LM25011MYX/NOPB - 42V 2A Buck Regulator | Texas Instruments
MPN: LM25011MYX/NOPB ✓ AktifLM25011MYX/NOPB Genel Bakış
A buck converter, or step-down regulator, is a DC-DC switching converter that efficiently reduces a higher input voltage to a lower regulated output using a switching element and an LC filter. Unlike linear regulators, buck converters achieve high efficiency even at large input-to-output voltage differences, making them fundamental building blocks in power management IC hierarchies. The LM25011 belongs to the constant on-time regulator family, which regulates by controlling the high-side switch on-time without requiring loop compensation.
Key features include the 6V to 42V input operating range with 45V absolute maximum rating, adjustable output from 2.51V to 40V, and 2A load capability. The COT control scheme provides fast transient response with no external compensation network. An adjustable current limit, set via an external resistor, lets designers tailor the peak switch current, while thermal shutdown protects against fault conditions.
Technically, the on-time is inversely proportional to input voltage, keeping switching frequency nearly constant across the input range. The internal high-side N-channel MOSFET minimizes conduction losses, and a precision feedback comparator ensures accurate regulation up to 2 MHz operation per datasheet specifications.
Typical applications include industrial power supplies, automotive bias rails (with the AEC-Q100 qualified LM25011-Q1 variant), telecom equipment, and 12V/24V distributed bus point-of-load conversion powering microcontrollers and sensors.
Design tip: select the inductor and output capacitor per the datasheet design equations, set the current limit resistor above maximum load current, and use short PCB traces with solid ground planes to minimize parasitic inductance.
Drop-in alternatifler için LM25011MYX/NOPB — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM25011MYX/NOPB (aynı form faktörü ve ayağa oturma) — farklı olan Current Limit, Operating Temperature, Output Voltage Range, Package, Topology.
LM25011Q1MYX/NOPBQ1
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM25011QMYX/NOPBQ1
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM25011AMYX/NOPB
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM25011A-Q1MYX/NOPB
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM25011MMX/NOPB
⚡ Aynı Paket ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM25011MYX/NOPB Maksimum Değerlendirmeler & Elektriksel Özellikler
| Ağ Yapısı | Step-Down (Buck), Constant On-Time |
| Giriş电压范围 | 6 V to 42 V |
| Absolute Maximum Input Rating | 45 V |
| Çıkış Gerilimi Aralığı | 2.51 V to 40 V (adjustable) |
| Output Current | 2 A |
| Çıkış Sayısı | 1 |
| Değiştirme Frekansı | Up to 2 MHz |
| Control Scheme | Constant On-Time (COT), no loop compensation required |
| 同步整流器 | No |
| Akım Sınırı | Adjustable via external resistor |
| Integrated Switch | N-Channel Buck switch |
| İşletim Sıcaklığı | -40C to +125C |
| Paket | HVSSOP (DGQ), 10 pins, 3 mm x 4.9 mm |
| Montaj Türü | Surface Mount |
| Automotive Qualification | LM25011-Q1 variant is AEC-Q100 Grade 1 qualified |
| Protection Features | Thermal shutdown, adjustable current limit, startup regulator |
LM25011MYX/NOPB Pin Yapısı
| Pin 1 | VIN — Input supply, 6V to 42V operating range |
| Pin 2 | SS — Soft-start programming pin |
| Pin 3 | FB — Feedback input from output voltage divider (1.252V reference) |
| Pin 4 | AGND — Analog ground reference |
| Pin 5 | CS — Current limit sense input, sets adjustable current limit via external resistor |
| Pin 6 | PGND — Power ground for switch current return |
| Pin 7 | RT — On-time control resistor, sets switching frequency |
| Pin 8 | SW — Switch node - drain of internal N-channel buck switch |
| Pin 9 | SW — Switch node (paralleled) |
| Pin 10 | SD — Shutdown / enable control pin |
| Pin EP | Exposed Pad — Ground and thermal dissipation path, must be soldered to PCB copper |
Tipik Uygulamalar
LM25011MYX/NOPB için uygundur 6 uygulamas: Industrial 24V Bus Point-of-Load Power, Automotive Bias and Auxiliary Rails, Telecom and Networking Equipment, Battery-Powered Portable Instruments, LED Driver and Lighting Power Supplies, Distributed Microcontroller and Sensor Supplies.
Industrial 24V Bus Point-of-Load Power
Industrial control systems commonly distribute 24V power, and the LM25011MYX/NOPB converts this directly to 5V or 3.3V logic rails at up to 2A without a pre-regulation stage. Its 42V input rating gives headroom above 24V nominal bus transients, and the constant on-time scheme requires no external loop compensation, reducing BOM cost in high-volume PLC and sensor-hub designs. Place the regulator near the load with a compact power stage; the integrated N-channel switch keeps efficiency high while the adjustable current limit can be sized to the specific rail, avoiding overdesign.
Önerilen
Automotive Bias and Auxiliary Rails
With the AEC-Q100 Grade 1 qualified LM25011-Q1 variant, this regulator family serves automotive auxiliary supplies from 12V or 24V battery buses, powering ECUs, body electronics, and sensor modules. The 45V absolute maximum input absorbs load-dump-adjacent transients in clamped systems, and -40C to +125C junction operation covers underhood and exterior module environments. Because the Q1 variant is pin-to-pin identical to the commercial part, automotive and non-automotive builds can share one PCB layout, simplifying dual-market designs and reducing qualification effort.
