LM2900NG4 Quad Norton Op Amp | 14-PDIP | Texas Instruments
MPN: LM2900NG4 ✓ AktifLM2900NG4 Genel Bakış
A Norton operational amplifier is a current-buffer amplifier architecture rather than a conventional voltage-input amplifier. Its input signal is represented as a current, which allows the amplifier to operate with relatively low input bias current and can be useful in sensor interfaces, current-feedback signal paths, and feedback networks. The LM2900 family combines four amplifiers in one package, reducing board area and simplifying multi-channel analog designs where several similar signal-processing stages are required.
The principal application features are its quad amplifier organization, high gain, internal frequency compensation, and single-supply capability. Frequency compensation allows each amplifier to be used as a stable gain stage without requiring an external compensation network in many standard closed-loop configurations. The wide operating supply range supports industrial, instrumentation, audio, control, and embedded analog systems where the supply voltage is not tightly constrained.
The LM2900NG4 uses a 14-pin PDIP package with through-hole mounting. Through-hole construction is useful for prototypes, educational platforms, legacy control boards, industrial equipment, and repair applications where a socket or conventional PCB drilling process is preferred. The DIP-14 footprint also provides generous spacing between leads, simplifying hand assembly and inspection compared with fine-pitch surface-mount packages.
When designing around the LM2900NG4, identify the function of each amplifier section and confirm the complete pin assignment, supply requirements, input and output common-mode limits, output swing, and stability behavior in the manufacturer datasheet. Use the manufacturer datasheet for the exact pinout and application examples. Feedback resistors and compensation choices should be calculated for the intended closed-loop gain, while input and output signal paths should be kept short to reduce noise pickup and instability risk.
This product page organizes the LM2900NG4 technical profile, sourcing information, package details, practical design notes, and a comparison framework for engineers evaluating quad general-purpose op amps. It is intended to support component selection, schematic review, PCB compatibility checks, and replacement planning rather than replace the complete manufacturer datasheet.
Drop-in alternatifler için LM2900NG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM2900NG4 (aynı form faktörü ve ayağa oturma) — farklı olan Frequency Compensation, Package, Product Type.
LM2900N
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM3900N
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM2900NG4 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Number of Amplifiers | 4 |
| Amplifier Architecture | Norton current-buffer operational amplifier |
| Gain | High gain |
| Frequency Compensation | Internally compensated |
| Product Type | General-purpose operational amplifier |
| Supply Configuration | Single supply or split supply |
| Paket | 14-pin PDIP |
| Montaj Türü | Through-hole |
| Pin Sayısı | 14 pins |
| Supplier Description | Standard general-purpose amplifier, 4 circuit, 14-PDIP |
| Application Category | Linear amplifier, buffer amplifier, instrumentation amplifier |
LM2900NG4 14-pin pdip Pin Yapısı Kılavuzu
LM2900NG4 (14-pin pdip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM2900NG4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM2900NG4 için uygundur 6 uygulamas: Sensor Signal Conditioning, Industrial Control Signal Conditioning, Audio Preamp and Buffering, Data Acquisition Front End, Legacy Interface Buffering, Power Supply Monitoring.
Sensor Signal Conditioning
The LM2900NG4 is suitable for conditioning low-frequency sensor signals when the circuit requires multiple amplification or buffering channels. Its four high-gain, internally compensated Norton amplifiers can form gain stages, impedance adapters, or difference-stage building blocks within a shared supply domain. The main engineering checks are input bias current relative to sensor source impedance, common-mode range, output swing, and closed-loop stability at the intended gain. Because each channel is independent, engineers can assign similar conditioning paths to several sensors while simplifying decoupling and grounding. The manufacturer LM2900 datasheet should be used to verify the complete pin mapping and electrical limits before schematic release.
Önerilen
Industrial Control Signal Conditioning
The LM2900NG4 fits legacy and industrial control boards that need several general-purpose analog amplification channels from one package. A typical implementation can use one channel for command conditioning, another for feedback amplification, and the remaining channels for transducer or interface signals. Its single-supply or split-supply capability supports broad control-system architectures, while the DIP-14 footprint is convenient for through-hole boards and socketed maintenance assemblies. Verify industrial temperature grade, supply limits, output loading, and electromagnetic robustness in the exact manufacturer datasheet, because the package and amplifier topology alone do not establish regulatory or system qualification.
