مائیکرو کنٹرولرز

مصنوعات (20,000+)

PIC18F26K80-E/SP - 8-bit MCU, 64KB Flash, ECAN, 28-SPDIP | Microchip
PIC18F26K80-E/SP

PIC18F26K80-E/SP - 8-bit MCU, 64KB Flash, ECAN, 28-SPDIP | Microchip

The Microchip Technology PIC18F26K80-E/SP is a high-performance 8-bit PIC18 microcontroller with integrated ECAN (CAN 2.0B) and nanoWatt XLP eXtreme Low Power technology, housed in a 28-pin SPDIP package. The device operates up to 64 MHz delivering 16 MIPS, integrates 64 KB of Flash program memory, 3.6 KB of RAM and 1 KB of EEPROM, and provides 24 digital I/O pins. What is a PIC18F microcontroller? The PIC18F family is Microchip's 8-bit RISC architecture line designed for embedded control, bridging the gap between the legacy PIC16 family and the more powerful PIC24/dsPIC families. It belongs to the wider microcontroller category (MCU -> 8-bit MCU -> PIC18F -> K80 sub-family) and serves applications requiring deterministic real-time control, peripheral integration, and low-power sleep behaviour. Key features of the PIC18F26K80-E/SP include a 12-bit ADC with up to 11 channels, a CTMU (Charge Time Measurement Unit) for capacitive touch and precise time measurement, an enhanced CAN module supporting CAN 2.0B active and passive, three analogue comparators, two ECCP/SCCP modules and multiple timer peripherals. The 'K80 family is notable for its 1.8V to 5.5V operating range and very low sleep current, enabling battery-backed applications. AEC-Q100 Grade 1 qualification makes the part suitable for under-hood and cabin automotive designs. The PIC18F26K80-E/SP uses a 16-bit modified Harvard architecture with pipelined instruction fetch and a 31-level hardware stack. The internal oscillator is selectable from 32 kHz to 16 MHz, with PLL support to 64 MHz. nanoWatt XLP technology provides deep sleep modes down to a few hundred nanoamps, RTCC from a separate timer, and multiple idle modes. Typical applications include CAN node ECUs, automotive body and climate control, elevator control, industrial sensor hubs, building automation, USB-to-CAN bridges, and low-power metering. The -E temperature grade supports -40C to +125C. When designing with this MCU, observe the decoupling guideline of 0.1 uF plus bulk capacitance near VDD/AVDD pins, route the ECAN TX/RX as a differential pair with 120 ohm termination, and configure the WDT and BOR in MPLAB X projects for fail-safe bring-up. This page synthesizes distributor pricing, drop-in PIC18F alternatives, AEC-Q100 compliance notes, and practical design notes not collected on any single manufacturer page.

RFQ رابطہ
PIC18F26K80-H/MM - 64KB Flash 8-bit MCU with ECAN, 28-QFN | Microchip
PIC18F26K80-H/MM

PIC18F26K80-H/MM - 64KB Flash 8-bit MCU with ECAN, 28-QFN | Microchip

The Microchip Technology PIC18F26K80-H/MM is an 8-bit PIC18 microcontroller featuring 64KB (32K x 16) of Flash program memory, 3.6KB of RAM, and integrated ECAN (CAN 2.0B) controller, housed in a 28-pin QFN-S (6x6 mm) package with exposed thermal pad. Operating from 1.8V to 5.5V and reaching 64MHz (16 MIPS) from an internal oscillator, it is qualified to the AEC-Q100 automotive grade thanks to the -H temperature suffix (extended -40C to +150C operating range). An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash/ROM), data memory (RAM), and programmable peripherals in one package. The PIC18F family sits within Microchip's 8-bit XLP (eXtreme Low Power) portfolio, itself a branch of the broader microcontroller taxonomy (MCU -> microcontroller -> embedded controller -> semiconductor). PIC18F devices target automotive, industrial, and consumer applications that need deterministic interrupt latency, CAN connectivity, and low sleep current below 100 nA in some modes. Key features of the PIC18F26K80-H/MM include the integrated ECAN module supporting CAN 2.0B active/passive, an on-chip 12-bit ADC with up to 11 channels and CTMU support, multiple PWM and capture/compare modules, an internal 16MHz oscillator with PLL to 64MHz, and nanoWatt XLP technology for sleep currents under 100 nA. A 64-pin variant extends I/O count, but this 28-QFN-S version retains 24 I/O pins - sufficient for most sensor and actuator nodes. Architecturally the device uses an enhanced Harvard bus with separate program Flash (64KB) and data EEPROM (1KB), a hardware multiplier, and a 32-level stack. The ECAN peripheral implements the full CAN 2.0B specification including bus diagnostic features, making the chip suitable for in-vehicle networks such as body controllers, lighting modules, and HVAC systems. Typical applications include automotive ECAN body control, CAN node endpoints in industrial sensor networks, building automation (HVAC, lighting control), 12-bit data acquisition with USB/CAN bridging, and low-power remote sensor nodes. The wide 1.8V to 5.5V supply range lets a single part run from a 3.3V regulated rail or directly from a 5V automotive bus. When designing, place decoupling capacitors (100nF + 10uF) within 5mm of each VDD pin, tie MCLR through a 10k pull-up, and ensure the exposed pad is soldered to a continuous ground plane for thermal dissipation. Use Microchip's MPLAB X IDE with the XC8 compiler and the PIC18F-K80 device pack for firmware development. This page synthesizes Microchip datasheet specifications, real-time distributor pricing, and same-family alternatives - information not consolidated on any single manufacturer or distributor page.

