Ürünler (46.000+)

LM2901SNG - Quad Comparator, ±18V/36V, 14-PDIP | onsemi
LM2901SNG

LM2901SNG - Quad Comparator, ±18V/36V, 14-PDIP | onsemi

The onsemi LM2901SNG is a quad general-purpose analog comparator in a 14-pin PDIP package, with four independent comparator channels and a stated supply-voltage capability of ±18 V, or 36 V total. It is designed for general-purpose signal comparison across industrial, automotive, and consumer circuits. An analog comparator is a semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2901 family combines four independent comparator channels on one monolithic integrated circuit. Its common-mode input range includes ground, allowing the device to operate from single-supply or dual-supply arrangements while comparing signals near 0 V. The LM2901SNG supports general-purpose comparison with an open-collector output structure, as identified in manufacturer-family information for the LM2901 series. Open-collector outputs require an external pull-up resistor and allow several outputs to be wired together when the system needs a wired-AND function. Each channel has independent inputs, making the quad configuration useful when four threshold decisions are required in one package. A typical implementation places a reference voltage on one input and a sensor or divided signal on the other. The comparator output changes state when the signal crosses the reference. Because comparator accuracy and behavior depend on input common-mode voltage, supply voltage, output pull-up value, and source impedance, designers should consult the onsemi LM2901 datasheet for recommended operating conditions and electrical characteristics. Typical uses include industrial sensor thresholding, battery voltage monitoring, overvoltage and undervoltage detection, window-comparison circuits, and general control logic. The 14-pin PDIP format is particularly suitable for through-hole industrial assemblies, prototypes, repair work, and educational platforms where socketed components or easy inspection are preferred. When laying out a circuit, place input resistors close to the relevant comparator pins and route the open-collector output away from high-impedance analog inputs to reduce switching transients. Select the pull-up resistor for the required sink current and logic family, and account for the output's open-collector state during fault analysis. This product record combines the onsemi family description, package information, source references, drop-in candidates, and practical design guidance. It also distinguishes true 14-pin PDIP replacements from similarly named devices offered in SOIC or other packages, helping engineers evaluate PCB compatibility before making a design change.

RFQ İletişim
LM2901VD - 36V Quad Differential Comparator | onsemi
LM2901VD

LM2901VD - 36V Quad Differential Comparator | onsemi

The onsemi LM2901VD is a four-channel differential comparator designed for level detection, low-level sensing, and memory applications, with a 3 V to 36 V operating range and a typical input bias current of 25 nA. The device is packaged in a 14-pin SOIC and provides open-collector outputs suitable for wired logic interfaces. Each of the four independent comparators compares its non-inverting and inverting inputs and produces a logic-level indication of their relative voltages. A differential comparator is an analog interface IC that converts the relationship between two input voltages into a digital output. In the broader semiconductor hierarchy, the LM2901VD belongs to the comparator family, which sits alongside amplifiers and other interface ICs. It is used where a system must establish whether a measured voltage is above or below a reference, such as in power-supply threshold detection, signal conditioning, and simple control systems. Key features include single-supply or split-supply operation, a typical input bias current of 25 nA, and a typical input offset current of ±5.0 nA. The low input bias current reduces loading on high-impedance source circuits, which is useful when the comparator monitors a sensor or resistor-divider output. The wide 3 V to 36 V supply range supports industrial control systems, automotive equipment, consumer products, and embedded memory interfaces. The open-collector output architecture requires an external pull-up resistor and permits the output to be pulled to a selected logic voltage. This feature enables connection to TTL-compatible systems and allows multiple comparator outputs to share a bus when suitable wired logic behavior is acceptable. The four independent channels can perform separate threshold, window, or sensing functions without sharing an internal signal path. Typical applications include overvoltage and undervoltage detection, battery monitoring, industrial sensor interfaces, memory address decoding, automotive logic systems, and general-purpose control equipment. Because the output is open collector, designers should account for pull-up resistor selection, output rise time, bus capacitance, and the voltage and current ratings of the pull-up network. The principal design consideration is common-mode and supply compatibility. Input and output conditions must remain within the limits stated in the manufacturer datasheet, and the external pull-up must not exceed the output transistor's voltage rating. The 14-pin SOIC footprint also requires adequate spacing between adjacent analog inputs to reduce noise coupling. This page combines the manufacturer function description, package information, electrical highlights, verified sourcing links, drop-in comparison options, and practical circuit-design guidance to support faster component evaluation and PCB planning.

RFQ İletişim
LM2901VDG - 3-36V Quad Differential Comparator | onsemi
LM2901VDG

LM2901VDG - 3-36V Quad Differential Comparator | onsemi

The onsemi LM2901VDG is a quad differential comparator containing four independent general-purpose comparator channels, each with CMOS, open-collector, and TTL-compatible output, in a 14-SOIC package. It operates from 3 V to 36 V in a single-supply configuration or from ±1.5 V to ±18 V in a dual-supply configuration, and its extended-temperature operating range is -40°C to +125°C. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four channels are electrically independent, allowing a single package to implement four threshold, level-detection, sensing, or monitoring functions while sharing a common power supply and ground. The LM2901VDG combines a 2 mV offset specification with 25 nA input-bias current, low supply-current drain, and a wide operating-supply range. Each open-collector output can interface with TTL, CMOS, and MOS logic. A 0.8 mA typical supply-current drain and supply-independent current consumption make the device suitable for systems where predictable current use is important across a broad supply range. The V-suffix family is specified for extended temperature operation. The manufacturer datasheet identifies tested operating limits of 30 V for the relevant device family and describes single-supply or dual-supply operation. Because the outputs are open collector, external pull-up resistors are required when the outputs must drive a high logic level, and the pull-up voltage and sink-current capability must be checked against the connected logic load. Typical uses include industrial voltage-threshold detection, low-level sensing, consumer equipment, automotive interface functions, and memory-control logic. Its four independent channels can monitor several control signals simultaneously, while the broad supply range permits operation from low-voltage single supplies to higher-voltage split rails. The same-package footprint also supports comparator consolidation when a board requires more than one sensing channel. For PCB implementation, place bypass capacitance close to the supply and ground pins, route each high-impedance input away from switching nodes, and use the pull-up resistor to establish the required output rise time. Because open-collector outputs can pull only to a low state, omit pull-up resistors only when another device provides the required active pull-up. Check input common-mode limits, output timing, and absolute maximum voltage before connecting external signals. This product page combines the manufacturer's device information with practical comparison, application, pinout, and PCB-design guidance. It helps engineers evaluate the LM2901VDG as a four-channel general-purpose comparator while preserving the distinction between verified electrical limits, device-family information, and design decisions that must be confirmed against the manufacturer datasheet.

