PIC16F737-E/SO - 20MHz 8-Bit Microcontroller | Microchip
MPN: PIC16F737-E/SO ✓ AktifPIC16F737-E/SO Genel Bakış
An 8-bit microcontroller is a programmable semiconductor that integrates a CPU, nonvolatile program memory, data memory, and peripherals on one device. PIC16F737 belongs to the PIC16 mid-range family, where a compact 14-bit instruction architecture connects directly to embedded control systems. The device hierarchy is PIC16F737 microcontroller to PIC16 mid-range MCU to 8-bit embedded microcontroller to integrated circuit and semiconductor.
The PIC16F737-E/SO provides 4K words of 14-bit Flash program memory, 368 bytes of data RAM, and up to 25 digital I/O pins. Its 11 ADC channels support 10-bit measurements, while three timers and three Capture/Compare/PWM functions support timing, waveform generation, and motor-control tasks. The synchronous serial port can operate as 3-wire SPI or 2-wire I2C, and the USART supports asynchronous serial communication.
The 20 MHz operating speed gives embedded firmware enough processing margin for sensor acquisition, protocol handling, state-machine control, and production firmware. The -E ordering designation identifies an automotive temperature grade, supporting deployments where extended environmental exposure is relevant. The -SO package code denotes a 28-pin SOIC configuration suitable for conventional PCB assembly and through-hole board layouts.
Typical uses include industrial sensor controllers, motor and actuator interfaces, instrumentation, serial protocol bridges, automotive control modules, and compact embedded products. The combination of analog measurement, PWM, three serial interfaces, and flexible I/O reduces the need for external peripheral devices in designs requiring a single-chip controller.
PCB planning should preserve the pin-compatible footprint and route decoupling capacitors close to the supply pins. Confirm oscillator, reset, programming, and interface assignments against the manufacturer pin-description table before layout release. Firmware should also account for the ADC conversion time, peripheral interrupt behavior, and the operating limits associated with the extended-grade ordering code.
This page organizes the principal electrical, memory, interface, environmental, and package characteristics for design review. It also identifies pin-compatible Microchip alternatives, application guidance, selection trade-offs, and engineering notes intended to shorten MCU qualification and PCB bring-up work.
Drop-in alternatifler için PIC16F737-E/SO — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller PIC16F737-E/SO (aynı form faktörü ve ayağa oturma) — farklı olan Package, I/O Pins, ADC, ADC Resolution, Capture/Compare/PWM.
PIC16F737-I/SO
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F737T-I/SO
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F767-I/SO
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F767-E/SO
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F767T-I/SO
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F737-E/SO Maksimum Değerlendirmeler & Elektriksel Özellikler
| Microcontroller Type | 8-bit PIC16 RISC microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Program Memory | 7 KB Flash (4K x 14 bits) |
| Data Memory | 368 bytes RAM |
| ADC Channels | 11 channels |
| ADC Resolution | 10 bits |
| Timer Count | 3 timers |
| Capture/Compare/PWM Count | 3 modules |
| Digital I/O | 25 I/O pins |
| Synchronous Serial Interface | 3-wire SPI or 2-wire I2C |
| Asynchronous Serial Interface | USART |
| Paket | 28-pin SOIC |
| Package Width | 7.50 mm |
| Package Length | 0.295 inch |
| Terminal Count | 28 terminals |
| Temperature Grade | Automotive extended grade |
| Besleme Gerilimi | 5 V |
PIC16F737-E/SO 0.295 inch Pin Yapısı Kılavuzu
PIC16F737-E/SO (0.295 inch paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: PIC16F737-E/SO.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
PIC16F737-E/SO için uygundur 6 uygulamas: Industrial Sensor Controller, Motor and PWM Control, Automotive Control Module, Serial Protocol Bridge, Test and Measurement Instrument, LED and Lighting Controller.
Industrial Sensor Controller
The PIC16F737-E/SO fits compact sensor controllers because its 11-channel 10-bit ADC can acquire analog measurements while 25 I/O pins support discrete inputs, alarm outputs, and actuator status. The 20 MHz core provides capacity for calibration, filtering, thresholds, diagnostics, and control logic. Its three timers support periodic sampling and timeouts, while SPI, I2C, or USART can connect to remote sensors or an industrial host. The 28-pin SOIC package also simplifies assembly on cost-sensitive control boards.
