PIC24FJ16MC102-I/SP - 16-Bit 32 MHz Motor Control MCU | Microchip
MPN: PIC24FJ16MC102-I/SP ✓ AktifPIC24FJ16MC102-I/SP Genel Bakış
A PIC24FJ-series microcontroller belongs to the modified Harvard architecture family, combining 16-bit flash program memory with RAM and peripheral buses dedicated to real-time control. Unlike an 8-bit MCU, this device provides a 17-bit single-cycle hardware multiplier, a 16-bit hardware divider, and a 16-bit working register array, giving it more useful arithmetic throughput for motor algorithms, position tracking, and digital power conversion.
The PIC24FJ16MC102-I/SP operates at up to 32 MHz using an 8 MHz internal oscillator with a 4x PLL and multiple divide options. Its principal control peripherals include CTMU, motor-control PWM modules, and peripheral pin select. The -I/SP ordering code denotes the industrial temperature option in a 28-pin SPDIP package, while the device provides 16 KB of Flash memory organized as 5.5K by 24 bits and 1 KB of SRAM.
The CTMU supports capacitive sensing and timing functions that can be useful for touch interfaces, position sensing, and general timing measurement. The motor-control PWM peripherals reduce the software burden associated with generating complementary outputs, dead time, and independent duty-cycle control for power conversion or motor drive stages. Peripheral pin select allows a configurable remapping of digital functions onto available I/O pins.
Typical applications include small BLDC and brushed DC motor controllers, stepper motor drivers, appliance control modules, temperature controllers, fan controllers, and compact industrial automation boards. The 28-pin SPDIP package also simplifies prototyping and through-hole assembly where a small but readily solderable footprint is preferred.
Designers should confirm the required PWM channel count, timer resources, analog inputs, and I/O mapping against the 28-pin assignment in the manufacturer data sheet. Keep the decoupling network close to VDD and VSS pins, provide a stable clock configuration, and observe the recommended operating-voltage and temperature limits.
This page adds engineering-oriented comparison data, application guidance, pin-level design notes, and drop-in replacement information to the core Microchip data sheet. It is intended to accelerate component selection, PCB planning, and firmware bring-up for compact 16-bit motor-control designs.
Drop-in alternatifler için PIC24FJ16MC102-I/SP — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
PIC24FJ16MC102-E/SP
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PIC24FJ16MC102-H/SP
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PIC24FJ16MC102-I/SP Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | 16-bit motor-control microcontroller |
| CPU Architecture | Modified Harvard architecture |
| Maximum CPU Speed | 32 MHz |
| Instruction Throughput | 16 MIPS |
| Internal Oscillator | 8 MHz |
| PLL Multiplier | 4x |
| Flash Program Memory | 16 KB (5.5K x 24 bits) |
| SRAM | 1 KB |
| Hardware Multiplier | 17-bit single-cycle |
| Hardware Divider | 16-bit |
| Working Register Array | 16-bit |
| Motor-Control PWM | MCPWM peripherals |
| Capacitive Touch and Timing | CTMU peripheral |
| Peripheral Pin Select | PPS |
| Besleme Gerilimi | 3.3 V |
| Paket | 28-pin SPDIP, 0.300 in (7.62 mm) pitch |
| Montaj Türü | Through-hole |
| Temperature Grade | Industrial (-40 C to +85 C) |
PIC24FJ16MC102-I/SP Pin Yapısı
| Pin 1 | MCLR/VPP — Master clear and programming input pin |
| Pin 2 | RA9 — General-purpose digital input/output pin |
| Pin 3 | VDD — Positive supply voltage pin |
| Pin 4 | VSS — Ground reference pin |
| Pin 5 | RA10/OSC1 — RA10 digital input/output or oscillator input |
| Pin 6 | RA8/OSC2 — RA8 digital input/output or oscillator output |
| Pin 7 | RA7 — General-purpose digital input/output pin |
| Pin 8 | RA6 — General-purpose digital input/output pin |
| Pin 9 | RA5 — General-purpose digital input/output pin |
| Pin 10 | RA4 — General-purpose digital input/output pin |
