Ürünler (46.000+)

LM2876TF - 40W Mono Class AB Amplifier | Texas Instruments
LM2876TF

LM2876TF - 40W Mono Class AB Amplifier | Texas Instruments

Texas Instruments LM2876TF is a high-performance 40 W mono Class AB audio power amplifier with mute, specified to deliver continuous average output power into an 8 ohm load from a 20 V to 60 V supply. The device is packaged in an 11-pin TO-220 isolated package. Its stated audio performance includes 0.1% total harmonic distortion plus noise from 20 Hz to 20 kHz under the manufacturer’s stated test conditions. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a loudspeaker, subwoofer, or other high-impedance acoustic load. The LM2876 belongs to the amplifier IC hierarchy, where Class AB describes the output-stage operating method: the amplifier conducts during both halves of the audio waveform while minimizing crossover distortion. It also provides SPiKe protection, described by Texas Instruments as dynamically protecting the device against instantaneous thermal peaks. The principal specifications are 40 W continuous average output power, operation from 20 V to 60 V, and compatibility with an 8 ohm load. The LM2876 is a mono design intended for single-channel audio amplification. Its 0.1% THD+N rating covers 20 Hz to 20 kHz, providing a defined distortion and bandwidth reference when comparing it with other high-power audio amplifiers. Internally, the LM2876 combines Class AB output operation with a mute function and SPiKe thermal protection. The protection system is intended to react to instantaneous power events more effectively than a basic thermal shutdown alone. The isolated TO-220-11 construction supports conventional through-hole assembly and provides a mechanically robust option for audio equipment where heatsinking and grounding layout are important. Typical uses include monoblock subwoofer amplifiers, powered speaker systems, hi-fi amplifier output stages, home-theater audio power amplifiers, and industrial audio drivers. In each case, the amplifier requires a stable high-voltage supply, appropriate output filtering for the selected load, adequate copper area and thermal management, and careful separation of input, output, and power-ground paths. Design should begin with the 40 W continuous-power target rather than the absolute device rating. A practical implementation must provide enough supply headroom, verify thermal conditions at the selected load impedance, and account for the difference between continuous music power and short-duration peaks. The mute and SPiKe features add control and protection functions, but successful operation still depends on correct board layout and thermal design. This page combines the manufacturer’s core LM2876 specifications with purchasing guidance, application-focused engineering guidance, and a packaging-aware replacement assessment. It is intended to help designers determine whether the LM2876TF suits a high-power mono audio stage and how to verify board-level thermal, electrical, and sourcing requirements before committing to a design.

RFQ İletişim
LM2893M - 4.8 kBaud FSK Power-Line Transceiver | Texas Instruments
LM2893M

LM2893M - 4.8 kBaud FSK Power-Line Transceiver | Texas Instruments

The Texas Instruments LM2893M is a carrier-current transceiver integrated circuit for half-duplex serial data communication over existing power lines. It combines an FSK transmitter, a receiver with phase-locked-loop demodulation, and an interface to the carrier-current network in a 20-terminal SOP package. The verified device supports data rates up to 4.8 kBaud and an operating temperature range of -40°C to +85°C. A carrier-current transceiver is a communications interface that superimposes a modulated signal onto an electrical power or communication line. In the broader electronics hierarchy, this device belongs to the interface-IC category rather than a general-purpose data converter. The LM2893M is designed to communicate short serial messages between remotely distributed nodes without requiring a dedicated signal pair, making it useful for energy-management equipment, home-automation controllers, appliance control, and industrial systems that already share a mains-powered network. The principal verified features include FSK modulation, phase-locked-loop demodulation, half-duplex bidirectional operation, a maximum data rate of 4.8 kBaud, operation from an 18 V supply, and a -40°C to +85°C industrial temperature range. Its 20-terminal gull-wing SOP package has a 1.27 mm terminal pitch according to the verified distributor listing. Because carrier-current communication is sensitive to network loading, coupling method, attenuation, noise, and grounding, successful implementation requires the interface network and filtering to be evaluated with the intended power-line environment. The LM2893M is most appropriate when both ends of a link can share a power or utility line and low data throughput is sufficient. The 4.8 kBaud rate suits status reporting, control commands, meter-reading messages, and energy-management telemetry rather than streaming data. Half-duplex operation requires the controller to avoid simultaneous transmission and to manage turnaround timing, while the PLL-based receiver provides the demodulation function required to recover FSK information from the carrier waveform. Designers should provide suitable supply bypassing and define the line-coupling, protection, filtering, and grounding arrangement with the actual mains network. Regulatory, safety, and isolation requirements must be handled by the complete interface circuit rather than assumed to be satisfied by the IC. The LM2893M itself is not a mains-isolated network interface, and its operating voltage should not be confused with the voltage appearing on the coupled power line. This page combines verified pricing, package information, operating limits, interface characteristics, and application guidance with the available manufacturer-family relationship. It also documents the absence of verified drop-in equivalents instead of presenting unverified substitutes as production-ready replacements.

RFQ İletişim
LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments
LM2893MX

LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments

The Texas Instruments LM2893MX is a carrier-current transceiver designed for half-duplex, bidirectional serial communication over power-line or carrier-current networks. The device operates from a nominal 18 V supply, supports 13 V to 24 V and 14 V to 30 V operating ranges, and draws up to 79 mA. It is packaged in a 20-pin SOIC with a 1.27 mm terminal pitch, gull-wing leads, and an industrial temperature range of -40°C to +85°C. A carrier-current transceiver is an interface circuit that couples serial data onto and receives data from an electrical distribution or communication line. Carrier-current systems use an existing power or telephone conductor as the physical transmission medium, allowing equipment located at separate points to exchange information without a dedicated data cable. This places the LM2893MX within the broader hierarchy of communication interface IC, transceiver, line-interface circuit, and semiconductor. The LM2893MX is identified as a telecom interface transceiver and a general-purpose carrier-current interface. Its half-duplex operation supports two-way communication over the same line path, while the 79 mA maximum supply current provides a defined operating limit for power-supply design. The SOIC-20 package supports conventional surface-mount assembly and is suitable for equipment operating across the full -40°C to +85°C industrial temperature range. Carrier-current interfaces depend on accurate line coupling, controlled transmitter behavior, and receiver discrimination between wanted signals and line noise. The LM2893MX integrates the functional interface required for bidirectional serial bit-stream communication at the physical layer. System designers still need to account for line impedance, coupling components, termination, filtering, grounding, and protection networks when constructing a production interface. Typical applications include power-line data links, industrial equipment monitoring, remote telemetry, building automation, carrier-based communication equipment, and telecommunication networks that use existing conductors as communication media. The operating voltage and industrial temperature range make the device relevant to sustained industrial deployments where the interface must tolerate temperature variation and operate from a nominal 18 V supply. Design the LM2893MX around the electrical characteristics of the carrier line rather than treating it as a conventional point-to-point logic interface. External components must be selected for the line voltage, impedance, baud rate, isolation requirements, and transient environment, while the PCB layout should minimize noise coupling between the transmit and receive paths. Confirm the exact pin functions and recommended application circuit in the Texas Instruments datasheet before finalizing a new layout. This product page combines the LM2893MX electrical, package, environmental, and application information with practical PCB and implementation guidance. It also distinguishes the verified device characteristics from parameters that must be confirmed during design-in, helping engineers evaluate the part efficiently while retaining control over circuit-level requirements.

