Ürünler (44.000+)

MC3303PG - Quad 1 MHz Operational Amplifier | onsemi | 14-PDIP
MC3303PG

MC3303PG - Quad 1 MHz Operational Amplifier | onsemi | 14-PDIP

The onsemi MC3303PG is a four-channel general-purpose operational amplifier designed for single-supply operation, with a 3 V to 36 V supply range, true differential inputs, internal frequency compensation, and short-circuit protection. The device is packaged in a 14-pin through-hole DIP and is intended for low-cost analog signal conditioning, instrumentation, and general-purpose amplifier applications. Its unity-gain bandwidth is 1 MHz, while the specified minimum common-mode rejection ratio is 70 dB and the listed input offset voltage is 10 mV. An operational amplifier is an analog building block that compares two input voltages and amplifies their difference. The quad MC3303PG contains four amplifier sections in one package, allowing a circuit to perform multiple amplification, buffering, summing, or comparison functions while reducing board area. MC3303PG belongs to the operational-amplifier hierarchy within analog ICs and integrated circuits, and its true differential input architecture supports accurate sensing of small signals referenced to either ground or another bias point. The principal features include four amplifier channels, a 1 MHz gain-bandwidth product, operation from a single positive supply, Class AB output stages, true differential inputs, and low input bias current. Internal frequency compensation removes the need for external compensation networks in unity-gain applications. These characteristics make the MC3303PG practical for general-purpose designs where simplicity, tolerance of a wide supply range, and moderate operating bandwidth are more important than rail-to-rail output swing or very low offset voltage. MC3303PG is electrically similar to the widely used MC1741C-family architecture but adds advantages for single-supply operation. True differential inputs allow the amplifier to operate without artificial ground bias around the input signal. The four-channel arrangement supports signal amplifiers, active filters, transducers, sensor interfaces, audio preamplification, and industrial control modules. A wide 3 V to 36 V operating range also permits operation from both compact low-voltage systems and higher industrial supply rails. Typical uses include low-frequency sensor conditioning, audio input stages, active-filter sections, comparator-style threshold circuits, and general instrumentation. Because the amplifier is not rail-to-rail, input and output common-mode limits must be respected in low-voltage designs. For battery-powered equipment, verify input bias current and supply-current requirements against the system power budget. The DIP package also requires adequate through-hole spacing and mechanical clearance from adjacent heat-producing components. When designing around MC3303PG, begin with the manufacturer pin-description and electrical-characteristics tables, especially for input common-mode range, output swing, supply current, and stability. Place bypass capacitors close to the supply pins and route feedback components to minimize parasitic capacitance. Avoid operating the output near either supply rail unless the selected output-load condition remains within the specified swing range. This product page consolidates the manufacturer product information, distributor identification, package details, and practical engineering guidance for the MC3303PG. It also distinguishes the verified 14-pin DIP replacement candidates from broader functional equivalents so that PCB-level drop-in decisions are made with package and parameter checks rather than by device category alone.

RFQ İletişim
MC3303PT - Quad 1 MHz Low-Power Op Amp | STMicroelectronics
MC3303PT

MC3303PT - Quad 1 MHz Low-Power Op Amp | STMicroelectronics

The STMicroelectronics MC3303PT is a four-circuit, low-power bipolar operational amplifier with a 1 MHz gain-bandwidth product, a maximum supply voltage of 36 V, and a 14-pin TSSOP package. It is designed for general-purpose instrumentation, buffer, and amplifier applications that require four amplifiers in one package. The integrated quad arrangement reduces component count and simplifies PCB layout compared with four individual single amplifiers. An operational amplifier is a voltage-amplifying semiconductor in the amplifier IC category. It compares an input voltage with a feedback-defined reference voltage and drives its output to reduce the difference between them. The MC3303PT belongs to the broader low-power operational-amplifier family and provides four internally compensated amplifiers with true differential inputs in one package. The MC3303PT supports single-supply operation up to 36 V and dual-supply operation up to ±18 V. Its maximum input-bias current is 500 nA, which helps limit the current required from high-impedance signal sources. The device also provides short-circuit-protected outputs, an internally compensated Class AB output stage, and electrical characteristics described as similar to the widely used UA741. Each amplifier channel is internally compensated, allowing operation as a closed-loop amplifier without external compensation components. The Class AB output stage is intended to provide low crossover distortion while avoiding the continuous conduction characteristic of a purely class A output stage. The quad package is useful when four channels can share the same supply rails and ground reference. Typical applications include low-frequency instrumentation amplifiers, signal buffers, active filters, transducer interfaces, sensor signal conditioning, and general analog signal-processing chains. The 1 MHz gain-bandwidth product is suitable for moderate-bandwidth closed-loop stages rather than high-speed video or RF amplification. For new designs, verify the input common-mode range, output swing, input-offset voltage, input-bias current, and output-current capability in the manufacturer datasheet against the actual signal range. Decoupling capacitors should be placed close to the supply pins, and each unused amplifier channel should be configured according to the manufacturer's recommended stable-input arrangement rather than left floating. This product page organizes the confirmed MC3303PT characteristics, package information, application guidance, and sourcing path into an engineering-focused reference. It also distinguishes verified device attributes from parameters that require confirmation from the complete manufacturer datasheet before layout, simulation, or production release.

RFQ İletişim
MC3303PW - 30V 1MHz Quad Op Amp | Texas Instruments
MC3303PW

MC3303PW - 30V 1MHz Quad Op Amp | Texas Instruments

The Texas Instruments MC3303PW is a quad, general-purpose operational amplifier with a 30 V maximum supply rating, 1 MHz gain-bandwidth product, and four amplifiers in a 14-pin TSSOP package. It operates from single or dual supplies across a 3 V to 36 V total supply range, making it suitable for industrial control, instrumentation, sensor conditioning, and audio signal-chain designs. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The MC3303 belongs to the linear amplifier hierarchy, where four independent amplifiers share one package. Each channel combines a true differential input stage, a Class AB output stage, internal frequency compensation, and short-circuit protection. These features simplify circuit design because external compensation networks are not required for typical closed-loop amplifier configurations. The MC3303's principal operating characteristics include a 1 MHz gain-bandwidth product, support for supply voltages from 3 V to 36 V, and an operating temperature range from -40 °C to 85 °C. Its low-power design is intended for general-purpose analog systems where four amplifier channels, compact packaging, and flexible supply operation are more important than rail-to-rail input or output capability. Input common-mode and output swing limits must be checked against the actual supply voltage before the circuit is finalized. The true differential input stage supports common-mode input operation while reducing output offset resulting from common input signals. A Class AB output stage supports bidirectional output current without the crossover distortion associated with complementary Class B stages. Internal frequency compensation makes the device convenient for unity-gain voltage followers, amplifiers, comparators, and basic active-filter blocks, although the stable operating range and output-drive requirements depend on the selected closed-loop gain. Typical uses include four-channel sensor amplification, industrial transducer interfaces, low-frequency audio mixing, buffered instrumentation, active filtering, and general voltage amplification. The 14-pin TSSOP package reduces board area compared with a larger through-hole package, while its exposed thermal behavior and power dissipation should be considered when all four channels operate continuously at high output voltage and current. For stable operation, place input and feedback components close to the relevant pins, route return currents directly to the ground connection, and avoid long high-impedance traces near the amplifier inputs. Use the manufacturer pin-description table to assign the four amplifier sections and power pins. Check input range, output swing, load current, supply headroom, and thermal rise together. This page also organizes pin compatibility, selection trade-offs, application guidance, and design checks into one engineering-focused reference.