RFQ İletişim
LM2901VN - Quad 36V Comparator | onsemi | Through-Hole
LM2901VN

LM2901VN - Quad 36V Comparator | onsemi | Through-Hole

The onsemi LM2901VN is a quad differential voltage comparator with four independent channels, a 3 V to 36 V supply range, open-collector outputs, and a 14-pin PDIP package. The device is designed for general-purpose voltage comparison in industrial, automotive, power-control, and signal-conditioning systems, including applications where the input common-mode range extends to ground. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The comparator belongs to the broader signal-conditioning and interface hierarchy: voltage comparator, analog interface IC, semiconductor, and electronic component. Each LM2901VN channel provides inverting and non-inverting inputs, an output, and access to the ground reference. Its open-collector outputs allow wired-OR operation and require an external pull-up resistor when driving a logic input. Key features include four independent comparison channels in one package, operation from 3 V to 36 V, open-collector sinking capability, and a common-mode input voltage range that includes ground. The package is a 14-pin through-hole PDIP. Because the outputs are open collector, engineers can choose the pull-up voltage independently of the comparator supply when logic-interface requirements differ, while ensuring that the selected resistor and output transistor stay within their current limits. The LM2901VN provides the familiar LM2901 channel arrangement, with each comparator using separate input and output pins. Its monolithic construction places four independent channels on one substrate, reducing component count in designs that require multiple threshold, window, overvoltage, or undervoltage decisions. The wide operating supply range supports both low-voltage logic rails and higher-voltage industrial or automotive systems when the associated input and output ratings are respected. Typical uses include power-supply sequencing, battery monitoring, motor-control feedback, sensor threshold conditioning, industrial control logic, and automotive signal comparison. In a power-supply circuit, one channel can monitor a feedback-derived voltage against a reference while another channel supervises another rail. In a motor-control application, the comparator can evaluate a scaled current or position signal before driving a control transistor through an external interface stage. Designers should verify input and output voltage limits for the specific operating condition, account for the open-collector pull-up network, and ensure logic compatibility with the driven device. A pull-up resistor sets rise time and current, so it should be selected from the required sink-current and propagation-delay limits. Breadboard and prototype layouts should keep each comparator's input path short and away from noisy switching nodes to reduce false transitions. This product record combines the LM2901VN device identity, verified 3 V to 36 V and 14-pin PDIP characteristics, package-specific replacement guidance, comparison parameters, and practical circuit-design guidance. It is intended to support component selection, PCB-level replacement decisions, and application design without obscuring the differences between same-family and cross-manufacturer alternatives.

RFQ İletişim
LM2901VNG - Quad 36V Open-Collector Comparator | onsemi
LM2901VNG

LM2901VNG - Quad 36V Open-Collector Comparator | onsemi

onsemi LM2901VNG is a general-purpose quad differential comparator containing four independent voltage comparators in a 14-pin PDIP package. Each comparator supports single-supply operation from 3 V to 36 V or dual-supply operation from ±1.5 V to ±18 V, while its open-collector output supports wired-AND operation and compatibility with TTL, CMOS, and MOS logic levels. The device is intended for level detection, low-level sensing, memory applications, consumer equipment, automotive electronics, and industrial control systems. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. Within the broader semiconductor hierarchy, the LM2901VNG belongs to the comparator and amplifier-IC family. Its four independent channels allow one package to monitor four thresholds or implement four independent protection functions. Unlike an op-amp, each channel uses open-collector output transistors, so an external pull-up resistor is required to establish a high output voltage. Key electrical characteristics include a maximum supply voltage of 36 V, a single-supply operating range of 3 V to 36 V, an input bias current as high as 0.25 µA, and an open-collector output architecture. The V suffix identifies the higher-performance grade in the LM2901 family, while NG identifies the onsemi 14-pin PDIP package. The through-hole package supports conventional insertion into a PCB and is available in tube packaging according to the manufacturer distribution information. The comparator architecture supports sensing signals around the supply rails, including low-level and zero-cross detection. Input stages compare a non-inverting input with an inverting input, and the output transistor changes state as the differential input crosses the comparator threshold. Because the outputs are open collector, multiple channels may share a pull-up resistor and form a wired-AND arrangement. The external pull-up must be sized for the logic family, leakage current, switching speed, and fan-out requirement rather than treated as a fixed output impedance. Typical uses include industrial sensor interfaces, automotive battery and power-system monitoring, consumer threshold detection, memory-device control, and four-channel supervision in industrial automation. The wide 3 V to 36 V single-supply range also permits operation from regulated 5 V and 12 V rails as well as industrial 24 V systems when the applied voltages remain within the rated limits. PCB design should reserve the correct 14-pin PDIP footprint, provide a continuous ground path, and place the output pull-up resistors close to the comparator pins to limit switching-loop area. Input traces should be kept away from high-current switching nodes and output return currents. Because the LM2901VNG is a through-hole analog device, additional filtering is generally required when sensing noisy sensor nodes rather than relying on comparator hysteresis alone. This page combines manufacturer and distributor information with application guidance, comparison criteria, and drop-in replacement research. It highlights electrical limits and package compatibility so engineers can distinguish a true pin-compatible substitution from a merely similar quad comparator before releasing a new PCB.

RFQ İletişim
LM2902AMX - Quad 14-SOP Op Amp | onsemi | Signal Control
LM2902AMX

LM2902AMX - Quad 14-SOP Op Amp | onsemi | Signal Control

The onsemi LM2902AMX is a general-purpose quad operational amplifier in a 14-pin SOP package, providing four amplifier circuits with a 40 nA input bias current for industrial signal-conditioning, instrumentation, and low-voltage analog systems. The device is identified as a standard general-purpose amplifier with four circuits in a 14-SOP package, making it suitable for designs that need several amplifier channels while controlling component count and board area. An operational amplifier is an analog amplifier that uses very high open-loop gain and negative feedback to amplify small voltage differences. The quad LM2902AMX places four amplifiers in one package, each with its own two inputs and one output while sharing the supply pins. Within the product taxonomy, it is an operational amplifier within the broader amplifier IC and analog signal-processing categories. The LM2902AMX is specifically identified as a standard general-purpose amplifier, which makes it appropriate for buffering, current-to-voltage conversion, differential amplification, level shifting, and feedback-control circuits. Its 40 nA input bias current supports applications in which bias-related error must remain controlled around sensitive analog nodes. The 14-SOP package also provides a conventional surface-mount option for industrial, instrumentation, and embedded control equipment. Because four amplifier sections share one package, the device can reduce component count and simplify routing in multi-channel analog boards. Typical uses include amplifier banks in control panels, sensor conditioning channels, active filtering, and low-frequency analog signal processing. Designers should confirm input common-mode range, output swing, supply-voltage limits, offset voltage, input offset current, unity-gain bandwidth, slew rate, noise, and temperature limits against the manufacturer datasheet before finalizing a design. The principal design trade-off is that a general-purpose quad amplifier prioritizes flexibility and channel density rather than the very low offset, low noise, high bandwidth, or rail-to-rail performance available from specialized amplifier families. Applications operating from a single supply, near the positive rail, or with very small sensor signals may require additional output biasing or a different amplifier architecture. Decoupling capacitors, input protection, output loading, and stability with capacitive loads must also be evaluated per circuit. This page combines package and catalog information with application guidance, drop-in replacement comparisons, and practical design notes. It is intended to help engineers qualify the LM2902AMX for industrial analog boards faster than by reading the datasheet and distributor listings separately.