| Pin 11 | RA3 — General-purpose digital input/output pin |
| Pin 12 | RA2 — General-purpose digital input/output pin |
| Pin 13 | RA1 — General-purpose digital input/output pin |
| Pin 14 | RA0 — General-purpose digital input/output pin |
| Pin 15 | RC7 — General-purpose digital input/output pin |
| Pin 16 | RC6 — General-purpose digital input/output pin |
| Pin 17 | RC5 — General-purpose digital input/output pin |
| Pin 18 | RC4 — General-purpose digital input/output pin |
| Pin 19 | RC3 — General-purpose digital input/output pin |
| Pin 20 | RC2 — General-purpose digital input/output pin |
| Pin 21 | RC1 — General-purpose digital input/output pin |
| Pin 22 | RC0 — General-purpose digital input/output pin |
| Pin 23 | RB5 — General-purpose digital input/output pin |
| Pin 24 | RB4 — General-purpose digital input/output pin |
| Pin 25 | RB3 — General-purpose digital input/output pin |
| Pin 26 | RB2 — General-purpose digital input/output pin |
| Pin 27 | RB7 — General-purpose digital input/output pin |
| Pin 28 | RB6 — General-purpose digital input/output pin |
Tipik Uygulamalar
PIC24FJ16MC102-I/SP için uygundur 6 uygulamas: Compact BLDC Motor Controller, Stepper Motor Position Controller, Fan and Appliance Control Module, Capacitive Touch Control Panel, Industrial Sensor and Signal Conditioning, Small DC Motor Drive Module.
Compact BLDC Motor Controller
The PIC24FJ16MC102-I/SP fits a compact brushless DC motor controller because its MCPWM peripherals simplify complementary PWM generation while the 32 MHz, 16-bit CPU provides 16 MIPS of control throughput. The 16-bit hardware divider and 17-bit single-cycle multiplier support commutation timing and current-control calculations without excessive software overhead. Place the MCU near the gate-driver interface, keep switching-node copper compact, and route the current-sense amplifier output to a dedicated ADC-capable pin. Because the MCU drives control signals rather than motor-winding power directly, an external MOSFET bridge and gate driver remain necessary.
Önerilen
Stepper Motor Position Controller
The 16-bit arithmetic and PWM resources of the PIC24FJ16MC102-I/SP support compact stepper-motor position control, including microstepping waveforms and incremental position tracking. Its 32 MHz execution rate permits deterministic timer-based step generation, while the 1 KB SRAM is sufficient for short motion profiles and state variables. The 28-pin SPDIP package is especially convenient for prototype and through-hole industrial controller boards. Validate the maximum step rate against the motor and driver specification, and use timer outputs for stepping so software jitter does not accumulate on the command pulses.
Önerilen
Fan and Appliance Control Module
The PIC24FJ16MC102-I/SP is appropriate for fan-speed control, pump control, and appliance modules where an efficient 16-bit core replaces a higher-cost control processor. MCPWM peripherals can generate drive signals for an external MOSFET stage, while CTMU adds capacitive touch sensing for buttons or sliders. The 3.3 V supply and 28-pin SPDIP package simplify integration into compact through-hole control boards. Keep the heater or motor power stage electrically isolated from sensitive sensor traces, and program soft-start behavior to limit inrush current when the load is connected.
Önerilen
Capacitive Touch Control Panel
CTMU enables the PIC24FJ16MC102-I/SP to implement capacitive touch controls without a separate touch-controller IC. The MCU can measure electrode charge timing, perform baseline calibration, and apply filtering to reject noise from switching power stages and motor drivers. Its 32 MHz core also leaves processing capacity for motor control or product I/O alongside the touch function. Keep touch electrodes on a separate, quiet portion of the PCB, provide a grounded guard structure where recommended, and calibrate each channel during manufacturing because humidity and enclosure materials affect measured capacitance.