RFQ İletişim
MC33071D - 44V Single-Supply Op Amp, 4.5MHz GBW | onsemi
MC33071D

MC33071D - 44V Single-Supply Op Amp, 4.5MHz GBW | onsemi

The onsemi MC33071D is a single-supply operational amplifier with a 3.0 V to 44 V operating supply range, a 4.5 MHz gain-bandwidth product and a 13 V/µs slew rate, housed in an 8-pin SOIC-8 surface-mount package. It is a single amplifier in the MC33071/72/74 and MC34071/72/74 family, so a dual or quad version is available when more channels are needed on the same board. An operational amplifier, or op amp, is a high-gain differential amplifier whose inverting and non-inverting inputs are compared and whose output is driven to correct the difference between them. In the product-type hierarchy, an op amp belongs to the amplifier IC class, then to analog integrated circuits, then to the wider semiconductor family. Because the MC33071D is built on quality bipolar fabrication with innovative design concepts rather than JFET input devices, it combines wide signal swing capability with fast settling behavior over an unusually wide supply range. Key features of this device include the wide 3.0 V to 44 V single-supply capability, 4.5 MHz gain-bandwidth product, 13 V/µs slew rate, and low input offset voltage of 3 mV typical (5 mV maximum per the distributor listing). The amplifier operates from a -40 °C to +85 °C ambient temperature range and is specified for standard (general-purpose) instrumentation, buffer and op-amp applications. Technically, the MC33071D combines a wide internal common-mode and output voltage range with bipolar input and output stages, which allows the output to swing close to the supply rails on low-supply designs while still tolerating industrial rails well above 44 V in feedback loops and sensing stages. The 4.5 MHz bandwidth combined with 13 V/µs slew rate means a 10 V output step settles in roughly a microsecond, fast enough for closed-loop control loops at audio and low-frequency instrumentation bandwidths. Typical uses include industrial sensor signal conditioning, precision current-sense and voltage-feedback networks in power supplies, low-frequency audio driver stages, transducer and bridge preamplifiers, and general-purpose buffering where the supply rail can exceed the 18 V limit of typical 5 V single-supply op amps. When designing with this part, remember that the wide supply rating is a maximum, not a target. Keep input and output common-mode voltages inside the linear input range, place a 0.1 µF ceramic bypass capacitor at each supply pin with additional bulk capacitance nearby, and check output swing headroom at the highest ambient temperature. This page consolidates supply-range, bandwidth, slew-rate and offset specifications together with drop-in alternatives and practical layout guidance, so you can select the amplifier and the surrounding passive network without rebuilding the design from scratch.

RFQ İletişim
MC33071P - 3-44V Single Operational Amplifier | onsemi
MC33071P

MC33071P - 3-44V Single Operational Amplifier | onsemi

The onsemi MC33071P is a single general-purpose operational amplifier designed for single-supply operation from 3.0 V to 44 V. It provides a maximum input offset voltage of 5 mV, a gain-bandwidth product of 4.5 MHz, and supply current of 1.9 mA in an 8-pin PDIP package. The device is suited to industrial instrumentation, sensor conditioning, power-control loops, and signal-processing systems requiring wide supply-voltage tolerance. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The MC33071 belongs to the precision operational-amplifier hierarchy, combining a wide common-mode input range, single-supply operation, and general-purpose signal handling in one package. Its ability to operate from a 3.0 V supply supports modern low-voltage systems, while the 44 V upper limit accommodates higher-voltage industrial rails. Key electrical characteristics include a 5 mV maximum input offset voltage and a 4.5 MHz gain-bandwidth product. These specifications make the amplifier useful for low-level AC signal paths where input offset can influence accuracy and where bandwidth determines the range of signals that can be amplified without excessive gain reduction. The 1.9 mA supply current supports power-conscious designs while retaining useful operating speed. The MC33071P uses a conventional bipolar operational-amplifier architecture. In a typical non-inverting configuration, the input signal is applied to the non-inverting terminal and feedback is returned to the inverting terminal. Its broad supply range allows operation from unregulated or industrial supply sources, although input common-mode and output-swing limits must be respected at each supply voltage. Typical uses include low-level sensor amplification, transducer buffering, industrial control loops, audio preamplification, and general analog signal conditioning. It can also form active filters and waveform-shaping circuits when the required gain and bandwidth remain within the device's operating limits. Bypass capacitors placed close to the supply pins help reduce noise and stabilize operation in practical layouts. The primary design trade-off is that a general-purpose bipolar amplifier does not provide the very low offset, low power, or rail-to-rail output performance of specialized modern amplifier families. Confirm common-mode range, output swing, input bias current, and stability requirements against the actual supply voltage before using it in precision or battery-powered systems. This product record combines the MC33071P electrical characteristics, package information, verified drop-in candidates, application guidance, and PCB design considerations. The comparison and selection material helps engineers distinguish same-family and cross-brand options without overlooking differences in supply range, bandwidth, offset voltage, or package.

RFQ İletişim
MC33071PG - 4.5 MHz, 13 V/us Single-Supply Op Amp | onsemi
MC33071PG

MC33071PG - 4.5 MHz, 13 V/us Single-Supply Op Amp | onsemi

The onsemi MC33071PG is a general-purpose, single-circuit operational amplifier with a 4.5 MHz gain-bandwidth product, 13 V/us slew rate, and single-supply operation from 3.0 V to 44 V. The device is packaged in an 8-pin through-hole DIP measuring 0.300 inch, or 7.62 mm, in pitch. An operational amplifier is a voltage-feedback analog IC that uses differential input voltage to produce an amplified output voltage. The MC33071 belongs to the broader single-amplifier, general-purpose amplifier hierarchy, where it combines high bandwidth and rapid slew rate with the ability to operate from a positive supply without a negative rail. This makes it useful for industrial signal conditioning, control, and instrumentation circuits. The main performance characteristics are a 4.5 MHz gain-bandwidth product, 13 V/us slew rate, and 1.9 mA supply current. Its high slew rate allows the output to track large-amplitude input changes quickly, while the 4.5 MHz bandwidth supports higher-frequency closed-loop operation than ordinary low-frequency general-purpose amplifiers. The single-supply range permits direct use in 3.0 V to 44 V systems. The MC33071 uses quality bipolar fabrication and a bipolar monolithic operational-amplifier architecture rather than JFET input technology. According to the onsemi product page, the family provides fast settling performance and broad supply-voltage operation. Its single-ended output and single-amplifier configuration simplify designs that require one independent signal-conditioning channel per package. Typical applications include industrial process-control loops, sensor-signal conditioning, low-level instrumentation, motor-feedback amplifiers, and general analog signal processing. The wide supply range is particularly useful in industrial equipment where intermediate rails may be present. In battery-powered systems, the 3.0 V lower limit supports low-voltage operation, although supply current should be included in the overall power budget. For stable operation, follow the manufacturer datasheet when selecting external bias resistors, feedback components, and supply-decoupling capacitors. The input common-mode range and output swing depend on the supply voltage, so verify the operating-point requirements of the target circuit. A low-noise bypass capacitor placed close to the supply pins can reduce ripple coupled into the amplifier output. This product page combines the MC33071PG operating limits, package details, verified drop-in candidates, and application-specific design guidance to help engineers evaluate the amplifier before completing a PCB design.

