TLS810D1EJV50XUMA1 - 5V 100mA LDO | Infineon | OPTIREG
MPN: TLS810D1EJV50XUMA1 ✓ AktifTLS810D1EJV50XUMA1 Genel Bakış
An LDO (Low-Dropout) linear regulator is a class of voltage regulator that maintains a stable output voltage even when the input voltage approaches the output voltage. LDO regulators sit inside the broader hierarchy of linear regulators -> voltage regulators -> power management ICs -> semiconductor devices. Unlike switching converters, an LDO dissipates the difference between input and output as heat, so it adds no switching noise and provides exceptionally clean power rails ideal for noise-sensitive analog and RF stages.
Key features of the TLS810D1EJV50XUMA1 include a wide 2.75 V to 42 V input operating range that tolerates automotive load-dump transients, ultra-low 9 µA quiescent current that preserves battery life in always-on subsystems, integrated output current limitation, overtemperature shutdown, and reverse-polarity protection on the input. The PG-DSO-8 exposed-pad package reduces thermal resistance and supports sustained 100 mA output without external heatsinking at moderate input voltages.
The regulator uses a PNP pass-transistor architecture with an internal precision bandgap reference and trimmed feedback network, achieving 2% output accuracy across line, load, and temperature. The wide input range also allows direct connection to 12 V and 24 V automotive rails without pre-regulation, simplifying BOM and PCB area.
Typical applications include automotive body and chassis ECUs, sensor supplies (pressure, position, temperature), CAN/LIN transceiver rails, infotainment standby rails, industrial 24 V bus sensor nodes, and battery-powered IoT edge devices requiring always-on standby regulation. The 5 V fixed output is the most common MCU and sensor rail in automotive designs.
Design consideration: power dissipation equals (VIN - VOUT) × IOUT. At VIN = 12 V, VOUT = 5 V, and 100 mA load, the device dissipates roughly 0.7 W. Ensure the PCB copper area tied to the exposed pad provides adequate heat spreading to keep the junction below the 150 °C thermal shutdown threshold.
This page synthesizes distributor pricing, drop-in alternatives in the same PG-DSO-8 footprint, and practical design notes not found in the manufacturer datasheet, providing engineers an information-gain reference for component selection and second-source decisions.
Drop-in alternatifler için TLS810D1EJV50XUMA1 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller TLS810D1EJV50XUMA1 (aynı form faktörü ve ayağa oturma) — farklı olan Output Voltage, Package, Dropout Voltage, Operating Temperature Range, Protection Features.
TLS810B1LDV50XUMA1
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TLS810A1LDV50XUMA1
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLE42642GHXUMA2
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
R5112S051B-E2-AE
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLS810D1EJV50XUMA1 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Manufacturer | Infineon Technologies |
| Product Family | OPTIREG LINEAR |
| Regulator Type | LDO (Low-Dropout) Linear Regulator - Fixed Output |
| Çıkış Türü | Fixed 5.0 V |
| Çıkış Gerilimi | 5.0 V (±2%) |
| Maksimum Çıkış Akımı | 100 mA |
| Giriş电压范围 | 2.75 V to 42 V |
| Quiescent Current (typ) | 9 µA |
| İşletim Sıcaklığı Aralığı | -40 °C to +150 °C (junction) |
| Paket | PG-DSO-8 (SO-8 with exposed pad) |
| Montaj Türü | Surface Mount |
| Output Current Limit | Yes (internal) |
| Overtemperature Shutdown | Yes (internal) |
| Reverse Polarity Protection | Yes (input) |
| Automotive Grade | Yes (OPTIREG LINEAR, AEC-Q100 qualified) |
| RoHS Durumu | Compliant |
| MSL Seviyesi | 1 |
TLS810D1EJV50XUMA1 Pin Yapısı
| Pin 1 | IN — Input voltage supply (2.75 V to 42 V) |
| Pin 2 | NC — Not connected (per datasheet) |
| Pin 3 | GND — Ground reference |
| Pin 4 | NC — Not connected (per datasheet) |
| Pin 5 | OUT — Regulated 5.0 V output |
| Pin 6 | NC — Not connected (per datasheet) |
| Pin 7 | NC — Not connected (per datasheet) |
| Pin 8 | NC — Not connected (per datasheet) |
| Pin PAD | EP — Exposed pad - thermal and electrical ground (must be soldered to PCB) |
Tipik Uygulamalar
TLS810D1EJV50XUMA1 için uygundur 6 uygulamas: Automotive Body and Chassis ECU, CAN/LIN Transceiver Power Rail, Automotive Sensor Supply (5 V), Industrial 24V Sensor Node, Battery-Powered IoT Edge Device, Infotainment Standby Rail.
Automotive Body and Chassis ECU
The TLS810D1EJV50XUMA1 is ideal for body and chassis electronic control units requiring a clean 5 V supply on a noisy 12 V/24 V vehicle bus. Its 42 V maximum input voltage and integrated reverse-polarity protection absorb load-dump and jump-start transients per ISO 7637 without external TVS clamps. The 9 µA quiescent current keeps standby drain below the typical 100 µA budget for always-on body controllers, keyless entry, and lighting ECUs. Exposed-pad PG-DSO-8 packaging reduces θJA so the LDO sustains 100 mA output across the -40 °C to +125 °C automotive underhood temperature range.
Önerilen
CAN/LIN Transceiver Power Rail
CAN and LIN transceivers require a quiet 5 V rail to maintain signal integrity on the bus. The TLS810D1EJV50XUMA1's LDO topology adds zero switching ripple, eliminating the EMI risk that buck regulators introduce near sensitive high-speed CAN-FD lines. Its 100 mA continuous output comfortably powers a transceiver plus local MCU, while the 2.75 V minimum input supports cold-crank conditions down to 6 V nominal battery (with TVS clamp). Automotive AEC-Q100 qualification makes it directly drop-in to existing 12 V CAN node designs.
