KSZ8031RNL - 10/100 Ethernet PHY | Microchip Technology
MPN: KSZ8031RNL ✓ AktifKSZ8031RNL Genel Bakış
An Ethernet physical layer transceiver is the circuit that converts digital frame data from an Ethernet media access controller into signals suitable for twisted-pair cabling, then converts received cable signals back into digital data. This PHY belongs to the hierarchy Ethernet transceiver > physical layer device > network interface IC > semiconductor. RMII provides a standardized parallel connection between the PHY and a compatible Ethernet processor or switch.
The KSZ8031RNL supports both 10Base-T and 100Base-TX operation, allowing one physical-layer design to serve legacy 10 Mb/s and Fast Ethernet 100 Mb/s links. Its full-duplex RMII interface supports simultaneous transmit and receive activity, while single-supply operation simplifies system power design. The 24-QFN package also supports space-constrained embedded networking designs.
Compared with the related KSZ8021RNL, the KSZ8031RNL uses the RMII reference-clock arrangement suited to systems requiring a 25 MHz reference. The RMII interface exposes the PHY connections required for data, control, carrier sense, and clock signaling between the transceiver and Ethernet MAC. The manufacturer documentation also identifies the device as a direct-interface physical layer rather than a complete Ethernet controller.
Typical uses include industrial Ethernet equipment, embedded control systems, IP cameras, network switches, serial-to-Ethernet products, and compact data-acquisition devices. The device is particularly appropriate when a host processor already includes an RMII-compatible Ethernet MAC and the PCB area is limited.
Design the PCB with the 24-QFN footprint, power and decoupling capacitors, a 50 MHz differential clock arrangement, and an RMII interface routed according to the manufacturer datasheet. Confirm PHY address, strap configuration, magnetics, termination, and cable-side layout before releasing the design.
This product page combines the manufacturer electrical description, package information, application guidance, replacement cross-checks, and PCB-focused design considerations to support faster component selection and implementation.
Drop-in alternatifler için KSZ8031RNL — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller KSZ8031RNL (aynı form faktörü ve ayağa oturma) — farklı olan Package, Product Type, Cable Type, Ethernet Speed Support, Interface.
KSZ8021RNL
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8031RNLI
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
KSZ8081RNACA-TR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8031RNL Özellikler
| Product Type | 10Base-T/100Base-TX Ethernet physical layer transceiver |
| Ethernet Speed Support | 10 Mb/s and 100 Mb/s |
| Besleme Gerilimi | 3.3 V |
| Arayüz | Reduced Media Independent Interface (RMII) |
| Duplex Mode | Full duplex |
| Cable Standard | CAT-5 unshielded twisted pair (UTP) |
| Port Count | 1 port |
| Paket | 24-QFN (4 x 4 mm) |
| Montaj Türü | Surface mount |
| RMII Reference Clock | 25 MHz |
| Media Interface | 10Base-T/100Base-TX |
| Data Link Standard | Ethernet |
| Evaluation Board | KSZ8031RNL-EVAL |
KSZ8031RNL 24-qfn (4 x 4 mm) Pin Yapısı Kılavuzu
KSZ8031RNL (24-qfn (4 x 4 mm) paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: KSZ8031RNL.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
KSZ8031RNL için uygundur 6 uygulamas: Industrial Ethernet Control, Embedded Network Gateway, IP Camera Connectivity, Compact Network Switch, Data Acquisition Terminal, Networked Test Equipment.
Industrial Ethernet Control
The KSZ8031RNL suits industrial controllers that require a single 10/100 Ethernet port and already provide an RMII-compatible MAC. Its support for both 10Base-T and 100Base-TX allows the controller to negotiate common industrial network speeds without adding a separate physical-layer device. Full-duplex operation supports simultaneous control traffic and data transfer, while the 24-QFN footprint preserves board area in compact DIN-rail or embedded systems. The design must include suitable Ethernet magnetics, isolation components, 3.3 V decoupling, and a controlled 25 MHz RMII reference clock. Cable-side layout should follow the manufacturer application guidance to maintain differential signal integrity and reliable network attachment.
Önerilen
Embedded Network Gateway
The KSZ8031RNL adds wired Ethernet connectivity to an embedded gateway when the host processor already contains an RMII MAC. The device handles 10 Mb/s and 100 Mb/s operation over CAT-5 UTP, making it suitable for configuration ports, service interfaces, and local supervisory networks. Its 24-QFN package helps reduce connector-adjacent routing congestion in compact gateway boards. Designers should budget for an Ethernet transformer or integrated magnetics, magnetic-field spacing, chassis or board grounding strategy, and low-ESR supply decoupling. The RMII timing path also requires short, length-matched routing because the 25 MHz clock and associated data signals must meet the manufacturer interface requirements.