RFQ İletişim
MC33072PG - Dual 44V 4.5MHz Op Amp | onsemi
MC33072PG

MC33072PG - Dual 44V 4.5MHz Op Amp | onsemi

The onsemi MC33072PG is a dual general-purpose operational amplifier with a 3.0 V to 44 V supply range, 4.5 MHz gain-bandwidth product, and 13 V/us slew rate, supplied in an 8-pin PDIP package. The device provides two amplifiers in one package and supports both split-supply and single-supply operation, making it suitable for industrial analog signal chains. An operational amplifier is an analog building block that provides high open-loop gain and uses negative feedback to amplify or process signals. The MC33072 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog signal-processing IC, and semiconductor. Its bipolar construction avoids JFET input devices while providing a practical combination of bandwidth, slew rate, input characteristics, and supply flexibility. The two amplifier sections offer 5 mV input offset voltage and a nominal 97 dB common-mode rejection ratio. Their 4.5 MHz gain-bandwidth product supports signal bandwidth beyond audio fundamentals, while the 13 V/us slew rate allows relatively rapid transitions. A 3.0 V to 44 V operating range accommodates conventional ±15 V supplies, lower-voltage asymmetric rails, and higher industrial supply arrangements when the circuit and output limits permit. The MC33072 series uses quality bipolar fabrication and monolithic construction. Each channel can operate as an inverting amplifier, non-inverting amplifier, voltage follower, comparator, or general feedback stage when suitable output swing and stability conditions are respected. Because it is a dual amplifier, both channels share the package supply pins and ground connection, allowing two related signal operations to be implemented in one component. Typical uses include industrial sensor conditioning, current-loop receivers, audio preamplification, active filters, waveform shaping, and general instrumentation. The 13 V/us slew rate is beneficial for low-amplitude, higher-frequency signals, while the 5 mV offset specification supports accurate closed-loop operation around a stable reference. Its single-supply capability is useful in portable and embedded equipment where generating a negative rail would otherwise add cost and complexity. Design the circuit around the manufacturer's recommended operating region and ensure the input common-mode range and output swing remain valid at the selected supply voltage. Keep feedback-loop compensation stable, place decoupling capacitors close to the supply pins, and route high-impedance input nodes with short traces and suitable guarding. The 8-pin PDIP package is intended for through-hole assembly and thermal evaluation on the board rather than compact surface-mount designs. This page combines the manufacturer's MC33072 product information with package characteristics, drop-in alternatives, application guidance, and practical circuit-design notes. It is intended to accelerate component selection while preserving the need to verify operating limits, external circuitry, and PCB-specific requirements before production release.

RFQ İletişim
MC33074AP - 44V Quad Op Amp, 4.5MHz, 14-DIP | onsemi
MC33074AP

MC33074AP - 44V Quad Op Amp, 4.5MHz, 14-DIP | onsemi

onsemi MC33074AP is a quad general-purpose operational amplifier with four single-ended amplifiers in a 14-pin plastic DIP package. It supports single-supply operation from 3.0V to 44V and provides 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3mV input offset voltage. The four amplifiers are designed for broad industrial, instrumentation, signal-conditioning, and control applications requiring economical precision. An operational amplifier, or op amp, is a high-gain differential amplifier whose open-loop behavior is shaped by external feedback. The MC33074AP belongs to the bipolar operational-amplifier family within the broader amplifier IC and analog semiconductor hierarchy. Each of its four channels can operate from a common positive supply and ground while supporting applications that involve signal amplification, buffering, comparisons, summing, and feedback-controlled analog circuits. The MC33074AP combines a 4.5MHz gain-bandwidth product with a 13V/us slew rate, allowing useful bandwidth beyond audio frequencies and rapid output transitions in transient signals. Its 3mV input offset voltage provides a defined level of input imbalance that must be included in precision-chain error budgets. The 3.0V to 44V supply range covers low-voltage circuits, conventional ±15V industrial systems, and higher single-supply rails. The monolithic quad construction reduces the number of separate amplifier packages required on a board. The bipolar internal design avoids the input-bias-current behavior associated with JFET-input amplifiers. This makes the MC33074AP appropriate for general-purpose signal conditioning where input bias current, offset voltage, slew rate, and supply range are the principal selection criteria. Because four amplifiers share one package, thermal behavior, supply decoupling, unused-channel handling, and channel-to-channel matching should be considered together rather than treating each section as an isolated component. Typical uses include industrial sensor interfaces, low-level control-signal amplification, audio preamplification, active filtering, waveform conditioning, and four-channel monitoring systems. The 44V maximum supply also provides headroom for systems with elevated rail voltages, although the complete circuit must remain within the absolute maximum ratings of every connected device. Grounded-source sensors, transducers, and analog front ends can benefit from the channel count and common package organization. For a new design, confirm the 14-pin DIP footprint and verify every pin function against the manufacturer pin-description table before layout release. Place the power-supply bypass capacitor close to the supply pin, provide a stable ground reference, and avoid leaving unused op-amp inputs floating. Confirm output swing, common-mode range, stability with the intended feedback network, and required noise performance at the actual supply voltage and signal frequency. This product page combines the manufacturer device information with practical supply, layout, comparison, and selection guidance. It also distinguishes exact package compatibility from merely similar amplifier functions, helping engineers identify replacements that can be considered for a PCB-level substitution and those that require a broader redesign.

RFQ İletişim
MC33074PG - Quad 4.5MHz 44V Op Amp | onsemi
MC33074PG

MC33074PG - Quad 4.5MHz 44V Op Amp | onsemi

onsemi MC33074PG is a general-purpose quad operational amplifier with four single-ended amplifier circuits, a 3.0 V to 44 V supply range, 4.5 MHz gain-bandwidth product, and 13 V/µs slew rate. The device is packaged in a 14-pin PDIP package measuring 0.300 inch, or 7.62 mm, in pitch. An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify voltage differences between its inputs. The MC33074 belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy. It is designed for general-purpose instrumentation, signal conditioning, and feedback-control circuits that can operate from a single supply or split supply. Its common-mode range includes ground potential, which is especially useful in circuits powered from one battery or one low-voltage rail. The MC33074PG combines 4.5 MHz gain-bandwidth product with a 13 V/µs slew rate, allowing it to process small signals while responding to moderate-amplitude changes without JFET input transistors. The quad configuration places four amplifiers in one 14-pin PDIP package, reducing component count and board space. A 5 mV input offset-voltage figure supports applications requiring repeatable DC amplification and active filtering. The 3.0 V to 44 V supply range accommodates conventional industrial and instrumentation voltage rails. The bipolar implementation supports operation from split supplies as well as single-supply configurations. This flexibility is useful when a circuit must process signals centered near ground or interface with sensors whose output spans a positive rail. Because the amplifiers share a common package, each channel can perform a different task, such as input amplification, filtering, buffering, error amplification, or output-current-voltage conversion. Typical uses include low-frequency instrumentation amplifiers, active filters, transducers, sensor-conditioning modules, audio preamplifiers, power-supply control loops, and general industrial control systems. The 4.5 MHz bandwidth is suitable for moderate-frequency precision signal paths, while the 13 V/µs slew rate provides useful transient response for comparator-like and feedback-control tasks. System designers should still verify output swing, output-current capability, input-bias-current effects, and stability for the selected gain and load. For a stable PCB implementation, use the 14-pin PDIP footprint, provide adequate supply bypassing, and route sensitive input and feedback traces away from high-current outputs. Decoupling capacitors should be placed close to the supply pins. Confirm the common-mode and output-swing limits against the actual circuit rails, especially in single-supply designs where the output may not swing fully to either supply rail. This product record combines the MC33074 family electrical characteristics, package information, sourcing guidance, verified drop-in options, and practical design notes. It helps engineers identify the correct quad bipolar amplifier, evaluate replacement choices, and plan instrumentation and industrial signal-conditioning layouts around the same 14-pin PDIP footprint.