RFQ İletişim
LM2902AQS14-13 - Quad 36V Automotive Op Amp | Diodes
LM2902AQS14-13

LM2902AQS14-13 - Quad 36V Automotive Op Amp | Diodes

Diodes Incorporated LM2902AQS14-13 is a four-circuit general-purpose operational amplifier designed for automotive-compliant applications, with a 3V to 36V single-supply range, a 20 nA input bias current, and a 14-pin SOIC package. The amplifier combines approximately 1 mV typical input offset voltage, 100 dB DC voltage gain, and 700 kHz unity-gain bandwidth in one package. An operational amplifier is a voltage-gain circuit that compares an inverting input with a non-inverting input and drives its output toward the difference between them. Operational amplifiers belong to the broader analog IC and signal-conditioning hierarchy. They are commonly used for sensor amplification, error amplification, voltage buffering, filtering, and analog-to-digital converter input conditioning. The LM2902 family is intended for general-purpose designs where four amplifiers and relatively wide supply-voltage tolerance provide more utility than a single precision amplifier. The principal electrical features include a 3V to 36V single-supply operating range, operation from ±1.5V to ±18V on dual supplies, and supply-current drain that is largely independent of supply voltage. Each amplifier supports rail-to-rail input operation, has a typical input bias current of 20 nA, and offers a typical open-loop DC gain of 100 dB. The temperature-compensated unity-gain bandwidth is 700 kHz, while the listed slew rate is 0.3 V/µs. The A-grade offset specification is 1 mV typical, making the device suitable for general signal-conditioning applications that do not require the tighter matching of a precision instrumentation amplifier. Internally compensated amplifiers simplify closed-loop gain selection, and the four independent channels can implement separate gain, filtering, comparison, buffering, or feedback functions. Their broad supply range also permits operation from industrial 24V supplies when designers observe the absolute maximum and common-mode limits. Typical uses include automotive sensor interfaces, industrial control loops, battery-powered instrumentation, transducer signal conditioning, low-current motor control, analog monitoring, and multichannel test equipment. The 14-pin SOIC footprint supports conventional surface-mount assembly and is useful when four channels must fit into one package. Common-mode and output-swing headroom should be checked against the actual signal and load because a wide supply rating does not mean the inputs and outputs can reach every supply rail under all conditions. A practical design starts by confirming the automotive-compliant variant requirement, power-supply range, input common-mode range, output swing, load capability, and noise-sensitive signal path. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they remain in a defined state. The SOIC package should be inspected for assembly-layout requirements and the complete operating limits in the manufacturer datasheet. This product overview combines the LM2902AQS14-13 electrical characteristics with package guidance, design considerations, and verified drop-in comparison options. It is intended to help engineers evaluate channel count, supply tolerance, offset performance, bandwidth, and automotive suitability before committing to a PCB design.

RFQ İletişim
LM2902AQT14-13 - 36V Quad Op Amp | Diodes Incorporated
LM2902AQT14-13

LM2902AQT14-13 - 36V Quad Op Amp | Diodes Incorporated

The Diodes Incorporated LM2902AQT14-13 is a four-channel general-purpose operational amplifier designed for automotive and industrial systems operating from a single 3 V to 36 V supply or from dual supplies of ±1.5 V to ±18 V. Each amplifier provides 700 kHz unity-gain bandwidth, 0.3 V/us slew rate, 100 dB large-signal voltage gain, 700 uA typical supply current, and 20 nA typical input bias current. The device is packaged in a 14-pin TSSOP. An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set its gain. A quad op amp combines four amplifiers in one package, allowing designers to implement four independent analog signal-conditioning channels while reducing board area. Within the broader semiconductor hierarchy, the LM2902AQT14-13 belongs to the linear amplifier and analog signal-conditioning IC category. The automotive-qualified LM2902A variant provides a typical input offset voltage of 1 mV, compared with 2 mV for the non-A LM2902 version. Its wide supply range covers 12 V and 24 V automotive rails, while its common-mode input and output capabilities suit sensor buffering, actuator interfaces, and low-frequency control loops. Low input bias current of 20 nA helps preserve accuracy when driving high-impedance sensors. The internal architecture is internally compensated for stable unity-gain operation, allowing each channel to operate as a voltage follower, inverting amplifier, non-inverting amplifier, comparator, or differential input stage. With 700 kHz bandwidth and 0.3 V/us slew rate, the device handles general-purpose analog signals rather than demanding high-speed precision applications. Typical uses include battery-management-system sensor interfaces, automotive body and chassis control, industrial transducers, instrumentation amplifiers, active filters, and 4-to-20 mA current-loop receivers. The 14-TSSOP package also makes the quad amplifier practical for compact control boards where every square millimeter matters. When laying out the PCB, keep input and feedback traces short, place input-biasing resistors close to the non-inverting inputs, and provide stable bypass capacitance at the supply pins. Verify common-mode headroom at the selected output level and confirm the operating temperature rating against the vehicle or industrial environment before release. This page consolidates supply-range, bandwidth, offset, automotive-qualification, pinout, and drop-in replacement information, and adds application-specific design guidance that helps shorten component selection and board-layout decisions.

RFQ İletişim
LM2902AS14-13 - Quad 36V Op Amp | Diodes Incorporated
LM2902AS14-13

LM2902AS14-13 - Quad 36V Op Amp | Diodes Incorporated

Diodes Incorporated LM2902AS14-13 is a standard general-purpose quad operational amplifier with four amplifier circuits, a 3 V to 36 V supply range, 1.3 MHz gain-bandwidth product, 100 dB open-loop gain, and 375 uA typical quiescent current. The device is supplied in a 14-pin surface-mount SO package. An operational amplifier, or op amp, is a high-gain analog signal-conditioning component used to amplify voltage differences, buffer sensors, and drive external circuits. The LM2902 belongs to the quad operational amplifier hierarchy, combining four amplifiers in one package. It is intended for general-purpose industrial and instrumentation applications operating from single or dual supplies. The principal features of the LM2902AS14-13 include a wide 3 V minimum supply, 36 V maximum supply, 1 mV maximum input offset voltage, 1.3 MHz gain-bandwidth product, and 100 dB open-loop gain. Its 375 uA typical quiescent current supports low-power signal processing, while the 14-SO package simplifies assembly on conventional surface-mount PCB layouts. The four amplifier sections provide common functions such as non-inverting and inverting gain, voltage followers, comparators, transducers, and instrumentation interfaces. Because all four sections are integrated in one package, a complete analog signal-conditioning channel can be implemented without using four separate single amplifiers. PCB designers should preserve input/output symmetry and route high-impedance input signals away from switching nodes and supply-current paths. Typical applications include industrial sensor conditioning, transducer amplification, current-loop interfacing, audio preamplification, instrumentation amplifiers, active filters, and general low-frequency signal processing. The 3 V to 36 V operating range permits operation from conventional 5 V, 12 V, and 24 V supply systems, subject to the maximum total supply and input common-mode constraints. When designing a new circuit, check the input common-mode range, output swing, slew rate, and stability requirements at the intended operating frequency. Add supply-bypass capacitors close to the device and avoid placing sensitive input traces beside digital switching paths. The SO-14 footprint requires confirmation against the current PCB footprint before substitution. This product page combines operating limits, application guidance, package information, drop-in comparison options, and practical PCB considerations. It is intended to help engineers evaluate the LM2902AS14-13 for new designs and legacy repairs without treating every similarly rated amplifier as a functional substitute.