Önerilen
IP Camera Connectivity
The KSZ8031RNL can provide the wired 10/100 Ethernet physical layer for an IP camera whose base processor includes an RMII-compatible MAC. Supporting both 10Base-T and 100Base-TX is useful during installation on older network segments while allowing higher throughput where available. The full-duplex interface supports continuous image traffic, and the small 24-QFN package is suitable for space-constrained camera electronics. The PCB should keep the PHY, magnetics, RJ45 interface, and digital host interface in a controlled layout with a clean separation between analog and digital return currents. Verify thermal performance around the exposed pad and provide the specified local bypass capacitance near the supply pins.
Önerilen
Compact Network Switch
The KSZ8031RNL can implement a copper Ethernet port in a compact switch or interface module whose switching fabric or host controller offers an RMII-compatible endpoint. Its 24-QFN package supports dense port layouts, while full-duplex 10/100 operation supports legacy edge ports and control-plane traffic. The single-supply 3.3 V architecture simplifies rail planning where the surrounding switch logic already operates at compatible levels. Placement of the PHY close to its magnetics reduces differential trace length and helps separate the high-energy cable-side network from the RMII domain. Designers should consult the manufacturer datasheet for strap settings, LED behavior, clock requirements, power sequencing, and the recommended magnetics implementation.
Önerilen
Data Acquisition Terminal
The KSZ8031RNL is appropriate for data-acquisition equipment that needs to publish measurements over 10/100 Ethernet while using an RMII-capable embedded controller. Fast Ethernet mode provides sufficient bandwidth for typical control, logging, and telemetry traffic, while 10Base-T support improves interoperability with older laboratory and plant networks. The small 24-QFN package leaves board area for analog front ends and connectors. Critical implementation work includes isolating the cable-side magnetics from sensitive measurement circuitry, controlling ground returns, and providing stable 3.3 V power with local high-frequency bypass. Validation should cover link negotiation, RMII timing, packet-loss behavior, and operation with the intended CAT-5 cable installation.
Önerilen
Networked Test Equipment
The KSZ8031RNL can add a 10/100 Ethernet service port to test and measurement equipment whose controller includes an RMII interface. The device supports both common Ethernet rates, enabling remote control, status reporting, and firmware delivery over existing copper networks. Its full-duplex operation suits continuous data transfer, and the compact 24-QFN package fits front-panel or internal communication boards. Use short RMII routing and controlled impedance or matched-length treatment where required by the interface specification, while placing magnetics and protection components near the connector. Chassis grounding and surge or ESD protection must be coordinated so that user-accessible cable interfaces do not introduce excessive coupling into the measurement circuitry.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: KSZ8031RNL — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | KSZ8021RNL | KSZ8031RNLI | KSZ8081RNACA |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-QFN (4 x 4 mm) | 24-QFN (4 x 4 mm) | 24-QFN (4 x 4 mm) | 24-VFQFN |
Ana Farklılayıcılar
- Matches the 25 MHz RMII reference arrangement (karşılaştırma:KSZ8021RNL)
- Uses the same compact 24-QFN footprint (karşılaştırma:KSZ8031RNLI)
- Documented as a complete replacement (karşılaştırma:KSZ8081RNACA)
Tasarım Notları
Place the KSZ8031RNL close to the Ethernet transformer and connector, while keeping the RMII side toward the host processor. Route the cable-side differential pairs as short, continuous pairs with symmetric geometry and a continuous reference plane. Maintain the manufacturer-specified separation from the exposed pad, supply components, and clock circuitry to reduce radiated emissions and susceptibility to cable-borne interference.
Implement the single 3.3 V supply on the PCB with local high-frequency bypass at the PHY supply pins and adequate bulk capacitance near the power entry point. Keep switching-regulator and inductor placement away from the Ethernet magnetics and cable-side traces. Confirm power-on sequencing and the allowable ramp condition in the manufacturer datasheet, particularly when the host processor and PHY share a reset-controlled supply.
Route the 25 MHz RMII reference clock and associated data signals on a continuous ground plane, with short point-to-point connections and no stubs. Check source-synchronous timing, clock skew, trace length, and load assumptions against the manufacturer interface specifications. Avoid placing test pads or unnecessary vias in clock-sensitive paths, and keep unrelated switching nodes away from the RMII region.
Do not substitute KSZ8021RNL without checking its 50 MHz RMII reference-clock requirement against the KSZ8031RNL's 25 MHz arrangement. Likewise, verify every configuration strap, LED connection, PHY address, and exposed-pad connection when using KSZ8031RNLI or KSZ8081RNACA. Package similarity alone does not confirm timing, thermal, or configuration compatibility.
Uyumluluk Bilgisi
The interface circuit is not an automotive-qualified device; RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product declaration or product page.