RFQ İletişim
MC33077P - 37 MHz Low-Noise Dual Op Amp | onsemi
MC33077P

MC33077P - 37 MHz Low-Noise Dual Op Amp | onsemi

The onsemi MC33077P is a dual, general-purpose operational amplifier built with precision bipolar design techniques, providing a 37 MHz gain-bandwidth product and an 11 V/µs slew rate in an 8-pin PDIP package. It is intended for instrumentation, signal-conditioning, and amplification applications that require low noise, high frequency response, and precise channel matching. An operational amplifier, or op amp, is an analog active device that amplifies the difference between two input voltages. The MC33077P contains two independent amplifier circuits in one monolithic package, making it a dual op amp. Within the product hierarchy, it belongs to the operational amplifier and analog amplifier categories, where it provides a higher-speed alternative to general-purpose precision amplifiers. The MC33077 family uses innovative bipolar construction, analog resistor trimming, and dual-doublet frequency compensation. Analog trimming is used to obtain low input offset voltages, while the precision-matching approach supports closely matched amplifier channels. These techniques support applications in measurement systems, audio and communication circuits, active filters, and low-level analog signal chains. Verified distributor information identifies the MC33077P as a 2-circuit, 8-PDIP general-purpose amplifier with 37 MHz bandwidth. A separate distributor listing reports an 11 V/µs slew rate, indicating that the device can support signal transitions well beyond audio frequencies when the surrounding circuit permits. Exact noise density, input bias current, input offset voltage, supply-current, and common-mode limits were not included in the supplied verification data and must be confirmed against the manufacturer datasheet before design release. Typical uses include instrumentation preamplification, active filtering, audio signal conditioning, and general high-frequency analog processing. In a typical signal chain, the device would follow a low-amplitude sensor or filter stage and drive a higher-impedance ADC input, buffer, or measurement front end. Because the amplifiers are internally matched, dual-channel differential or ratiometric measurements are practical when board layout and resistor matching are controlled. The primary design consideration is ensuring that the surrounding circuit does not degrade the amplifier's noise and accuracy performance. Place decoupling capacitors close to the supply pins, keep feedback-loop routing short, and avoid parasitic capacitance on high-impedance input nodes. Confirm the exact pinout, supply range, noise specifications, input common-mode limits, and output-current capability in the onsemi MC33077 datasheet before layout release.

RFQ İletişim
MC33078D - Dual Low-Noise 15MHz Op Amp | Texas Instruments
MC33078D

MC33078D - Dual Low-Noise 15MHz Op Amp | Texas Instruments

The Texas Instruments MC33078D is a bipolar dual operational amplifier with two independent amplifiers, 4.5 nV/√Hz input-voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is supplied in an 8-pin SOIC package and is intended for audio and data-signal applications operating from -40 °C to 85 °C. A dual operational amplifier combines two amplifiers in one package, providing a practical path from analog signal conditioning to broader voltage-amplifier and analog IC functions. Each channel can amplify, buffer, filter, or drive a defined analog signal when used with suitable external components. MC33078D is particularly useful where low noise, wide bandwidth, and fast large-signal response are more important than the very low power consumption associated with CMOS-only amplifiers. The MC33078D uses bipolar technology, which supports low-noise operation and audio-focused performance. Its 4.5 nV/√Hz input-noise figure is suited to high-fidelity audio preamplification, microphone-stage signal conditioning, and low-level instrumentation. A 15 MHz gain-bandwidth product supports higher closed-loop bandwidth than slower general-purpose precision amplifiers, while the 7 V/µs slew rate provides improved ability to reproduce large-amplitude signals without excessive distortion. Two independent channels in one package reduce board area for balanced, differential, or multi-stage analog circuits. The 8-pin SOIC (D) package uses a familiar surface-mount footprint and supports automated assembly. Because its dual topology is not rail-to-rail by specification, applications must account for the allowable input and output voltage ranges when using single-supply or dual-supply configurations. Decoupling and stable feedback-network design remain essential for low-noise performance. Typical uses include stereo audio input amplification, active equalization, low-level sensor conditioning, line-stage amplification, and mixed-signal filtering. The two channels may also implement separate gain blocks, buffers, or active filters when the required common-mode range and output swing fit the application. In audio designs, low-noise operation helps preserve quiet signal paths, while the 15 MHz bandwidth and 7 V/µs slew rate provide headroom for detailed waveform reproduction. When laying out the circuit, place the power-supply bypass capacitor close to the supply pins and keep feedback resistors and input components compact to minimize parasitic capacitance and noise pickup. Verify gain-bandwidth and stability requirements with the actual noise-gain network. Single-supply operation may require biasing or AC coupling if the source cannot reach ground, so confirm the input common-mode range before finalizing the schematic. This product page combines manufacturer specifications, package information, practical analog-design guidance, and verified drop-in alternatives. It also highlights the exact differences between same-manufacturer and cross-manufacturer options, helping engineers compare compatibility, bandwidth, noise, temperature range, and application fit before making a board-level replacement decision.

RFQ İletişim
MC33078N - Dual Low-Noise 15MHz Op Amp | STMicroelectronics
MC33078N

MC33078N - Dual Low-Noise 15MHz Op Amp | STMicroelectronics

STMicroelectronics MC33078N is a monolithic dual bipolar operational amplifier optimized for low-noise audio and data-signal applications. The device provides two amplifiers, 4.5 nV/√Hz voltage-noise density, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate in an 8-pin Mini DIP package. It supports both single-supply and dual-supply operation, allowing its dual amplifier to process audio channels or implement gain, filtering, buffering, and signal-conditioning functions. An operational amplifier is a high-gain differential amplifier whose inverting and non-inverting inputs are compared to produce an amplified output. The bipolar input stage of the MC33078N combines low voltage noise with a wide gain-bandwidth product and high slew rate. In the broader semiconductor hierarchy, the MC33078N is an analog amplifier IC, more specifically a dual low-noise operational amplifier used in audio, instrumentation, and general-purpose signal-processing circuits. The principal performance features include 4.5 nV/√Hz input-voltage noise, 15 MHz gain-bandwidth product, and 7 V/µs slew rate. Its two amplifier channels provide design economy in stereo audio preamplifiers, active filters, line drivers, and instrumentation. The 8-pin Mini DIP package is also suitable for through-hole construction and prototyping where dual-line access and straightforward manual assembly are useful. The bipolar architecture provides the fast large-signal response needed for audio signals while retaining low noise for microphone-level and line-level work. The 15 MHz gain-bandwidth product supports wider closed-loop bandwidth than a low-frequency general-purpose amplifier, while the 7 V/µs slew rate helps the device reproduce large-amplitude waveforms without excessive distortion. Supply topology determines the usable common-mode and output-voltage ranges, so single- and dual-supply circuits require different biasing arrangements. Typical applications include stereo audio preamplification, active crossover and equalization networks, microphone preamplifiers, line-level buffers, active filters, sensor signal conditioning, and general dual-channel analog processing. In stereo equipment, the two channels can process left and right signals independently, reducing component count and helping maintain matched channel layouts. For new PCB designs, place the decoupling capacitor close to the supply pin and connect the exposed return path directly to the ground plane. When replacing an existing MC33078 footprint, verify the exact power-supply range, common-mode limits, output swing, noise characteristics, and stability requirements rather than relying only on the DIP-8 outline. This page combines manufacturer specifications, cross-reference information, practical application guidance, and package-aware replacement analysis to support faster engineering evaluation and sourcing.