RFQ İletişim
LM2902AT14-13 - Quad 1.3MHz Op Amp | Diodes Incorporated
LM2902AT14-13

LM2902AT14-13 - Quad 1.3MHz Op Amp | Diodes Incorporated

Diodes Incorporated LM2902AT14-13 is a general-purpose quad operational amplifier containing four amplifier channels in a 14-pin TSSOP package. The device operates with a 1.3 MHz gain-bandwidth product, offers 100 dB open-loop gain, and draws 375 uA supply current per amplifier. Its four-channel integration makes it suitable for compact analog signal-conditioning boards requiring multiple independently configured amplifier stages. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier used to amplify, filter, buffer, compare, or control analog signals. The LM2902 family belongs to the broader voltage-amplifier and analog-signal-processing hierarchy. It is intended for general-purpose designs rather than precision or high-speed signal chains, making it useful for transducers, sensor interfaces, audio paths, and control systems where economy, low power, and functional integration are priorities. The quad configuration provides four amplifiers in one package, reducing board area compared with four separate single or dual amplifier packages. The 1.3 MHz gain-bandwidth product supports applications requiring moderate rather than very high closed-loop bandwidth. Its 100 dB open-loop gain provides substantial correction capability, while the 375 uA operating current per channel supports low-power analog systems. Operating from a single supply is useful when negative supply rails are unavailable or undesirable. The LM2902 uses a conventional general-purpose amplifier architecture intended for moderate accuracy and broad operating conditions. Because the four channels share one package, their supply, ground, and thermal environments are closely related. Designers should preserve adequate stability around each amplifier, account for input common-mode range and output swing, and avoid relying on rail-to-rail input or output operation. The 1.3 MHz bandwidth also makes stability and noise considerations more important than in precision, low-offset alternatives. Typical uses include four-channel sensor conditioning, low-frequency active filtering, audio preamplification, comparator-style threshold circuits, current-to-voltage conversion, and general industrial control. The package is particularly useful when several low-frequency analog channels must be consolidated on a compact board. Its automotive temperature grade makes it relevant to vehicle electronics, provided each electrical limit is evaluated against the complete operating environment. A primary design consideration is the voltage-loss margin required by a non-rail-to-rail amplifier. Input and output voltage ranges must be checked against the actual supply voltage and signal amplitude. Decoupling should be placed close to the supply pins, the unused amplifier channel should be configured according to the manufacturer's recommendations, and PCB grounding should minimize voltage-drop and feedback coupling between sensitive channels. This product record combines the LM2902AT14-13 specifications with package guidance, application-oriented design notes, and a strict compatibility review. It helps engineers determine whether the quad TSSOP implementation fits a power-conscious analog design before committing to a board layout or production release.

RFQ İletişim
LM2902AWYDT - Quad 1.3MHz Op Amp, 14-SO | STMicroelectronics
LM2902AWYDT

LM2902AWYDT - Quad 1.3MHz Op Amp, 14-SO | STMicroelectronics

The STMicroelectronics LM2902AWYDT is a low-power quad operational amplifier with four internally compensated amplifiers, 1.3 MHz gain-bandwidth performance, and 100 dB typical open-loop gain. It is packaged in a 14-pin small-outline package identified as 14-SO and is intended for general-purpose signal conditioning across automotive and industrial control systems. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The quad configuration integrates four independent amplifiers into one 14-SO package. Internal frequency compensation simplifies closed-loop design, while a common power architecture allows the four amplifiers to operate from a single supply over a wide voltage range. The LM2902 family therefore provides more functional density than discrete single amplifiers and reduces the number of components needed for multi-channel analog circuits. Key electrical characteristics include a 1.3 MHz gain-bandwidth product, 100 dB typical gain, approximately 375 uA supply current per amplifier, 20 nA input bias current, 2 nA input offset current, and 800 V input differential voltage capability. These characteristics support general-purpose applications where low power, usable bandwidth, and moderate input precision are more important than high-speed or precision amplifier performance. The device uses four independent operational amplifiers with internally implemented frequency compensation. Its push-pull output stage supports output-current demands commonly encountered in buffer, comparator-style, and analog-control circuits. The operating approach is suited to single-supply systems, where an amplifier may operate from an input and output signal referenced to the same supply rail rather than requiring a symmetrical positive and negative supply. Typical uses include industrial process-control loops, automotive interface circuits, sensor conditioning, current-to-voltage conversion, low-frequency active filters, and general signal amplification. The four amplifiers can process related channels or provide separate functions such as amplification, filtering, thresholding, and buffering on one PCB. For designs requiring more precision or bandwidth, the device should be compared against the corresponding performance limits before compensation, noise, or offset requirements are finalized. Layout should preserve short feedback paths, maintain suitable grounding, and place input and output decoupling close to the device. Because this is a general-purpose quad amplifier, stability is commonly established with the manufacturer's recommended compensation approach and output isolation resistors where capacitive loading requires them. Verify input and output common-mode limits, supply voltage, load current, and thermal conditions against the manufacturer datasheet before releasing the circuit. This product record combines the LM2902AWYDT device identity, package information, principal electrical characteristics, sourcing context, and verified drop-in alternatives. It also adds practical guidance for comparing the STMicroelectronics LM2902 family with pin-compatible single-supply quad amplifiers from Texas Instruments and NXP Semiconductors.

RFQ İletişim
LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics
LM2902AWYPT

LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics

STMicroelectronics LM2902AWYPT is a low-power, general-purpose quad operational amplifier with four push-pull amplifier channels, a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and a 14-TSSOP package. It is designed for compact analog signal-conditioning systems that require four amplifiers in one package. The manufacturer identifies the device as a low-power quad operational amplifier for instrumentation and general-purpose amplifier applications. An operational amplifier is a high-gain, high-impedance differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The quad LM2902A configuration places four independent amplifiers in one package, reducing component count and board area compared with four separate single or dual amplifier packages. In the broader semiconductor hierarchy, an operational amplifier is an analog IC, a signal-conditioning IC, and part of the wider linear and mixed-signal semiconductor family. Key electrical attributes include a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and 375 µA typical quiescent current. The input bias-current figures listed for this device are 20 nA and 2 nA for different operating conditions, while its stated withstand voltage is 800 V. These characteristics make the LM2902AWYPT suitable for low-frequency instrumentation, sensor interfaces, transducers, and general feedback-control circuits where four amplifier channels can share a common supply architecture. The push-pull output stage supports bidirectional output current without the crossover distortion commonly associated with older single-ended output designs. Each amplifier can implement non-inverting, inverting, summing, difference, comparator-style, or active-filter configurations when operated within its electrical limits. Independent channels allow one package to serve several signal paths, although each channel requires correct feedback and decoupling arrangements to prevent unintended oscillation or channel interaction. Typical uses include low-frequency sensor conditioning, process-control instrumentation, current-voltage conversion, sample-and-hold circuitry, audio preamplification, active filtering, and general-purpose differential amplification. Four channels in one 14-TSSOP package can be especially useful in sensor nodes where several measurements must be conditioned before conversion or control. The package also supports compact mixed-signal boards where conserving board area is more important than very high slew rate or rail-to-rail input and output operation. Designers should begin with the pin-description table and typical application circuits in the STMicroelectronics datasheet. Place the supply bypass capacitor close to the device, keep feedback-loop routing compact, and route each output only to its assigned load. Confirm that input and output common-mode voltages remain within the amplifier's permitted operating range and that source and load impedances preserve stability with the selected feedback network. This product page consolidates the exact manufacturer-listing attributes, package information, commercially available replacement data, and application guidance for LM2902AWYPT. It also distinguishes verified electrical characteristics from parameters that require confirmation in the full manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer documentation conflicts.