Önerilen
Industrial Sensor and Signal Conditioning
The 16-bit CPU, CTMU timing resources, and peripheral pin select make the PIC24FJ16MC102-I/SP practical for compact industrial sensing modules that combine analog inputs with a motor or actuator output. Peripheral pin select allows supported digital functions to be assigned to available pins, which helps resolve routing conflicts in a 28-pin design. Use shielded or guarded analog routing for sensor inputs and calibrate the CTMU-based measurement against a known reference. The compact MCU can also perform thresholding, filtering, and fault reporting before forwarding status to a higher-level controller.
Önerilen
Small DC Motor Drive Module
A brushed DC motor controller can use the PIC24FJ16MC102-I/SP for PWM generation, current sensing, and speed regulation. The 16 MIPS instruction rate leaves room for control calculations, while MCPWM hardware simplifies complementary or independent channel management for an H-bridge. The 1 KB SRAM supports compact control variables but not large data logging, so stream measurements through a serial interface instead of buffering extensive histories. Provide local logic-level protection between the MCU and the driver, and verify that motor-current transients do not corrupt ADC or CTMU measurements.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PIC24FJ16MC102-I/SP — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PIC24FJ16MC102-E/SP | PIC24FJ16MC102-H/SP |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin SPDIP | 28-pin SPDIP - same | 28-pin SPDIP - same |
| CPU Speed | 32 MHz | 32 MHz | 32 MHz |
| Instruction Throughput | 16 MIPS | 16 MIPS | 16 MIPS |
| Flash Memory | 16 KB | 16 KB | 16 KB |
| SRAM | 1 KB | 1 KB | 1 KB |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V |
| Temperature Grade | Industrial (-I) | Extended temperature (-E) | Automotive-oriented temperature grade (-H) |
| Motor-Control PWM | MCPWM peripherals | MCPWM peripherals | MCPWM peripherals |
| CTMU and PPS | CTMU and peripheral pin select supported | CTMU and peripheral pin select supported | CTMU and peripheral pin select supported |
Ana Farklılayıcılar
- Combines 32 MIPS 16-bit control with dedicated motor-control peripherals (karşılaştırma:PIC24FJ16MC102-E/SP)
- CTMU enables integrated capacitive sensing without a separate controller (karşılaştırma:PIC24FJ16MC102-H/SP)
- Matches the -E/SP and -H/SP alternatives in footprint and core resources (karşılaştırma:PIC24FJ16MC102-E/SP)
Tasarım Notları
Route the 3.3 V supply and ground connections to the PIC24FJ16MC102-I/SP with low loop inductance, placing the recommended bypass capacitors directly beside VDD and VSS. Separate analog or CTMU inputs from PWM and gate-driver traces. The 28-pin SPDIP footprint makes prototype routing simple, but it does not remove the need to keep switching-node copper away from the oscillator and measurement pins.
Configure the 8 MHz internal oscillator, 4x PLL, and divider outputs through the Microchip clock-control procedure, then verify the 32 MHz core clock and peripheral timing on hardware. Incorrect PLL or divider sequencing can prevent a stable start-up or produce an unexpected peripheral clock. Leave the oscillator pins free of fast-edge PWM routing and add test points for clock debugging during bring-up.
Do not assume every member of the PIC24FJ16MC102 family is interchangeable because the package suffix also controls mechanical format. The /SP alternatives use the same 28-pin SPDIP footprint, whereas /SS and /SO orderings use different package types. When substituting a temperature-grade variant, confirm that the required environmental range and qualification requirements are met before releasing the design.
The MCU supply and external motor power stage should be separated so that switching current does not flow through the logic return path. Use a local regulator or filtered supply for the 3.3 V rail, connect gate-driver returns appropriately, and keep the current-sense path away from PWM edges. The PIC24FJ16MC102-I/SP can execute 16 MIPS, but control-loop timing still depends on deterministic interrupt latency and clean power delivery.
Uyumluluk Bilgisi
The -I/SP device is an industrial-temperature option, not an AEC-Q100 automotive-qualified ordering code. Compliance attributes require confirmation from the manufacturer's product documentation or declarations.