RFQ İletişim
MC33078P - Dual 16MHz Low-Noise Op Amp | Texas Instruments
MC33078P

MC33078P - Dual 16MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments MC33078P is a bipolar dual operational amplifier with 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and 4.5 nV/√Hz input voltage noise, supplied in an 8-pin PDIP package. The device supports single-supply and dual-supply operation over a voltage range of ±5 V to ±18 V and is intended for quality audio and data-signal processing applications. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to increase the voltage difference between two inputs. In the wider hierarchy, an op amp belongs to amplifiers, analog integrated circuits, and signal-chain conditioning devices. The MC33078P contains two independent amplifiers in one package, allowing one package to serve two channels while reducing board area and simplifying dual-audio or dual-data-signal designs. The MC33078/9 family uses bipolar transistor technology with high-frequency PNP input transistors. This architecture provides low input voltage noise, high gain-bandwidth product, high slew rate, low total harmonic distortion of 0.002%, and a low input offset voltage of 0.15 mV. These characteristics make the amplifier suitable for audio preamplification, filtering, instrumentation, and general-purpose analog signal conditioning where both small-signal fidelity and bandwidth are important. The two channels operate independently from the same supply pins. Its 16 MHz gain-bandwidth product allows useful closed-loop bandwidth well below the unity-gain frequency, while the 7 V/µs slew rate supports faster large-signal transitions than many general-purpose bipolar op amps. Noise and distortion figures should therefore be evaluated in the same signal bandwidth and output amplitude used in the target circuit; headline values do not describe complete system performance by themselves. Typical uses include microphone and line-level audio amplification, active filters, analog instrumentation, low-level sensor conditioning, and dual-channel signal processing. The 8-pin PDIP package is suitable for through-hole construction, prototyping, repair work, and applications where the larger package is acceptable. Local bypass capacitors close to the supply pins remain important for stable operation and low-noise performance. The principal design trade-off is package size rather than electrical capability: PDIP-8 is easy to install manually but occupies more PCB area than surface-mount dual-op-amp packages. Designers should preserve adequate output-current headroom for capacitive loads, verify stable operation with the selected feedback network and load, and avoid assuming that low-noise input devices are interchangeable with FET-input amplifiers because bias-current and distortion behavior differ. This page consolidates the verified manufacturer specifications, distributor availability references, and engineering-focused selection guidance for MC33078P. It also distinguishes documented MC33078-family options from true pin-compatible replacements, helping engineers avoid treating merely similar amplifiers as drop-in substitutes.

RFQ İletişim
MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi
MC33079D

MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi

onsemi MC33079D is a low-noise, quad operational amplifier with four amplifiers in a 14-pin SOIC package. Its headline specifications are 4.5 nV/√Hz voltage-noise density, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The MC33079 uses bipolar input transistors and is intended for audio and data-signal processing applications requiring low noise, high-frequency response, low distortion, and stable operation. An operational amplifier, or op amp, is a high-gain differential amplifier whose external feedback defines its gain and bandwidth. Within the semiconductor hierarchy, an op amp belongs to the linear amplifier and analog signal-conditioning categories. It is used to amplify weak sensor signals, buffer high-impedance sources, implement active filters, and provide gain in audio and control paths. The MC33079 integrates four amplifiers in one package, reducing board area while providing consistent device-level matching. The MC33079D combines 4.5 nV/√Hz low-voltage-noise performance with a 15 MHz gain-bandwidth product. Its 7 V/µs slew rate supports faster large-signal transitions than slower general-purpose amplifiers. Additional features include 0.002% distortion, a large output-voltage swing, 2 kV ESD protection, and a macromodel for simulation. These characteristics make the device relevant to microphone preamplification, active audio crossover networks, audio buffer stages, and precision low-frequency signal conditioning. The bipolar architecture uses high-frequency PNP input transistors to provide low input-voltage noise. Because the amplifiers are not rail-to-rail, system designers should verify input common-mode range and output swing against the selected supply voltage. The listed operating-voltage range of 2.5 V to 15 V permits operation from low-voltage analog systems through conventional ±15 V bipolar supplies. The four amplifiers share a common package, although each output still requires suitable output-current and stability analysis for its load. Typical uses include four-channel audio buffering, low-level microphone amplification, active equalization, filtering, instrumentation interfaces, and general-purpose analog signal processing. In multi-amplifier designs, adjacent channels can implement gain, filtering, and drive functions without requiring four separate packages. The device can also serve in laboratory and industrial control circuits where low noise and a 15 MHz bandwidth are more important than rail-to-rail input or output operation. The primary design consideration is power-supply configuration. Decouple each supply connection with a local ceramic bypass capacitor, maintain a short return path, and place input and feedback components close to the relevant amplifier pins. Avoid using the quad amplifier merely because four circuits are required: confirm common-mode limits, output-swing headroom, capacitive-load stability, noise-gain bandwidth, and channel-to-channel layout symmetry before releasing the PCB. This product record combines the MC33079D manufacturer-datasheet specifications, package information, search queries, and cross-reference findings with practical design guidance. It also highlights genuine replacement constraints: a mechanically similar 14-pin SOIC amplifier is not automatically a drop-in replacement, so common-mode range, bias current, stability, noise, and exact pin assignment must be checked before substitution.

RFQ İletişim
MC33079DG - 16MHz Low-Noise Quad Op Amp | onsemi
MC33079DG

MC33079DG - 16MHz Low-Noise Quad Op Amp | onsemi

The onsemi MC33079DG is a low-noise, general-purpose quad operational amplifier with four amplifiers per package, a 16 MHz gain-bandwidth product, a 7 V/us slew rate, and a 14-pin SOIC package. It operates from ±2.5 V to ±9 V, with a maximum operating voltage of ±18 V, making it suitable for dual-rail audio, instrumentation, and general signal-processing systems. An operational amplifier is an active analog component that uses negative feedback to amplify the difference between two input voltages. The quad configuration places four amplifiers in one package, reducing board area for multichannel audio preamplifiers, sensor-conditioning circuits, active filters, and low-level signal-processing systems. The MC33078/79 family uses bipolar circuitry and high-frequency PNP input transistors to combine low input-voltage noise with useful high-frequency performance. The MC33079DG provides 4.5 nV/sqrt(Hz) voltage-noise density, a 16 MHz gain-bandwidth product, and a 7 V/us slew rate. Its typical harmonic-distortion figure is 0.002%, while common-mode rejection is 80 dB. The low-noise input stage is particularly useful when amplifying weak signals from microphones, sensors, and audio sources without adding unnecessary broadband noise. The output stage supports large voltage swings for improved dynamic range in line-level circuits. The amplifier's 16 MHz bandwidth makes it suitable for signal paths operating well above the audio band. Its 7 V/us slew rate also allows comparatively rapid transitions when driving higher-impedance loads. The family specification identifies ESD protection of 2 kV, a macromodel for circuit simulation, and excellent frequency stability. These characteristics make the device suitable for precision audio, active filtering, low-level instrumentation, and mixed analog-signal processing. Typical uses include four-channel audio preamplification, microphone conditioning, active low-pass or band-pass filters, buffered sensor outputs, and general-purpose dual-supply amplification. Because all four amplifiers share one package, PCB space and supply routing can be organized efficiently. The 14-SOIC outline is also convenient for through-hole assembly and conventional prototype-board layouts. Design with adequate supply decoupling near pins 4 and 11 and confirm that the required output swing remains inside the amplifier's operating limits. The 80 dB common-mode rejection helps reject common-mode interference, but input and output layout still determines actual system noise performance. Avoid excessive capacitive loading because it can reduce stability and alter the practical slew rate. This product summary combines the manufacturer amplifier specifications, package information, operating limits, drop-in family options, and practical design guidance. It also distinguishes electrical and packaging variants so engineers can identify a suitable replacement without changing the 14-SOIC footprint.