Önerilen
Telecom and Networking Equipment
Telecom infrastructure distributes -48V-derived or 24V intermediate buses, and the LM25011's 6-42V input range and up to 2 MHz capability enable compact, fast-transient buck bias supplies for line cards, DSL modems, and network interface boards. The constant on-time control delivers quick load-transient response without compensation networks - important when rails step-load into processors or PHYs. The adjustable current limit protects against shorted outputs on hot-swappable cards, and the exposed-pad HVSSOP-10 dissipates heat efficiently in convection-cooled rack equipment.
Önerilen
Battery-Powered Portable Instruments
Portable test instruments and field devices powered by 12V-36V battery packs (lead-acid, Li-ion stacks) use the LM25011MYX/NOPB to generate regulated low-voltage rails efficiently. Wide input tolerance accommodates battery voltage sag and charge-voltage swing without external preregulation, and the COT architecture maintains good light-load behavior for battery-operated duty cycles. Up to 2 MHz operation permits small inductors, shrinking power-stage size for handheld enclosures, while the integrated switch and thermal shutdown simplify safety review for consumer-adjacent designs.
Önerilen
LED Driver and Lighting Power Supplies
Constant on-time buck topology adapts well to LED bias supplies, and the LM25011's wide 6-42V input covers 12V/24V LED strip and fixture systems. The adjustable current limit supports peak-current-controlled LED drive approaches, and operation up to 2 MHz allows switching above the audible band, avoiding acoustic noise in lighting fixtures. Designers typically regulate LED current by sensing it in the FB path; the device's fast comparator gives responsive dimming behavior. Thermal shutdown provides a fail-safe for enclosed fixtures with limited airflow.
Önerilen
Distributed Microcontroller and Sensor Supplies
Board-level bias for MCUs, ADCs, and sensors in measurement systems relies on clean, well-regulated local rails. The LM25011MYX/NOPB converts a higher intermediate bus to 3.3V or 5V at up to 2A, and its fast COT transient response supports the step loads of microcontrollers entering and exiting sleep modes. Because it is nonsynchronous with adjustable current limit, designers can safely power crowbar-protected analog sections. Pair with an LDO or ferrite filter for noise-sensitive analog rails in precision data-acquisition chains.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM25011MYX/NOPB — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM25011Q1MYX/NOPBQ1 | LM25011AMYX/NOPB | LM25011MMX/NOPB |
|---|---|---|---|---|
| Package | HVSSOP-10 (DGQ) 3x4.9 mm | HVSSOP-10 (DGQ) - same | HVSSOP-10 (DGQ) - same | MSOP-10 (no power pad) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Voltage Range | 6 V to 42 V | 6 V to 42 V | 6 V to 42 V | 6 V to 42 V |
| Output Current | 2 A | 2 A | 2 A | 2 A |
| Output Voltage Range | 2.51 V to 40 V | 2.51 V to 40 V | 2.51 V to 40 V | 2.51 V to 40 V |
| Automotive Grade (AEC-Q100) | No | Yes (Grade 1) | No | No |
| Low-Dropout High-Frequency Operation | No (standard version) | No | Yes | No |
| Thermal Performance | Exposed power pad (best in family) | Exposed power pad | Exposed power pad | No power pad - higher theta_JA |
Ana Farklılayıcılar
- Exposed power pad HVSSOP package (karşılaştırma:LM25011MMX/NOPB)
- Automotive AEC-Q100 Grade 1 drop-in option (karşılaştırma:LM25011Q1MYX/NOPBQ1)
- Integrated solution minimizes external parts (karşılaştırma:LM5117PMH/NOPB)
- No loop compensation required (karşılaştırma:LM25011AMYX/NOPB)
Tasarım Notları
The HVSSOP-10 (DGQ) exposed pad is the primary heat-removal path for the LM25011. Solder the exposed pad to a grounded copper pour of at least 4-6 via-connected square centimeters; a floating or poorly soldered pad dramatically raises junction temperature at 2A loads from high input voltages. Estimate dissipation as P = Iout^2 x Rds(on) + switching losses plus diode loss, and verify junction temperature stays below 125C at worst-case ambient per the datasheet thermal table.
Keep the SW node, input capacitor, and freewheeling diode loop as small as possible - this high-di/dt loop dominates EMI. Place the input ceramic capacitor within a few millimeters of VIN and PGND, route FB and CS traces away from the switch node, and use the exposed pad as a low-inductance ground reference. Follow the PCB layout example in the TI LM25011 datasheet section on application information for proven component placement.
Set the current-limit resistor on the CS pin above the maximum peak inductor current (load current plus half the ripple), but below the inductor saturation rating - account for tolerance and temperature. Choose the RT on-time resistor so switching frequency stays in the intended range across the 6-42V input, since on-time is inversely proportional to VIN. Use the datasheet design equations rather than copying values between designs, as optimum inductance depends on VIN, VOUT, and frequency.
Never exceed the 45V absolute maximum input rating; add a TVS or input clamp in automotive or industrial environments with load-dump or surge exposure. Do not use the standard LM25011 where duty cycle approaches 100% at high frequency - select the LM25011A variant, which permits low-dropout operation. Also ensure the freewheeling diode is a fast Schottky rated for peak switch current and reverse voltage, not a standard-recovery rectifier.
Uyumluluk Bilgisi
NOPB suffix indicates No Pull of Bare - lead-free/RoHS-compliant TI packaging convention. AEC-Q100 applies only to the LM25011-Q1 variants, not this commercial part.