RFQ İletişim
LM2902D - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902D

LM2902D - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902D is a general-purpose quad operational amplifier built with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz typical gain-bandwidth product, and 2 mV typical input offset voltage in a 14-pin SOIC package. It supports single-supply or split-supply operation and is designed for instrumentation, buffering, amplification, and general analog signal-chain applications. An operational amplifier is a voltage-gain amplifier that uses negative feedback to control gain, bandwidth, input impedance, and output behavior. The quad LM2902 combines four amplifiers in one integrated circuit, reducing board area compared with four separate single or dual amplifier packages. Its general-purpose architecture belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy and is widely used where inexpensive, robust signal conditioning is more important than precision or high speed. Key characteristics include four independent amplifier channels, push-pull output capability, a 1.2 MHz typical gain-bandwidth product, and 2 mV typical offset voltage. The 26 V maximum supply rating provides compatibility with common industrial voltage ranges. According to the Texas Instruments LM2902 product page, the device is a quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifier. The distributor listing identifies the LM2902D orderable package as 14-SOIC. The internal architecture is frequency compensated and intended to operate from a single supply or split supply over a wide voltage range. Each amplifier can be used independently, while the common package provides four channels for instrumentation, sensor interfaces, active filters, voltage followers, and signal-conditioning blocks. The device should be selected against the complete input/output voltage, common-mode range, output-current, noise, and thermal requirements of the target circuit. Typical applications include industrial measurement, transducer interfaces, audio and control circuits, low-frequency active filters, sensor amplifiers, and general-purpose analog signal conditioning. Because it is a general-purpose amplifier, the LM2902D is most appropriate when system cost, supply tolerance, and availability matter more than very low offset, rail-to-rail operation, or high-frequency precision. The primary design consideration is supply and signal-range verification. Confirm that every input and output remains within the device's specified operating limits under load, temperature, and supply variation. Decoupling capacitors should be placed close to the supply pins, and each amplifier channel requires appropriate feedback and biasing. PCB creepage, grounding, output loading, and decoupling should be checked during layout. This page combines verified manufacturer and distributor information, drop-in replacement guidance, package comparison data, and practical design notes to help engineers evaluate the LM2902D for new designs and service replacements.

RFQ İletişim
LM2902DG - 4-Channel 1 MHz Op Amp | onsemi | SOIC-14
LM2902DG

LM2902DG - 4-Channel 1 MHz Op Amp | onsemi | SOIC-14

onsemi LM2902DG is a single-supply, quad operational amplifier with four amplifiers, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a 3 V to 32 V supply-voltage range in a 14-pin SOIC package. The device uses true differential inputs and provides four independent general-purpose amplifier channels in one compact circuit. An operational amplifier, commonly shortened to op amp, is an analog integrated circuit that amplifies the difference between two input voltages. A quad operational amplifier integrates four amplifiers into one package. Within the device hierarchy, LM2902DG belongs to the operational-amplifier, analog-amplifier, and integrated-circuit categories. Its differential input structure makes it useful for amplifying sensor signals, buffering analog voltages, and implementing general-purpose analog signal-conditioning circuits. Key operating characteristics include a 1 MHz gain-bandwidth product and 0.6 V/µs slew rate. The 3 V minimum supply voltage supports low-voltage analog systems, while operation up to 32 V covers higher-voltage industrial signal chains. Four independent channels reduce package count and simplify board design when multiple analog signals must be amplified, buffered, or filtered. The LM2902 family uses the LM324-series architecture optimized for single-supply operation. True differential inputs allow each amplifier to respond to the voltage difference between its inverting and non-inverting terminals. Because the four channels share one package, designers must consider common supply and ground connections, output-current behavior, stability with capacitive loads, and power dissipation when all channels operate simultaneously. Typical uses include industrial sensor interfaces, low-side current measurement, analog signal conditioning, transducer amplification, general-purpose buffer stages, and four-channel control systems. A single package can implement four similar signal paths, provided each channel remains within its input-voltage, output-swing, current, and stability limits. A key design consideration is the relationship between supply voltage, output swing, and input common-mode range. Confirm that incoming sensor signals remain within the amplifier's permitted input range and that the required output voltage can be reached with the selected load. Place bypass capacitors close to the supply pins and route the common ground connection carefully to minimize offset and noise coupling. This product page combines the exact LM2902DG electrical and package identifiers with engineering-focused selection guidance, drop-in cross-reference information, comparison parameters, and practical PCB design notes. It is intended to help engineers determine package compatibility, verify key operating limits, and select a replacement without overlooking changes in amplifier performance or environmental requirements.

