5M570ZM100C5N - MAX V CPLD, 440 LE, 100-MBGA | Intel / Altera
MPN: 5M570ZM100C5N ✓ Aktif5M570ZM100C5N Genel Bakış
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL-like logic blocks on a single die with a central interconnect matrix. It sits in the broader programmable logic hierarchy as follows: CPLD -> programmable logic device (PLD) -> logic IC -> semiconductor. Compared to FPGAs, CPLDs offer deterministic timing, instant-on non-volatile configuration, lower static power, and superior suitability for glue-logic, I/O expansion, bus-interface bridging, and power-up control tasks. The MAX V family uses a flash-based configuration cell that retains bitstream without an external boot PROM, distinguishing it from SRAM-based FPGAs.
Key features include 440 macro cells distributed across 8 logic array blocks (LABs) with 57 per LAB, 440 flip-flops, 8 Kbits of user flash memory (UFM) for on-chip parameter storage, JTAG (IEEE 1149.1) and in-system programmability through Altera / Intel Quartus II or Quartus Prime, and 1.8 V core supply. The device supports multi-voltage I/O at 1.5 V, 1.8 V, 2.5 V, and 3.3 V, providing flexible interfacing without external level shifters.
The 5M570ZM100C5N uses a low-k 6-metal-layer CMOS process on a flash-based configuration cell. The non-volatile flash cell array eliminates configuration time at power-up, delivering < 1 ms I/O readiness, which is critical for system control plane functions that must be active before any FPGA or processor completes its boot sequence. The 100-MBGA package exposes the full MAX V feature set with maximum user I/O count for its logic density tier.
Typical applications include I/O expansion and glue-logic in industrial controllers, bus-interface bridging (e.g., parallel-to-LVDS or SPI-to-parallel), power-sequencer and reset-distribution networks, FPGA configuration and boot logic, and PCI/PCI-X interface arbitration. The non-volatile instant-on behavior also makes it well suited to safety-critical and brownout-resilient control paths.
When designing with the 5M570ZM100C5N, route all four GND balls to a continuous ground plane directly under the package to minimize inductance on simultaneous-switching outputs. Use a 0.1 µF X7R bypass capacitor on every VCCIO bank plus a single 10 µF bulk capacitor on VCCINT; place these within 100 mils of their respective balls.
This page synthesizes distributor pricing tiers, pin-compatible drop-in alternatives, and practical PCB/thermal design notes not found in the bare manufacturer datasheet - consolidating reference data engineers need to qualify the 5M570ZM100C5N for new designs in a single view.
Drop-in alternatifler için 5M570ZM100C5N — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller 5M570ZM100C5N (aynı form faktörü ve ayağa oturma) — farklı olan Package, Programming Interface, Operating Temperature, Mounting Type, Maximum Internal Frequency.
5M570ZM100C4N
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →5M570ZM100A5N
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →5M570ZM100I5N
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →5M570ZM100C5N Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Family | MAX V CPLD |
| Series | 5M570Z |
| Logic Elements / Macro Cells | 440 |
| Maximum User I/O Pins | 74 |
| Maximum Operating Frequency (fMAX) | 118.3 MHz |
| Pin-to-Pin Logic Delay (tPD) | 9 ns (typical, per datasheet) |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| User Flash Memory (UFM) | 8 Kbits |
| Configuration Memory Type | Non-volatile Flash |
| Paket | 100-ball MBGA (Micro FineLine BGA), 0.5 mm pitch |
| İşletim Sıcaklığı | 0C to +85C (commercial) |
| JTAG Support | IEEE 1149.1 boundary-scan + ISP |
| Programming Interface | JTAG / In-System Programming (Quartus II / Quartus Prime) |
| RoHS Durumu | Compliant |
| Montaj Türü | Surface Mount (BGA) |
5M570ZM100C5N 100-ball mbga (micro fineline bga), 0.5 mm pitch Pin Yapısı Kılavuzu
5M570ZM100C5N (100-ball mbga (micro fineline bga), 0.5 mm pitch paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: 5M570ZM100C5N.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
5M570ZM100C5N için uygundur 6 uygulamas: Industrial PLC I/O Expansion & Glue Logic, FPGA Configuration & Power-Sequencer Controller, Bus-Interface Bridging (Parallel to LVDS / SPI to Parallel), Consumer Electronics Display Control & Backplane Logic, Automotive Aftermarket ECU Customization & Brownout-Safe Logic, Telecom Line Card Glue Logic & Clock Distribution.