Önerilen
Audio Preamp and Buffering
The LM2900NG4 can provide low-frequency gain and buffering for audio preamplifier, mixer, and active-filter circuits that do not require rail-to-rail inputs or outputs. Four amplifier sections allow a board to implement several similar signal paths, reducing package count and keeping supply routing consistent. The design should be checked against the required output swing, load impedance, closed-loop bandwidth, and distortion objectives at the actual signal level. Common-mode headroom is especially important when processing a centered audio waveform from a single supply. Use the LM2900 datasheet typical-application information to establish a stable feedback network and adequate output-current margin for the intended speaker-line or buffer load.
Önerilen
Data Acquisition Front End
The LM2900NG4 is applicable to the analog front end of a low-speed data-acquisition system requiring several gain or buffer channels. Its four independently compensated Norton amplifiers can amplify sensor outputs before multiplexing or conversion, while the through-hole package simplifies prototype construction and replacement. Design checks should include signal bandwidth, input offset relative to the least-significant converted bit, bias current at the source impedance, output settling, and available common-mode range. The quad arrangement can also reduce duplicated feedback networks, but each amplifier still requires its own stability-appropriate feedback values. Confirm channel independence, supply decoupling, and grounding in the manufacturer datasheet and final schematic review.
Önerilen
Legacy Interface Buffering
The LM2900NG4 is a practical choice for maintaining legacy instrumentation interfaces that use four buffered or amplified analog channels. Its internally compensated amplifier sections simplify stable feedback design, while the 14-pin PDIP package supports repair of older through-hole boards without introducing a fine-pitch footprint migration. The implementation must preserve the original channel polarity, reference level, and impedance expectations. Engineers should compare the original and candidate data sheets for common-mode voltage, output swing, source and sink current, and behavior near the supply rails. If the replacement changes gain-bandwidth behavior or bias characteristics, validate the complete analog path rather than relying only on continuity checks.
Önerilen
Power Supply Monitoring
The LM2900NG4 can serve as a quad amplifier in monitoring and control circuitry that compares or scales several voltage-related signals. Its high-gain Norton architecture is useful in feedback networks where the design intentionally uses current-mode signal relationships. Suitable monitoring tasks include generating scaled representations of supply rails or conditioning signals for comparators, provided the signals remain inside the amplifier input common-mode range. Because output current, output swing, offset, and supply requirements are circuit-critical, engineers must use the LM2900 family datasheet rather than infer limits from a generic op-amp table. Add local supply bypassing and maintain short feedback paths to reduce sensitivity to switching-node noise.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM2900NG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2900N | LM3900N |
|---|---|---|---|
| Manufacturer | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Number of Amplifiers | 4 | 4 | 4 |
| Architecture | Norton current-buffer operational amplifier | Norton current-buffer operational amplifier | Norton current-buffer operational amplifier |
| Supply Configuration | Single supply or split supply | Single supply or split supply | Single supply or split supply |
| Mounting Style | Through-hole | Through-hole | Through-hole |
Ana Farklılayıcılar
- Four independent amplifier channels in one DIP-14 package (karşılaştırma:LM2900N)
- Norton current-buffer architecture with internal frequency compensation (karşılaştırma:LM3900N)
- Through-hole 14-pin PDIP simplifies legacy PCB compatibility (karşılaştırma:LM3900N)
Tasarım Notları
Do not substitute the LM2900NG4 solely because another quad op amp uses a PDIP outline. Verify the numbered pin assignment, supply connections, input common-mode range, output swing, output-current capability, and stability at the intended closed-loop gain. A footprint-compatible package can still be electrically incompatible, particularly when the original circuit relies on Norton current-feedback behavior.
Place the supply bypass capacitor close to the device supply pins and route the power loop without crossings through sensitive input or feedback traces. Keep each amplifier's feedback network compact and connect its return directly to the device ground reference. Because the LM2900 family is a Norton current-buffer amplifier family, preserve the feedback topology shown in the manufacturer typical-application circuits rather than substituting a generic voltage-feedback compensation pattern.
Design each channel for the required output load and signal amplitude before fixing the supply voltage. Check both output sourcing and sinking capability, and confirm that the desired output waveform remains within the datasheet swing limits at the selected supply. For low-frequency battery-powered designs, also evaluate quiescent consumption because a four-amplifier package can consume supply current even when only one channel is active.
Use the complete manufacturer pinout for the PDIP package when assigning schematic symbols and PCB nets. Do not infer a pin from the visible channel order on another package, and do not omit shared supply pins when adapting a third-party symbol. Validate the assembled board by checking continuity from every numbered lead to the intended amplifier section and confirming that no adjacent output or input net is reversed.
Uyumluluk Bilgisi
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement for LM2900NG4 appears in the available product records. AEC-Q100 is not applicable to this general-purpose operational amplifier.