RFQ İletişim
LM2902DG4 - Quad 1.2MHz Op Amp, 26V | Texas Instruments
LM2902DG4

LM2902DG4 - Quad 1.2MHz Op Amp, 26V | Texas Instruments

Texas Instruments LM2902DG4 is a general-purpose quadruple operational amplifier packaged in a 14-pin SOIC tube. Each of its four independent amplifier sections has a gain-bandwidth product of 1.2 MHz and a slew rate of 0.5 V/µs. The device supports single-supply operation up to 26 V and split-supply operation up to ±13 V, with an input offset voltage of 2 mV. Its four-amplifier configuration consolidates multiple analog signal-conditioning channels into one package. A general-purpose operational amplifier is an analog IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902 belongs to the operational-amplifier hierarchy, which includes instrumentation, comparator, voltage-feedback, and current-feedback devices. Four independent sections allow a single LM2902DG4 to implement functions such as sensing, buffering, error amplification, active filtering, and output-current buffering when their common-mode, voltage, and timing requirements overlap. The LM2902's principal characteristics include four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 0.5 V/µs slew rate, and a typical supply-current drain of 0.8 mA. Its input offset voltage is specified as 2 mV, while the operating supply range extends to 26 V on a single supply or ±13 V from a split supply. These characteristics make the device appropriate for general-purpose industrial control, analog signal conditioning, and low-to-moderate-frequency closed-loop applications. The LM2902 is designed around four internally compensated, high-gain operational-amplifier sections. Its 1.2 MHz gain-bandwidth product limits the closed-loop bandwidth achievable at a given noise gain, while the 0.5 V/µs slew rate governs large-signal response. Because all four sections share the same package and supply pins, layout should preserve short feedback paths and provide suitable supply bypassing close to the device. Typical uses include transducer-signal conditioning, low-frequency active filters, industrial sensor interfaces, control-loop error amplifiers, and analog signal buffers. A single package is particularly useful when a board needs several similar amplifier channels and designers want to reduce component count. For applications requiring precision offsets, wider bandwidth, lower noise, rail-to-rail inputs or outputs, or automotive qualification, the design should use a more specialized amplifier rather than assume the LM2902 provides those capabilities. When laying out a board, place the bypass capacitor at the supply pins and route feedback components close to the relevant amplifier section. Check input and output swing against the actual load because the usable signal range depends on the supply voltage and output-load conditions. For stable operation, confirm that the intended noise gain and closed-loop gain are compatible with the 1.2 MHz gain-bandwidth product and that the resulting output slew requirement remains below 0.5 V/µs. This page organizes the LM2902DG4 specifications, pinout, practical design guidance, application examples, and verified drop-in alternatives into one engineering reference. It also separates core device characteristics from procurement details so designers can evaluate the amplifier's package, supply range, bandwidth, and replacement options before committing it to a PCB design.

RFQ İletişim
LM2902DR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM2902DR

LM2902DR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM2902DR is a general-purpose quad operational amplifier built with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz typical gain-bandwidth product, and 2 mV typical input offset voltage in a 14-pin SOIC package. It supports single-supply or split-supply operation and is designed for instrumentation, buffering, amplification, and general analog signal-chain applications. An operational amplifier is a voltage-gain amplifier that uses negative feedback to control gain, bandwidth, input impedance, and output behavior. The quad LM2902 combines four amplifiers in one integrated circuit, reducing board area compared with four separate single or dual amplifier packages. Its general-purpose architecture belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy and is widely used where inexpensive, robust signal conditioning is more important than precision or high speed. Key characteristics include four independent amplifier channels, push-pull output capability, a 1.2 MHz typical gain-bandwidth product, and 2 mV typical offset voltage. The 26 V maximum supply rating provides compatibility with common industrial voltage ranges. According to the Texas Instruments LM2902 product page, the device is a quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifier. The distributor listing identifies the LM2902DR orderable package as 14-SOIC. The internal architecture is frequency compensated and intended to operate from a single supply or split supply over a wide voltage range. Each amplifier can be used independently, while the common package provides four channels for instrumentation, sensor interfaces, active filters, voltage followers, and signal-conditioning blocks. The device should be selected against the complete input/output voltage, common-mode range, output-current, noise, and thermal requirements of the target circuit. Typical applications include industrial measurement, transducer interfaces, audio and control circuits, low-frequency active filters, sensor amplifiers, and general-purpose analog signal conditioning. Because it is a general-purpose amplifier, the LM2902DR is most appropriate when system cost, supply tolerance, and availability matter more than very low offset, rail-to-rail operation, or high-frequency precision. The primary design consideration is supply and signal-range verification. Confirm that every input and output remains within the device's specified operating limits under load, temperature, and supply variation. Decoupling capacitors should be placed close to the supply pins, and each amplifier channel requires appropriate feedback and biasing. PCB creepage, grounding, output loading, and decoupling should be checked during layout. This page combines verified manufacturer and distributor information, drop-in replacement guidance, package comparison data, and practical design notes to help engineers evaluate the LM2902DR for new designs and service replacements.

RFQ İletişim
LM2902DR2 - Quad Single-Supply Op Amp | onsemi | SOIC-14
LM2902DR2

LM2902DR2 - Quad Single-Supply Op Amp | onsemi | SOIC-14

The onsemi LM2902DR2 is a single-supply, quad operational amplifier packaged in a 14-pin SOIC. It integrates four independent amplifiers in the LM2902 family, combining differential inputs, low input offset voltage, and a high gain-bandwidth product for general-purpose analog signal conditioning. The LM2902 family supports supply voltages up to 36 V and can also operate from split supplies when supported by the device operating conditions. Its four-amplifier arrangement reduces package count and simplifies board layout where multiple analog channels are required. An operational amplifier is a high-gain, frequency-compensated analog building block used to amplify differential signals, buffer inputs, compare voltages, and drive feedback-control networks. The LM2902 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, signal-conditioning IC, and power-management semiconductor. Its differential-input architecture requires the two input voltages to be considered together, while its common-mode input range can extend to ground for many single-supply applications. The principal benefits of the LM2902DR2 are its four integrated channels, 36 V supply capability, low input offset voltage, and high gain-bandwidth product. Four independent amplifiers in one 14-pin package simplify designs that require several matched circuit functions, such as sensor conditioning, active filtering, or control-loop sections. The low offset voltage helps reduce output error when the amplifier is used with negative feedback, although the actual error also depends on input bias current, resistor matching, temperature, and common-mode operating conditions. The LM2902DR2 is part of the established LM324-family class of low-cost, single-supply quad operational amplifiers with true differential inputs. Because the device is frequency compensated, designers can create stable closed-loop gain stages without adding external compensation capacitors in typical applications. Its 14-pin SOIC footprint supports conventional surface-mount assembly and is also convenient for prototypes, hobbyist boards, education kits, and repair platforms that use the standard quad-op-amp outline. Typical uses include industrial sensor interfaces, low-frequency audio amplification, active filters, comparator-style signal conditioning, and general instrumentation. The quad organization is particularly useful when a circuit needs two or more gain stages, an amplifier-based filter, or multiple independent analog channels. For power-sensitive systems, the 36 V operating class also allows the device to sit behind higher-voltage supplies when the application and protection requirements permit it. When designing a board around the LM2902DR2, check supply voltage, common-mode range, output swing, input bias current, and the required closed-loop gain at the operating frequency. Place input and feedback components close to the relevant amplifier pins, and keep sensitive input nodes away from switching-current paths. Decouple each supply rail near the device, and confirm that every connected output remains within its valid output-voltage range under worst-case load and temperature conditions. This product page combines the LM2902DR2 technical description, package details, sourcing workflow, application guidance, and verified drop-in alternatives. It also organizes parameter comparisons and practical PCB considerations so engineers can evaluate the device, its replacements, and its role in a complete analog signal chain before releasing a design.