Industrial PLC I/O Expansion & Glue Logic
The 5M570ZM100C5N is well suited to industrial PLC I/O expansion where it provides 74 user I/O with multi-voltage 1.5 V to 3.3 V VCCIO support, enabling direct interface to 3.3 V logic sensors and 5 V tolerant legacy peripherals. Its non-volatile flash configuration boots in under 1 ms at power-up, so it is active before any downstream MCU or FPGA finishes initialization, making it ideal for pre-boot reset distribution and bus-isolation gating. The 440 macro cells and 118.3 MHz fMAX handle medium-complexity state machines such as encoder decoding, PWM generation, and interlock logic without consuming MCU cycles.
Önerilen
FPGA Configuration & Power-Sequencer Controller
The 5M570ZM100C5N's instant-on non-volatile flash configuration makes it ideal for controlling FPGA power-up sequencing and configuration handshaking. The CPLD can assert the FPGA PROGn line, monitor the CONF_DONE signal, and switch clock mux sources before the FPGA finishes its SRAM-based configuration, eliminating the need for a separate microcontroller. With 9 ns tPD and 118.3 MHz fMAX, the part can implement complex state machines that satisfy multi-rail power-up order requirements (e.g., 0.8 V core before 1.8 V PHY before 3.3 V IO) with deterministic timing.
Önerilen
Bus-Interface Bridging (Parallel to LVDS / SPI to Parallel)
The 5M570ZM100C5N's 74 user I/O and 440 macro cells are sufficient to implement common bus-bridge protocols such as parallel-to-LVDS conversion, SPI-to-parallel register expansion, or I2C-to-parallel GPIO extenders. Its multi-voltage VCCIO banks (1.5 V, 1.8 V, 2.5 V, 3.3 V) eliminate external level shifters when bridging between legacy 3.3 V MCUs and modern 1.8 V SoCs. With 118.3 MHz internal fMAX, the CPLD can sustain aggregate data throughput above 200 Mbps on wide parallel interfaces.
Önerilen
Consumer Electronics Display Control & Backplane Logic
In consumer displays and backplane controllers, the 5M570ZM100C5N handles LVDS signaling, backlight PWM, key-scan matrix decoding, and standby power gating. Its 1.8 V core plus 8 Kbits user flash memory (UFM) allow storage of device calibration constants and EDID-like parameter blocks without external EEPROM, reducing BOM. The 100-MBGA package is small enough for space-constrained TV and monitor mainboards while still exposing enough I/O for full HDMI-sideband or DisplayPort AUX channel management.
Önerilen
Automotive Aftermarket ECU Customization & Brownout-Safe Logic
Brownout-resilient control paths in automotive aftermarket ECUs benefit from the 5M570ZM100C5N's non-volatile flash configuration: bitstream is retained across cold-crank and load-dump events that would otherwise corrupt SRAM-based logic. The CPLD can implement fuel-pump relay gating, watchdog reset distribution, and CAN-bus arbitration logic that must survive supply transients without reconfiguration latency. Its 9 ns tPD enables fast hardware interlocks that are safer than software-only watchdog approaches in 12 V automotive systems.