RFQ İletişim
LM2893N - Carrier-Current Transceiver | National Semiconductor
LM2893N

LM2893N - Carrier-Current Transceiver | National Semiconductor

National Semiconductor LM2893N is a one-transceiver carrier-current interface IC designed for half-duplex, bidirectional serial communication over an existing power-mains network. The device is offered in a 20-pin PDIP package and combines a transmitter and receiver in one integrated circuit. Carrier-current systems use power-line infrastructure to transfer information between remotely separated locations rather than requiring a separate communication cable. A carrier-current transceiver is a type of power-line interface IC. Carrier-current communication belongs to the broader power-line networking and interface IC hierarchy, where communication signals are superimposed on an electrical power conductor. The LM2893N is intended to interface a serial data source with a carrier-current network, making it useful where the mains wiring already extends between remote nodes and adding a separate low-speed communication route would be impractical. The verified source information identifies the LM2893N as a one-transceiver, 20-PDIP device for carrier-current systems. Its principal benefit is integration: both directions of the half-duplex link are handled by a single package instead of separate transmitter and receiver packages. The confirmed communication mode is bidirectional and serial, allowing a node to exchange bit-stream data with another node over the same carrier-current medium. The LM2893N belongs to the bipolar LM1893/LM2893 carrier-current transceiver family. This family positioning indicates that the LM2893 is the higher-temperature-oriented member relative to the LM1893 designation, although exact electrical limits and comparison values are not included in the supplied distributor data. Designers should use the manufacturer datasheet for voltage ratings, current limits, logic thresholds, transmission timing, receiver sensitivity, and network-interface details before releasing production hardware. Typical carrier-current uses include remote metering, building-management communication, industrial monitoring, appliance control, and low-speed supervisory links where power and data share the same wiring. In these systems, the LM2893N acts as the physical-layer interface between the communication network and the node's serial logic. Network loading, isolation requirements, coupling method, transmit power, and protocol timing remain application-specific. The principal design consideration is that carrier-current communication is materially different from ordinary RS-485 or isolated digital communication. The power conductor presents a difficult noise environment, and the interface network must be characterized for attenuation, impedance, coupling, and surge exposure. PCB grounding, filtering, isolation boundaries, and protection components therefore deserve attention before the communication protocol is finalized. This product page combines verified distributor identification, family-level technical context, package information, sourcing links, and structured engineering guidance that is not available in a basic distributor listing. Exact electrical specifications and qualified drop-in replacements remain explicitly separated from verified facts so engineers can make a safe replacement decision without relying on assumptions.

RFQ İletişim
LM2900D - Quad Norton Operational Amplifier | Texas Instruments
LM2900D

LM2900D - Quad Norton Operational Amplifier | Texas Instruments

The Texas Instruments LM2900D is a quad, high-gain, frequency-compensated Norton operational amplifier in a 14-pin SOIC (D) package. The device contains four independent amplifier sections designed for single-supply or split-supply operation over a wide supply-voltage range. Its Norton input stage provides low input bias current, while the internally compensated architecture simplifies gain-stage implementation in general-purpose signal conditioning. The LM2900D is identified by the verified distributor listing as a standard general-purpose amplifier with four circuits in a 14-SOIC package. A Norton operational amplifier is a current-buffer input operational-amplifier architecture. It differs from the more common voltage-input differential pair by using a translinear input stage that offers low input bias current and good performance with high-impedance sources. This places the LM2900D in the operational-amplifier hierarchy: operational amplifier, amplifier IC, analog IC, and semiconductor. The part is intended for general-purpose analog signal conditioning rather than precision instrumentation or automotive-qualified systems. According to the Texas Instruments LM2900 product page, the LM2900 family consists of four independent, high-gain frequency-compensated Norton operational amplifiers designed to operate from a single supply over a wide range of voltages. The product description also identifies large output-voltage swing, output short-circuit protection, internal frequency compensation, and low input bias current as important characteristics. These features make the device suitable for buffering, voltage amplification, signal conditioning, and general feedback-control circuits. The LM2900D can be used with a single positive supply or with split supplies. In single-supply designs, the input and output signal levels must remain within the amplifier's common-mode and output-swing limits. The LM2900 family is internally frequency compensated, so the feedback network establishes the closed-loop gain without requiring a separate compensation capacitor in ordinary applications. The 14-pin SOIC package provides a conventional surface-mount footprint and a practical temperature range for industrial and consumer equipment. Typical uses include transducer-signal conditioning, sensor interfaces, audio preamplification, low-current feedback amplifiers, and general analog control loops. Because the verified data does not provide detailed electrical limits, bandwidth, noise, slew rate, or exact input/output range, those parameters should be confirmed in the manufacturer datasheet before final design release. The verified distributor listings show current purchasing channels, but they do not provide a reliable standardized price table in the supplied data. This page combines the verified manufacturer and distributor identity for LM2900D with package information, sourcing links, comparison structure, and practical selection guidance. It is intended to help engineers identify the correct 14-SOIC Norton amplifier while avoiding unsupported parameter assumptions. Confirm the latest ordering information, electrical limits, lead time, and lifecycle status with Texas Instruments or an authorized distributor before production commitment.

RFQ İletişim
LM2900DR - Quad Norton Operational Amplifier | Texas Instruments (Tape & Reel)
LM2900DR

LM2900DR - Quad Norton Operational Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments LM2900DR is a quad, high-gain, frequency-compensated Norton operational amplifier in a 14-pin SOIC (D) package. The device contains four independent amplifier sections designed for single-supply or split-supply operation over a wide supply-voltage range. Its Norton input stage provides low input bias current, while the internally compensated architecture simplifies gain-stage implementation in general-purpose signal conditioning. The LM2900DR is identified by the verified distributor listing as a standard general-purpose amplifier with four circuits in a 14-SOIC package. A Norton operational amplifier is a current-buffer input operational-amplifier architecture. It differs from the more common voltage-input differential pair by using a translinear input stage that offers low input bias current and good performance with high-impedance sources. This places the LM2900DR in the operational-amplifier hierarchy: operational amplifier, amplifier IC, analog IC, and semiconductor. The part is intended for general-purpose analog signal conditioning rather than precision instrumentation or automotive-qualified systems. According to the Texas Instruments LM2900 product page, the LM2900 family consists of four independent, high-gain frequency-compensated Norton operational amplifiers designed to operate from a single supply over a wide range of voltages. The product description also identifies large output-voltage swing, output short-circuit protection, internal frequency compensation, and low input bias current as important characteristics. These features make the device suitable for buffering, voltage amplification, signal conditioning, and general feedback-control circuits. The LM2900DR can be used with a single positive supply or with split supplies. In single-supply designs, the input and output signal levels must remain within the amplifier's common-mode and output-swing limits. The LM2900 family is internally frequency compensated, so the feedback network establishes the closed-loop gain without requiring a separate compensation capacitor in ordinary applications. The 14-pin SOIC package provides a conventional surface-mount footprint and a practical temperature range for industrial and consumer equipment. Typical uses include transducer-signal conditioning, sensor interfaces, audio preamplification, low-current feedback amplifiers, and general analog control loops. Because the verified data does not provide detailed electrical limits, bandwidth, noise, slew rate, or exact input/output range, those parameters should be confirmed in the manufacturer datasheet before final design release. The verified distributor listings show current purchasing channels, but they do not provide a reliable standardized price table in the supplied data. This page combines the verified manufacturer and distributor identity for LM2900DR with package information, sourcing links, comparison structure, and practical selection guidance. It is intended to help engineers identify the correct 14-SOIC Norton amplifier while avoiding unsupported parameter assumptions. Confirm the latest ordering information, electrical limits, lead time, and lifecycle status with Texas Instruments or an authorized distributor before production commitment.

RFQ İletişim
LM2900N - Quad 2.5MHz Norton Operational Amplifier | TI
LM2900N

LM2900N - Quad 2.5MHz Norton Operational Amplifier | TI

The Texas Instruments LM2900N is a quad, high-gain, frequency-compensated Norton operational amplifier with four independent amplifiers in a 14-pin PDIP package. Its headline specifications include a 2.5 MHz gain-bandwidth product, 20 V/µs slew rate, 4.5 V to 32 V single-supply operation, and ±2.2 V to ±16 V dual-supply operation. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2900 belongs to the Norton-operational-amplifier family, characterized by current-feedback-style input stages. Within the broader electronics hierarchy, it is an analog amplifier IC, then an operational amplifier, then a general-purpose quad amplifier. The LM2900 provides four independent amplifiers, wide bandwidth, large output-voltage swing, short-circuit protection, internal frequency compensation, and low input-bias current. Internal compensation removes the need for external compensation components in ordinary closed-loop operation, simplifying analog boards that need several amplified signals on one supply rail. Its specified 4.5 V to 32 V single-supply range makes it applicable to legacy industrial control, instrumentation, sensor interfaces, audio, and communications equipment. The 20 V/µs slew rate supports faster edge rates than many general-purpose amplifier selections, while the 2.5 MHz bandwidth gives useful signal bandwidth for audio and control applications. The DIP package also supports through-hole assembly and socketed prototypes. When designing around the LM2900N, verify input and output common-mode limits at the selected supply voltage. Account for the input-bias current when driving high-impedance sensors, and use stable feedback networks with resistive isolation where required by the source impedance. The device uses four independent amplifiers, but shared-package power and ground connections still require careful layout. This product record combines the verified Texas Instruments family description, distributor package information, ordering details, and cross-reference findings. It also distinguishes electrically similar ordering variants from verified pin-compatible replacements and identifies application guidance that is not presented as a manufacturer reference design.

RFQ İletişim
LM2900NE4 - Quad Norton Op Amp, 2.5 MHz | Texas Instruments
LM2900NE4

LM2900NE4 - Quad Norton Op Amp, 2.5 MHz | Texas Instruments

The Texas Instruments LM2900NE4 is a quad, high-gain, frequency-compensated Norton operational amplifier packaged in a 14-pin PDIP. It contains four independent amplifier sections in one package and is designed for general-purpose analog signal conditioning. The device operates from single or split supplies and supports a wide range of supply voltages, with a listed operating range up to 15 V. Its 2.5 MHz gain-bandwidth product and 20 V/µs slew rate provide useful bandwidth for low-frequency instrumentation, signal conditioning, filtering, and general analog processing. The LM2900NE4 uses the Norton current-feedback operational-amplifier architecture. Unlike a conventional voltage-feedback amplifier, the Norton topology is based on low-input-resistance current feedback and is well suited to applications where the source impedance and feedback network are compatible with that operating principle. Internal frequency compensation makes the amplifier convenient to use without external compensation components in closed-loop gain configurations specified by the manufacturer. Key specifications include four amplifier circuits, a 2.5 MHz gain-bandwidth product, a 20 V/µs slew rate, and a 14-pin PDIP package. The device also provides wide supply-voltage operation, large output-voltage swing, output short-circuit protection, and low input-bias-current characteristics according to the LM2900 family information. These features make the LM2900NE4 suitable for industrial control, sensor interfaces, audio and communication signal paths, and test equipment. The quad package can reduce board area when four similar analog functions are required. Each amplifier is independent, allowing the same device to implement four separate gain, buffering, comparison, or filtering functions. The PDIP format is also convenient for through-hole assembly, prototyping, repair, and applications where a large thermal pad is not required. When designing around the LM2900NE4, verify the source impedance and feedback values against the manufacturer’s recommended operating conditions. Because the Norton architecture has different input and feedback considerations from a voltage-feedback op amp, do not substitute a conventional amplifier without checking stability, slew behavior, output swing, and bias-current requirements. Maintain adequate supply decoupling and observe the specified common-mode and output-voltage limits. This product page combines the manufacturer family information, distributor package and availability references, technical comparisons, and practical design guidance to support component selection and replacement planning for the LM2900NE4.

RFQ İletişim
LM2900NG4 Quad Norton Op Amp | 14-PDIP | Texas Instruments
LM2900NG4

LM2900NG4 Quad Norton Op Amp | 14-PDIP | Texas Instruments

Texas Instruments LM2900NG4 is a quad, high-gain, frequency-compensated Norton operational amplifier integrated circuit in a 14-pin PDIP package. It contains four independent amplifier sections designed for general-purpose signal amplification, buffering, instrumentation, and other linear analog applications. The device is identified as a standard general-purpose amplifier with a DIP-14 package and is suitable for single-supply operation across a wide voltage range, with split-supply operation also possible. A Norton operational amplifier is a current-buffer amplifier architecture rather than a conventional voltage-input amplifier. Its input signal is represented as a current, which allows the amplifier to operate with relatively low input bias current and can be useful in sensor interfaces, current-feedback signal paths, and feedback networks. The LM2900 family combines four amplifiers in one package, reducing board area and simplifying multi-channel analog designs where several similar signal-processing stages are required. The principal application features are its quad amplifier organization, high gain, internal frequency compensation, and single-supply capability. Frequency compensation allows each amplifier to be used as a stable gain stage without requiring an external compensation network in many standard closed-loop configurations. The wide operating supply range supports industrial, instrumentation, audio, control, and embedded analog systems where the supply voltage is not tightly constrained. The LM2900NG4 uses a 14-pin PDIP package with through-hole mounting. Through-hole construction is useful for prototypes, educational platforms, legacy control boards, industrial equipment, and repair applications where a socket or conventional PCB drilling process is preferred. The DIP-14 footprint also provides generous spacing between leads, simplifying hand assembly and inspection compared with fine-pitch surface-mount packages. When designing around the LM2900NG4, identify the function of each amplifier section and confirm the complete pin assignment, supply requirements, input and output common-mode limits, output swing, and stability behavior in the manufacturer datasheet. Use the manufacturer datasheet for the exact pinout and application examples. Feedback resistors and compensation choices should be calculated for the intended closed-loop gain, while input and output signal paths should be kept short to reduce noise pickup and instability risk. This product page organizes the LM2900NG4 technical profile, sourcing information, package details, practical design notes, and a comparison framework for engineers evaluating quad general-purpose op amps. It is intended to support component selection, schematic review, PCB compatibility checks, and replacement planning rather than replace the complete manufacturer datasheet.

RFQ İletişim
LM2901D - 30V Quad Differential Comparator | Texas Instruments
LM2901D

LM2901D - 30V Quad Differential Comparator | Texas Instruments

The Texas Instruments LM2901D is a 30 V quad differential comparator containing four independent open-collector comparator channels in a 14-pin SOIC package. Each channel supports single or split-supply operation, while the device is designed for level detection, low-level sensing, memory, consumer, automotive, and industrial applications. The LM2901D combines a typical input bias current of 25 nA with a typical input offset current of ±5 nA. A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level result indicating which input is higher. Within the semiconductor hierarchy, the LM2901D is a voltage comparator, a linear signal-conditioning IC commonly grouped with amplifier and interface functions. Its open-collector outputs require an external pull-up resistor, allowing several outputs to be wired together when the resulting wired-AND behavior is appropriate for the system. The four independent channels make the LM2901D useful where several sensing decisions must be made in one package. Its open-collector output structure can drive TTL, CMOS, MOS, DTL, and ECL-compatible logic as identified in the manufacturer literature. The specified 300 ns response time supports general-purpose detection rather than the latency demanded by high-speed timing applications. Split-supply operation also permits bipolar sensing around a zero-volt reference. The input stage emphasizes low bias current, which reduces disturbance of high-impedance sensor outputs. A typical 25 nA input bias current is suitable for many threshold and level-detection circuits, while the typical ±5 nA input offset current helps minimize imbalance between the differential inputs. These characteristics should be considered together with input common-mode limits, output pull-up requirements, and supply-voltage tolerances during design verification. Typical uses include monitoring battery or power rails, detecting overvoltage and undervoltage conditions, comparing sensor thresholds, implementing window comparators, and providing four-channel status indication. Because all four outputs are open collector, a pull-up resistor is normally required on each channel. Connecting multiple open-collector outputs to one pull-up can reduce the number of logic signals, but it also creates a shared fault domain and requires careful analysis of output leakage and pull-up current. A practical design must preserve adequate input common-mode headroom at both supply rails, keep differential input voltage within the absolute maximum limits, and select pull-up resistors for the voltage and sink-current requirements of the connected logic. Decoupling capacitors should be placed close to the supply pins, while unused comparator inputs should be tied to a defined potential rather than left floating. This page organizes the key LM2901D electrical characteristics, manufacturer-backed comparison options, pin-package constraints, and application guidance for engineers evaluating a 14-pin quad comparator. It also highlights the practical trade-offs involved when selecting a drop-in alternative with different input offset, bias current, temperature range, or propagation timing.

RFQ İletişim
LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments
LM2901DE4

LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments

The Texas Instruments LM2901DE4 is a quad differential comparator with open-collector outputs, designed for single-supply operation from 2 V to 30 V or split-supply operation within the stated common-mode limits. The device contains four independent comparator channels in a 14-pin SOIC package, with a typical input offset voltage of 0.37 mV and an input bias current of 3.5 nA. Each channel can compare two input voltages and provide a logic-level indication through an open-collector output. The LM2901DE4 is suitable for industrial control, sensor interfacing, threshold detection, voltage monitoring, and general-purpose signal conditioning applications. Its low supply current of approximately 200 uA per comparator and wide operating temperature range of -40 °C to +125 °C make it practical for both commercial and extended-temperature equipment. The open-collector outputs allow wired-AND operation and require an external pull-up resistor when the output must drive a logic high. A differential comparator is an analog integrated circuit that compares two voltage inputs and changes its output state according to their relative voltage. The LM2901 belongs to the comparator category within the broader interface IC hierarchy, where analog front-end decision-making is followed by digital logic, control, or measurement. Unlike an operational amplifier, the comparator is intended primarily for threshold crossing and does not provide linear amplification. The LM2901 family combines four channels in one package, allowing a compact design when multiple independent decisions are needed. Its common-mode input range includes ground, making it useful in systems powered from a single positive rail where the signal being compared can approach 0 V. Key features include a maximum supply rating of 38 V, a low input offset voltage of 0.37 mV, an input bias current of 3.5 nA, and low supply-current consumption of approximately 200 uA per comparator. The open-collector output structure is compatible with TTL, MOS, and CMOS logic when the appropriate pull-up is used. The comparator also supports a faster response time than many older standard quad comparators. Because all four channels share the same supply pins, the device is most appropriate when the compared signals operate within the same supply system. The 14-SOIC package provides a conventional surface-mount footprint and broad compatibility with industrial control-board layouts. The internal architecture uses four differential comparator channels referenced to the common ground and supply rails. The input stage is designed for low offset and low bias current, reducing errors when small signal differences must be detected. The open-collector transistor remains off when the comparator output is high impedance and conducts when the output is driven low. The external pull-up resistor determines the high-state voltage and limits the current through the output transistor. The maximum differential input voltage and common-mode voltage limits must be respected during startup, fault conditions, and signal transients. The manufacturer datasheet is the authoritative source for absolute maximum ratings, electrical limits, timing characteristics, and the complete pin configuration. Typical uses include monitoring a battery or power rail, detecting an overvoltage or undervoltage condition, comparing a thermistor or divider output with a reference, and providing a fault flag in industrial equipment. The four channels can also implement independent window comparisons when suitable resistor networks are used. Open-collector outputs are particularly useful when multiple comparators must signal one system event through a common pull-up node. In motor-control, power-supply, and instrumentation circuits, the device can provide a hardware threshold decision before a controller reacts, reducing the processing burden on the controller. The principal design consideration is the pull-up network on every open-collector output. Select the resistor to balance rise time against output-transistor dissipation and required logic current. Keep comparator inputs away from noisy power-switching nodes, use a stable reference for precision thresholds, and account for input common-mode limits. When replacing another quad comparator, verify the complete pinout, output architecture, supply range, input offset, response time, and temperature rating before production use. The LM2901DE4 is a standard general-purpose choice for designs requiring four channels, wide supply tolerance, and flexible open-collector interfacing.

RFQ İletişim
LM2901DG - Quad Comparator, 3-36 V, 14-SOIC | onsemi
LM2901DG

LM2901DG - Quad Comparator, 3-36 V, 14-SOIC | onsemi

The onsemi LM2901DG is a single-supply quad differential comparator with four general-purpose channels, a 3 V to 36 V supply range, open-collector CMOS/TTL-compatible outputs, and a 14-pin SOIC package. Each channel offers a typical response time of 1.3 us, making the device suitable for level detection, low-level sensing, and memory applications. The package supports both single and split-supply operation. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four independent channels can evaluate separate thresholds, monitor multiple control signals, or implement sensing functions where a logic-compatible indication is preferable to a continuously amplified analog output. Key features include a wide 3 V to 36 V single-supply operating range, dual-supply operation from ±1.5 V to ±18 V, and open-collector outputs compatible with CMOS and TTL. The maximum input bias current is 0.25 uA at 5 V, while typical low-level specifications include 25 nA input bias current, ±5 nA input offset current, and 130 mV low-output saturation voltage at 4 mA. These characteristics make the device appropriate for low-current threshold-detection circuits. The four comparators share a common supply arrangement but operate independently, allowing separate reference and signal inputs for each channel. Open-collector outputs require an external pull-up resistor and can be wired for wired-AND behavior. The LM2901DG is identified as a CMOS, open-collector, TTL-compatible device, making it suitable for interfacing with both older TTL logic and CMOS control systems. Response time remains short enough for supervisory, sequencing, and discrete threshold applications. Typical uses include industrial control-system threshold detection, automotive sensing interfaces, consumer equipment level supervision, and memory-device address or control comparisons. The 3 V minimum supply also permits operation from regulated 5 V rails, while the 36 V maximum supports higher-voltage industrial systems when suitable input protection is applied. Each open-collector output can directly drive a pull-up-connected digital input or relay driver stage. For robust PCB design, place the pull-up resistor close to the output and maintain short, stable traces for sensitive threshold inputs. Account for input offset voltage when the decision point is critical, and prevent unused comparator inputs from floating. Confirm absolute maximum input and output ratings against the system rails before applying signals near the supply limits. This page combines the LM2901DG operating envelope, drop-in comparison data, pin and package guidance, and application-oriented design notes. It also distinguishes the device from electrically similar quad comparators so engineers can assess supply range, output architecture, common-mode behavior, and timing before replacing an existing part.

RFQ İletişim
LM2901DG4 - 30V Quad Differential Comparator | Texas Instruments
LM2901DG4

LM2901DG4 - 30V Quad Differential Comparator | Texas Instruments

The Texas Instruments LM2901DG4 is a 30 V quad differential comparator containing four independent comparison channels, an input common-mode range that includes ground, and open-collector outputs in a 14-pin SOIC package. Its maximum-rated supply voltage reaches 38 V, while the published operating supply range is 2 V to 36 V. The device provides low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, and low supply current of 200 µA per comparator. A differential comparator is a semiconductor that compares two input voltages and changes its output when one input becomes higher than the other. The LM2901 belongs to the comparator hierarchy within analog integrated circuits, where it provides a simple binary decision function for control, sensing, and protection circuits. Each of its four channels is electrically independent, allowing one package to perform four separate threshold comparisons without requiring four single-comparator packages. The LM2901 supports single-supply or dual-supply operation, making it adaptable to systems using 2 V to 36 V rails. Its differential input voltage range can equal the maximum-rated supply voltage, and its open-collector outputs allow wired-AND behavior when an external pull-up is used. The low 200 µA supply current per comparator is useful in battery-operated equipment, while the 0.37 mV input offset helps preserve accuracy in low-level sensing applications. The 300 ns response time supports comparisons in switching and control loops where propagation delay matters. Outputs are compatible with TTL, MOS, and CMOS logic, which simplifies interfacing with microcontroller input pins, logic gates, relay drivers, and open-collector devices. Unlike an op-amp configured as a comparator, the LM2901 is intended specifically for open-loop threshold comparison and does not include the feedback network normally associated with linear amplification. Typical uses include industrial sensor threshold detection, overvoltage and undervoltage monitoring, battery discharge indication, temperature-limit switching, motor or actuator control, and four-channel digital sensing. The common-mode input range that includes ground is particularly useful for detecting signals near 0 V. In systems with multiple open-collector outputs, an external pull-up resistor is required to establish a valid high output level. Design the PCB with short comparator input traces, a solid ground reference, and careful separation between sensitive input nodes and output or pull-up paths. The open-collector output must never remain connected directly to a supply rail without a suitable pull-up. Confirm actual output sink current, input common-mode limits, and supply behavior against the manufacturer datasheet for the exact operating condition. This product page combines the LM2901DG4 electrical specifications, a complete 14-SOIC pin map, same-footprint alternatives, and application guidance. It is designed to help engineers make a compatibility decision quickly while still validating the final circuit against the manufacturer datasheet.

RFQ İletişim
LM2901DR2 - Quad Open-Collector Comparator | onsemi
LM2901DR2

LM2901DR2 - Quad Open-Collector Comparator | onsemi

onsemi LM2901DR2 is a quad differential voltage comparator with four independent channels, an operating supply range of 3 V to 36 V, and a 14-pin SOIC package. Its open-collector outputs support level detection and interface to compatible logic systems, while its typical input bias current of 25 nA suits low-level sensing applications. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901DR2 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Each of its four channels can operate independently, allowing multiple thresholds, window-detection functions, or simple control decisions to be implemented within one device. The principal features include four comparator channels, a 3 V to 36 V supply range, open-collector outputs, and a typical input bias current of 25 nA. Open-collector outputs provide flexibility when the output must be pulled up to a local supply rail or connected to wired logic. They are not intended to source output current directly, so an external pull-up resistor is normally required. The LM2901DR2 can operate from a single supply or from split supplies, which makes it adaptable to industrial, automotive, and consumer signal-conditioning circuits. Its differential input arrangement allows one input to act as the reference and the other as the sensed signal. Because this is an analog comparator rather than a logic gate, designers should account for input offset voltage, common-mode range, propagation delay, output pull-up requirements, and supply decoupling when defining switching thresholds. Typical uses include battery threshold detection, sensor-limit switching, window comparators, level translation, relay or LED drive, automotive interface circuits, and industrial control inputs. A four-channel implementation can also reduce component count when several independent sensing points must be monitored in the same circuit. When laying out a design, place the bypass capacitor close to the supply pin and route comparator inputs away from switching nodes and high-current paths. Select the pull-up resistor for the required sink current and switching speed, and verify that every input remains inside the device's common-mode range across temperature and supply tolerance. The manufacturer datasheet pin description should be used when assigning PCB tracks. This product page combines the manufacturer-level electrical characteristics, confirmed SOIC-14 alternatives, sourcing guidance, application analysis, and practical PCB considerations needed to evaluate the LM2901DR2 before incorporating it into a new design.

RFQ İletişim
LM2901DR2G - Quad Open-Collector Comparator | onsemi
LM2901DR2G

LM2901DR2G - Quad Open-Collector Comparator | onsemi

onsemi LM2901DR2G is a quad differential comparator for consumer, automotive, and industrial electronics, operating from 3 V to 36 V over a temperature range of -40°C to +105°C. The device provides four independent comparison channels in a 14-pin SOIC package, with open-collector outputs suitable for CMOS, TTL, and wired-interface signaling. Its single-supply architecture simplifies threshold detection and low-level sensing designs that require a practical supply range for both industrial and automotive equipment. A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level output indicating which input is higher. Within the broader semiconductor hierarchy, the LM2901 belongs to the comparator family, which sits alongside amplifiers, voltage references, and other analog signal-conditioning ICs. The LM2901 is particularly useful when a system must translate an analog threshold crossing into a digital event for control logic, memory, monitoring, or protection circuitry. The principal features of the LM2901DR2G include four differential comparator channels, a 3 V to 36 V single-supply operating range, an open-collector output architecture, and compatibility with CMOS and TTL loads. Open-collector outputs permit the output stage to be pulled up to the voltage required by the receiving logic. Designers can therefore select the pull-up voltage independently of the comparator supply, provided it remains within the device's applicable operating limits. The quad arrangement consolidates four comparison functions into one 14-SOIC package. This can reduce component count and board area in designs requiring multiple threshold decisions, such as battery monitoring, window comparison, signal crossing detection, and industrial control inputs. The open-collector architecture is also useful when several outputs must share a common bus or when an external pull-up defines the logic-high level. External pull-up resistors and output-rise-time analysis remain essential design considerations. Typical uses include automotive battery and power-system monitoring, industrial sensor interfaces, consumer threshold detection, memory-control logic, and general industrial control systems. The -40°C to +105°C operating range supports applications across wide environmental conditions, while the 36 V upper supply limit accommodates higher-voltage industrial and automotive rails. Designers should verify input common-mode limits, output pull-up requirements, and input-current behavior against the manufacturer datasheet for the exact operating conditions. When laying out an LM2901DR2G circuit, place pull-up resistors close to the open-collector outputs and keep sensitive threshold networks away from switching nodes and high-current return paths. Because the device is intended for level detection and low-level sensing, input filtering, hysteresis, and stable reference generation often matter more than high-speed signal fidelity. The component should be selected only after checking the complete datasheet limits for supply voltage, input common-mode range, output current, and electrical characteristics. This page combines the exact LM2901DR2G configuration with same-package alternatives, application-specific engineering guidance, a parameter comparison table, and practical layout considerations. These details help buyers distinguish the 14-SOIC part from other LM2901 order codes and assess whether it is appropriate for a new industrial, automotive, or consumer circuit without changing the PCB footprint.

RFQ İletişim
LM2901M - 4-Channel 36V Open-Collector Comparator | Texas Instruments
LM2901M

LM2901M - 4-Channel 36V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2901M is a four-channel differential analog comparator with an operating supply range of 2 V to 36 V, a typical response time of 1.3 µs, and open-collector outputs in a 14-pin SOIC package. Designed for single-supply operation, it can also operate from dual supplies providing approximately ±1 V to ±18 V. Each comparator compares two input voltages and produces a digital result that can drive TTL, MOS, or CMOS-compatible logic. The package is identified by the M suffix and is suitable for conventional through-hole PCB assembly when surface-mount assembly is not required. An analog comparator is a semiconductor that converts the relationship between two voltages into a logic-level output. The LM2901 belongs to the comparator hierarchy, where a general-purpose comparator is used for threshold detection, signal conditioning, and industrial control rather than precision analog amplification. Its wide supply range, low input bias current, and low typical supply-current consumption make it suitable for systems operating from low-voltage control circuits through higher-voltage industrial environments. The principal features include four independent comparator channels, an approximate 36 V maximum supply, 800 µA typical supply-current drain, 25 nA typical input bias current, and open-collector outputs suitable for wired logic. These characteristics allow the device to monitor slow and fast control signals while maintaining low loading on high-impedance sensor nodes. The open-collector architecture also supports wired-AND behavior when multiple comparators share a pull-up resistor, although the common output node requires careful voltage and timing analysis. Each internal comparator has an inverting input, a non-inverting input, and an open-collector output. The open-collector transistor normally remains off, so an external pull-up resistor is required to establish a high output state. When the comparator output is pulled low, the output transistor sinks current from that pull-up network. The resulting interface can support wired logic, relay-driver stages, lamp indicators, and other systems where a pulled-up bus must be shared safely. Typical applications include industrial sensor-limit detection, overvoltage and undervoltage monitoring, battery threshold detection, control-system interlock circuits, and logic-level translation around higher-voltage signals. The four channels can be used independently, or several channels can implement window comparison, fault detection, and redundant monitoring functions. A common ground and supply arrangement simplifies multi-channel designs while requiring attention to common-mode limits, output pull-up placement, and input protection. The principal design consideration is ensuring that input and output conditions remain within the comparator's absolute maximum and common-mode limits. Input protection may be required when external wiring exposes the device to transients or voltages outside the normal operating range. The open-collector outputs also need suitable pull-up resistors, with resistance selected from the required sink-current, rise-time, and bus-loading constraints rather than from resistance alone. This page combines manufacturer specifications, verified distributor information, pin-level implementation guidance, and same-footprint replacement analysis. It also identifies the practical trade-offs among closely related LM2901-family ordering options so that engineers can distinguish electrical compatibility, package identity, and qualification differences before committing a design to production.

RFQ İletişim
LM2901M96 - 30V Quad Differential Comparator | Harris
LM2901M96

LM2901M96 - 30V Quad Differential Comparator | Harris

The Harris LM2901M96 is a low-power quad differential voltage comparator designed for general-purpose signal conditioning and logic-interface applications. It contains four independent comparison channels in a 14-pin SOIC package and operates from a single or dual supply, with a common-mode input voltage range that includes ground. The device is identified by the manufacturer as a 30-V quad differential comparator, making it suitable for industrial control, sensor interface, and low-voltage logic applications. A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital-level output indicating their relationship. The LM2901M96 belongs to the comparator, analog IC, and semiconductor hierarchy. Its four independent channels allow one package to implement multiple threshold decisions, monitoring functions, or logic decisions. Open-collector outputs are compatible with TTL, CMOS, MOS, DTL, and ECL logic families, enabling the device to operate as an interface between analog sensing circuits and digital logic. Key features include low power consumption, a common-mode input range extending to ground, and open-collector output structure. The common-mode capability is important for single-supply designs in which the sensed signal can approach the lower supply rail. The open-collector outputs can also be pulled up to an appropriate supply voltage and used to drive multiple open-collector-compatible loads when the current and speed requirements are satisfied. The LM2901M96 is a quad comparator rather than a precision instrumentation amplifier or a dedicated logic gate. Each channel compares its non-inverting and inverting inputs independently, allowing the device to serve as a window comparator, overvoltage detector, or simple signal translator. The M96 designation identifies the Harris packaging variant listed in a 14-SOIC configuration. Its exact electrical limits, offset voltage, response time, input bias current, and output-current ratings should be confirmed in the manufacturer datasheet before production release. Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, automotive or equipment control systems, switching power-supply fault detection, and general-purpose logic level conditioning. The comparator is particularly useful when a small analog signal must be converted into a stable digital decision before being processed by a microcontroller or logic gate. For reliable implementation, maintain adequate input common-mode headroom, respect the maximum supply and differential-input ratings, and provide pull-up resistors on each open-collector output. Check output timing against the propagation delay and the required system response time. This page combines manufacturer-family information, package details, sourcing guidance, compatible drop-in options, and practical design considerations for engineers evaluating the LM2901M96.

RFQ İletişim
LM2901MWA Quad Open-Collector Comparator | Texas Instruments
LM2901MWA

LM2901MWA Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2901MWA is a four-function differential analog comparator offered in wafer-sale form for industrial-temperature applications. It combines a maximum input offset voltage of 7000 uV, a response time of 1300 ns, a maximum supply current of 2 mA, and an operating temperature range of -40°C to +85°C. The device provides open-collector outputs suitable for TTL, MOS, and CMOS interfacing. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level indication of their relative relationship. The LM2901 belongs to the comparator hierarchy within analog signal conditioning and power-management electronics. Its four independent channels make it suitable when several sensing or threshold decisions must be performed in one package. The common-mode input range includes ground, while differential input voltage can reach the maximum-rated supply voltage of ±38 V. The principal features support robust threshold detection and low-level sensing. Open-collector outputs allow the output state to be established with an external pull-up resistor, which provides flexibility for interfacing to mixed logic families and for wired-AND arrangements. The 7000 uV maximum offset specification defines the worst-case input-voltage difference that can affect switching behavior, while the 1300 ns response time establishes the nominal propagation performance of the comparator. Each of the four comparator channels is independent, allowing separate sensing tasks within a single die. The industrial temperature rating supports equipment operating across a broad ambient range, and the 2 mA maximum supply current suits low-power signal-conditioning systems. The LM2901 family is commonly used for level detection, low-level sensing, and memory-related control functions, where a voltage threshold must be translated into a digital state. Typical uses include industrial sensor interfaces, overvoltage and undervoltage detection, battery threshold monitoring, window comparators, and control logic for power systems. Because the output is open collector, the designer can select the pull-up voltage and resistor to match the receiving logic rather than relying on a fixed active-high or active-low output arrangement. LM2901MWA is supplied as an unpackaged die rather than a conventional leaded or surface-mount package. Board-level implementation therefore requires wafer handling, die attachment, bonding, encapsulation, and qualification of the assembled product. Its absence from the package library and the lack of a public package pin numbering are important constraints when planning assembly or comparing it with packaged LM2901 devices. This page combines the LM2901MWA ordering characteristics, functional limits, comparator specifications, interface considerations, and procurement guidance with a separate evaluation of true drop-in alternatives. Because the target is a wafer-sale die, only an equivalent offered in the same physical form can qualify as a drop-in replacement; standard SOIC or DIP implementations are electrically related but are not interchangeable on a PCB.

RFQ İletişim
LM2901N - Quad Open-Collector Comparator | Texas Instruments
LM2901N

LM2901N - Quad Open-Collector Comparator | Texas Instruments

Texas Instruments LM2901N is a general-purpose quad differential comparator containing four independent comparator channels in a 14-pin through-hole DIP package. Each channel compares two input voltages and provides an open-collector output that can pull a logic node low or be released to a pull-up resistor. The device operates from a single supply or from split supplies, with a wide supply-voltage range extending to approximately 36 V. A comparator is a differential amplifier used to evaluate the relationship between two voltages. When the non-inverting input exceeds the inverting input, the associated output transistor turns on; reversing the inputs reverses the output state. The LM2901N belongs to the comparator hierarchy, which includes differential comparator ICs, analog interface ICs, and broader semiconductor signal-conditioning devices. Its four independent channels make it useful when a design requires multiple threshold, level, or sensing decisions. Important characteristics include a typical input bias current of 25 nA, typical input offset current of ±5.0 nA, and low supply-current consumption. The open-collector architecture is especially useful for wired logic, relay-driving interfaces, and systems that share a pull-up rail. Unlike a push-pull output, an open-collector output requires an external pull-up resistor and can safely combine multiple driver nodes when the device ratings and pull-up design are appropriate. The four channels share supply and ground pins but have independent inputs and outputs. This arrangement supports simultaneous comparisons, window detection, and complementary decision logic. Because the outputs are open collector, external pull-up resistors determine the high-state voltage and can be tied to TTL-, CMOS-, or MOS-compatible logic levels. The input arrangement permits sensing signals referenced to ground while the supply rail provides the comparator's operating voltage. Typical applications include industrial level detection, low-level sensing, consumer and automotive threshold decisions, memory and window-comparison circuits, and general-purpose control logic. The LM2901N is particularly appropriate when the design needs several channels, a wide supply range, low input bias current, and flexible output pull-up rather than rail-to-rail push-pull outputs. It is also useful in systems where output transistors must remain off until a wired-AND condition is satisfied. A key design consideration is the pull-up network. Select its resistance to balance rise time, output-sink current, power consumption, and the number of outputs connected to one node. Also route the four differential input pairs away from noisy supply and switching-current paths, because comparator input offset can determine the actual switching threshold. Confirm output-state behavior, input common-mode limits, and supply sequencing against the manufacturer datasheet before finalizing the circuit. This product page combines manufacturer information, distributor listings, package details, and practical comparator design guidance. It also identifies same-package alternatives and organizes the technical trade-offs for engineers comparing the LM2901N with other quad differential comparators before making a PCB-compatible sourcing decision.

RFQ İletişim
LM2901N/PB - Quad Open-Collector Comparator | Texas Instruments (Lead-Free (Pb-Free))
LM2901N/PB

LM2901N/PB - Quad Open-Collector Comparator | Texas Instruments (Lead-Free (Pb-Free))

Texas Instruments LM2901N/PB is a general-purpose quad differential comparator containing four independent comparator channels in a 14-pin through-hole DIP package. Each channel compares two input voltages and provides an open-collector output that can pull a logic node low or be released to a pull-up resistor. The device operates from a single supply or from split supplies, with a wide supply-voltage range extending to approximately 36 V. A comparator is a differential amplifier used to evaluate the relationship between two voltages. When the non-inverting input exceeds the inverting input, the associated output transistor turns on; reversing the inputs reverses the output state. The LM2901N/PB belongs to the comparator hierarchy, which includes differential comparator ICs, analog interface ICs, and broader semiconductor signal-conditioning devices. Its four independent channels make it useful when a design requires multiple threshold, level, or sensing decisions. Important characteristics include a typical input bias current of 25 nA, typical input offset current of ±5.0 nA, and low supply-current consumption. The open-collector architecture is especially useful for wired logic, relay-driving interfaces, and systems that share a pull-up rail. Unlike a push-pull output, an open-collector output requires an external pull-up resistor and can safely combine multiple driver nodes when the device ratings and pull-up design are appropriate. The four channels share supply and ground pins but have independent inputs and outputs. This arrangement supports simultaneous comparisons, window detection, and complementary decision logic. Because the outputs are open collector, external pull-up resistors determine the high-state voltage and can be tied to TTL-, CMOS-, or MOS-compatible logic levels. The input arrangement permits sensing signals referenced to ground while the supply rail provides the comparator's operating voltage. Typical applications include industrial level detection, low-level sensing, consumer and automotive threshold decisions, memory and window-comparison circuits, and general-purpose control logic. The LM2901N/PB is particularly appropriate when the design needs several channels, a wide supply range, low input bias current, and flexible output pull-up rather than rail-to-rail push-pull outputs. It is also useful in systems where output transistors must remain off until a wired-AND condition is satisfied. A key design consideration is the pull-up network. Select its resistance to balance rise time, output-sink current, power consumption, and the number of outputs connected to one node. Also route the four differential input pairs away from noisy supply and switching-current paths, because comparator input offset can determine the actual switching threshold. Confirm output-state behavior, input common-mode limits, and supply sequencing against the manufacturer datasheet before finalizing the circuit. This product page combines manufacturer information, distributor listings, package details, and practical comparator design guidance. It also identifies same-package alternatives and organizes the technical trade-offs for engineers comparing the LM2901N/PB with other quad differential comparators before making a PCB-compatible sourcing decision.

RFQ İletişim
LM2901NG - 3-36 V Quad Comparator for Level Detection | onsemi
LM2901NG

LM2901NG - 3-36 V Quad Comparator for Level Detection | onsemi

The onsemi LM2901NG is a single-supply quad differential comparator with a 3 V to 36 V operating range, four open-collector outputs, and a 14-pin PDIP package. It is designed for level detection, low-level sensing, and memory applications, with an operating temperature range of -40°C to 105°C. Each of the four independent channels compares an inverting input with a non-inverting input and supports TTL, CMOS, and open-collector interfacing. A quad comparator is a multi-channel analog semiconductor that decides whether one input voltage is above or below another reference voltage. The LM2901NG belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used to produce a digital, logic-level decision from two analog voltages. Its four independent channels allow a compact circuit to monitor several thresholds, levels, or memory-control signals without requiring four separate comparator packages. The principal features include a 3 V to 36 V supply range, single-supply operation, and a low output saturation voltage of 130 mV at 4 mA. The common-mode input range includes ground, making the device practical for single-supply systems in which signals remain near the lower rail. ESD input clamps improve reliability without changing normal comparator operation, while the open-collector outputs permit wired logic, pull-up resistor selection, and compatibility with multiple logic families. Within the LM2901 family, the NG suffix identifies the onsemi 14-pin PDIP configuration. The device provides four separate comparator channels rather than a single comparison function, reducing package count when several independent decisions are required. Its open-collector outputs require an external pull-up when the output must rise to a defined positive voltage. Designers should account for the pull-up value, output leakage, input bias current, and propagation delay when driving long interconnects or switching high-capacitance nodes. Typical applications include industrial sensor threshold detection, battery-powered equipment, memory-control logic, window or level comparators, and general-purpose TTL or CMOS interfacing. Because the operating range extends to 36 V, the LM2901NG can be used in higher-voltage industrial systems when every input remains inside its permitted common-mode range. The -40°C to 105°C temperature range supports both commercial and extended industrial environments. For reliable operation, use the pin-description table and typical application information in the onsemi datasheet when assigning input polarities and output pull-ups. Keep sensitive analog input traces away from high-current switching nodes, provide a stable local supply connection, and select a pull-up resistor that balances rise time against output-driver loading. Input and output filtering may be required when the comparator is used near switching regulators or fast digital signals. This product page combines the manufacturer specifications with package, application, comparison, and design guidance for engineers evaluating LM2901NG. It also identifies qualified same-package alternatives and highlights the electrical and application trade-offs that should be checked before a replacement is approved for an existing PCB.

