TLE6285GDUMA1 LIN Transceiver with 5V LDO | Infineon
MPN: TLE6285GDUMA1 ✓ AktifTLE6285GDUMA1 Genel Bakış
A LIN transceiver is a physical-layer interface IC for the Local Interconnect Network, a low-cost, single-wire communication standard commonly used between automotive sensors, actuators, body-control modules, and electronic control units. The TLE6285GDUMA1 combines that bus interface with a linear voltage regulator, allowing one device to support LIN communication and provide a regulated 5 V rail to nearby circuitry. Its integrated 5 V output is specified as ±2%, and the regulator has a low-dropout architecture.
Key features include a maximum LIN transmission rate of 20 kBaud, compatibility with LIN 1.3 and LIN 2.0, low current consumption in sleep mode, and a LIN-bus output that is short-circuit proof to ground and battery. The integrated regulator can deliver up to 150 mA, reducing the number of discrete components needed in LIN nodes that require a local 5 V supply.
Technically, the TLE6285GDUMA1 combines the bus-level transmitter and receiver with supervisory functions for sleep behavior and an adjustable reset. These functions support robust communication in distributed vehicle electrical systems, where wiring simplicity and low standby consumption are important. The LIN bus uses one bidirectional signal conductor, while the device requires an external connection to the vehicle supply and ground.
Typical applications include automotive body-control modules, LIN-controlled seat and door modules, climate-control systems, ambient lighting controllers, sensor interfaces, and compact LIN gateways. The same general architecture can also support industrial or embedded single-wire networks when the system follows the applicable LIN physical-layer requirements.
The principal design consideration is power distribution. Although the integrated regulator can supply 150 mA, its thermal and transient behavior must be evaluated against the load current and local supply impedance. Decoupling, ground return, bus termination, and protection layout should follow the manufacturer’s recommended application circuit rather than relying solely on general LIN bus guidance.
This page consolidates the verified manufacturer and distributor information for the TLE6285GDUMA1, distinguishes documented functions from unspecified parameters, and provides application and engineering guidance beyond a basic catalog listing.
Drop-in alternatifler için TLE6285GDUMA1 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinTLE6285GDUMA1 Özellikler
| Product Type | LIN bus transceiver with integrated voltage regulator |
| LIN Transmission Rate | Up to 20 kBaud |
| LIN Specification Compatibility | LIN 1.3 and LIN 2.0 |
| ISO Compatibility | Compatible with ISO 9141 functions |
| Integrated Regulator Output | 5 V ±2% |
| Regulator Output Current Capability | 150 mA |
| Regulator Topology | Low-drop voltage regulator |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| Driver and Receiver Configuration | 1/1 |
| Sleep-Mode Current | Low current consumption; exact value not stated in supplied data |
| LIN Output Protection | Short-circuit proof to ground and battery |
| Reset Control | Adjustable reset |
| Paket | PG-DSO-11, 16 terminals, surface mount |
| Montaj Türü | Surface mount |
TLE6285GDUMA1 pg-dso-11, 16 terminals, surface mount Pin Yapısı Kılavuzu
TLE6285GDUMA1 (pg-dso-11, 16 terminals, surface mount paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: TLE6285GDUMA1.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
TLE6285GDUMA1 için uygundur 6 uygulamas: Automotive Body-Control Modules, LIN-Controlled Sensor Interfaces, Door and Window Control Modules, Climate-Control and HMI Modules, Automotive Lighting Control Nodes, Industrial Single-Wire Network Gateways.
Automotive Body-Control Modules
The TLE6285GDUMA1 fits automotive body-control modules that use a LIN subnet for switches, locks, seat functions, or other distributed loads. Its single-wire LIN interface supports rates up to 20 kBaud and is compatible with LIN 1.3 and LIN 2.0, while the integrated 5 V ±2% regulator can supply up to 150 mA to nearby interface logic. Combining the transceiver and regulator reduces the number of components required at a LIN node. Before finalizing the design, verify the device’s exact supply range, temperature rating, reset timing, and automotive qualification in the manufacturer datasheet.
Önerilen
LIN-Controlled Sensor Interfaces
The TLE6285GDUMA1 is appropriate for a LIN-connected sensor interface where a compact peripheral needs both bus communication and a local regulated supply. The integrated regulator provides 5 V ±2% with a 150 mA capability, while the 20 kBaud LIN channel connects the sensor node to a vehicle master. The bus output is short-circuit proof to ground and battery, adding useful robustness for distributed wiring environments. The designer should still confirm the allowed load current, local decoupling, LIN termination arrangement, wake-up behavior, and automotive qualification before production release.