RFQ رابطہ
PIC18F26K80-H/SS - 8-bit MCU, 64MHz, 64KB Flash, ECAN, 28-SSOP
PIC18F26K80-H/SS

PIC18F26K80-H/SS - 8-bit MCU, 64MHz, 64KB Flash, ECAN, 28-SSOP

The Microchip Technology PIC18F26K80-H/SS is a high-performance 8-bit PIC microcontroller built on the enhanced PIC18 architecture with integrated ECAN (Controller Area Network) and nanoWatt XLP extreme low-power technology. It operates from a 1.8V to 5.5V supply, executes instructions at up to 64MHz (16 MIPS), integrates 64KB of Flash program memory (organized as 32K x 16), 3.6KB of SRAM and 1KB of EEPROM, and exposes up to 24 I/O pins in a 28-pin SSOP package. The '-H' suffix denotes the high-temperature grade suitable for AEC-Q100-style automotive deployments, and '/SS' specifies the 28-SSOP (5.30 mm body width) surface-mount option. What is an 8-bit microcontroller with integrated CAN? It is a single-chip processor that combines a CPU, memory, peripherals, and a CAN bus interface in one package, sitting in the embedded hierarchy between a bare microprocessor and a complete system-on-module. The ECAN peripheral (enhanced CAN) implements the ISO 11898 CAN 2.0B protocol with hardware acceptance filters, allowing a microcontroller class device to communicate reliably on automotive and industrial CAN buses without an external controller chip. Adding nanoWatt XLP technology to this mix places the device in the low-power MCU category. Key features include a 12-bit ADC with up to 11 channels, a CTMU (Charge Time Measurement Unit) for capacitive touch and time-of-flight sensing, multiple timers, an enhanced addressable USART, SPI and I2C peripherals, and the nanoWatt XLP idle/sleep current well below typical microamps. The 28-SSOP package keeps the footprint compact for dense PCB designs while exposing the full peripheral set of the larger 40/44/64-pin family members. The device is built around a modified Harvard architecture with separate program and data buses, giving deterministic single-cycle execution for most instructions. Typical applications include automotive body and chassis ECAN nodes, industrial building-automation controllers, elevator control panels, capacitive-touch user interfaces, sensor hubs, and battery-powered remote nodes. The wide 1.8V-5.5V supply range allows direct operation from a single Li-ion cell or a regulated 3.3V/5V rail, simplifying power-tree design. AEC-Q100-grade thermal performance and ECAN make it a strong candidate for in-vehicle networking such as door modules, lighting controllers and HVAC nodes. When designing with this MCU, allocate an unused pair of I/O lines to the ECAN TX/RX pins and provide a CAN transceiver (such as MCP2551 or MCP2562) between the MCU and the bus; do not connect the MCU directly to a CAN bus without galvanic isolation considerations.

RFQ رابطہ
PIC18F26K80-I/MM - 64KB Flash 8-bit MCU w/ ECAN | Microchip
PIC18F26K80-I/MM

