PI7C9X119SLFDEX PCIe-to-PCI Bridge | Diodes Incorporated
MPN: PI7C9X119SLFDEX ✓ AktifPI7C9X119SLFDEX Genel Bakış
A PCI Express-to-PCI bridge is an interface controller that adapts the serial point-to-point PCIe architecture to the parallel, shared-bus PCI specification. PCIe links use high-speed serial differential pairs, whereas a legacy PCI bus carries multiple parallel address and data signals. A reversible bridge is designed to support the bridge relationship in either system direction rather than functioning as a simple endpoint or repeater. This makes the device relevant to embedded, industrial, communication, and legacy-expansion platforms that must retain PCI equipment while adopting a PCIe host interface.
The PI7C9X119 series is identified as a PCIe 2 six-port, eight-lane packet switch in the ExtremeLo family. Six ports and eight lanes provide the switching resources required to organize traffic between a PCIe system interface and PCI-facing resources. Reversible operation adds topology flexibility, allowing the same bridge silicon to be evaluated in either direction of the PCIe-to-PCI connection. Designers should nevertheless confirm lane allocation, port configuration, reference-clock requirements, reset behavior, and electrical routing against the manufacturer datasheet for the specific board design.
The LQFP-128 package presents a substantial mixed-signal and high-speed implementation challenge. The design must route multiple high-speed differential pairs with controlled impedance, maintain length matching within the applicable PCIe receiver and transmitter tolerances, and provide low-noise return paths through the reference plane. The bridge also requires multiple supply rails, clocking, configuration, and peripheral interfaces, so careful partitioning of power, digital, and clock domains is essential for reliable operation.
Typical uses include industrial controller upgrades that retain PCI expansion cards, communication equipment with mixed-generation backplanes, embedded systems that interface legacy PCI peripherals to a PCIe processor module, and test or transport systems requiring a configurable PCIe-to-PCI conversion stage. Reversible operation can simplify shared platform qualification when either side of the link must act as the controlling endpoint during different product configurations.
The critical design consideration is signal integrity. Place the bridge close to the PCIe connector and connector-associated protection devices, follow the manufacturer reference layout for differential pairs, and provide the specified decoupling at every supply pin. Do not substitute generic bulk decoupling for the documented high-frequency network, and validate eye diagrams, compliance, and lane margin on the finished board.
This page consolidates interface identification, package information, related ordering codes, practical PCB guidance, and application-oriented design context. It also distinguishes functional alternatives from true pin-to-pin replacements, helping engineers make a board-level decision rather than relying only on a matching interface description.
Drop-in alternatifler için PI7C9X119SLFDEX — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
PI7C9X119SLFDE
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PI7C9X119SLFDEX Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | PCI Interface IC / PCIe-to-PCI Reversible Bridge |
| PCI Express Generation | PCIe 2 |
| Port Count | 6 ports |
| Lane Count | 8 lanes |
| Architecture | Reversible PCIe-to-PCI bridge |
| Product Family | ExtremeLo family |
| Paket | LQFP-128 |
| Montaj Türü | Surface Mount |
| Shipping Package | Tape & Reel (TR) |
| Base Product Number | PI7C9X119 |
PI7C9X119SLFDEX tape & reel (tr) Pin Yapısı Kılavuzu
PI7C9X119SLFDEX (tape & reel (tr) paket) için pin yapısı. Bu güç cihazı gate, drain ve kaynak terminal özelliklerlidir. Polarizasyonlu paketler için, doğru pin 1 yönlendirme ve ayak detayları için üretici veri kitapçığını referans alın. Orta uygulamalar arasında güç besleme tasarımı, motor kontrolü ve yük değiştirme bulunur.
Ayrıntılı pin çıkış verisi mevcut değil: PI7C9X119SLFDEX.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
PI7C9X119SLFDEX için uygundur 6 uygulamas: Industrial Controller Legacy PCI Expansion, PCIe Processor Module to Legacy Backplane, Communication Equipment Mixed-Generation Interface, PCI Express Protocol Test and Measurement, Embedded Data Acquisition with PCI Peripherals, Secure Embedded Platform PCI Expansion.
Industrial Controller Legacy PCI Expansion
The PI7C9X119SLFDEX can bridge a modern PCI Express host connection to legacy PCI expansion hardware in an industrial controller that must preserve installed cards. Its six-port, eight-lane PCIe 2 switching organization provides the interface resources for a mixed-generation backplane, while reversible operation allows the bridge topology to be evaluated in either direction. Place the device near the PCIe connector, follow the manufacturer reference layout for differential routing, and isolate legacy PCI routing from high-speed clock and data nets. This is especially valuable where fielded PCI cards must remain usable during a controller-generation upgrade.