Önerilen
Door and Window Control Modules
A door or window control module can use the TLE6285GDUMA1 as its LIN physical-layer interface when the architecture connects switches, motors, or sensors over a single-wire network. The device provides one transmitter and one receiver at up to 20 kBaud, matching conventional LIN 1.3 and LIN 2.0 communication rates. Its integrated 5 V regulator simplifies the module by supplying up to 150 mA to associated logic. Layout and protection must be reviewed for the connected motor and relay loads, and the verified operating-temperature and automotive-grade limits must be checked before qualification.
Önerilen
Climate-Control and HMI Modules
The TLE6285GDUMA1 can serve the LIN node in a climate-control or human-machine-interface module that exchanges commands and sensor data over a low-cost automotive bus. Its 20 kBaud maximum rate and compatibility with LIN 1.3 and LIN 2.0 are appropriate for control data rather than high-bandwidth multimedia traffic. The integrated 5 V, 150 mA regulator can support nearby low-power interface circuitry, although it may not cover displays, heaters, or motor drivers directly. Use the manufacturer application circuit to validate startup, grounding, and supply-noise behavior.
Önerilen
Automotive Lighting Control Nodes
The TLE6285GDUMA1 is suitable for a LIN-controlled automotive lighting node where a master ECU sends commands to a remote lamp or switch module. The 20 kBaud single-wire interface supports standard LIN 1.3 and 2.0 systems, while the integrated regulator provides a 5 V ±2% rail with up to 150 mA of capacity for control logic. The regulator should not be assumed to power high-current LEDs or lamp drivers; those loads generally require separate switching circuitry. Confirm input-voltage tolerance, transient requirements, sleep current, and protection details before using the device in an automotive lighting design.
Önerilen
Industrial Single-Wire Network Gateways
The TLE6285GDUMA1 can be considered for a compact gateway bridging a LIN-compatible single-wire network to another controller or serial interface. Its 20 kBaud limit, one transmitter, one receiver, sleep support, and adjustable reset provide the basic physical-layer functions required by a LIN node. The integrated 5 V regulator may power local interface electronics up to 150 mA, reducing supply-component count. However, industrial use requires confirmation of the exact operating-voltage and temperature limits, EMC behavior, grounding strategy, and whether the device’s automotive qualification satisfies the target system’s requirements.
Önerilen
Mühendislik referans verileri: TLE6285GDUMA1 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Brand | Infineon Technologies |
| Package | PG-DSO-11, 16 terminals |
| Product Type | LIN transceiver with integrated voltage regulator |
| LIN Transmission Rate | Up to 20 kBaud |
| LIN Specification Compatibility | LIN 1.3 and LIN 2.0 |
| ISO Compatibility | Compatible with ISO 9141 functions |
| Integrated Regulator Output | 5 V ±2% |
| Regulator Output Current | 150 mA |
| Driver and Receiver Configuration | 1/1 |
| Special Protection | LIN output short-circuit proof to ground and battery |
Ana Farklılayıcılar
- Combines LIN communication and a local regulated supply (karşılaştırma:Standalone LIN transceivers)
- Supports established automotive LIN standards (karşılaştırma:ISO 9141-only interface implementations)
- Designed for distributed wiring protection (karşılaştırma:Unprotected generic single-wire interfaces)
Tasarım Notları
The integrated regulator is rated to deliver 150 mA at 5 V ±2%. Treat that value as a maximum capability rather than an unconditional design target: account for startup current, load transients, wiring losses, and thermal dissipation. Confirm the minimum input voltage, dropout behavior, output capacitor requirements, and maximum regulator input in the complete manufacturer datasheet before assigning other circuit loads to the 5 V output.
Place the LIN transceiver and regulator support components close to their associated pins, with a short and direct ground return. Follow the manufacturer’s recommended application circuit for input and output capacitance, LIN-bus connection, and any protection components. Avoid placing sensitive analog or high-speed digital return currents beneath the LIN transceiver area, and preserve the specified pin and copper geometry of the 16-terminal PG-DSO-11 footprint.
Do not assume that the TLE6236G is a drop-in replacement merely because a comparison page lists it beside the TLE6285GDUMA1. Verify package dimensions, pin names and numbers, LIN timing, supply limits, regulator output current, reset configuration, and protection behavior against both manufacturer datasheets. Also verify whether the 5 V regulator load is external or dedicated to the transceiver when checking the complete application circuit.
The supplied verified data does not publish the full operating-voltage range, temperature range, dropout voltage, exact sleep current, or reset timing. Do not substitute typical values from other LIN transceivers or infer these limits from the 5 V ±2% output. Use the complete TLE6285 manufacturer document to validate cold-start behavior, standby loading, reset sequencing, and production limits across the intended vehicle or industrial environment.
Uyumluluk Bilgisi
The supplied verified search results do not explicitly extract RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields remain unknown rather than assuming compliance from the automotive application.