Önerilen
Motor and PWM Control
The PIC16F737-E/SO is suitable for low- to moderate-power motor and actuator control because three Capture/Compare/PWM modules can generate timed outputs while three timers coordinate commutation, dead time, and periodic tasks. The 11-channel 10-bit ADC can monitor position, current, or temperature feedback, and the 25 I/O pins provide digital interface signals. External power transistors and protection are still required because the MCU controls rather than directly carries motor current.
Önerilen
Automotive Control Module
The PIC16F737-E/SO's automotive temperature grade and integrated analog and timing resources support compact vehicle control modules. The 20 MHz PIC16 core can combine sensor conditioning, diagnostic logic, actuator commands, and communication protocols, while the 11-channel 10-bit ADC handles multiple analog inputs. SPI, I2C, and USART provide interfaces to sensors, displays, or vehicle networks. Production designs must still satisfy applicable vehicle qualification, EMC, and functional-safety requirements.
Önerilen
Serial Protocol Bridge
The PIC16F737-E/SO can bridge legacy and modern serial interfaces because its synchronous port supports both 3-wire SPI and 2-wire I2C, while the USART handles asynchronous links. A 20 MHz core is suitable for framing, buffering, address decoding, and protocol translation, and the 368-byte RAM supports local data handling. The 25 I/O pins expose status indicators and configuration inputs without requiring a separate interface IC.
Önerilen
Test and Measurement Instrument
The PIC16F737-E/SO supports compact measurement instruments that combine analog inputs, digital control, and communications. Its 11-channel 10-bit ADC can acquire sensor or calibration signals, while three timers and three PWM modules organize acquisition timing and stimulus generation. The USART and configurable SPI or I2C ports allow a host computer or service interface to configure the instrument and retrieve results. Its 28-pin SOIC footprint supports panel-board layouts with moderate external I/O density.
Önerilen
LED and Lighting Controller
The PIC16F737-E/SO can coordinate multi-channel LED or general lighting control using its three Capture/Compare/PWM modules to generate accurate dimming and timing waveforms. Three timers support scheduling, debouncing, and independent timing tasks, while the ADC can monitor current, temperature, or a light sensor for feedback control. The configurable SPI or I2C port can drive display or driver devices, and the USART provides a commissioning and diagnostics path.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PIC16F737-E/SO — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PIC16F737-I/SO | PIC16F737T-I/SO | PIC16F767-I/SO | PIC16F767-E/SO | PIC16F767T-I/SO |
|---|---|---|---|---|---|---|
| Package | SOIC-28 | SOIC-28 | SOIC-28 | SOIC-28 | SOIC-28 | SOIC-28 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
Ana Farklılayıcılar
- Extended automotive ordering grade (karşılaştırma:PIC16F737-I/SO)
- Single-chip analog, timing, and communications integration (karşılaştırma:PIC16F767-E/SO)
- Twenty-five available digital I/O pins (karşılaştırma:PIC16F767T-I/SO)
Tasarım Notları
Use the manufacturer SOIC-28 land pattern and pin-description table when creating the PCB footprint. Place the decoupling network at the MCU supply pins, keep the exposed route between components short, and separate analog inputs from switching or high-current traces. Confirm oscillator and programming pins in the exact device documentation before releasing Gerber files.
Do not treat a 28-pin package as proof of functional interchangeability. Even when the footprint matches, verify ADC channels, timer resources, peripheral mappings, interrupt vectors, configuration bits, and temperature grade. PIC16F767-family substitutions require a firmware and peripheral-level review in addition to the mechanical check.
Apply the manufacturer-specified operating voltage range, decoupling values, and oscillator configuration directly to the design. Place each required bypass capacitor close to its associated supply pin and provide clean return paths for digital and analog currents. Validate brownout behavior, startup current, and peripheral loading before extending the board beyond prototype conditions.
For SPI, I2C, or USART links, calculate rise and fall times from the actual bus capacitance, driver strength, pull-up arrangement, and trace length. Avoid routing high-current or switching-node signals alongside oscillator, programming, or analog inputs. Keep clock and data timing within the electrical characteristics of the selected peripheral and connected device.
Uyumluluk Bilgisi
The automotive temperature-grade designation does not by itself establish AEC-Q100 qualification. Compliance status requires confirmation from the manufacturer product documentation or declaration.