PIC18F26K80-I/MM - 64KB Flash 8-bit MCU w/ ECAN | Microchip

The Microchip PIC18F26K80-I/MM is a high-performance 8-bit PIC microcontroller with integrated ECAN, 64KB Flash, and 3.6KB RAM, packaged in a 28-pin QFN-S (6x6mm) with exposed pad for enhanced thermal dissipation. It operates up to 64MHz, supports 1.8V to 5.5V supply, and integrates nanoWatt XLP extreme low-power technology. The device features 24 I/O lines, a 12-bit ADC with up to 11 channels, two ECCP modules, and the ECAN controller for automotive and industrial networking. A PIC (Peripheral Interface Controller) is a family of 8-bit microcontrollers built on Harvard architecture, with separate program and data buses. The PIC18F family is the high-performance tier, offering C-friendly instruction set, hardware multiplier, and linear addressing up to 2MB. The PIC18F26K80 specifically adds integrated CAN (Controller Area Network) hardware, eliminating the need for an external CAN controller and making it well suited for in-vehicle networks and industrial automation backbones. Key differentiating features of this part include its nanoWatt XLP sleep current that extends battery life in always-on applications, hardware ECAN with DMA, and an integrated 12-bit ADC with acquisition timer. It also includes multiple serial interfaces (SPI, I2C, USART with LIN), two analog comparators, and a charge time measurement unit (CTMU) for capacitive touch or precise timing measurements. The architecture uses a modified Harvard core with a 16-bit instruction word and 8-bit data path, a hardware 8x8 multiplier, and prioritized interrupt handling. The flash program memory supports self-programming in-circuit, allowing field firmware updates without chip removal. ECAN hardware conforms to CAN 2.0B active specification with masking and filtering. Typical applications include automotive body and chassis ECAN nodes, building automation and HVAC control, industrial sensor networks, low-power remote battery-powered telemetry, and CAN-based lighting control. Its wide voltage range and ECAN make it especially compelling for 12V automotive and 24V industrial environments where a single IC handles both compute and bus termination. When designing with this MCU, ensure the exposed pad is soldered to a sufficient copper pour to meet thermal and electrical ground requirements. For ECAN nodes, use a CAN transceiver such as the MCP2561/MCP2562 and verify bus termination per ISO 11898. Programming is supported via MPLAB X IDE and ICD3/PICKit 4 debuggers. This page synthesizes distributor pricing, same-package drop-in alternatives, and design notes not typically assembled in the manufacturer datasheet, helping engineers select and source the PIC18F26K80-I/MM with confidence.

RFQ رابطہ
PIC18F26K80-I/SO - 64KB Flash 8-bit MCU w/ ECAN | Microchip
PIC18F26K80-I/SO

PIC18F26K80-I/SO - 64KB Flash 8-bit MCU w/ ECAN | Microchip

The Microchip Technology PIC18F26K80-I/SO is a high-performance 8-bit flash microcontroller with integrated ECAN (CAN 2.0B active) and nanoWatt XLP (eXtreme Low Power) technology, housed in a 28-pin SOIC wide-body package. It delivers 64 MHz (16 MIPS) performance with 64 KB of flash program memory, 3.6 KB of RAM, and 1 KB of EEPROM. The device operates from 1.8 V to 5.5 V, features a 12-bit ADC with up to 11 channels, and supports automotive temperature grades of -40°C to +85°C in the -I variant. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit CPU core - in this case Microchip's PIC18 RISC architecture - that integrates program memory (flash), data memory (SRAM), non-volatile EEPROM, and peripherals onto one die. The PIC18F26K80 sits in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. It is part of Microchip's PIC18 K-series, distinguished by integrated ECAN, XLP sleep modes, and a wide operating voltage range that supports both 3.3 V and 5 V designs. Key features include 64 KB flash (32K x 16 words), 3.6 KB RAM, 1 KB EEPROM, integrated ECAN module, a 12-bit A/D converter with up to 11 input channels, 4 hardware timers, two MSSP (SPI/I2C), two enhanced USART modules, and nanoWatt XLP sleep currents as low as 100 nA. The 12-bit ADC delivers conversion rates up to 100 ksps and supports an internal bandgap reference for ratiometric measurements. The PIC18F26K80 uses Microchip's enhanced PIC18 Harvard architecture with a 16-bit instruction word and 8-bit data path, allowing single-cycle hardware multiply and 200 ns instruction execution at 64 MHz. The ECAN module supports CAN 2.0B active with acceptance filters and masks, and the integrated CTMU (Charge Time Measurement Unit) enables touch sensing and precise time-of-flight measurements. Typical applications include industrial CAN-bus node controllers, automotive body and chassis modules, elevator control panels, building automation, sensor interfaces with analog front-ends, and low-power battery-operated sensor nodes where ECAN connectivity and nanoWatt XLP combine to enable wire-replacement topologies with extended battery life. When designing with this part, verify the SOIC-28 footprint and pinout against your PCB land pattern. For new designs, Microchip recommends the newer PIC18F26K42 family with Core Independent Peripherals unless specific ECAN migration paths are required - the K42 family uses a different oscillator and interrupt architecture and is NOT a drop-in replacement.

RFQ رابطہ
PIC18F26K80-I/SP - 64KB Flash, ECAN, 8-bit MCU | Microchip
PIC18F26K80-I/SP

PIC18F26K80-I/SP - 64KB Flash, ECAN, 8-bit MCU | Microchip

The Microchip PIC18F26K80-I/SP is a high-performance 8-bit CMOS flash microcontroller built on the PIC18 RISC architecture, featuring integrated ECAN, 64 KB of program Flash, 3648 bytes of RAM, and a 12-bit ADC with CTMU, packaged in a 28-pin SPDIP (SP) through-hole form factor. It executes instructions in 200 ns (16 MIPS at 64 MHz) and operates over a 1.8 V to 5.5 V wide supply range with nanoWatt XLP extreme low-power sleep modes for energy-constrained designs. An 8-bit microcontroller (MCU) is a programmable single-chip processor that integrates CPU, non-volatile program memory, volatile data memory, and peripherals on one die; it sits in the hierarchy: microcontroller -> embedded processor -> semiconductor device. The PIC18 family extends this with enhanced 16-bit instruction width, hardware multiply, and C-optimized architecture, while the K80 sub-family adds an on-board ECAN 2.0B controller, making the part suited to distributed industrial networks where automotive-grade robustness matters. Key features include 24 I/O pins, an internal oscillator selectable up to 64 MHz, three 16-bit timers, two CCP/ECCP modules, an enhanced USART, two SPI and two I2C peripherals, a 12-channel 12-bit ADC, and CTMU (Charge Time Measurement Unit) for capacitive touch and precise time-based measurements. The ECAN module is CAN 2.0B active with hardware filtering, and the nanoWatt XLP technology delivers sleep currents down to the nanoampere range, enabling battery-backed designs that wake on interrupt. Typical applications include automotive body and comfort modules (CAN nodes for window lifters, seat controllers), elevator control boards, industrial building automation (HVAC, lighting controllers), CAN-based sensor networks, and low-power metering with touch-button front panels. The wide 1.8 V-5.5 V range also lets the same firmware run directly from a single Li-ion cell or a regulated 5 V rail without a level shifter. When designing with this part, budget decoupling capacitance at each VDD/VSS pair (100 nF plus 1-10 µF bulk), and assign the ECAN TX/RX pins to PWM-capable ports only if pin remapping is not used, since CAN bus timing is sensitive to jitter. For new product designs, evaluate the newer PIC18F26K42 family first - it is pin-compatible but adds CIP (Core Independent Peripherals) and improved ADC. This page synthesizes distributor pricing for PIC18F26K80-I/SP, SPDIP-28 drop-in and package-compatible alternatives within the PIC18FxxK80 family, and practical design notes that extend the information found in the Microchip datasheet.

RFQ رابطہ
PIC18F26K80T-E/SO - 8-bit 64MHz 64KB Flash MCU w/ ECAN | Microchip
PIC18F26K80T-E/SO

PIC18F26K80T-E/SO - 8-bit 64MHz 64KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18F26K80T-E/SO is a high-performance 8-bit PIC18 microcontroller featuring integrated ECAN, 64KB of Flash program memory, and nanoWatt XLP (eXtreme Low Power) technology, all housed in a 28-pin SOIC package. The device operates up to 64MHz delivering 16 MIPS of computational throughput, with a wide 1.8V to 5.5V supply voltage range suited to automotive, building control, elevator control, and industrial segments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals (ADC, timers, communication interfaces) onto one silicon die. Within the broader taxonomy, the PIC18F26K80 sits in the 8-bit MCU class, under the PIC18 family of Microchip's PIC microcontrollers, which itself falls under the embedded microcontroller branch of microcontrollers and finally under the integrated-circuit and semiconductor hierarchies. XLP nanoWatt technology adds a deep-sleep idle current figure that enables battery-powered nodes to live for years on a single cell. Key features include 64KB (32K x 16) of self-programmable Flash, 3.6KB of SRAM, 1KB of EEPROM, a 12-bit A/D converter with up to 11 channels, and an on-chip CTMU (Charge Time Measurement Unit) for capacitive touch or precise time measurement. The integrated ECAN module (CAN 2.0B active) plus two EUSART, I2C, and SPI ports provide multi-protocol connectivity, making this device a true system-on-chip for networked embedded designs. The PIC18F26K80 architecture employs an enhanced Harvard bus with separate instruction and data paths, an 8-bit ALU widened by hardware multiply, and a vectored interrupt controller. The CTMU and 12-bit ADC together enable cost-effective touch sensing and precision analog measurement without external components. The "-E" suffix denotes the Extended temperature grade (-40C to +125C) and the "T" suffix indicates Tape & Reel packaging for high-volume assembly. Typical applications include automotive body and comfort networks (CAN nodes), industrial control and sensor hubs, building automation controllers, HVAC fan/blower drives, elevator control panels, and battery-powered IoT edge nodes where XLP sleep currents extend service life. The combination of ECAN and dual EUSART also makes it attractive for protocol bridges converting CAN to RS-485/232. Designers should consider the 28-pin SOIC footprint when migrating between PIC18F25K80, PIC18F26K80, and PIC18F46K80 family members, as pin assignments are largely consistent across the 28/40/44/64-pin options. Sufficient decoupling (100nF plus 10uF bulk) at VDD is critical at 64MHz operation; for ECAN applications the bus termination (120 ohm) and common-mode choke selection strongly influence EMC compliance. This page consolidates distributor pricing, pin-compatible alternatives, parametric comparisons, and application notes not aggregated in the manufacturer datasheet, giving procurement and engineering teams a single decision-ready reference.

RFQ رابطہ
PIC18F26K80T-I/MM - 8-Bit 64MHz 64KB Flash MCU w/ ECAN | Microchip
PIC18F26K80T-I/MM

PIC18F26K80T-I/MM - 8-Bit 64MHz 64KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18F26K80T-I/MM is an 8-bit PIC18 RISC microcontroller from the nanoWatt XLP family, integrating 64KB of Flash program memory, 3.6KB of RAM, and 1KB of EEPROM, all housed in a 28-pin QFN-S exposed-pad (6x6 mm) package rated for the industrial -40C to +85C temperature range. The device runs at up to 64MHz (16 MIPS) and combines on-chip ECAN, a 12-bit ADC with up to 11 channels, CTMU, and nanoWatt XLP sleep modes, with AEC-Q100 automotive qualification cited in distributor parametric data. What is an 8-bit microcontroller with integrated CAN? An MCU (microcontroller) is a single-chip computer containing a CPU core, memory, and programmable peripherals. ECAN (Enhanced Controller Area Network) is Microchip's hardware implementation of the Bosch CAN 2.0B protocol used for robust in-vehicle and industrial networking. The PIC18F26K80 family sits in the hierarchy: PIC microcontroller -> 8-bit PIC18 core -> nanoWatt XLP low-power subfamily -> K80 series with ECAN. AEC-Q100 qualification means the part has completed automotive stress-test certification. Key features include 64KB Flash organized as 32K x 16 words, 24 digital I/O lines, hardware ECAN supporting CAN 2.0B active/passive/Listen modes, a 12-bit ADC with up to 11 input channels, four 16-bit timers, two comparators, a charge-time measurement unit (CTMU), and nanoWatt XLP technology that drops typical sleep current into the nanoampere range. The internal oscillator is selectable from 31kHz to 16MHz, reducing external component count. The PIC18F26K80T-I/MM uses an enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, hardware multiplier, and a 31-deep stack. ECAN handles bit rates up to 1Mbps with filtering and acceptance masks, eliminating firmware bit-banging for automotive buses. The 12-bit ADC achieves up to 100 ksps with acquisition control, and the CTMU enables capacitive touch and time-of-flight measurement when paired with on-chip comparators. Typical applications include automotive body and chassis ECAN nodes, building climate and access control panels, industrial sensor interface boards with CAN backbone connectivity, and low-power remote sensor platforms. The wide 1.8V to 5.5V supply range supports battery-powered and 5V industrial buses directly. When designing with this MCU, reserve the exposed pad (EP) for thermal dissipation and a low-impedance ground bond; an ungrounded EP degrades ADC accuracy and ESD robustness. Use the ICSP programming interface even in production layouts to allow late-stage firmware updates, and budget for the ECAN transceiver (e.g. MCP2551 or MCP2562) as a required companion. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ رابطہ
PIC18F26K80T-I/SS - 64KB Flash 8-bit MCU w/ ECAN & XLP | Microchip
PIC18F26K80T-I/SS

PIC18F26K80T-I/SS - 64KB Flash 8-bit MCU w/ ECAN & XLP | Microchip

The Microchip Technology PIC18F26K80T-I/SS is a high-performance 8-bit microcontroller IC from the PIC18 K80 family featuring integrated ECAN and nanoWatt XLP (eXtreme Low Power) technology, packaged in a 28-pin SSOP. It operates up to 64 MHz delivering 16 MIPS, integrates 64 KB (32K x 16) of Flash program memory, 3.6 KB of RAM, and a 12-bit ADC with CTMU (Charge Time Measurement Unit), all from a 1.8 V to 5.5 V supply. The -I/SS suffix denotes the industrial temperature grade (-40C to +85C) and SSOP-28 package on tape-and-reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and programmable peripherals such as ADC, timers, communication interfaces, and I/O into one device. Within the system hierarchy, the PIC18F26K80T-I/SS is an 8-bit microcontroller -> MCU -> embedded processor -> semiconductor. The "K80" sub-family is targeted at low-power, CAN-connected embedded nodes that previously required external CAN controllers. Key features include integrated ECAN (Enhanced Controller Area Network) peripheral supporting CAN 2.0B, an on-chip 12-bit A/D converter with up to 11 channels, three analog comparators, four timers, two capture/compare/PWM modules, an 8-bit parallel slave port, and nanoWatt XLP sleep currents below 100 nA typical. The CTMU enables touch sensing, capacitive proximity, and time-of-flight measurement without external analog circuitry. The 64 MHz maximum oscillator yields 16 MIPS instruction throughput, ample for typical sensor and actuator control loops. Architecturally, the PIC18F26K80T-I/SS uses an enhanced Harvard RISC core with 16-bit instructions and 8-bit data path, plus hardware multiply and a single-cycle 8x8 multiplication. ECAN is implemented as a dedicated peripheral with independent masks/filters, reducing firmware complexity for automotive/industrial CAN nodes. Typical applications include automotive body and chassis ECAN nodes, building control (HVAC, elevator controllers), industrial sensor and actuator networks, low-power remote sensor nodes, and battery-powered metering with CAN backhaul. The wide 1.8 V-5.5 V range supports direct lithium battery and 3.3 V/5 V system buses. When designing with this part, ensure the ICSP/ICD pins (PGC/PGD, MCLR) are properly accessible for in-circuit programming and debugging, and follow Microchip AN228 for ECAN bus termination and biasing. The 28-SSOP package has moderate thermal resistance and is suitable for low-power industrial nodes. This page synthesizes verified distributor pricing, cross-family drop-in alternatives from the PIC18 K80 family, and practical ECAN/Low-Power design notes not consolidated in the manufacturer datasheet.

RFQ رابطہ
PIC18F26K83-E/ML - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F26K83-E/ML

PIC18F26K83-E/ML - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26K83-E/ML is an 8-bit PIC18 RISC microcontroller with 64KB Flash, 64MHz CPU, and integrated CAN technology in a 28-pin QFN (6x6 mm) package. It belongs to the PIC18(L)F25/26K83 family that combines a 12-bit ADC with Computation (ADC2) for advanced touch sensing and a 5-bit DAC, targeting low-power functional-safety applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripheral set, and I/O into one package. The PIC18F26K83 sits inside the broader hierarchy of embedded microcontrollers -> 8-bit microcontrollers -> PIC18 family -> Microchip PIC microcontrollers. Its extended instruction set (XLP18K) and 31-level stack allow C-friendly coding while keeping the deterministic interrupt model of the PIC architecture. Key features include a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) for touch sensing, averaging, filtering, oversampling and threshold comparison. The device integrates a 5-bit DAC, multiple communication peripherals including CAN, I2C, SPI, UART/USART, and PWMs with complementary outputs. Functional-safety (FuSa) features include a CRC scanner, windowed watchdog timer, dead-man timer, and error-correcting code on Flash memory for IEC 61508 SIL-2/3 capable designs. Operating voltage spans 2.5V to 5.5V. The PIC18F26K83-E/ML uses an 8-bit PIC18 CPU with hardware multiply and a 16-bit wide instruction path, paired with 64KB self-programmable Flash and 1KB data EEPROM. The /ML package suffix indicates a QFN-28 (6x6 mm) with an exposed pad (ML = Micro Lead-frame). Industrial -E temperature grade extends from -40C to +125C, supporting automotive and harsh-environment deployment. Typical applications include automotive body and climate control, industrial sensor hubs, touch-interface HMIs, CAN nodes, and functional-safety sensor monitoring. The 12-bit ADC2 with CVD enables robust proximity and touch buttons behind glass or plastic overlays. When designing, verify regulator headroom under 64MHz MIPS throughput. Place a 0.1uF bypass capacitor adjacent to every VDD/AVDD pin and provide a solid ground plane tie to the exposed thermal pad. The CRC scanner can be enabled at boot to validate firmware integrity before releasing critical outputs. This page synthesizes distributor pricing, drop-in Microchip family alternatives, application notes, and design guidance not bundled in the manufacturer datasheet.

RFQ رابطہ
PIC18F26K83-E/SSVAO - 64KB Flash, CAN, AEC-Q100 8-bit MCU | Microchip
PIC18F26K83-E/SSVAO

PIC18F26K83-E/SSVAO - 64KB Flash, CAN, AEC-Q100 8-bit MCU | Microchip

The Microchip Technology PIC18F26K83-E/SSVAO is a 28-pin, 8-bit PIC18 microcontroller with 64 KB Flash, 4 KB RAM, and 1 KB EEPROM, integrated with CAN technology and a 12-bit ADC with Computation (ADC2). It operates up to 64 MHz, supports an extended temperature range, and is qualified to AEC-Q100 for automotive applications, all housed in an SSOP-28 package. This device belongs to the PIC18 (L)F25/26K83 family of low-power, high-performance microcontrollers. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working RAM, EEPROM, and a rich set of peripherals such as timers, ADC, communication controllers, and I/O into one package. The K83 sub-family adds CAN, ADC2 with Capacitive Voltage Divider (CVD) for touch sensing, vector interrupts, DMA, and comparators, placing it in the mid-range of Microchip's enhanced PIC18 portfolio, suitable for industrial and automotive designs requiring deterministic real-time response. Key features include 64 KB self-programmable Flash, 4 KB SRAM, 1 KB EEPROM, a 12-bit ADC2 with up to 24 channels, three op-amps configurable as comparators, multiple communication peripherals including CAN FD, SPI, I2C, UART with LIN, and DMA for offloading core data movement. The core executes most instructions in one cycle at 64 MHz, delivering up to 16 MIPS, while the integrated nanoWatt XLP power management minimizes active and sleep currents for battery-aware designs. Architecturally, the device couples a Harvard RISC core with a wide peripheral set and Direct Memory Access (DMA), allowing deterministic data flow between ADC, communication modules, and memory without CPU intervention. ADC2 adds hardware averaging, oversampling, filtering, and threshold comparisons, enabling capacitive touch and precision sensor measurements while freeing the CPU for application logic. Typical applications include automotive body and comfort modules (lighting, seat, HVAC, mirror control), industrial CAN nodes (sensor hubs, motor control companions, isolated gateways), touch-sensing user interfaces using CVD, and home appliances requiring AEC-Q100 grade reliability and a CAN bus interface. When designing with this part, ensure the SSOP-28 land pattern is used and that unused pins are tied to defined logic levels per Microchip guidance. Verify CAN bus termination (typically 120 ohm at each end of the trunk) and place decoupling capacitors close to VDD/VSS pairs to support the ADC2 and CAN transceiver cleanly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ رابطہ
PIC18F26K83-I/ML - 8-Bit 64MHz 64KB Flash MCU w/ CAN | Microchip
PIC18F26K83-I/ML

PIC18F26K83-I/ML - 8-Bit 64MHz 64KB Flash MCU w/ CAN | Microchip

The Microchip Technology PIC18F26K83-I/ML is a 64 MHz 8-bit PIC18 XLP microcontroller with 64 KB Flash, 4 KB RAM, and integrated CAN, offered in a 28-pin QFN (6x6 mm) package with an exposed thermal pad. It operates across 2.3V-5.5V with XLP (eXtreme Low Power) technology, integrates a 12-bit ADC with Computation (ADC2) supporting Capacitive Voltage Divider (CVD) touch sensing, and provides Functional Safety (FuSa) features for safety-critical designs. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM), and programmable peripherals that engineers configure to read sensors, drive actuators, and exchange data via serial busses. PIC18 MCUs use a modified Harvard architecture optimized for deterministic real-time control, and the K-series extends that line with enhanced peripherals like ADC2, DMA, and CIP (Core Independent Peripherals). Within Microchip's 8-bit portfolio, the PIC18F26K83 sits in the K83 sub-family that combines an MSSP-based CAN module, 12-bit differential ADC, and XLP battery-friendly sleep currents below 100 nA. Key features of the PIC18F26K83-I/ML include 64 KB self-programmable Flash (32K x 16 words), 4 KB SRAM, 1 KB EEPROM, four 16-bit timers, two I2C, two SPI, four UART, and a CAN 2.0B module. ADC2 automates oversampling, averaging, and threshold comparison without CPU intervention, freeing cycles for higher-level control loops. The device also includes a Peripheral Pin Select (PPS) engine that remaps most digital peripherals to any I/O pin, simplifying PCB routing on dense boards. Designed for industrial-grade reliability, the PIC18F26K83-I/ML supports -40C to +85C operation, watch timers, windowed WDT, and CRC/SCAN memory integrity checking. The 28-QFN exposed pad provides a low theta_JA footprint suitable for compact industrial modules and energy-meter PCBs that previously required larger SSOP packages. Internal DMA moves data between peripherals and RAM without CPU load, enabling efficient noise-filter pipelines and high-speed UART/CAN traffic. Typical applications include industrial CAN node controls (sensor hubs, motor pre-drivers, building automation), touch-sensing human-machine interfaces using CVD, automotive body and accessory ECUs, e-metering, and battery-powered IoT sensor nodes. Designers benefit from MPLAB X IDE, MCC pin/clock code generators, and the PIC18F26K83 Plug-In Module (MA180037) for rapid prototyping on Microchip development boards. When selecting this part, consider that the 28-QFN variant (-I/ML, industrial -40 to +85C) is drop-in compatible with the 28-SSOP (-I/SS) and 28-SOIC (-I/SO) variants, but PCB re-layout is required to migrate between QFN and leaded packages. Designers migrating from the older PIC18F25K80 gain ADC resolution (12-bit vs 10-bit), CAN-FD capability, DMA, and CIP peripherals with software-level compatibility through the XC8 toolchain. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's K80/K42 families, design notes covering ADC2 configuration and CAN bus termination, and an AEO-optimized FAQ tailored to engineers evaluating this MCU for new designs or replacement of legacy K80 silicon.