Önerilen
Automotive Sensor Supply (5 V)
The TLS810D1EJV50XUMA1 powers 5 V automotive sensors including pressure, position, and temperature sensors that sit on the 12 V bus. With 2% output accuracy and ultra-low noise, it preserves sensor measurement precision and signal-to-noise ratio over the full operating temperature range. The exposed-pad SO-8 footprint supports reflow-compatible PCB assembly at high-volume automotive contract manufacturers. Reverse-polarity input protection prevents field failures from reversed battery connections during service.
Önerilen
Industrial 24V Sensor Node
Industrial 24 V bus sensor nodes benefit from the TLS810D1EJV50XUMA1's 42 V input tolerance, which provides headroom against 24 V industrial transients (IEC 61000-4-2/4-4/4-5). The 9 µA Iq preserves battery life in remote wireless sensor installations where sleep current dominates the energy budget. The 5 V fixed output directly drives microcontrollers and 4-20 mA loop interfaces in factory automation and process control. AEC-Q100 robustness translates to long-term reliability in harsh industrial environments with elevated ambient temperatures.
Önerilen
Battery-Powered IoT Edge Device
Battery-powered IoT edge devices, including smart locks, asset trackers, and remote monitoring nodes, demand multi-year battery life on a coin cell or 2xAA supply. The TLS810D1EJV50XUMA1's 9 µA quiescent current is well below the typical sleep current of an MCU with radio enabled, ensuring it does not become the bottleneck in standby power budgets. The wide 2.75 V to 42 V input range also allows direct USB or solar-panel powering in energy-harvesting designs without a pre-regulator.
Önerilen
Infotainment Standby Rail
Automotive infotainment head units require a 5 V standby rail to maintain system memory, clock, and wake-up logic when the ignition is off. The TLS810D1EJV50XUMA1 delivers this standby rail directly from the 12 V battery with only 9 µA Iq, preserving the vehicle's quiescent drain budget. Its small exposed-pad SO-8 package fits beneath the infotainment main board without forced-air cooling, and AEC-Q100 qualification supports OEM requirements for in-cabin electronics.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: TLS810D1EJV50XUMA1 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLS810B1LDV50XUMA1 | TLS810A1LDV50XUMA1 | TLE42642GHXUMA2 | R5112S051B-E2-AE |
|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Ricoh |
| Package | PG-DSO-8 (SO-8 with exposed pad) | PG-DSO-8 - same | PG-DSO-8 / TSON-10 option | PG-DSO-8 - same | PG-DSO-8 - same |
| Output Voltage | 5.0 V fixed | 5.0 V fixed | 5.0 V fixed | 5.0 V fixed | 5.0 V fixed |
| Input Voltage Range | 2.75 V to 42 V | 2.75 V to 42 V (typical) | 2.75 V to 42 V (typical) | 5.5 V to 45 V | up to ~6 V (low-Vin part) |
| Reverse-Polarity Input Protection | Yes | Yes | Yes | Yes | No (external required) |
Ana Farklılayıcılar
- 42 V maximum input voltage with reverse-polarity protection (karşılaştırma:R5112S051B-E2-AE (Ricoh))
- Ultra-low 9 µA quiescent current (karşılaştırma:TLE42642GHXUMA2)
- OPTIREG LINEAR family with full AEC-Q100 qualification (karşılaştırma:Generic cross-brand LDOs)
- Exposed-pad SO-8 footprint reduces thermal resistance (karşılaştırma:Standard SO-8 LDOs)
Tasarım Notları
Estimated: at VIN = 12 V, VOUT = 5 V, IOUT = 100 mA, power dissipation is (12 - 5) × 0.1 = 0.7 W. With θJA around 50 °C/W (typical for PG-DSO-8 with minimum pad), junction rises approximately 35 °C above ambient, well within the 150 °C thermal shutdown limit. At VIN = 24 V, dissipation rises to ~1.9 W and the exposed pad must be soldered to at least 1 cm² of copper pour for thermal headroom.
Place a 1 µF to 10 µF low-ESR ceramic input capacitor as close as possible to the IN pin to suppress input transients and provide stability. Place a 1 µF to 22 µF low-ESR ceramic output capacitor at the OUT pin (minimum ESR < 200 mΩ). The exposed pad must be soldered to the PCB thermal copper - this provides both the primary heat path and the ground reference. Keep input/output traces short and wide to minimize parasitic voltage drops.
Do not exceed the absolute maximum input voltage of 42 V; add a transient voltage suppressor (TVS) or external clamp if the input bus can see >42 V spikes. Verify input and output capacitor ESR is within the datasheet stability range - high-ESR tantalum capacitors without a parallel ceramic can cause oscillation. Ensure the input voltage does not fall below VOUT + dropout at full load, or the regulator will drop out of regulation.
Route high-current output traces separately from sensitive analog signal paths to avoid ground bounce. Connect the exposed pad to a dedicated ground copper pour that is stitched to the main ground plane with multiple vias. Keep the output capacitor ground return path short and direct to minimize ground-loop-induced noise. For automotive EMI compliance (CISPR 25), place input filter components within 5 mm of the IN pin.
Uyumluluk Bilgisi
OPTIREG LINEAR family, AEC-Q100 automotive-qualified per Infineon product page. RoHS and REACH compliant per distributor listings. Halogen-free status not explicitly stated in verified web data.