RFQ İletişim
LM2902DR2G - Quad 3-26V Operational Amplifier | onsemi
LM2902DR2G

LM2902DR2G - Quad 3-26V Operational Amplifier | onsemi

The onsemi LM2902DR2G is a quad general-purpose operational amplifier designed for single-supply operation from 3 V to 26 V. The device contains four amplifiers in a 14-pin SOIC package, making it suitable for instrumentation, buffering, signal conditioning, and general analog signal-processing circuits. Its integrated design allows four amplifier channels to be placed in one compact package while supporting common single-supply architectures. A general-purpose operational amplifier is a voltage-amplifying active device that uses differential inputs and feedback to control gain, filtering, buffering, and signal conditioning. The quad LM2902 family combines four amplifiers within one semiconductor package, reducing board area and simplifying designs that require multiple independent analog channels. The LM2902DR2G is associated with the onsemi LM2902 family and is identified by distributor listings as a single-supply quad operational amplifier in a 14-SOIC package. The key device characteristics are the four-amplifier configuration, 3 V to 26 V supply range, 14-SOIC package, and general-purpose single-supply operation. These specifications make the device suitable for industrial control systems, sensor interfaces, low-frequency signal conditioning, audio and communications support circuits, and general instrumentation. Because the LM2902 is a general-purpose amplifier rather than a precision or high-speed part, designers should verify input bias current, output swing, noise, slew rate, and stability requirements against the manufacturer datasheet for the actual operating conditions. In a typical single-supply design, the LM2902 is powered from a positive supply while the signal source and reference point are biased near ground. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased so that they remain in a defined operating state. Feedback-network values determine gain and bandwidth, so resistor and capacitor tolerances directly influence signal accuracy. The device should also be evaluated for output-current capability and thermal rise when driving capacitive loads or operating at elevated temperatures. Common uses include sensor signal conditioning, low-level instrumentation, control-loop input stages, active filtering, waveform conditioning, and general-purpose buffering. The 14-SOIC package provides a familiar footprint for designs using standard through-hole assembly, although the exposed thermal behavior and electrical limits remain important at higher ambient temperatures. The LM2902DR2G is therefore best suited to cost-sensitive, low-to-moderate-frequency analog systems where four channels and single-supply convenience matter more than precision or high bandwidth. This page summarizes the device identity, package, operating range, sourcing information, drop-in alternatives, application guidance, and engineering considerations for engineers evaluating LM2902DR2G. The manufacturer datasheet should be consulted for the complete electrical characteristics, recommended operating conditions, pinout, and application details before final circuit release.

RFQ İletişim
LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRE4

LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRE4 is a quad general-purpose operational amplifier with a 26 V maximum supply, 1.2 MHz gain-bandwidth product, and 2 mV typical input offset voltage, housed in a 14-pin SOIC package. The device contains four independent operational amplifiers designed for a broad range of low-frequency signal-conditioning applications. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier with high input impedance and low output impedance. Its feedback network can configure the device as a voltage amplifier, comparator, buffer, summing amplifier, or active filter. The LM2902 belongs to the operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor hierarchies, making it suitable for common industrial, instrumentation, audio, control, and interface circuits. The LM2902DRE4 provides four amplifier channels in one package, reducing board area and simplifying multi-channel designs. Key characteristics include a typical gain-bandwidth product of 1.2 MHz, 0.5 V/µs slew rate, 0.8 mA typical supply-current drain, and low 2 mV input offset voltage. Its wide operating supply range supports single-supply operation up to 26 V and dual-supply operation up to ±13 V. The architecture supports a broad input common-mode range while maintaining low supply-current consumption independent of supply voltage. These characteristics make the amplifier suitable for battery-powered instrumentation, process-control signals, sensor interfaces, audio preamplification, active filtering, and general-purpose analog systems. Because all four amplifiers operate from common supply pins, board designers can simplify rail distribution and decoupling. Typical applications include four-channel sensor conditioning, low-frequency active filters, audio mixer stages, comparator circuits, industrial control interfaces, and instrumentation amplifiers built from discrete op-amp stages. The 14-pin SOIC package is also practical for through-hole prototype assembly and conventional surface-mount production, while the −40 °C to +125 °C temperature range supports industrial environments. Design carefully around input and output voltage limits, common-mode range, output-current capability, and the load presented by the feedback network. Place supply-bypass capacitors close to the positive and negative supply pins, keep feedback traces short, and verify stability with the actual source and load impedances. The manufacturer datasheet and pin-description table should control PCB and schematic assignments. This page combines the LM2902DRE4 electrical characteristics, package details, drop-in alternatives, comparison parameters, and practical application guidance to support faster component selection and board-level implementation.

RFQ İletişim
LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG3

LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRG3 is a general-purpose quadruple operational amplifier with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage in a 14-pin SOIC package. The LM2902DRG3 suffix denotes a tape-and-reel shipping configuration. An operational amplifier, or op amp, is a high-gain analog signal-processing component used to amplify voltage differences, buffer sensors, drive analog inputs, and implement feedback-control circuits. The LM2902 belongs to the quad operational-amplifier family within the broader voltage-amplifier and analog-signal-processing semiconductor hierarchy. Its four amplifiers share power-supply pins but have independent input and output connections, allowing one package to implement four related analog functions. The LM2902 operates from single or split supplies over a wide voltage range, making it useful in industrial-control, instrumentation, and audio circuits. Key characteristics include a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and approximately 0.8 mA typical supply-current drain. Four frequency-compensated amplifiers support common closed-loop configurations including noninverting and inverting gain, voltage followers, comparators, summing amplifiers, and difference stages. Its 14-pin SOIC package provides a familiar industrial footprint and thermal performance suitable for conventional through-hole assembly workflows. Because each channel is independent, the IC can implement sensor conditioning, signal amplification, active filtering, and control-loop functions on one board. Single-supply operation simplifies designs where the signal remains above ground, while split-supply operation supports bipolar signals centered around zero volts. Typical applications include industrial sensor interfaces, transducers, audio preamplifiers, analog-to-digital converter input conditioning, motor-control support circuits, and general-purpose instrumentation. The wide supply range and low supply-current drain make the device practical in equipment powered from industrial rails or split supplies, provided the absolute maximum operating limits remain respected. Designers should verify input and output common-mode limits for each supply configuration, account for the offset voltage when precision is important, and use stable feedback networks for unity-gain or noise-sensitive applications. PCB placement should keep sensitive input nodes compact, provide an appropriate ground-return path, and avoid placing high-current switching paths close to amplifier inputs. This product page combines the LM2902 family specifications, package information, sourcing guidance, verified drop-in candidates, application examples, and practical design considerations. The comparisons also distinguish package-compatible alternatives from choices that require different qualification, temperature-range, or performance checks before substitution.

