoring, or a physical bus design that prevents simultaneous active drivers.

Uyumluluk Bilgisi

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The product listing identifies the ISL8483EIP as RoHS compliant. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification information is stated for this exact suffix.

Veri doğrulanma tarihi: 2026-11-15 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

ISL8483EIP datasheet ISL8483EIP datasheet pdf ISL8483EIP pinout ISL8483EIP specifications Renesas ISL8483EIP ISL8483EIP RS-485 transceiver ISL8483EIP PDIP-8 ISL8483EIP equivalent ISL8483EIP replacement ISL8483EIP vs ISL8485EIP ISL8483EIP application circuit ISL8483EIP price ISL8483EIP stock ISL8483EIP cross reference

İlgili Bileşenler ve Terimler

Renesas Electronics ISL8483EIP ISL8483IP ISL8483CP ISL8485EIP RS-485 RS-422 transceiver interface IC communication IC balanced differential signaling half-duplex communication BiCMOS ESD protection driver short-circuit current limiting thermal shutdown 8-pin PDIP through-hole package industrial field bus building automation data acquisition 5 V power supply ±15 kV ESD
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle