Ürünler (44.000+)

MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP
MC33171PG

MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP

The onsemi MC33171PG is a single general-purpose operational amplifier in an 8-pin plastic DIP package, specified for single-supply operation from 3.0 V to 44 V. It combines a 1.8 MHz gain-bandwidth product with a 2.1 V/us slew rate and a low quiescent current of 180 uA per amplifier. The device is designed for low-power instrumentation, industrial signal conditioning, sensor amplification, and control applications requiring operation from a single supply. An operational amplifier, or op amp, is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Its hierarchy extends from general-purpose amplification to signal conditioning, analog mixed-signal ICs, and broader power-management-aware system design. The MC33171/72/74 family uses bipolar fabrication without JFET input transistors, combining low supply current with adequate bandwidth and slew rate for many industrial signal paths. Key electrical characteristics include a 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and approximately 180 uA operating current per amplifier. The wide 3.0 V to 44 V single-supply range allows operation from conventional 5 V, 12 V, 24 V, and higher industrial rails. The MC33171PG is specified across a -40C to +85C temperature range, while its input bias current is listed at 20 nA and input offset voltage at 2 mV. The MC33171 series is particularly suited to single-supply operation but can also be used with split supplies when the circuit and common-mode conditions permit. Its bipolar input stage avoids the need for JFET technology, and the 1.8 MHz bandwidth supports audio-frequency and general instrumentation tasks. The 2.1 V/us slew rate improves large-signal response compared with strictly low-bandwidth precision amplifiers, although the device remains a general-purpose rather than a high-speed amplifier. Typical applications include low-frequency sensor conditioning, transducer amplification, process-control loops, industrial current or voltage monitoring, audio preamplification, and general-purpose analog filtering. For higher-impedance sensors, the 20 nA input bias specification helps minimize loading, while the 2 mV input offset must be considered in precision measurement paths. Feedback-network layout, grounding, and supply bypassing remain important at the board level. When designing around the MC33171PG, check input and output voltage swing at the intended load because single-supply operation restricts the usable signal range near the rails. Place bypass capacitors close to the supply pins, route feedback paths away from high-current inputs, and verify stability with the selected gain, load capacitance, and compensation network. For an obsolete legacy design, confirm availability before committing to new production layouts. This page combines lifecycle status, package details, verified electrical characteristics, replacement guidance, and board-level design notes for engineers maintaining MC33171PG-based instrumentation. It also compares same-footprint amplifier options and highlights the trade-offs among supply current, bandwidth, input offset, and operating-temperature range.

RFQ İletişim
MC33172D - Low-Power Dual Op Amp | STMicroelectronics
MC33172D

MC33172D - Low-Power Dual Op Amp | STMicroelectronics

The STMicroelectronics MC33172D is a low-power dual bipolar operational amplifier with two amplifier circuits, a gain-bandwidth product of 1.8 MHz, and an 8-pin SOIC package. It is designed for general-purpose signal conditioning applications where two independent amplifiers are useful in a single package. An operational amplifier is a voltage-controlled differential amplifier that compares two input voltages and amplifies their difference. Operational amplifiers form part of the broader analog IC and active-signal-processing hierarchy. The MC33172D uses bipolar transistor input stages and is suitable for functions such as buffering, gain amplification, comparisons, filtering, and instrumentation interfaces when configured with suitable external resistors and capacitors. Each MC33172D channel provides a practical combination of low power consumption and general-purpose signal handling. The device contains two amplifier circuits in one 8-SOIC package, reducing component count and board area in designs requiring paired amplification. Its listed maximum input offset voltage is 6.5 mV, while its unity-gain bandwidth is 1.8 MHz. These characteristics suit signal paths that do not require the very low offset, very high bandwidth, or very low noise associated with specialized precision amplifiers. The bipolar architecture is appropriate for low-frequency control, measurement, and conditioning circuits where the amplifier operates mainly in a closed-loop configuration. Noise, offset, input common-mode range, output swing, supply current, and stability characteristics must be checked against the actual signal amplitude and frequency before the device is used. Negative feedback, adequate output loading, and input-referenced compensation should follow the manufacturer's recommended application circuits. Typical applications include dual-axis sensor signal conditioning, active filtering, audio preamplification, threshold detection, low-frequency instrumentation, and general industrial control. Two channels can also implement differential or complementary signal processing when their inputs and outputs are configured appropriately. The 8-SOIC package is easy to assemble with conventional surface-mount production equipment and can simplify upgrades compared with discrete single-amplifier packages. Designers should verify the supported supply voltage, common-mode input range, output swing, input bias current, and operating temperature against the manufacturer's datasheet. Input and output voltages must remain within the electrical limits, and unused amplifier inputs should be biased rather than left floating. Stable feedback-network values are essential at higher frequencies. This product page combines package details, searchable technical questions, application guidance, and a drop-in comparison focused on practical amplifier selection. It helps engineers distinguish the dual bipolar MC33172D from higher-speed rail-to-rail alternatives before committing a circuit board to an 8-SOIC footprint.

RFQ İletişim
MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics
MC33172N

MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics

The STMicroelectronics MC33172N is a dual bipolar operational amplifier designed for low-power signal conditioning from single or dual supplies. It provides two amplifiers in an 8-pin PDIP package, operates from +4 V to +44 V, or equivalently from ±2 V to ±22 V, and is specified for approximately 200 µA per amplifier. The device offers 2.1 MHz gain-bandwidth product and a 2 V/µs slew rate for a practical balance of speed, power consumption, and operating range. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its two inputs while using feedback to control gain, bandwidth, and output behavior. The dual-amplifier configuration places two independent amplifiers in one package, reducing board area in audio, instrumentation, industrial control, and sensor-interface circuits. MC33172N belongs to the bipolar operational-amplifier family within the broader voltage-regulator-free analog IC and semiconductor hierarchy. The headline electrical characteristics are its dual-amplifier architecture, 2.1 MHz gain-bandwidth product, 2 V/µs slew rate, and low supply current of approximately 200 µA per amplifier. These specifications make the device suitable for signals that require more bandwidth than a micropower-only amplifier but do not demand the very high speed or rail-to-rail performance of newer CMOS families. Its wide supply range also allows operation from conventional ±15 V and ±22 V analog rails. The MC3x172 series uses a bipolar input and output architecture rather than JFET input. This family construction supports operation from very low positive supplies through relatively high industrial voltage rails. Because the amplifiers are specified for both single- and dual-supply operation, the same device can be used in grounded single-supply designs, where the signal is biased around the midpoint of the supply, or in conventional dual-rail systems. Typical applications include low-frequency audio amplification, instrumentation-amplifier input stages, industrial sensor buffers, general-purpose signal conditioning, and power-supply feedback or monitoring circuits. The 8-pin PDIP package is mechanically straightforward for through-hole assembly and prototype work. The relatively low 200 µA-per-amplifier supply current is particularly useful when each active channel must remain powered continuously within a multi-channel measurement system. The principal design consideration is common-mode and output-range behavior. Designers should calculate signal swing, input bias requirements, and the effect of load current before fixing external resistor values. Because this is a bipolar amplifier rather than a rail-to-rail CMOS amplifier, input and output headroom must be checked against the selected supply voltage. Stable operation also depends on correct feedback topology and suitable output-load isolation. This product page combines the manufacturer datasheet with practical guidance for supply selection, signal conditioning, PCB implementation, and replacement assessment. It also distinguishes true pin-and-footprint-compatible options from broader functional equivalents so engineers can make a replacement decision without treating a similar amplifier as an automatic drop-in substitute.

RFQ İletişim
MC33172PG - Dual 44V Low-Power Op Amp | onsemi
MC33172PG

MC33172PG - Dual 44V Low-Power Op Amp | onsemi

The onsemi MC33172PG is a dual, low-power bipolar operational amplifier designed for general-purpose instrumentation and signal-conditioning applications. It operates from a single supply of 3.0 V to 44 V, provides two amplifiers in an 8-pin PDIP package, and supports both single-supply and split-supply operation. Its key characteristics include a 1.8 MHz gain-bandwidth product, a 2.1 V/µs slew rate, and approximately 180 mA of operating current per amplifier. An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences. The MC33172 belongs to the operational-amplifier hierarchy within analog signal-conditioning ICs. Its bipolar input stage uses conventional bipolar transistor technology rather than JFET devices, combining relatively low input-offset behavior with moderate bandwidth. The dual configuration permits two independent amplifier channels in one package, reducing board area when paired gain, filtering, or buffering functions are required. The MC33172PG is particularly suited to single-supply systems because its 3.0 V minimum supply voltage allows operation from regulated 3.3 V or 5 V rails. Split supplies are also supported when the circuit requires a bipolar signal range around ground. The 44 V maximum supply voltage provides additional headroom for higher-voltage industrial interfaces, although input and output common-mode limits must still be respected. Both channels are intended for low-power operation at approximately 180 mA per amplifier. With a gain-bandwidth product of 1.8 MHz and slew rate of 2.1 V/µs, the device is suitable for moderate-frequency precision rather than high-speed video or RF amplification. The 1.8 MHz gain-bandwidth product allows useful closed-loop bandwidth in lower-gain configurations, while the 2.1 V/µs slew rate limits large-signal response in wideband designs. These characteristics make signal rise times and stability more important than raw bandwidth in most applications. Typical uses include industrial sensor conditioning, current-loop receivers, low-frequency active filters, audio preamplification, transducer interfaces, and general-purpose buffer stages. It is especially useful when two channels can share the same supply and ground arrangement. Because the package is an 8-pin PDIP, the device is also convenient for through-hole prototyping and repair assemblies where a surface-mount footprint would be inconvenient. Design the input network, output loading, and supply decoupling around the ratings in the onsemi MC33172 datasheet. Place bypass capacitors close to the supply pins, observe the input common-mode range, and avoid driving capacitive loads unless stability compensation is provided. Confirm the exact pin assignments and operating limits against the manufacturer pin-description table before finalizing a PCB layout. This product page combines the manufacturer specifications, commercial guidance, same-package replacement analysis, and application-oriented design considerations. It supports faster part selection while keeping the decisive checks—supply range, amplifier bandwidth, package, pin compatibility, and common-mode limits—visible at the design stage.

RFQ İletişim
MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics
MC33174D

MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics

STMicroelectronics MC33174D is a low-power quad bipolar operational amplifier with 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The device is offered in a 14-pin SOIC package and supports single-supply operation from +4 V to +44 V. Its input common-mode range extends to the lower supply rail, making it useful in low-side sensing and single-supply signal chains. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. MC33174D belongs to the broader amplifier IC, analog IC, and semiconductor hierarchies. Unlike an amplifier built around JFET input devices, this bipolar implementation combines low supply consumption with useful low-frequency bandwidth and slew performance for general-purpose analog signal conditioning. The four amplifiers provide flexible circuit partitioning for industrial instrumentation, sensor interfaces, active filters, and control loops. Key characteristics include 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The input common-mode range reaches the lower supply rail, which simplifies designs powered from a single positive rail while the signal approaches the lower operating limit. Operation from +4 V to +44 V gives the device broad supply-voltage flexibility. The 14-pin SOIC package supports conventional surface-mount assembly, while the quad channel count consolidates four amplifiers into one component. The manufacturer datasheet identifies the MC3x174 family as low-power bipolar operational amplifiers that combine low consumption with improved speed compared with basic general-purpose bipolar alternatives. Typical uses include low-side current sensing, buffered sensor outputs, precision signal conditioning, sample-and-hold circuits, active filters, and low-frequency control loops. The extended lower-rail common-mode capability is particularly valuable when a measurement begins near ground and the circuit has only one positive supply. Split-supply operation remains possible where bipolar signals or output swing are required. Designers should verify input and output voltage limits, common-mode range, output-load capability, and stability requirements against the manufacturer datasheet for the operating condition. Decoupling capacitors should be placed close to the supply pins, and each amplifier stage should be checked for output saturation during startup and overload transients. This page organizes the MC33174D specifications, package information, verified sourcing context, drop-in alternatives, comparison parameters, and application guidance into one engineering-focused reference. It also identifies the limits of the available cross-reference information so replacement decisions can be made without treating merely similar amplifier families as confirmed drop-in devices.

RFQ İletişim
MC33174DG - 3-44V Quad Low-Power Op Amp | onsemi
MC33174DG

MC33174DG - 3-44V Quad Low-Power Op Amp | onsemi

The onsemi MC33174DG is a four-channel, low-power operational amplifier built with bipolar fabrication technology, with a 3 V to 44 V single-supply operating range, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate in a 14-pin SOIC package. The device provides four amplifiers in one package, reducing board area and simplifying four-signal conditioning, buffering, or filtering designs. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the difference between two input voltages while providing high input impedance, low output impedance, and predictable closed-loop behavior. The MC33174 belongs to the operational-amplifier hierarchy within amplifier ICs and signal-conditioning electronics. It is particularly suited to single-supply operation, allowing a common-mode input range to approach the lower supply rail for many practical signal-chain applications. Key features include four amplifier channels, 1.8 MHz gain-bandwidth product, 2.1 V/µs slew rate, and operation from 3 V to 44 V. The bipolar process avoids the need for JFET input transistors, while the four-channel integration reduces the number of packages required for instrumentation and industrial control circuits. The 14-SOIC format also supports conventional surface-mount assembly and PCB layout practices. The MC33174 family is designed for instrumentation, buffer-amplifier, and general-purpose signal-conditioning applications. Its 1.8 MHz bandwidth supports moderate-frequency amplification, while the 2.1 V/µs slew rate allows relatively fast transitions through larger voltage swings. Because the device is primarily intended for single-supply systems, input and output biasing should be selected carefully when signals approach the ground rail. Typical uses include current-loop and voltage-loop signal conditioning, sensor amplification, active filtering, transducer interfaces, sample-and-hold stages, and industrial control modules. In a four-channel instrumentation design, the MC33174 can amplify four related sensor or feedback signals while sharing one supply and ground arrangement. Its industrial supply range also supports systems operating from 24 V rails, provided signal amplitudes remain within the amplifier's common-mode limits. A practical design consideration is to verify common-mode range, output swing, stability, and noise performance at the intended supply voltage. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer's recommended stable-input circuit rather than left floating. This page combines the MC33174's confirmed operating characteristics, pin-compatible family alternatives, parameter comparisons, and practical implementation guidance to support component selection, PCB reuse, and robust analog-circuit design.

RFQ İletişim
MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics
MC33174N

MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics

The STMicroelectronics MC33174N is a quad bipolar operational amplifier in a 14-pin PDIP package, combining a low supply consumption of 200 uA per amplifier with a gain-bandwidth product of 2.1 MHz and a slew rate of 2 V/uS, while operating from a single +4 V to +44 V rail. The input common-mode range extends down to the lower supply rail, which allows the four amplifiers to be used directly in single-supply systems where the signal sits near 0 V. An operational amplifier (op-amp) is a voltage-amplifier building block whose gain, bandwidth and accuracy are shaped by negative feedback around a high-gain differential input stage. The MC3x174 family is built with monolithic bipolar fabrication and provides four amplifiers in a single package, making it a member of the analog amplifier IC hierarchy: op-amp -> quad operational amplifier -> analog amplifier IC -> analog semiconductor. Because four amplifiers share one package, a quad device reduces board area, decoupling capacitor count and total part count compared with four discrete single amplifiers. Key features of the MC33174N include the 200 uA low-consumption bias current that suits battery-fed and low-leakage measurement systems, the 2.1 MHz gain-bandwidth product that supports audio-band and general instrumentation signal paths, and the 2 V/uS slew rate that limits large-signal distortion on fast transients. The wide +4 V to +44 V supply span covers industrial 24 V rails, telecom 48 V style environments and split-supply laboratory setups from a single part family, and the rail-to-rail-referenced input stage avoids the need for a mid-supply bias network. Technically, the MC33171/72/74 series uses quality bipolar fabrication with high open-loop gain and 2.1 V/uS slew rate without relying on JFET input devices, which keeps input bias current low and stable while preserving moderate input impedance. The monolithic quad arrangement also means a common die and a common bias network, so all four channels track closely in offset and bandwidth. Because the package is a through-hole PDIP-14 with generous lead spacing, the part is easy to prototype on perfboard and to socket in legacy industrial equipment where surface-mount footprints are impractical. Typical applications include low-power sensor signal conditioning on 24 V industrial loops, battery-powered portable instrumentation, active filters and audio input stages, and general-purpose amplification inside test and measurement equipment. The 44 V maximum supply also allows the part to sit directly behind a protected 24 V or 36 V field wiring with additional headroom for transients. When designing with the MC33174N, note that the amplifier is intended for single-supply operation from +4 V, and while the common-mode input range reaches the lower rail, the output swing and offset behavior near that rail still deserve checking against the signal range you need. Decouple the supply pins close to the package, keep feedback resistors in the same range so noise and offset match, and confirm the input common-mode window in your specific gain configuration before relying on signals close to ground. This page consolidates the manufacturer datasheet parameters, package and pinout detail, plus drop-in replacement candidates and practical design notes, so that you can qualify the MC33174N for a new design or an obsolescence-driven substitution without hunting through multiple documents.

RFQ İletişim
MC33174PG - 44V Quad Op Amp, 1.8MHz | onsemi
MC33174PG

MC33174PG - 44V Quad Op Amp, 1.8MHz | onsemi

The onsemi MC33174PG is a general-purpose quad operational amplifier with four amplifiers in a 14-pin plastic DIP package. Each channel supports a 3 V to 44 V single-supply operating range, while the device combines a 1.8 MHz gain-bandwidth product, 2.1 V/µs slew rate, and approximately 180 µA supply current per channel. These characteristics make it suitable for general-purpose signal conditioning where four independent amplifiers are needed on one PCB footprint. An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. A quad operational amplifier integrates four amplifiers into one package, reducing board area and simplifying multi-channel instrumentation, sensor, audio, and control designs. The MC33174 belongs to the broader operational-amplifier hierarchy, where it functions as a voltage-feedback amplifier and ultimately as a general-purpose analog signal-conditioning IC. The MC33174PG's major benefits include its wide 3 V to 44 V supply range, low 180 µA supply current per amplifier, and 1.8 MHz gain-bandwidth product. The 2.1 V/µs slew rate supports moderate-accuracy signal transitions without the operating characteristics of a high-speed precision amplifier. A 20 nA input-bias-current specification is particularly useful in sensor interfaces and bias-resistor networks, although the complete electrical limits should be checked against the required supply voltage and common-mode range. The device uses quality bipolar fabrication and provides four amplifiers in the MC33171/MC33172/MC33174 operating-amplifier family. Its electrical performance is intended for general-purpose applications rather than precision instrumentation. The 14-DIP package provides a conventional through-hole footprint with 7.62 mm row spacing, making it suitable for prototyping, industrial control equipment, legacy systems, and applications where a dual-inline package is easier to assemble or inspect. Typical uses include four-channel sensor conditioning, industrial current and voltage monitoring, audio preamplification, active filtering, relay and actuator drive, laboratory instrumentation, and embedded control boards. Because it accepts supply voltages as high as 44 V, the device can also operate in higher-voltage industrial circuits when the signal common-mode voltage, output swing, and input protection remain within the device limits. The main design consideration is the relationship among bandwidth, supply voltage, and output swing. A gain of 10 reduces the usable bandwidth to approximately 180 kHz, so higher closed-loop gains should not be selected when wider signal bandwidth is required. Decoupling capacitors should be placed close to the supply pins, unused amplifier channels should be configured in a stable non-inverting arrangement, and input and output paths should avoid excessive capacitive loading. This product record combines the manufacturer family information, package identification, electrical characteristics, lifecycle context, sourcing workflow, and practical guidance for evaluating the MC33174PG in a new quad-amplifier design. It also distinguishes the exact MC33174PG from package and ordering-code variations so engineers can confirm footprint compatibility before replacement.

RFQ İletişim
MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi
MC33178D

MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi

onsemi MC33178D is a low-power, low-noise dual operational amplifier designed for audio and data-signal processing applications. It is a monolithic bipolar amplifier using high-frequency PNP input transistors, an architecture selected to provide low input offset voltage, low noise, and low distortion. The device is offered in an 8-pin SOIC package and contains two amplifier circuits, allowing it to support common signal-conditioning tasks in compact analog designs. An operational amplifier is a voltage-amplifying component that uses negative feedback to create controlled gain, filtering, buffering, and signal-conditioning functions. The dual-amplifier configuration places two amplifiers in one package, reducing board area and simplifying designs that require two related channels. Within the broader semiconductor hierarchy, MC33178D belongs to the operational-amplifier family, which is part of the wider analog integrated-circuit and signal-processing categories. The MC33178/9 family combines bipolar transistor implementation with PNP input devices and an NPN output stage. This combination is particularly relevant to audio and general-purpose data processing because the input architecture is intended to reduce offset and distortion while maintaining a practical low-noise operating approach. Its dual-channel organization also makes the device applicable to small-signal amplification, filtering, buffering, and related analog front-end functions. The part can be used where two amplifier channels are needed at the same signal level or operating condition. Typical use cases include audio signal conditioning, low-level sensor amplification, active filtering, buffering, and general analog signal processing. The low-noise characteristic makes it relevant to designs in which the amplifier must preserve a small input signal without adding substantial unwanted noise, while the low-distortion architecture supports cleaner waveform reproduction. When designing around MC33178D, begin by confirming the required input common-mode range, output swing, gain-bandwidth behavior, input offset voltage, input bias current, and supply-current limits against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and sensitive-input routing should avoid nearby switching nodes and high-current return paths. This page combines the manufacturer family information with package, sourcing, comparison, and design guidance to support initial component evaluation and PCB planning. MC33178D is therefore suited to engineers seeking a compact, dual-channel, low-power bipolar op amp for audio or data-signal processing. Its strongest differentiators are the combined low-noise and low-distortion architecture, dual amplifier integration, and 8-pin SOIC implementation. Confirm the exact electrical limits and environmental ratings for the finished design before release to production.

RFQ İletişim
MC33178PG - Dual Low-Power Low-Noise Op Amp | onsemi
MC33178PG

MC33178PG - Dual Low-Power Low-Noise Op Amp | onsemi

The onsemi MC33178PG is a dual, bipolar operational amplifier packaged in an 8-pin PDIP. It operates from 2 V to 18 V, is intended for low-power industrial signal-processing applications, and offers a gain-bandwidth product of 5 MHz. The device uses high-frequency PNP input transistors to provide low input offset voltage, low noise, and low distortion. An operational amplifier is a high-gain analog signal-conditioning component used in instrumentation, audio, and data-processing circuits. It compares an input signal with a feedback reference to amplify voltage differences. Within the broader semiconductor hierarchy, the MC33178PG belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC families. The MC33178 family combines two amplifiers in one package, reducing board area for dual-channel designs. Its bipolar construction supports low-noise analog signal handling, while the PNP input stage is intended to improve offset voltage and distortion performance. The manufacturer identifies the family for quality audio and data-signal-processing applications. The MC33178PG operates from 2 V to 18 V, making it suitable for low-voltage industrial systems as well as conventional dual-supply analog circuits. A typical dual op-amp layout uses pins 1 and 7 as outputs, pins 2 and 6 as inverting inputs, pins 3 and 5 as non-inverting inputs, and pins 4 and 8 as the negative and positive supplies. Typical applications include audio preamplification, low-level sensor conditioning, active filtering, instrumentation, and general-purpose analog signal processing. When operating from a single supply, the input and output signal levels must remain within the input common-mode range and output swing limits specified by the manufacturer datasheet. For stable operation, follow the datasheet requirements for bypassing the positive supply and configure feedback so that the required noise gain and closed-loop bandwidth remain compatible with the intended signal path. Avoid placing input and output traces beside unrelated high-current switching nodes to reduce coupling. This page combines the manufacturer's device description with application-oriented guidance, pin organization, package information, and a conservative replacement comparison. It also identifies which drop-in alternatives have documented package compatibility and where final electrical verification remains necessary before a substitution is approved.

RFQ İletişim
MC33179PG - 5 MHz Quad Low-Power Op Amp | onsemi
MC33179PG

MC33179PG - 5 MHz Quad Low-Power Op Amp | onsemi

The onsemi MC33179PG is a quad, general-purpose operational amplifier designed for low-power audio and data-signal processing, with four amplifiers in a 14-pin DIP package. Its headline characteristics are a 5 MHz gain-bandwidth product, a 2 V to 18 V supply-voltage range, and a 14-PDIP through-hole package. The device is specified for industrial-temperature operation and combines bipolar input stages with a low-noise, low-power design intended for audio preamplification, active filtering, instrumentation, and general analog signal conditioning. An operational amplifier is an analog building block that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The MC33179PG belongs to the operational-amplifier hierarchy, where a general-purpose quad amplifier provides four independent amplifiers in one package. Placing four amplifiers in a single 14-pin DIP reduces component count and simplifies PCB assembly in designs that require several matched signal-conditioning channels. Key features include a 5 MHz gain-bandwidth product, a 2 V to 18 V operating supply range, and low-noise bipolar input characteristics. The quad configuration permits four independent amplifier sections with a shared positive and negative supply. This makes the MC33179PG appropriate for audio mixer stages, active low-pass and band-pass filters, sensor-conditioning circuits, and small-signal buffers. Its through-hole package also remains convenient for prototypes, educational designs, repair work, and manually assembled industrial control boards. The MC33179 family uses high-frequency PNP input transistors to obtain a combination of low noise and improved transient response compared with conventional bipolar amplifier inputs. This architecture is useful when a design must recover small signals cleanly while remaining within a modest power budget. Because the amplifiers share package leads for supply voltage, the board layout should treat the power pins as high-current nodes and provide a low-impedance return path to the decoupling capacitors. Typical applications include four-channel audio preamplification, active crossover and equalization networks, instrumentation amplifiers built from discrete sections, sensor signal conditioning, and general-purpose industrial control interfaces. The 14-pin DIP footprint is especially useful where through-hole assembly is preferred over fine-pitch surface-mount assembly. Designers should verify noise, offset, bias-current, output-swing, and stability requirements against the actual signal amplitude and source impedance. When laying out the MC33179PG, place the supply bypass capacitor close to pins 4 and 11 and route the ground return directly to the device ground pin. Keep feedback-loop components compact to minimize parasitic capacitance and oscillation risk, especially when the closed-loop gain is high. Decouple each signal source locally where practical so that input and output currents do not share long current paths on the board. This page consolidates the MC33179PG electrical identity, verified package and sourcing details, drop-in replacement analysis, and practical analog-layout guidance. It is intended to help engineers move quickly from device selection to schematic capture, PCB layout, and legacy-board redesign while remaining mindful of the part's through-hole package and amplifier-level trade-offs.

RFQ İletişim
MC33199D - ISO 9141 Automotive K-Line Interface | NXP
MC33199D

MC33199D - ISO 9141 Automotive K-Line Interface | NXP

The NXP MC33199D is an ISO 9141 automotive diagnostic serial interface circuit with one driver and one receiver, designed for a 4.5 V to 5.5 V supply and packaged in a 14-SOIC. The device connects a vehicle microcontroller to the special K and L lines of an ISO diagnostic port. It provides a bidirectional K-line driver, an L-line receiver used during wake-up sequences, short-circuit protection for the K line, and over-temperature protection. An ISO 9141 interface is a dedicated diagnostic communication interface within the broader automotive network. ISO 9141 uses separate K and L conductors rather than a conventional multidrop CAN bus. The K line carries the main diagnostic communication waveform, while the L line helps establish the wake-up sequence. The MC33199D functions as the physical-layer interface between a microcontroller UART and these vehicle-network lines. Key specifications include 1 driver and 1 receiver, a 4.5 V to 5.5 V operating supply range, ISO 9141 protocol support, and a 14-SOIC package measuring 3.90 mm wide. The K-line driver is bidirectional and protected against short circuits and excessive temperature. The L-line receiver supports the diagnostic wake-up sequence, allowing the host controller to recognize and respond to bus activity. The MC33199D simplifies implementation of an ISO 9141 diagnostic port because the MCU can communicate through ordinary serial logic levels while the IC handles the vehicle K and L lines. Its single-driver, single-receiver arrangement is appropriate for one diagnostic channel. Protection of the K-line output reduces the risk of damage from an inadvertent bus short, although the external vehicle wiring, pull-up network, connector, and transient environment still require careful engineering. Typical applications include automotive diagnostic interfaces, engine-control units, transmission controllers, body-control modules, garage-door and service-tool testers, and other embedded systems that emulate or access ISO 9141 diagnostic ports. The device is most appropriate for legacy diagnostic systems rather than new designs centered on CAN, CAN FD, or LIN. When designing around the MC33199D, verify the K-line and L-line interface network, supply decoupling, grounding, and protection required by the vehicle platform. The 5 V supply range excludes direct 3.3 V operation. Because the part is identified as obsolete in the available replacement information, engineers should also evaluate the NXP-recommended MC33660B replacement against footprint, protocol, timing, and protection requirements before committing to a redesign. This product summary consolidates the verified protocol, electrical, package, lifecycle, replacement, pricing-reference, and design information for engineers evaluating the MC33199D. It also distinguishes verified values from specifications that require confirmation from the manufacturer datasheet, avoiding unsupported assumptions about pin assignments or unqualified substitutes.

RFQ İletişim
MC33199DR2 - Automotive ISO 9141 Driver | NXP
MC33199DR2

MC33199DR2 - Automotive ISO 9141 Driver | NXP

NXP Semiconductors MC33199DR2 is an automotive ISO 9141 serial-link driver with one driver channel and no receiver channels, packaged in a 14-pin SOIC. It is designed for diagnostic systems in which a vehicle controller communicates with the K and L lines of an ISO diagnostic connector. The MC33199D family was developed for ISO 9141 diagnostic-interface requirements. An ISO 9141 serial-link driver is an interface circuit that connects a microcontroller or other diagnostic controller to a vehicle network. It belongs to the broader hierarchy of automotive interface ICs, serial transceiver ICs, interface ICs, and semiconductors. Its practical role is to translate controller-level logic signals into electrical signaling suitable for the physical diagnostic bus while providing the electrical characteristics required by the ISO 9141 application. The principal identified feature is the MC33199D's 1-driver/0-receiver arrangement. This focused architecture is appropriate when the surrounding diagnostic electronics perform receive functions elsewhere and the MCU requires a dedicated ISO 9141 line driver. Its 14-SOIC package provides a conventional surface-mount interface that can be assembled using standard automotive PCB practices. The DR2 ordering suffix identifies the manufacturer's specified packaging configuration. The device is intended for automotive diagnostic communication rather than general-purpose RS-232, RS-485, or CAN signal conditioning. It should be selected when the system architecture requires an ISO 9141 K-line or L-line interface between a vehicle controller and an external diagnostic connector. Designers must still confirm voltage levels, bus topology, external network components, protection requirements, and timing against the relevant vehicle diagnostic standard before releasing the design. Typical applications include automotive diagnostic connectors, engine-control test equipment, vehicle communication modules, garage-test equipment, and service-bus analyzers. These systems often combine an MCU, an ISO 9141 physical-layer driver, connector protection, and diagnostic software. MC33199DR2 is useful when the diagnostic interface is specifically based on ISO 9141 rather than a higher-bandwidth CAN or LIN network. The principal design consideration is interface compatibility. Confirm that the selected MCU output levels, timing, and K-line or L-line wiring match the MC33199D requirements. Because an automotive diagnostic port connects to external equipment and vehicle wiring, validate transient immunity, fault behavior, grounding, and protection at the connector rather than treating the IC as the only safeguard. This product page combines the exact MC33199DR2 ordering information, package identity, documented interface role, sourcing links, and engineering-oriented selection guidance. It also distinguishes verified drop-in candidates from merely similar interface ICs, helping engineers avoid choosing a functionally related transceiver that cannot replace the original footprint.

RFQ İletişim
MC33201D - 12V Rail-to-Rail Operational Amplifier | onsemi
MC33201D

MC33201D - 12V Rail-to-Rail Operational Amplifier | onsemi

The onsemi MC33201D is a single-circuit, low-voltage, rail-to-rail input and output operational amplifier packaged in an 8-pin SOIC. It operates from a maximum 12 V supply, accepts input voltages up to 200 mV beyond either supply rail without output phase reversal, and produces an output that can swing to within 50 mV of each rail. These characteristics allow analog signals to use nearly the complete supply-voltage range. A rail-to-rail operational amplifier is an analog signal-conditioning amplifier whose input common-mode range and output voltage range extend close to the positive and negative supply rails. In the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. It can amplify sensor signals, buffer high-impedance sources, compare voltages, or integrate feedback networks around a single analog signal path. The MC33201D combines rail-to-rail input operation with low-noise, high-output-drive characteristics. Its input stage accepts common-mode signals beyond the nominal supply rails by as much as 200 mV without reversing the output polarity. Its output stage can approach each supply rail within 50 mV, improving usable output swing in low-voltage systems where conventional fixed-range amplifiers leave little headroom. The device is designed for low-voltage analog systems in which common-mode and output range are more important than using a larger, higher-voltage amplifier. Rail-to-rail behavior is particularly useful when a sensor output can move close to a low supply rail, when an ADC or DAC must be driven near the end of its input range, or when a bipolar signal must be handled with a single positive supply. The manufacturer documentation identifies the MC33201, MC33202, MC33204, NCV33201, NCV33202, and NCV33204 as members of the same operational-amplifier family. Typical uses include portable instrumentation, sensor interfaces, low-voltage audio paths, ADC input conditioning, current monitoring, and general-purpose signal amplification. In each case, the designer should verify input bias current, offset voltage, bandwidth, output-current capability, noise, stability, and operating-temperature limits against the manufacturer datasheet before fixing the circuit. The most important design consideration is to preserve the amplifier's stability and rail-to-rail performance. Keep feedback components close to the device, avoid excessive capacitive loading on the output, and account for common-mode behavior in the region where the input stage transitions between internal transistors. Decoupling capacitors should be connected directly between each supply pin and the appropriate ground reference. This product record combines the manufacturer family information with package, function, commercial, comparison, and application guidance. It also identifies same-footprint family options for designs that can tolerate their different input-offset characteristics, while making clear that final substitution requires electrical verification in the target circuit.

RFQ İletişim
MC33201PG - 2.2MHz Rail-to-Rail Op Amp | onsemi | DIP-8
MC33201PG

MC33201PG - 2.2MHz Rail-to-Rail Op Amp | onsemi | DIP-8

The onsemi MC33201PG is a single-amplifier, low-voltage rail-to-rail operational amplifier with a 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, and a 1.8 V to 12 V supply range in an 8-pin plastic DIP package. Designed for general-purpose signal conditioning, the device combines rail-to-rail input and output operation with operation over a -40°C to +105°C temperature range. An operational amplifier, or op amp, is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog semiconductors, the MC33201PG belongs to the voltage-feedback operational-amplifier family and provides a practical combination of low supply voltage, moderate bandwidth, and wide input and output swing. It is suitable for systems that need useful signal amplification without requiring the noise, offset, or power characteristics of a precision amplifier. The rail-to-rail input stage can accept signals as much as 200 mV beyond the supply rails without phase reversal at the output. Rail-to-rail output operation allows the output voltage to approach both supply rails, with the output swinging within approximately 50 mV of each rail. These characteristics make the amplifier useful in low-voltage sensor interfaces, battery-powered instrumentation, and control systems where available signal range is limited by the supply voltage. With a 2.2 MHz gain-bandwidth product and 1 V/µs slew rate, the MC33201PG is intended for general-purpose signal processing rather than high-speed video or precision measurement. Its single-amplifier configuration reduces board requirements where only one signal path is needed, while the 8-pin DIP format supports through-hole assembly, prototyping, educational platforms, and repair of legacy equipment. Typical applications include low-voltage sensor buffering, portable measurement systems, audio preamplifier stages, motor and actuator control interfaces, and general feedback networks. The 1.8 V minimum supply supports modern low-voltage systems, while the 12 V maximum provides flexibility across industrial and consumer rails. The -40°C to +105°C operating range also supports industrial temperature requirements when other system parameters, such as offset and bias current, are acceptable. PCB layout should keep feedback traces short, connect decoupling capacitors close to the supply pins, and route sensitive input nodes away from switching-current paths. Because a DIP package provides generous lead spacing, it is mechanically convenient for prototyping, but through-hole devices occupy more board area than comparable surface-mount packages. Engineers upgrading an existing MC33201PG design should preserve the established pin connections and account for the device's finite input and output swing limits. This product page combines the manufacturer's electrical characteristics with engineering-oriented application guidance, pin information, comparison criteria, and practical layout considerations. It is intended to help designers evaluate the MC33201PG for low-voltage general-purpose amplification without confusing rail-to-rail capability with precision or high-speed performance.

RFQ İletişim
MC33201VD - 2.2MHz Rail-to-Rail Op Amp | onsemi | SOIC-8
MC33201VD

MC33201VD - 2.2MHz Rail-to-Rail Op Amp | onsemi | SOIC-8

onsemi MC33201VD is a single-circuit, general-purpose rail-to-rail operational amplifier with a 1.8 V to 12 V supply range, 2.2 MHz gain-bandwidth product, and 1 V/µs slew rate, housed in an 8-pin SOIC package. Its input stage can operate 200 mV beyond either supply rail without output phase reversal, while the output can swing to within 50 mV of the rails. A rail-to-rail operational amplifier is an analog amplifier whose input and output voltage ranges extend close to the positive and negative supply rails. It belongs to the operational amplifier hierarchy within analog and signal-processing ICs, making it useful when a low-voltage system cannot support conventional amplifiers whose inputs and outputs remain farther from the supply limits. The MC33201 family is designed to preserve usable signal range in compact, single-supply equipment. The principal operating characteristics include a 1.8 V to 12 V supply-voltage range, 2.2 MHz gain-bandwidth product, and 1 V/µs slew rate. Rail-to-rail input and output operation allows more of the available supply voltage to be used for signal conditioning. The input can be driven 200 mV beyond the supply rails without phase reversal, helping the amplifier tolerate overdrive near the rail limits. Output swing is specified to remain within 50 mV of each rail under the stated conditions. The MC33201 is a single amplifier with one noninverting input, one inverting input, and one output. Its 8-pin SOIC package provides a conventional small-surface-mount implementation for analog boards. The combination of low minimum supply voltage, broad rail-to-rail coverage, and moderate bandwidth supports general-purpose amplification, current-voltage conversion, sensor conditioning, and filtering. These characteristics make it more appropriate for low-to-moderate frequency precision analog stages than for high-speed signal chains. Typical applications include portable sensor interfaces, battery-powered instrumentation, low-voltage control systems, transducer signal conditioning, and audio input stages. The amplifier can operate from a 1.8 V supply, which is useful for energy-efficient systems with limited rail headroom. Its 2.2 MHz gain-bandwidth product allows moderate closed-loop bandwidth at practical gains, while the 1 V/µs slew rate supports responsive changes to waveforms within that bandwidth limit. The principal design tradeoff is the relationship between bandwidth, supply voltage, output load, and stability. Place the device close to the feedback network and supply bypass components, keep feedback traces short, and verify the configuration against the manufacturer’s recommended compensation methods. The VD ordering code is associated with an 8-pin SOIC package, but production-temperature, tape-and-reel, and orderable-package details should be confirmed against the current onsemi product record before release. This page organizes the MC33201VD operating envelope, verified alternatives, package and pin information, cross-reference comparisons, and practical application guidance. It also distinguishes electrical limits from package-ordering details so engineers can assess board compatibility, bandwidth, supply headroom, and thermal or sourcing constraints before selecting the amplifier.

RFQ İletişim
MC33202D - Dual Rail-to-Rail Op Amp | onsemi
MC33202D

MC33202D - Dual Rail-to-Rail Op Amp | onsemi

The onsemi MC33202D is a dual rail-to-rail operational amplifier designed for low-voltage operation from 1.8 V to 12 V, supplied in an 8-pin SOIC package. The MC33202D contains two amplifier channels, supports rail-to-rail operation at both the input and output stages, and is specified for an ambient temperature range of -40°C to +105°C. These characteristics position it for compact, low-voltage signal-conditioning systems requiring one package to implement two analog channels. An operational amplifier is an analog integrated circuit that compares an input signal with a feedback-defined reference and amplifies the difference between them. In the broader hierarchy, the MC33202D belongs to the operational-amplifier class, then to the amplifier-IC category, and ultimately to the semiconductor and signal-processing markets. Rail-to-rail input operation allows the input common-mode range to extend toward the supply rails, while rail-to-rail output operation improves dynamic range when the output must approach either supply limit. The primary headline features are the 1.8 V to 12 V supply range, dual-channel configuration, and rail-to-rail input and output capability. The 8-pin SOIC package provides a conventional surface-mount footprint suitable for standard PCB assembly methods. Its -40°C to +105°C temperature range makes it relevant to industrial, instrumentation, communications, and consumer applications that require operation across an extended temperature span. MC33202D belongs to the MC33201/MC33202/MC33204 family of low-voltage, rail-to-rail operational amplifiers. The family architecture is intended for low-voltage analog systems in which signal levels may occupy much of the available supply range. Because the device is supplied in a dual amplifier configuration, a complete two-channel circuit can be implemented without selecting two separate single-channel packages, reducing board area and simplifying component procurement. Typical applications include sensor-signal conditioning, low-voltage audio and communications paths, transducer amplification, general-purpose voltage amplification, and dual-channel filtering or feedback networks. For instrumentation applications, the rail-to-rail input characteristic can reduce the need for additional mid-supply biasing when signals vary over a broad range. In communications systems, the low operating voltage can simplify compatibility with modern low-voltage supply rails. Design the surrounding decoupling, input common-mode range, output load, and stability network carefully. Place the power-bypass capacitor close to the supply pins, maintain the device within its specified supply-voltage and temperature limits, and verify the intended feedback topology across the required signal bandwidth. The manufacturer datasheet should be used as the controlling reference for electrical characteristics, limit values, and test conditions. This page organizes the MC33202D datasheet information, pin-compatible replacement candidates, package details, and engineering guidance in a form that helps designers evaluate the amplifier, compare drop-in options, and plan an 8-pin SOIC implementation without relying on generic amplifier-selection advice.

RFQ İletişim
MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi
MC33202PG

MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi

onsemi MC33202PG is a dual, low-voltage, rail-to-rail input and output operational amplifier with a 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, and a 1.8 V to 12 V supply range in an 8-pin PDIP package. The device supports industrial-temperature operation from -40 °C to 105 °C and provides two amplifier circuits in one package. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The MC33202PG belongs to the rail-to-rail operational-amplifier family, combining input and output common-mode capability with low-voltage operation. This places it within the broader hierarchy of analog ICs, signal-conditioning ICs, amplifiers, and general-purpose operational amplifiers. Rail-to-rail input operation allows the input voltage to approach either supply rail. According to the onsemi datasheet, inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal in the outputs. Rail-to-rail output operation allows each output to swing within approximately 50 mV of its corresponding rail, improving output range utilization in low-voltage systems. The MC33202PG combines a 2.2 MHz gain-bandwidth product with a 1 V/µs slew rate. These values make it suitable for general-purpose signal amplification, low-voltage analog interfaces, and feedback-control circuits where operating from a single 1.8 V supply is useful. Its dual configuration can reduce board area when two independent amplifier channels are required. Typical uses include sensor-interface amplification, audio and communication signal conditioning, voltage buffering, active filtering, and industrial control-system analog sections. The 1.8 V minimum supply supports portable and embedded systems, while the -40 °C to 105 °C temperature range supports industrial environments when the complete system is qualified for the intended conditions. Designers should verify input and output limits under the selected supply voltage and load current. Input and output stability should be evaluated with the actual source impedance, feedback network, load, and bypass capacitance. Because this is a through-hole PDIP device, its larger footprint must be considered when replacing it with surface-mount alternatives. This product summary combines the MC33202PG electrical ratings, package information, pin assignment, practical application guidance, and qualified same-footprint replacement information. The alternatives are restricted to devices presented as pin-to-pin compatible rather than merely similar amplifiers, helping engineers identify a practical migration path without implying electrical identity.

RFQ İletişim
MC33202VD - Dual Rail-to-Rail Op Amp | onsemi | 8-SOIC
MC33202VD

MC33202VD - Dual Rail-to-Rail Op Amp | onsemi | 8-SOIC

The onsemi MC33202VD is a dual, general-purpose operational amplifier with rail-to-rail input and output operation, a 1.8 V to 12 V supply range, and an 8-pin SOIC package. According to the onsemi MC33202 family description, each input may be driven as far as 200 mV beyond the supply rails without phase reversal at the output, while the output can swing within 50 mV of either rail. The device is intended for low-voltage, low-power signal-conditioning systems that need broad input and output voltage coverage. An operational amplifier, commonly called an op amp, is a high-gain analog building block used in amplifier, comparator, buffer, filtering, and feedback-control circuits. The MC33202 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability broadens the usable signal range in low-voltage systems. Two amplifiers are integrated into each package, allowing compact designs with two independent analog channels. The principal features are dual-channel construction, input common-mode operation beyond the supply rails, near-rail output swing, and operation from 1.8 V to 12 V. Input overdrive tolerance of 200 mV is particularly useful in sensor, filter, and feedback applications where signals may briefly approach or cross a rail. The 50 mV output-swing specification also allows a large portion of the available supply voltage to be used by downstream circuitry. The MC33202 family is designed for very low supply voltages, making rail-to-rail behavior more relevant than the input and output ranges of conventional non-rail-to-rail amplifiers. The family provides rail-to-rail operation at both inputs and outputs. This architecture supports signal amplification when the input is close to either supply rail and improves output headroom when driving the next stage near the positive or negative limit. Typical applications include low-voltage sensor interfaces, battery-powered analog measurement, audio signal conditioning, active filtering, instrumentation, and general-purpose dual-amplifier modules. Two channels can be used for instrumentation-amplifier input stages, active filters, differential signal conditioning, or separate gain and buffer functions when the circuit operates within the device's common-mode and output limits. PCB design should prioritize short analog input paths, clean grounding, and stable supply bypassing. Place the input and output resistors close to their associated amplifier pins, route high-impedance sensor nodes away from switching nodes, and decouple the supply connection near the package. Because rail-to-rail input stages commonly use internal crossover transitions, input bias-current and offset behavior should be evaluated over the complete signal range rather than only near mid-supply. This page combines the manufacturer family characteristics, package information, sourcing guidance, practical design considerations, and pin-compatible replacement options. It also identifies where channel-level electrical data should be confirmed in the manufacturer datasheet before a production design or PCB release.

RFQ İletişim
MC33204P - Quad Rail-to-Rail 1.8V Op Amp | onsemi
MC33204P

MC33204P - Quad Rail-to-Rail 1.8V Op Amp | onsemi

onsemi MC33204P is a four-circuit rail-to-rail operational amplifier designed for low-voltage signal conditioning and general-purpose analog systems. It operates from 1.8 V to 12 V and is packaged in a 14-pin plastic dual in-line package. The quad configuration provides four amplifiers in one device, reducing board area and simplifying designs that require several matched low-voltage signal stages. Rail-to-rail input and output operation allows the amplifier to use most of the available supply voltage. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify small voltage differences between its inputs. The MC33204P belongs to the MC33201/MC33202/MC33204 family of low-voltage rail-to-rail amplifiers. Its differential input stage supports input voltages that may extend beyond the supply rails, while the output stage can approach both rails. This makes it useful where signal levels occupy a significant portion of the supply range. According to the onsemi product page, inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mV of each rail. These figures are particularly useful when designing from a 1.8 V or 3.3 V rail. The four-amplifier arrangement supports independent gain stages, sensor interfaces, filters, comparators, and active feedback networks without requiring four separate packages. The common-mode input range is a defining feature of this amplifier family. Rail-to-rail input behavior lets a sensor output remain in the usable input range even when it approaches a supply rail. Output swing close to the rails increases the available dynamic range and can reduce the need for an additional output-biasing stage. Designers must still verify signal levels, output-load conditions, stability, and gain bandwidth for the selected operating point. Typical uses include portable sensor interfaces, industrial control and instrumentation, battery-powered monitoring, low-voltage data acquisition, active filters, and general analog signal conditioning. The quad package is particularly suitable when four similar amplifier functions are required. It can also support mixed functions, such as one buffer, two gain stages, and one comparator, although each channel's loading and stability requirements should be evaluated independently. For layout, route input and feedback connections away from output and supply paths to reduce coupling. Place bypassing capacitors close to the supply pins and maintain the feedback network close to the amplifier. Confirm the gain-bandwidth product and stability requirements for the intended closed-loop gain, especially when driving capacitive loads or operating with long PCB traces. This page combines the manufacturer specifications, package information, cross-reference findings, application guidance, and engineering trade-offs needed to evaluate the MC33204P for a new analog design. It also highlights where the quad pin-compatible LM348 may be considered and where its rail-to-rail performance must be checked before substitution.

RFQ İletişim
MC33204PG - Quad Rail-to-Rail Op Amp | onsemi
MC33204PG

MC33204PG - Quad Rail-to-Rail Op Amp | onsemi

The onsemi MC33204PG is a quad general-purpose operational amplifier with rail-to-rail input and output operation in a 14-pin PDIP package. It provides four amplifiers per device, a 2.2 MHz gain-bandwidth product, and a 1 V/us slew rate. The MC33204 operates from 1.8 V to 12 V, making it suitable for low-voltage battery-powered, industrial control, sensor-conditioning, and general signal-processing systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. A rail-to-rail input amplifier accepts common-mode input voltages close to the positive and negative supply rails, while a rail-to-rail output amplifier can swing its output close to those rails. This expands the usable input and output range compared with conventional fixed-range amplifiers, especially when the supply voltage is only a few volts above the signal amplitude. The MC33204 family combines four amplifiers in one package, reducing board area and simplifying multi-channel designs where identical amplifier performance is useful. Its inputs may be driven approximately 200 mV beyond the supply rails without phase reversal at the outputs. The output can swing to within approximately 50 mV of either rail. A gain-bandwidth product of 2.2 MHz supports signal bandwidths suitable for audio, instrumentation, filtering, and feedback-control circuits. The 1 V/us slew rate provides practical full-power-bandwidth capability for low- and mid-frequency analog signals. The device is intended for general-purpose amplification rather than high-speed precision applications, so input offset voltage, input bias current, noise density, and stability characteristics should be reviewed against the precision required by each circuit. Decoupling capacitors should be placed close to the supply pins to control impedance in feedback networks and prevent oscillation. Typical uses include low-voltage sensor interfaces, current-to-voltage conversion, active filtering, audio summing stages, joystick and touch inputs, and general instrumentation. Because the MC33204PG contains four matched-function amplifiers in one PDIP package, it is especially useful where a design needs several channels of similar gain, bandwidth, and output-drive capability. When designing with the MC33204, verify that the signal and output ranges remain within the rail limits at the lowest operating supply voltage. Check the required common-mode range for sensor outputs and confirm that capacitive loads connected to the output remain inside the stable operating region. Use the pin-description table in the onsemi MC33204 datasheet when assigning PCB tracks. This page combines the manufacturer product information with ordering details, drop-in replacement analysis, application guidance, and practical design notes. It helps engineers evaluate the MC33204PG for low-voltage analog signal chains while keeping package, sourcing, and circuit-integration considerations in one place.

RFQ İletişim
MC33215BE - Voice-Switched Speakerphone IC | NXP
MC33215BE

MC33215BE - Voice-Switched Speakerphone IC | NXP

The NXP Semiconductors MC33215BE is a voice-switched speakerphone circuit, also identified as a telecom interface IC, in a 42-pin shrink dual inline package. The device integrates one voice-switched speakerphone circuit and is intended for telephone, intercom, and voice-communication equipment requiring local voice switching and speakerphone operation. Its specified operating temperature range is -20°C to 70°C. A speakerphone circuit is a voice-processing and interface category that connects a telephone or communications line to a microphone, loudspeaker, and related analog voice circuitry. Within the system hierarchy, the MC33215BE is a telecom interface IC, a type of integrated circuit used to translate and control analog voice signals between line and audio endpoints. Its 42-pin package provides the external connections needed for power, line interface, microphone, speaker, control, and signal-conditioning networks. The MC33215BE consolidates one complete voice-switched speakerphone function into a single IC rather than requiring several separate switching and interface blocks. This integration can simplify a telephone-terminal layout while reducing the number of separate active devices required for voice-path control. Designers should still use the manufacturer datasheet when assigning external networks, signal levels, supply limits, and control behavior to individual pins. The 42-pin shrink DIP package is suited to through-hole assembly and makes the MC33215BE attractive for legacy telephone equipment, handsets, intercom stations, and voice-terminal products assembled by insertion rather than surface-mount automation. Its package dimensions and lead spacing must match the board footprint, while adequate clearance should be maintained around neighboring analog components to reduce noise coupling and accidental soldering bridges. Typical applications include analog telephones, speakerphone terminals, intercom equipment, voice messaging appliances, and compact telephone-answering accessories. The device is also relevant to industrial voice panels and communications equipment that operates from -20°C to 70°C and needs a dedicated circuit for switching between microphone and loudspeaker voice paths. System-level EMC, line-interface protection, and audio feedback control remain separate design responsibilities. When designing around the MC33215BE, identify every external component by its datasheet reference and verify the selected package orientation before layout release. Do not infer pin functions from neighboring devices or generic telecom interfaces. Review the manufacturer application circuit for recommended coupling, filtering, and grounding arrangements, then verify the complete analog path on the assembled board. This page consolidates the confirmed device identity, package, temperature range, and circuit count with application guidance, sourcing answers, and engineering notes. It also clearly distinguishes confirmed manufacturer-facing information from parameters that must be obtained from the MC33215BE datasheet before schematic capture or production release.

RFQ İletişim
MC33272AP - Dual 24 MHz Low-Offset Op Amp | onsemi
MC33272AP

MC33272AP - Dual 24 MHz Low-Offset Op Amp | onsemi

onsemi MC33272AP is a dual, general-purpose operational amplifier with a 24 MHz gain-bandwidth product, 10 V/µs slew rate, and low input-offset voltage, housed in an 8-pin plastic DIP package. It operates from 3 V to 36 V and uses bipolar input circuitry with Zip-R-Trim offset adjustment. The two amplifiers in the package are independently usable in conventional inverting, non-inverting, differential, active-filter, and instrumentation circuits. An operational amplifier is a voltage-controlled differential amplifier whose inverting and non-inverting inputs are compared to produce an amplified output. Within the amplifier hierarchy, the MC33272AP belongs to the bipolar operational-amplifier family and provides a general-purpose combination of precision input characteristics, wide bandwidth, and high slew rate. It is a voltage-feedback device suitable for signal conditioning, feedback control, analog signal processing, and test equipment. The primary performance features include a 24 MHz gain-bandwidth product, 10 V/µs slew rate, and low input-offset voltage. These characteristics allow the device to handle signals extending well beyond audio-band requirements while retaining the low-offset behavior sought in instrumentation and feedback applications. Wide operating-voltage support also permits use in industrial systems operating from 3 V through 36 V, subject to the absolute maximum ratings and common-mode limitations specified by the manufacturer. The bipolar input architecture and patented Zip-R-Trim element distinguish the MC33272 from simpler general-purpose amplifiers. Input-offset adjustment improves matching between closely related amplifier channels, which is useful in differential measurement paths where offset error can otherwise become a significant part of the total error budget. The dual-doublet frequency-compensation architecture supports stable operation in typical feedback networks without requiring the precision associated with more specialized instrumentation amplifiers. Typical uses include low-level sensor conditioning, current-loop receivers, active filters, audio and communication-signal stages, sample-and-hold buffers, and laboratory control circuits. The 10 V/µs slew rate is particularly useful for waveform and pulse paths, while the 24 MHz bandwidth allows the amplifier to operate effectively above audio frequencies. In closed-loop designs, actual bandwidth depends on the selected noise gain, feedback network, load, and device stability requirements. When designing an MC33272AP circuit, verify common-mode input range, output swing, output-current capability, and noise-gain stability against the manufacturer datasheet for the actual supply voltage. Keep feedback traces short, place compensation or decoupling components close to the relevant pins, and avoid loading the output beyond its specified limits. Input-bias-current errors and resistor-generated noise should also be included in the overall accuracy calculation. This page combines manufacturer specifications, package details, drop-in alternatives, application guidance, and parameter-by-parameter engineering comparisons. It is structured to help engineers identify the appropriate replacement, plan the PCB footprint, and evaluate whether the 24 MHz bandwidth and 10 V/µs slew rate meet the requirements of a particular analog signal chain.

RFQ İletişim
MC33290D - ISO 9141 K-Line Serial Link Interface | NXP
MC33290D

MC33290D - ISO 9141 K-Line Serial Link Interface | NXP

The NXP (formerly Freescale) MC33290D is an ISO 9141 K-Line serial link bus interface IC housed in an 8-pin SOIC package, designed for bidirectional half-duplex communication between a vehicle's on-board microcontroller and off-board diagnostic equipment. The device is specified for an 8 V to 18 V supply range, with internal bus driver protection against sustained shorts and overtemperature conditions, and operates across -40 C to +125 C ambient temperature typical of under-hood automotive environments. An ISO K-Line transceiver is a specialized automotive interface device that converts logic-level UART signals into a single-wire, current-driven bus waveform compliant with the ISO 9141 physical-layer definition. Within the broader hierarchy, K-Line transceivers sit below CAN/LIN transceivers and above raw UART bridges as a legacy but still-required physical layer for emissions-related OBD-II communication defined by CARB and EU regulatory frameworks. Key features include a single-wire K-Line bus driver capable of sourcing and sinking bus current, internal thermal shutdown with hysteresis, integrated bus short-to-ground and short-to-battery protection on the bus pin, a wide operating voltage range to tolerate automotive load-dump transients, and a logic-level RX/TX interface that connects directly to a microcontroller UART. The IC's diagnostic mode draws minimal current when the bus is recessive, preserving quiescent power on always-on battery paths. Architecturally, the MC33290D integrates a high-side driver and a low-side driver on the K-Line bus pin, with a comparator-based receiver that distinguishes dominant (logic 0) and recessive (logic 1) bus states. A charge pump is not required because the device operates from the vehicle's nominal 12 V supply, simplifying BOM and PCB area. Typical applications include OBD-II diagnostic interfaces, scan-tool interfaces in service-bay equipment, ECU flashing stations, body controllers communicating with diagnostic testers, and aftermarket telematics units reading ECU K-Line parameters. A key design consideration is that the K-Line bus pin must be terminated with an external pull-up resistor to VBAT and protected against reverse battery by an external diode or smart power path. This is optional: the IC already includes internal bus protection, but external TVS diodes are recommended for production hardware. This page consolidates distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet to accelerate part selection for automotive diagnostic designs.

RFQ İletişim