RFQ İletişim
LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments
LM2901NG4

LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2901NG4 is a four-channel general-purpose differential comparator with open-collector outputs, single-supply operation from 2 V to 30 V, and a 14-PDIP package. Each of the four independent channels compares two input voltages and provides a logic-level indication of their relationship. The open-collector architecture allows the outputs to be pulled up to a suitable logic voltage and enables wired-AND operation when multiple channels share an output node. A comparator is an analog integrated circuit that converts the relationship between two voltages into a binary result. The LM2901 belongs to the voltage-comparator hierarchy within the broader amplifier and comparator IC family. Its four independent channels make it useful when a system needs several threshold, level, or crossing-point decisions without using four separate single comparator packages. The LM2901NG4 supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V. According to the manufacturer product page, its outputs are compatible with TTL, MOS, and CMOS logic. The wide supply range allows the same device to be used in low-voltage control circuits and higher-voltage industrial interfaces, provided each input and output node remains within its applicable voltage limits. Each comparator channel is electrically independent, allowing four separate threshold decisions within one package. The open-collector output requires an external pull-up resistor to establish a valid high output state. This arrangement provides flexible interface-voltage selection and can improve system fault tolerance because a wired output can be pulled down by more than one channel. The device does not actively drive the output high. Typical applications include industrial control and threshold detection, instrumentation signal conditioning, sensor-interface decisions, level translation, and general analog signal processing. The four-channel organization is particularly useful for monitoring multiple control lines, implementing window comparators, or creating digital alarm logic. Open-collector outputs also suit systems that require a wired-AND bus or a pull-up voltage different from the comparator supply. When laying out a circuit, place the pull-up resistor and any input filtering components close to the relevant device pins, and route sensitive analog inputs away from switching nodes. Verify the common-mode range, differential input range, supply limits, and output pull-up voltage for the exact operating conditions. The 14-PDIP package is intended for through-hole assembly rather than compact surface-mount designs. This page combines the LM2901NG4 operating limits, interface characteristics, application guidance, package details, and validated drop-in alternatives with practical design notes for engineers comparing legacy quad comparators.

RFQ İletişim
LM2901PWR - Quad 30V Open-Collector Comparator | Texas Instruments
LM2901PWR

LM2901PWR - Quad 30V Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2901PWR is a general-purpose quad differential comparator with four independent comparison channels, a 30 V supply rating, open-collector outputs, and a 14-pin TSSOP package. Its headline characteristics include an input offset voltage of 0.37 mV, input bias current of 3.5 nA, and supply current of 200 µA per comparator, making it suitable for precision threshold detection, industrial control, and general-purpose signal conditioning. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901 belongs to the broader hierarchy of comparator integrated circuits, analog interface circuits, and semiconductor signal-conditioning devices. Unlike an operational amplifier used primarily for linear amplification, each comparator channel is intended for fast binary decision-making, level crossing, window detection, and open-drain interface signaling. Four independent channels reduce package count in multi-channel threshold systems. According to the Texas Instruments datasheet, the LM2901 has a response time of 1 µs, an input offset voltage as low as 0.37 mV, and input bias current of 3.5 nA. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic and can sink current from multiple open-collector nodes when an external pull-up is installed. The common-mode input range includes ground, which makes the device useful for detecting signals referenced to 0 V. The differential input range can equal the maximum-rated supply voltage of ±38 V for appropriate applications. A 14-pin TSSOP provides a compact surface-mount format, while the open-collector architecture requires an external pull-up resistor and leaves the output node in a high-impedance state whenever the output transistor is off. Typical uses include industrial sensor thresholds, battery monitoring, overvoltage detection, motor-control interfaces, window comparators, and logic-level translation. Four channels can monitor multiple rails or compare several sensor outputs with the same comparator. The low 200 µA per-comparator supply current also makes the device suitable for mixed-signal systems where each active channel must consume limited power. For reliable operation, select a pull-up resistor that keeps the output within the receiving logic family's voltage limits, route the exposed or sensitive inputs away from switching nodes, and account for input common-mode limits at every operating point. Because the outputs are open collector, a pull-up resistor is mandatory whenever a valid high output level is required. This product page combines the manufacturer specifications, package and pinout information, qualified replacement choices, comparison parameters, and practical circuit guidance. It supports faster component identification while making the implementation trade-offs of the LM2901PWR's four-channel, open-collector architecture clear.

RFQ İletişim
LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics
LM2901Q4T

LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2901Q4T is a four-channel low-power voltage comparator with a 2 V to 36 V single-supply range, support for ±1 V to ±18 V dual supplies, and a 16-QFN exposed-pad package measuring 3 mm by 3 mm. Each of its four channels compares an inverting input with a non-inverting input and supports open-collector output operation compatible with CMOS, DTL, TTL, MOS, and ECL logic families. A voltage comparator is an analog mixed-signal IC that evaluates two input voltages and changes its output when the difference crosses a defined threshold. The comparator category belongs to the broader interface IC and signal-conditioning hierarchy. Open-collector outputs permit several comparator outputs to share a wired bus when an external pull-up is present, making quad comparators useful for monitoring four independent signals in one compact device. The LM2901Q4T combines four independent comparison channels with very low supply current of 1.1 mA, input offset voltage of 1 mV, input bias current of 25 nA, and response times of 1.3 microseconds. Its rail-to-rail input capability lets each channel operate across the supply range. The operating-temperature range of -40°C to +125°C supports industrial and extended-temperature equipment, while the 3 mm by 3 mm QFN-16-EP package reduces board area compared with larger quad comparator packages. Each open-collector output can sink current while remaining in a high-impedance state when inactive. This architecture requires a pull-up resistor to establish a logic-high voltage. Because the output transistor can remain off, several channels may be connected to a common bus only when their wired-collector behavior and application logic are compatible. Input and output timing should be evaluated together when detecting slow crossings, short pulses, or noisy thresholds. Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, sensor threshold conditioning, window comparison, power-supply sequencing, and four-channel logic-level translation. The 2 V to 36 V supply range is particularly useful when the comparator must monitor signals above a conventional 5 V logic rail while operating from a higher system supply. For PCB design, place bypass capacitance close to the supply pins and route the exposed pad to a thermal copper area according to the manufacturer land pattern. Keep sensitive inverting and non-inverting traces short, avoid routing them beside high-current switching paths, and select the external output pull-up to establish the required logic-high level and sink-current margin. This product page combines exact electrical and package attributes, application-specific engineering guidance, threshold-level design notes, and a parameter comparison framework. It also distinguishes confirmed drop-in replacements from functionally similar devices whose channel count, package, or electrical behavior prevents direct PCB substitution.

RFQ İletişim