LM2904PS-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
MPN: LM2904PS-MAND ✓ AktifLM2904PS-MAND Genel Bakış
An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. High-gain internal stages, negative feedback, and an output stage convert a small differential input into an amplified output. The dual format provides two amplifiers in one package, allowing a design to implement gain stages, buffers, comparators, active filters, or instrumentation circuits while reducing board area.
The LM2904 family is specified for general-purpose signal conditioning rather than low-noise precision or high-speed applications. Its two-amplifier configuration supports complementary inverting and non-inverting paths within a single board footprint. The 26 V supply rating supports operation from conventional dual-supply rails used in industrial control, analog instrumentation, and educational electronics, while the 700 kHz gain-bandwidth figure defines its small-signal bandwidth capability.
Typical uses include audio preamplifier stages, sensor-conditioning front ends, active filters, DC amplifiers, and general laboratory instrumentation. The dual channel also allows one amplifier to provide gain while the other performs buffering or feedback-path functions. Because the device is a general-purpose part, input-common-mode range, output-swing limits, input-offset voltage, input-bias current, noise characteristics, and slew rate should be checked against the circuit requirements before layout begins.
When implementing the LM2904PS-MAND, place bypass capacitors close to the supply pins, route feedback traces away from noisy input paths, and provide stable reference and feedback networks. The 8-pin SO package permits straightforward PCB assembly and standard surface-mount inspection. Bulk packing makes the device suitable for production runs that do not require reel-fed component handling.
This page consolidates the manufacturer product information, device-ordering details, package data, cross-reference candidates, application guidance, and PCB-level design notes into one engineering-focused reference for evaluating the LM2904PS-MAND.
Drop-in alternatifler için LM2904PS-MAND — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM2904PS-MAND (aynı form faktörü ve ayağa oturma) — farklı olan Amplifier Type, Package, Slew Rate.
LM2904PS
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM2904BPS
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM2904DR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DE4
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904BDR
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM2904PS-MAND Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Package Type | 8-pin SO |
| Montaj Türü | Surface mount |
| Manufacturer | Texas Instruments |
| Ordering Code | MAND |
LM2904PS-MAND 8-pin so Pin Yapısı Kılavuzu
LM2904PS-MAND (8-pin so paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM2904PS-MAND.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM2904PS-MAND için uygundur 6 uygulamas: General-Purpose Audio Preamplifier, Sensor Signal Conditioning, Active Audio Filter, Industrial Control Interface, Voltage Buffer Stage, Test and Measurement Front End.
General-Purpose Audio Preamplifier
The LM2904PS-MAND is suitable for a two-stage audio preamplifier because one 8-pin package provides two general-purpose amplifier circuits. A non-inverting or inverting gain stage can be followed by a buffer, giving the circuit a compact footprint while retaining the family's 26 V maximum supply rating. The 700 kHz gain-bandwidth figure covers low-frequency audio and many general instrumentation signals, although the design must keep the closed-loop bandwidth below that limit. Resistor and capacitor selection should also account for the amplifier's offset and bias-current behavior, which directly influence low-level audio headroom and DC offset.
Önerilen
Sensor Signal Conditioning
The dual amplifier in the LM2904PS-MAND can condition a sensor output by combining a gain stage with a reference buffer or active feedback network. Its 26 V supply capability is useful when the transducer and downstream circuitry operate from a conventional industrial rail, while the two independent channels reduce board space compared with two separate single-amplifier packages. The 700 kHz gain-bandwidth product is appropriate for many temperature, pressure, and position sensors whose signals vary well below that frequency. Before finalizing the circuit, verify that the sensor output remains inside the amplifier's input common-mode range and that the selected feedback resistors keep the output within its swing limits.
Önerilen
Active Audio Filter
The LM2904PS-MAND can implement a two-amplifier active filter when the signal bandwidth is consistent with the device's 700 kHz gain-bandwidth product. One channel may provide amplification and the other may implement an RC feedback network for low-pass or band-pass response. Because both amplifiers share one 8-pin SO package, the circuit benefits from matched placement and short feedback paths. Component tolerances and the amplifier's open-loop gain and offset characteristics directly influence filter accuracy, so a SPICE model and measured response should be used during development. Keep the filter operating well below the amplifier's gain-bandwidth limit to avoid phase errors and unintended oscillation.