Önerilen
PCIe Processor Module to Legacy Backplane
The PI7C9X119SLFDEX is suited to embedded platforms that use a PCIe processor or carrier module while retaining a legacy PCI backplane. The reversible bridge architecture supports flexible system roles, and the eight-lane PCIe 2 resource set can support a structured PCIe-to-PCI connection rather than simple endpoint pass-through. Board planning should allocate continuous reference planes under the high-speed pairs, control lane skew, and keep the external reference clock distribution away from switching and termination regions.
Önerilen
Communication Equipment Mixed-Generation Interface
In communication equipment, the PI7C9X119SLFDEX can connect PCIe-based processing modules to conventional PCI interface cards that remain part of a qualified platform. The six-port, eight-lane packet-switch organization gives the designer more routing options than a basic single-port bridge, while reversible operation supports shared hardware across multiple chassis configurations. Treat the legacy PCI side as a potentially noisy parallel environment, and keep its clock, termination, and connector returns separated from the low-noise PCIe power and clocking areas.
Önerilen
PCI Express Protocol Test and Measurement
The PI7C9X119SLFDEX can be evaluated inside protocol test, fault-injection, or legacy-interface test platforms that require a PCIe-to-PCI conversion stage with reversible configuration. Its packet-switch architecture provides a structured way to bridge host-side traffic to PCI resources while exercising lane behavior and bridge configuration. Use controlled reference-clock distribution and repeatable lane geometry so that measured eye diagrams and compliance results reflect the intended interconnect rather than layout variation.
Önerilen
Embedded Data Acquisition with PCI Peripherals
The PI7C9X119SLFDEX can serve as the interface between a PCIe-based data-acquisition controller and legacy PCI acquisition or processing cards. Its reversible operation allows the same bridge device to be evaluated where either the PCIe controller or PCI peripheral side must assume the system-facing role. Keep high-speed differential routing short, provide the specified per-pin decoupling, and verify clock-jitter tolerance across every operating mode. This approach preserves expensive or long-qualified PCI peripherals without redesigning the complete acquisition chassis.
Önerilen
Secure Embedded Platform PCI Expansion
Security-focused embedded platforms can use the PI7C9X119SLFDEX when certified PCI expansion cards must communicate through a PCIe fabric. The bridge keeps the legacy interface behind a defined PCIe boundary while offering reversible configuration for platform qualification and test modes. Layout and firmware should treat configuration straps, reset sequencing, and the reference clock as controlled security boundaries. Validate the finished system for correct bus ownership, error reporting, and recovery behavior before integrating production hardware.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PI7C9X119SLFDEX — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PI7C9X119SLFDE |
|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated |
| Package | LQFP-128 | LQFP-128 - same |
| Device Function | Slimline PCIe-to-PCI reversible bridge | Slimline PCIe-to-PCI reversible bridge |
| PCI Express Generation | PCIe 2 | PCIe 2 |
| Port Count | 6 ports | 6 ports |
| Lane Count | 8 lanes | 8 lanes |
| Product Family | ExtremeLo | ExtremeLo |
| Shipping Package | Tape & Reel (TR) | Tray |
| Base Product Number | PI7C9X119 | PI7C9X119 |
Ana Farklılayıcılar
- Identical electrical device with a different production shipping format (karşılaştırma:PI7C9X119SLFDE)
- Reversible PCIe-to-PCI bridge organization (karşılaştırma:Generic one-way PCIe endpoint devices)
- Purpose-built PCIe 2 packet-switch resource set (karşılaştırma:General-purpose interface adapters)
Tasarım Notları
Route PCIe differential pairs as short, continuous, impedance-controlled nets with a continuous reference plane beneath the complete route. Match the lane geometry, pair separation, and via structure to the manufacturer reference layout rather than relying on generic length matching. Avoid plane splits, test pads, and right-angle jogs in the high-speed region, then verify eye diagrams and lane margin on the assembled board.
Separate the parallel PCI bus, external reference-clock distribution, and low-noise power regions from the PCIe differential pairs. Keep the bridge close to the primary PCIe connector so protection-device and connector transitions remain short. Use the manufacturer's recommended layer stack and via fencing where specified, and provide uninterrupted return paths beneath every high-speed pair.
Implement the documented supply network and pin-specific decoupling rather than relying only on bulk bulk capacitance. Place small high-frequency capacitors directly at the associated device pins with short ground vias, and partition noisy switching or legacy-bus return currents so they do not share a path with sensitive bridge references. Validate rail sequencing and ripple at the bridge pins under full traffic load.
Do not confuse the X tape-and-reel ordering suffix with a different electrical grade, and do not treat a generic PCIe switch as a drop-in substitute without a complete pin and timing comparison. Review reset, configuration-strap, reference-clock, and firmware requirements for reversible operation. The SLFDE tray version shares the electrical base device but may not suit the same automated feeder and bulk-order workflow as SLFDEX.
Uyumluluk Bilgisi
Catalog information identifies the manufacturer, interface function, packaging, and series, but does not state the requested compliance attributes.