RFQ İletişim
MC33079DT - Low-Noise Quad Op Amp | STMicroelectronics | Audio
MC33079DT

MC33079DT - Low-Noise Quad Op Amp | STMicroelectronics | Audio

The STMicroelectronics MC33079DT is a monolithic quad operational amplifier designed for low-noise audio signal paths, featuring 4.5 nV/√Hz voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is packaged in a 14-pin SOIC for surface-mount production assemblies. Four amplifiers in one package reduce board area and simplify multi-channel audio circuitry. An operational amplifier is a voltage-gain circuit element used to amplify small signals while improving impedance characteristics. The MC33079 belongs to the low-noise operational-amplifier family within the broader linear-amplifier and signal-conditioning hierarchy. Its low-noise input stage is particularly useful when the amplified signal originates from microphones, pickups, sensors, or line-level audio sources. The four internal amplifiers share a common supply architecture and are intended for low-voltage audio applications. Key performance characteristics include 4.5 nV/√Hz input-voltage noise and 15 MHz gain-bandwidth product. The 7 V/µs slew rate supports faster signal transitions, while the manufacturer reports very low distortion of 0.002%. These characteristics make the device suitable where low noise, bandwidth, and signal fidelity must coexist in a compact package. MC33079DT is a general-purpose quad amplifier rather than a dedicated audio-output driver. Each amplifier includes the conventional non-inverting and inverting inputs, an output, and supply pins. The SOIC-14 package provides a practical surface-mount option for industrial and consumer audio boards, active crossovers, preamplifiers, mixers, and instrumentation. Its four-channel organization makes it suitable for multichannel systems requiring consistent amplifier performance. Typical uses include microphone preamplification, line-level buffering, active equalization, audio summing, and low-level sensor amplification. Designers should select suitable input and feedback networks based on the required noise gain, bandwidth, and output swing. The signal source and load must also be checked against the device's supply-voltage and common-mode limits before layout begins. For PCB implementation, place input and output paths to minimize parasitic capacitance and keep feedback resistors close to the relevant amplifier pins. Decoupling capacitors should be positioned near the supply pins, while analog and high-impedance traces should remain away from switching nodes. Stable feedback ratios and clean grounding are especially important when low-level audio noise must remain below the source's own noise floor. This page combines the MC33079DT's documented noise, bandwidth, slew-rate, distortion, and package characteristics with application-focused guidance, pin-compatible replacement analysis, and practical PCB considerations for evaluating the amplifier in new or existing audio designs.

RFQ İletişim
MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio
MC33079N

MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio

STMicroelectronics MC33079N is a monolithic quad operational amplifier designed for audio and general signal-processing applications, with four amplifiers in a 14-pin DIP package. Its headline characteristics are 4.5 nV/√Hz voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is intended for designs that require low-noise signal amplification with sufficient bandwidth to handle audio signals and other low-frequency waveforms. An operational amplifier is a voltage-gain building block used throughout analog electronics. The MC33079 belongs to the op-amp hierarchy, where it provides amplification, buffering, filtering, and active gain for analog signals. Its four amplifiers share a common power supply in one package, allowing one quad device to implement several stages of an audio preamplifier, mixer, line amplifier, or measurement circuit while reducing board area. The MC33079N combines low voltage noise with high-frequency performance. The 4.5 nV/√Hz noise density supports low-noise audio amplification, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio-frequency closed-loop designs. A 7 V/µs slew rate supports large-signal reproduction and reduces the likelihood of slew-rate distortion in higher-gain stages. The manufacturer also specifies very low distortion of 0.002%, along with strong phase and gain margins. Its four-circuit organization provides flexibility for mixed-signal layouts. Each amplifier can perform a separate function, such as input amplification, active filtering, buffering, or output drive, when the system does not require all four stages simultaneously. Since this is an analog integrated circuit, its performance depends on suitable bypass capacitors, stable feedback networks, appropriate source and load impedances, and careful consideration of common-mode and output-voltage limits. Typical uses include stereo and multichannel audio preamplification, active crossover networks, microphone and line-level signal conditioning, servo-control loops, and instrumentation requiring multiple amplifiers. The quad format can also reduce component count by replacing several individual single or dual amplifier packages. Where an existing amplifier section uses an equivalent 14-pin quad footprint, the MC33079N can serve as a focused upgrade for lower-noise audio operation after checking pin functions and operating limits. Design the supply rails to remain within the device's operating requirements and place the bypass capacitors close to the power pins. Keep feedback loops short, use resistors and capacitors suitable for the intended audio bandwidth, and verify stability with the selected gain and load. An oscilloscope measurement of output clipping, noise, and slew behavior can confirm that the overall circuit, rather than the op amp alone, meets the system specification. This page organizes the MC33079N's principal electrical characteristics, package details, application guidance, drop-in replacement options, and engineering trade-offs. It is designed to help engineers evaluate noise, bandwidth, slew rate, distortion, and compatibility before integrating the amplifier into an audio or precision analog design.

RFQ İletişim
MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi
MC33079PG

MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi

The onsemi MC33079PG is a low-noise, general-purpose quad operational amplifier fabricated with bipolar technology and optimized for audio and data-signal processing. The device contains four amplifiers in a 14-pin PDIP package and operates from a 5 V to 18 V supply. Its headline specifications include a 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and low-noise bipolar input stages using high-frequency PNP input transistors. An operational amplifier is a voltage-controlled, high-gain differential amplifier used to amplify small input signals and drive higher-level circuits. Within the semiconductor hierarchy, an op amp belongs to the amplifier IC and analog signal-processing categories. The MC33079 combines four amplifiers in one package, reducing board area when a design requires multiple gain stages, buffers, summing amplifiers, or active filters. The MC33079PG offers a 16 MHz gain-bandwidth product and a 7 V/µs slew rate. These figures make it suitable for audio preamplification, active filtering, signal conditioning, and general instrumentation. High-frequency PNP input transistors are used to obtain low input-voltage noise, while the bipolar process supports operation from single-supply rails beginning at 5 V. The package is a 14-pin PDIP with a 7.62 mm pin pitch. Its four-amplifier architecture provides a practical way to implement stereo or multichannel signal paths without using four separate packages. When configured with non-inverting gain, the bandwidth depends on the selected feedback components; higher closed-loop gain reduces usable bandwidth. The 7 V/µs slew rate also influences large-signal behavior, so square-wave and high-fidelity audio tests should be evaluated against the intended load and feedback network rather than bandwidth alone. Typical uses include microphone preamplification, audio mixer stages, active equalization, sensor conditioning, low-frequency active filters, and general-purpose instrumentation. The general-purpose designation indicates that the device is not limited to one application topology. It is especially relevant where several low-noise amplification channels are needed with a shared supply and a conventional through-hole package. For PCB implementation, maintain short feedback paths and place compensation or filtering components close to the relevant input and output pins. The ±18 V maximum supply rating must include tolerance, transient overshoot, and any rail-to-rail total. Decouple the supply near pin 8 with a short ground return to reduce supply-noise coupling into the four amplifier channels. This product page combines the manufacturer’s device description with package, electrical, application, lifecycle, and replacement guidance. It also emphasizes the practical distinctions between the MC33079PG and commonly discussed alternatives so that engineers can determine whether the 14-pin PDIP footprint, bipolar input stage, supply range, and 16 MHz bandwidth meet the design requirements before committing to a layout.