Önerilen
Industrial Control Interface
The LM2904PS-MAND can condition low-level control signals in industrial equipment when the interface is not precision critical. Its dual configuration supports one channel for signal amplification and another for buffering a feedback or reference node. The 26 V supply rating accommodates common industrial supply arrangements, and the 8-pin SO package is suitable for automated board assembly. The design must still account for the amplifier's input offset, bias current, common-mode limits, and output swing. Separate analog and digital return paths in the layout to prevent switching currents from entering the high-impedance input and feedback nodes.
Önerilen
Voltage Buffer Stage
A single LM2904PS-MAND channel can provide a unity-gain buffer ahead of an ADC, relay driver, or subsequent instrumentation stage, while the second channel handles gain or offset correction elsewhere on the board. Buffering prevents the source impedance from loading the sensor or divider network, and the dual package keeps both analog functions close together for cleaner routing. The 700 kHz gain-bandwidth product provides ample margin for slow control signals, but stability with capacitive loading must be checked using the manufacturer's stability guidance. Place the buffer output close to the receiving circuit and keep the feedback connection short.
Önerilen
Test and Measurement Front End
The LM2904PS-MAND is useful in educational and general-purpose laboratory circuits where two buffered or amplified channels are required. One amplifier can condition the source under test while the other buffers the reference input, enabling differential-style measurements with a common 8-pin SO footprint. The 26 V supply rating and 700 kHz bandwidth suit many low-frequency laboratory signals. Calibration performance will depend on offset voltage, bias current, and drift, which must be read from the manufacturer datasheet before claiming precision. For metering applications, connect the instrument ground and signal ground carefully to prevent ground-potential differences from being amplified.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM2904PS-MAND — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2904PS | LM2904BPS | LM2904DR | LM2904DE4 | LM2904BDR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO |
| Number of Amplifiers | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Product Classification | Standard general-purpose amplifier | Standard general-purpose amplifier | General-purpose amplifier, revised family | General-purpose amplifier | General-purpose amplifier, enhanced ordering suffix | General-purpose amplifier, revised family |
| Ordering Suffix | MAND bulk ordering code | PS | BPS | DR | DE4 | BDR |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Ana Farklılayıcılar
- Direct ordering match for LM2904PS designs (karşılaştırma:LM2904PS)
- Bulk-oriented MAND ordering configuration (karşılaştırma:LM2904DR)
- Dual general-purpose channels in one package (karşılaştırma:TS974IDT)
Tasarım Notları
Place a local bypass capacitor at the supply pins and connect the supply return directly to the package ground pins. Keep the supply trace short and use a solid ground plane beneath the device. Because the maximum supply rating is 26 V, verify transient overshoot at the pins rather than relying only on the nominal rail voltage. Do not exceed the absolute maximum supply rating under startup, load release, or inductive-kick conditions.
Assign the 8-pin SO footprint by following the manufacturer package drawing rather than assuming a generic SOIC outline. Confirm lead pitch, body dimensions, and land pattern during PCB library creation. The MAND ordering option is presented in bulk, so the assembly process must include a controlled incoming-inspection and soldering sequence for parts that are not supplied in standard tape-and-reel packaging.
Route the inverting-input and feedback traces as short as practical and keep them away from supply-current paths and switching nodes. Connect each input source to its amplifier pin through a defined reference point rather than a long shared trace. The two amplifier sections are independent, but their shared supply pins can couple noise between channels, so maintaining separate local decoupling branches helps preserve channel-to-channel isolation.
Do not treat the 700 kHz gain-bandwidth figure as the usable closed-loop bandwidth at every gain. Higher closed-loop gains reduce available bandwidth, and large capacitive loads can affect stability. Check the gain plan, load impedance, and output-stage limits in the manufacturer documentation before the first power-up. Also verify that the input common-mode voltage and intended output level remain inside the device's operating limits.
Uyumluluk Bilgisi
Compliance declarations were not identified in the manufacturer or distributor product information. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status with Texas Instruments using the MAND ordering code.