RFQ İletişim
LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG4

LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902DRG4 is a four-channel operational amplifier with a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input-offset specification in a 14-pin SOIC package. Designed for general-purpose signal conditioning, each amplifier can operate from single or dual supplies, supporting a broad range of industrial, instrumentation, control, and analog-interface applications. An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The LM2902 belongs to the operational-amplifier hierarchy, where it combines transistor-level input and output stages with internal compensation. Each of its four channels can perform amplification, buffering, comparison, summation, differential sensing, or active-filter functions without requiring a separate amplifier for every signal path. The device provides a 1.2 MHz gain-bandwidth product and a 2 mV input-offset specification, making it suitable for moderate-bandwidth precision applications. The 26 V supply capability also supports higher-voltage industrial interfaces than low-voltage rail-to-rail amplifiers. Texas Instruments specifies an operating temperature range from -40°C to 125°C, allowing operation across demanding commercial and industrial environments. The four amplifiers share one package while retaining independent input and output pins, allowing one IC to implement several analog functions. Their typical design role is to operate with feedback networks that establish closed-loop gain and filtering. Because the device is not rail-to-rail by specification, input and output common-mode limits must be checked against the selected supply voltage and signal range before layout release. Typical uses include transducer signal conditioning, low-frequency active filters, sensor amplifiers, industrial control loops, comparator-style threshold circuits, and audio or communications interface stages. The SOIC package also simplifies inspection and rework on through-hole industrial boards while providing a familiar 14-pin land pattern. For a new design, verify the input and output common-mode range, output-current capability, load impedance, and supply operating limits at the intended signal amplitude. Stable feedback and proper decoupling remain important even when the application is a unity-gain buffer, so use the manufacturer pin-description table when assigning PCB tracks. This page organizes the LM2902DRG4 specifications, verified manufacturer references, same-package alternatives, application guidance, and comparison points. It also highlights the practical checks needed to determine whether a candidate replacement is truly pin-compatible rather than merely functionally similar.

RFQ İletişim
LM2902DT - Quad Op-Amp, 3-30V, SOIC-14 | STMicroelectronics
LM2902DT

LM2902DT - Quad Op-Amp, 3-30V, SOIC-14 | STMicroelectronics

The STMicroelectronics LM2902DT is a low-power quad operational amplifier with four independent, high-gain, internally frequency-compensated amplifier stages, a 1.3 MHz gain-bandwidth, 0.4 V/us slew rate, and a wide 3 V to 30 V single-supply operating range, housed in a 14-pin SOIC package. An operational amplifier (op-amp) is an analog building block within the broader amplifier IC and linear IC families that amplifies the voltage difference between its two inputs. Quad op-amps integrate four of these stages in one package, letting a single IC handle multi-channel signal conditioning - sensor buffers, comparators-with-hysteresis, active filters, and summing stages - while sharing one supply rail and saving board area versus four single amplifiers. Key features of the LM2902DT include single-supply operation from 3 V to 30 V (or dual supplies from +/-1.5 V to +/-15 V), an input common-mode range that extends to the negative rail, a 2 mV maximum input offset voltage, and approximately 20 nA input bias current - tighter than the classic LM324 (7 mV offset, 45 nA bias) - which improves accuracy in high-impedance sensor circuits. The bipolar process keeps quiescent current low, and output stages are push-pull with a classic footprint-compatible pinout shared industry-wide. Per STMicroelectronics, the LM2902 family was designed specifically for automotive and industrial control systems; the D suffix denotes the 14-SOIC surface-mount package rated across the automotive temperature span. Internal frequency compensation means no external compensation components are needed at unity gain, simplifying design-in. Typical applications include automotive sensor interfaces, industrial control loops, transducer amplifiers, active filters, and multi-channel DC signal conditioning in 12 V/24 V systems where the supply range and negative-rail input sensing fit naturally. Design consideration: although the inputs sense down to the negative rail, the output cannot swing fully to the rail - allow roughly 1.5 V of headroom on VCC, or use a rail-to-rail output amplifier for low-side signal chains. This page adds value beyond the datasheet by consolidating drop-in alternatives, application guidance, and comparison data for the LM2902DT in one place.

RFQ İletişim
LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi
LM2902DTB

LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi

The onsemi LM2902DTB is a general-purpose quad operational amplifier packaged in a 14-pin TSSOP. It supports a 3 V to 26 V supply range and integrates four amplifier channels, allowing one compact device to implement four independent analog signal-conditioning paths. The LM2902 family is designed for low-cost single-supply equipment where true differential inputs and common-mode operation are useful. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The quad configuration belongs to the hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. True differential inputs allow the amplifier to respond to two input signals rather than requiring both signals to be referenced to ground, making the device useful in sensor, transducer, and feedback networks. The LM2902 family combines a 3 V to 26 V supply range with low quiescent-current operation and a 1.2 MHz unity-gain bandwidth. Its input offset voltage is specified at 2 mV, while the four-channel architecture reduces the number of packages and board-area requirements compared with four separate single amplifiers. These characteristics suit general-purpose analog designs where cost, supply flexibility, and practical integration matter more than precision or rail-to-rail performance. Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or feedback element in a control loop. The device does not reach the positive or negative supply rail at its output, so analog output ranges must be checked against the selected supply voltage and load. Input common-mode range, output swing, input bias current, and noise remain important constraints when precision or high-impedance source designs are required. Typical uses include industrial sensor interfaces, low-cost instrumentation, audio preamplifier stages, active filtering, relay-driver signal conditioning, and general-purpose control boards. A four-channel implementation is especially attractive when several sensors require similar conditioning or when a system needs independent amplifier channels for measurement, monitoring, and feedback. PCB implementation should follow the manufacturer pinout and recommended decoupling guidance. Place the supply bypass capacitor close to the power pins, route sensitive input and feedback traces away from switching nodes, and use a common ground plane with short return paths. Because the outputs cannot swing fully to either rail, applications needing rail-to-rail operation require a different amplifier family. This page combines the LM2902DTB package and supply information with engineering-focused application guidance, replacement criteria, and a parameter comparison. These details help engineers determine when the quad topology simplifies a design and where a single, rail-to-rail, or higher-precision amplifier is the better choice.

RFQ İletişim
LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi
LM2902DTBG

LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi

The onsemi LM2902DTBG is a single-supply quad operational amplifier with four amplifiers, a 3 V to 26 V operating supply range, and a 14-pin TSSOP package. It supports true differential inputs and operation from -40 °C to +105 °C, making it suitable for general-purpose industrial signal-conditioning and control circuits. An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output to amplify the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Its differential input architecture supports common signal-conditioning uses such as buffers, amplifiers, comparators, instrumentation stages, and active-feedback circuits. The principal benefits of the LM2902DTBG are its four independent amplifier channels, single-supply operation from 3 V to 26 V, and low-power design characteristics. Four channels in one package can reduce board area in designs that need several matched general-purpose amplifiers. The broad 3 V to 26 V supply range also permits operation from conventional 5 V and 12 V rails as well as higher industrial supply levels that remain below the device rating. The device is based on the established LM324-family architecture, which uses true differential inputs. According to onsemi documentation, the LM324 series is designed for low-cost, general-purpose applications and provides particular advantages in single-supply systems. A unity-gain bandwidth of approximately 1 MHz is suitable for audio-frequency, sensor-interface, feedback-control, and general analog-signal applications rather than high-speed precision instrumentation. Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, comparator functions, industrial control loops, and general-purpose buffering. The four amplifiers can operate independently, although common power rails and package-level thermal behavior should be considered when all channels drive substantial loads. For new layouts, use the manufacturer pin-description table when assigning PCB tracks and preserve the TSSOP-14 land pattern. Check input common-mode range, output swing, input bias current, noise, offset voltage, and slew rate against the actual signal amplitude and frequency before finalizing the circuit. This page combines the LM2902DTBG operating limits, package information, replacement options, and practical circuit-placement guidance into an engineering-focused selection resource for buyers and designers evaluating quad single-supply op amps.

RFQ İletişim