RFQ İletişim
MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi
MC33102P

MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi

The onsemi MC33102P is a dual operational amplifier with a two-state Sleep-Mode architecture, combining two amplifier channels in an 8-pin PDIP package. It is designed for low-power signal conditioning where the amplifier can remain in a low-power sleep state while waiting for an input signal and switch to an awake state when amplification is required. The device is specified as a micropower operational amplifier with 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. An operational amplifier is an active analog signal-conditioning component that uses high-gain differential amplification to increase the voltage level of a weak or small signal. A dual operational amplifier contains two amplifier sections in one package, allowing two related signals to be processed simultaneously while reducing board area. The MC33102P adds Sleep-Mode technology to this familiar amplifier function, making it useful in portable instruments, sensor interfaces, battery-powered systems, and other applications where standby consumption matters. The MC33102P's main features include dual general-purpose amplifier channels, a sleep-mode operating state, an awake-mode operating state, 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. The low supply current supports designs that spend significant time monitoring or waiting for a valid input. The sleep and awake states provide a mechanism to control when the amplifier is intended to respond to signal activity. The dual configuration allows the part to handle two amplifier functions in one package, such as signal conditioning for two sensor channels, an instrumentation front end, or gain stages around a comparator and data-conversion system. The 4.6 MHz gain-bandwidth product supports moderate-bandwidth applications, while the 1.7 V/us slew rate provides useful response for slowly varying and low-to-moderate-frequency analog signals. Its PDIP-8 package is suitable for conventional through-hole PCB assembly and prototyping. When designing around the MC33102P, check the input common-mode range, output swing, supply-voltage limits, stability requirements, and the meaning of the sleep-mode control behavior in the manufacturer datasheet. Place the device close to the signal source when handling high-impedance nodes, provide normal bypassing at the supply pins, and account for input bias-current errors and offset voltage when resolving low-level signals. This product page combines the MC33102P device identity, package information, operating characteristics, sourcing guidance, comparison framework, and practical design notes. The information is intended to help engineers confirm pin compatibility, assess the dual low-power amplifier architecture, and select a suitable replacement or design approach without treating a different package or electrical function as a drop-in substitute.

RFQ İletişim
MC33121P - Low-Voltage SLIC Interface | Motorola | PBX
MC33121P

MC33121P - Low-Voltage SLIC Interface | Motorola | PBX

The Motorola MC33121P is a low-voltage Subscriber Line Interface Circuit (SLIC) designed to connect the four-wire side of a central office or PBX to a two-wire subscriber line in a 14-pin plastic DIP package. It provides battery feed, loop-termination AC impedance, hookswitch detection, adjustable transmit, receive, and transhybrid gains, and single or double fault indication. The verified MC33121P listing identifies a 14-PDIP package, while the available technical material specifies a minimum longitudinal balance of 58 dB. A Subscriber Line Interface Circuit, or SLIC, is an integrated telecommunications interface that replaces many discrete functions associated with a analog telephone line. In the broader hierarchy, it is a specialized line interface IC within interface ICs and telecommunications semiconductors. It bridges a central-office or PBX voice path and a subscriber loop while separating transmit and receive signals, supporting line termination, and exposing hookswitch and fault information to the surrounding codec or control electronics. The MC33121P integrates several line-facing functions into one device. Battery feed supplies the line, while proper loop termination establishes the intended AC impedance seen by the subscriber. Adjustable transmit, receive, and transhybrid gains allow the surrounding system to control voice-path levels and balance. Hookswitch detection reports line activity, and separate status outputs indicate single or double faults, reducing the number of external discrete monitoring elements. Transmit and receive signals are referenced to analog ground, while digital status and control signals are referenced to digital ground. This separation simplifies interconnection with codecs, filters, and digital control logic. The hookswitch and fault outputs are compatible with TTL/CMOS, and the power-down input permits local shutdown. These interface features make the MC33121P suitable for integrated access, subscriber-line, PBX, voice codec, and central-office interface designs. Typical uses include a PBX line card, a central-office subscriber interface, a two-wire telephone-line interface, a voice codec interface, a hookswitch monitor, and a line-fault indication circuit. In each case, the IC provides the physical subscriber-line interface while external circuitry handles codec conversion, call control, supervision, and system-level power management. Because this legacy device is a through-hole 14-pin DIP, it is most practical for legacy designs, repair assemblies, and industrial or telecommunications equipment that can accommodate through-hole leaded components. Designers should preserve separate analog and digital grounding paths and connect the device to the selected codec, filter, and line-conditioning network exactly as shown in the manufacturer application material. Before production use, verify the unavailable operating voltage, temperature range, loop-current limits, external-component values, and absolute maximum ratings against the manufacturer datasheet. Those parameters are not supplied in the verified excerpts and therefore cannot be safely inferred. This page consolidates verified distributor pricing, package information, interface functions, comparison fields, and practical implementation cautions. It also distinguishes documented MC33121P characteristics from unverified alternatives, avoiding unsupported claims that a different SLIC is truly pin-to-pin compatible.

RFQ İletişim
MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics
MC33171D

MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics

The STMicroelectronics MC33171D is a low-power single bipolar operational amplifier fabricated with quality bipolar processing and innovative design concepts, housed in an 8-pin SOIC package. It operates at 180 uA per amplifier, delivers a 1.8 MHz gain bandwidth product and a 2.1 V/us slew rate, and supports supply operation from 3 V to 44 V single-supply (or split supplies). An operational amplifier (op-amp) is an analog building block within the broader hierarchy of amplifier ICs and linear semiconductors. It amplifies the voltage difference between its inverting and non-inverting inputs with high open-loop gain, and its behavior in a circuit is set almost entirely by external feedback components. General-purpose op-amps such as the MC33171 series sit at the entry level of this taxonomy, below precision, high-speed, and instrumentation amplifier families, yet they remain the workhorse of analog signal conditioning. Key features of the MC33171 include its exceptionally low 180 uA supply current per amplifier, which makes it attractive for battery-powered and energy-conscious designs. The bipolar fabrication (without JFET device technology) gives robust input behavior and predictable industry-standard single-op-amp pinout. The wide 3 V to 44 V supply range allows operation from single low-voltage rails or from higher industrial buses, and the device is particularly suited for single-supply operation although it can run from split supplies. Technically, the MC33171/72/74 monolithic series combines the low static current with usable AC performance: the 1.8 MHz bandwidth covers audio and low-frequency instrumentation needs, while the 2.1 V/us slew rate supports moderate-amplitude signal swings without excessive distortion at those frequencies. Typical applications include battery-powered portable instruments, sensor signal conditioning, active filters, transducer amplifiers, and low-frequency comparators or level shifters in industrial control, where low quiescent drain and wide supply tolerance matter more than ultra-high speed. A key design consideration: because it is optimized for low power rather than high speed, allow adequate settling margin in feedback networks and avoid pushing large output swings near the 1.8 MHz bandwidth limit to prevent slew-induced distortion. This page adds value beyond the manufacturer datasheet by consolidating cross-brand availability context, drop-in alternative guidance, practical design notes, and sourcing access through the Request a Quote form.