Önerilen
Telecom Line Card Glue Logic & Clock Distribution
Telecom line-card designs use the 5M570ZM100C5N to implement TDM bus multiplexing, alarm-indicator aggregation, and clock-failover switchover between redundant PLLs. The CPLD's deterministic 9 ns tPD and 118.3 MHz fMAX meet telecom Stratum-3 timing margin requirements for hold-and-forward paths, while its multi-voltage I/O bridge cleanly between 1.8 V SERDES PHYs and 3.3 V backplane logic. The flash-based non-volatile configuration survives line-card hot-swap events without external boot logic.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: 5M570ZM100C5N — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | 5M570ZM100C4N | 5M570ZM100A5N | 5M570ZM100I5N | 5M570ZT100I5N |
|---|---|---|---|---|---|
| Package | 100-MBGA (M100, 0.5 mm pitch) | 100-MBGA (M100, 0.5 mm pitch) - same | 100-MBGA (M100, 0.5 mm pitch) - same | 100-MBGA (M100, 0.5 mm pitch) - same | 100-TQFP - DIFFERENT (cross-package) |
| Brand | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) |
| Logic Elements / Macro Cells | 440 | 440 | 440 | 440 | 440 |
| Speed Grade | C5 (118.3 MHz fMAX, ~9 ns tPD) | C4 (slower than C5) | A5 (lowest speed grade) | I5 (industrial grade, ~C5 timing) | I5 (industrial grade, ~C5 timing) |
| Operating Temperature | 0C to +85C (commercial) | 0C to +85C (commercial) | 0C to +85C (commercial) | -40C to +100C (industrial) | -40C to +100C (industrial) |
| Core Supply Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.5 / 1.8 / 2.5 / 3.3 V | 1.5 / 1.8 / 2.5 / 3.3 V | 1.5 / 1.8 / 2.5 / 3.3 V | 1.5 / 1.8 / 2.5 / 3.3 V | 1.5 / 1.8 / 2.5 / 3.3 V |
| User Flash Memory (UFM) | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits |
Ana Farklılayıcılar
- Non-volatile flash configuration eliminates external boot PROM (karşılaştırma:Xilinx XC2C512 (CoolRunner-II))
- Drop-in 100-MBGA variants across speed grades and temperature grades (karşılaştırma:5M570ZT144I5N (144-TQFP))
- Multi-voltage I/O banks eliminate external level shifters (karşılaştırma:5M40Z family (lower-density MAX V))
Tasarım Notları
Route all four GND balls of the 100-MBGA package directly to a continuous, unbroken ground plane directly under the BGA. The MAX V datasheet recommends via-in-pad or micro-via fan-out for ground balls to minimize simultaneous-switching noise (SSN) on multi-bank outputs. A split or stitched ground plane degrades the CPLD's ability to return switching currents and can introduce timing skew and ground bounce above 50 MHz parallel-bus operation.
Per the MAX V Device Handbook, decouple every VCCIO bank with a 0.1 uF X7R ceramic capacitor placed within 100 mils of the corresponding ball. Add a single 10 uF X5R bulk capacitor on VCCINT (1.8 V). The internal 3.3 V/2.5 V regulator eliminates the need for an external VCCIO rail when only the highest bank voltage is needed, but external rails are still required when driving 1.5 V or 1.8 V logic on a bank. Verify regulator current budget against the I/O bank load before relying on the internal LDO.
Do not assume the 5M570ZM100C5N, 5M570ZM100C4N, and 5M570ZM100I5N are interchangeable without re-running Quartus timing analysis. Although all three share the same 100-MBGA ballmap and 440 macro cells, their speed grades differ; a design that meets timing at C5 grade may fail timing closure at C4 or A5 grade. Also, the I-grade part adds an industrial temperature range that affects tCO and tSU timing parameters. Always verify the design's worst-case fMAX and tPD against the chosen speed-grade datasheet.
Uyumluluk Bilgisi
RoHS and lead-free compliant per Altera / Intel PSG product page. Commercial temperature grade (0C to +85C); not AEC-Q100 qualified for automotive - choose the 5M570ZM100I5N industrial variant (-40C to +100C) for harsh-environment applications. Halogen-free status not explicitly stated in the verified web data.