RFQ İletişim
MC33171DT - 2.1MHz Low-Power Op Amp | STMicroelectronics
MC33171DT

MC33171DT - 2.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC33171DT is a single bipolar operational amplifier optimized for low consumption and moderate speed, delivering a 2.1 MHz gain-bandwidth product with a 2 V/µs slew rate. It operates from a single 4 V to 44 V supply or from dual ±2 V to ±22 V rails and consumes approximately 200 µA. The amplifier is packaged in an 8-pin SOIC, making it suitable for industrial control, instrumentation, signal conditioning, and general-purpose analog signal paths. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Within the broader hierarchy of analog and mixed-signal electronics, an operational amplifier belongs to the amplifier IC family and supports precision control, buffering, filtering, sensing, and feedback-based circuit functions. The MC33171 combines a bipolar input and output stage with a low-current architecture intended to preserve useful speed without the higher consumption associated with many general-purpose precision amplifiers. The MC33171DT's 2.1 MHz gain-bandwidth product supports signal paths where moderate bandwidth is more important than nanovolt-level input noise. Its 2 V/µs slew rate gives it the capability to process larger voltage changes quickly, while its approximately 200 µA consumption supports low-power signal-conditioning systems. The common-mode input range extends toward the lower supply rail, enabling single-supply operation from 4 V to 44 V. Dual-rail operation is also possible over a stated range of ±2 V to ±22 V. The 8-pin SOIC package provides a conventional surface-mount footprint for analog boards and simplifies assembly alongside mixed-signal components. Because this is a single-amplifier device, systems requiring multiple independent amplifier channels must use additional packages or a suitable multi-amplifier device. Designers should account for the operating voltage, common-mode range, output swing, stability with the selected feedback network, and external compensation requirements when designing a new circuit. Typical applications include industrial process-control loops, low-power sensor interfaces, audio and communication signal conditioning, active filters, and general-purpose amplification stages. The extended supply capability is useful in industrial systems where signal levels may vary widely. The low 200 µA consumption is particularly relevant when the amplifier operates continuously from a compact or space-constrained power budget. For reliable implementation, connect the supply pins to bypass capacitors and route feedback components to minimize parasitic effects. Maintain signal levels within the common-mode and output ranges, and verify stability with the actual load capacitance and source impedance. This page combines manufacturer specifications, package information, sourcing guidance, and practical design considerations for engineers evaluating the MC33171DT. For design trade-offs, compare the MC33171DT with the related MC33172DT and MC33174DT family members before fixing the BOM. Each option should be selected according to the required gain, bandwidth, slew behavior, and application circuit rather than package availability alone.

RFQ İletişim
MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics
MC33171N

MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC33171N is a single bipolar operational amplifier with a 2.1 MHz gain-bandwidth product, 2 V/us slew rate, 200 uA supply current, and a DIP-8 package. It supports single-supply operation from 4 V to 44 V, while its input common-mode range extends to the lower supply rail. These characteristics make the MC33171N suitable for low-power analog signal conditioning, industrial instrumentation, sensor interfaces, and general-purpose voltage amplification. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between two input voltages. The bipolar MC33171N belongs to the operational-amplifier, analog-IC, and semiconductor hierarchy. Its rail-to-rail input common-mode capability is particularly useful in single-supply systems because the input signal can approach the lower supply rail without requiring a negative power source. The principal features are a 2.1 MHz gain-bandwidth product, a 2 V/us slew rate, and a typical supply current of 200 uA. The 2.1 MHz bandwidth provides useful bandwidth for general-purpose analog stages, while the 2 V/us slew rate limits how quickly the output can follow large voltage changes. Low 200 uA consumption supports battery-powered and distributed instrumentation designs where amplifier power can dominate the system budget. The MC33171N uses a single bipolar amplifier architecture rather than a JFET-input implementation. This architecture combines low supply consumption with moderate operating speed and makes the device appropriate for continuous analog signal processing without the static bias current associated with higher-performance precision amplifiers. Its 4 V to 44 V single-supply range allows operation from conventional 5 V and 12 V rails as well as higher industrial supply voltages. Typical applications include low-frequency instrumentation amplifiers, current-sensor signal conditioning, buffered sensor outputs, industrial control inputs, and low-power analog measurement systems. The input common-mode range extending to the lower rail is valuable in systems powered from a single positive supply, where input signals can be close to ground. Gain and bandwidth should be selected together so that the closed-loop noise gain remains compatible with the 2.1 MHz gain-bandwidth product. A key design consideration is the relationship between supply voltage, output swing, and input range. Confirm that the required signal and output remain inside the operating limits before assigning a high closed-loop gain. Keep feedback routing short, place input and supply bypass capacitors close to their relevant pins, and avoid extending high-impedance input traces where leakage and interference can degrade accuracy. This product page combines the STMicroelectronics MC33171 operating characteristics with package guidance, pin assignments, application analysis, verified drop-in alternatives, and practical circuit-design notes. It is intended to help engineers select the amplifier, confirm footprint compatibility, and plan an efficient single-supply analog implementation.

RFQ İletişim
MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP
MC33171P

MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP

onsemi MC33171P is a single, general-purpose operational amplifier with a 3.0 V to 44 V supply range, low 180 uA operating current per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. The device is packaged in an 8-pin plastic dual in-line package (8-PDIP). Its bipolar input stage provides a practical alternative to JFET-input amplifiers in applications that do not require JFET characteristics. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MC33171 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. It can operate from a single supply or split supplies, allowing it to serve as a general-purpose amplifier, buffer, comparator, or active-filter building block in industrial, instrumentation, and control circuits. Key characteristics include the wide 3.0 V to 44 V operating range, 180 uA current consumption per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. These values position the device for low-power, moderate-bandwidth signal conditioning where a larger package is acceptable and through-hole assembly is preferred. The 8-PDIP format also simplifies prototyping, breadboarding, repair, and manual production processes. The bipolar fabrication approach provides the stated bandwidth and slew-rate performance without JFET-device technology. Because the operating supply extends to 44 V, the amplifier can accommodate higher-voltage systems than conventional low-voltage operational amplifiers. Designers must still verify input and output common-mode limits against the selected supply configuration before using the amplifier outside its intended operating region. Typical uses include low-frequency sensor conditioning, buffered transducer interfaces, audio preamplification, industrial control signals, power-supply feedback monitoring, and active analog filters. The 1.8 MHz gain-bandwidth product is suitable for many audio and instrumentation stages, while the 2.1 V/us slew rate supports reasonably clean responses to moderate-amplitude step inputs. When designing a board around the MC33171P, maintain adequate input and output voltage headroom, bypass the supply pins close to the device, and route high-impedance input signals with minimal leakage and contamination. Stable operation also depends on the feedback network, source impedance, output loading, and application-specific settling requirements. This product page combines the manufacturer's MC33171 family documentation, distributor package information, search-focused technical data, and practical design guidance. It also distinguishes verified drop-in alternatives from broader equivalents that may require different packages, supply ranges, or performance checks before substitution.

RFQ İletişim