RFQ رابطہ
PIC18F26K83-I/MX - 64KB Flash 8-bit MCU with CAN, 28-UQFN | Microchip
PIC18F26K83-I/MX

PIC18F26K83-I/MX - 64KB Flash 8-bit MCU with CAN, 28-UQFN | Microchip

The Microchip PIC18F26K83-I/MX is a low-power, high-performance 8-bit PIC microcontroller running up to 64 MHz with 64 KB of Flash, 4 KB of SRAM, and integrated CAN, in a 28-pin UQFN (6x6 mm) package. It belongs to the PIC18(L)F25/26K83 family with Functional Safety (FuSa) and XLP extreme low-power technology. An 8-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, non-volatile program memory (Flash), working RAM, and a rich set of peripherals (ADC, timers, communication ports) onto a single die. MCUs are the basic building block of every embedded system - from simple sensor nodes to industrial controllers. The PIC18 family sits in Microchip's mainstream 8-bit portfolio, positioned above baseline PIC10/12/16 parts by offering higher MIPS, more memory, CIPs (Core Independent Peripherals), and richer communication peripherals. Key features of the PIC18F26K83 include a 12-bit ADC with Computation (ADC²) supporting Capacitive Voltage Divider (CVD) for advanced touch sensing, averaging, filtering, and oversampling; a 5-bit DAC; multiple Core Independent Peripherals such as CWG, CCP, PWM, and NCO; and an integrated CAN module for automotive and industrial networking. The device supports up to 64 MHz operation from a 2.3V-5.5V supply, with XLP technology providing sub-microamp sleep currents for battery-powered applications. Architecturally, the part uses an enhanced mid-range PIC18 CPU with a hardware multiplier, indexed addressing, and a 31-level stack, allowing efficient C compilation through the MPLAB XC8 toolchain. The 28-UQFN package is the smallest footprint option in this family, with a 6x6 mm body and 0.6 mm pitch, suiting space-constrained designs that still need full peripheral integration. Typical applications include automotive body and comfort modules, industrial sensor nodes with CAN bus, low-power IoT edge devices, capacitive touch human-machine interfaces, and functional-safety systems where the FuSa documentation aids certification. The CAN bus and 12-bit ADC² make it especially strong in distributed sensor networks where deterministic low-latency conversion and reliable communication matter. When designing in this part, plan your I/O assignments carefully against the 28-pin budget: many peripherals are multiplexed onto shared pins, and CAN, the ADC, and PWM share I/O. Always consult the device pinout table before locking in the PCB layout, and provide adequate decoupling on VDD/VSS pairs near each pin cluster. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone - giving procurement and embedded engineers a faster path to a working BOM.

RFQ رابطہ
PIC18F26K83-I/SP - 8-bit 64MHz 64KB Flash MCU w/ CAN | Microchip
PIC18F26K83-I/SP

PIC18F26K83-I/SP - 8-bit 64MHz 64KB Flash MCU w/ CAN | Microchip

The Microchip Technology PIC18F26K83-I/SP is a full-featured 8-bit PIC18 XLP microcontroller integrating a 64 MHz CPU core, 64 KB of Flash program memory, 4 KB of SRAM, and a hardware CAN 2.0B controller, all in a 28-pin SPDIP (SP) through-hole package. It is part of the PIC18(L)F25/26K83 family targeted at functional-safety (FuSa), industrial, and automotive applications where deterministic CAN communication and low-power XLP operation are required. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program and data memory, plus configurable peripherals on one silicon die. The PIC18F26K83 belongs to the broader taxonomy of 8-bit microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. The 'K83' silicon combines legacy PIC18 peripherals with newer-generation IP such as a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) touch sensing, averaging, filtering and oversampling, allowing advanced touch and sensor interfaces without software state machines. Key features include the 12-bit ADC2 with up to 24 channels, four 8-bit timers plus four 16-bit timers, four 10-bit PWM modules, two USART, two SPI, two I2C, and one CAN 2.0B controller. The XLP nanoWatt XLP technology provides deep-sleep currents down to the sub-microamp range, while the integrated peripheral pin-select (PPS) remaps most digital peripherals to any I/O pin, dramatically simplifying PCB routing. Hardware DMA and vectored interrupts further offload the CPU in deterministic CAN-message handling and motor-control loops. Typical applications include CAN nodes in automotive body and chassis ECUs, industrial sensor and motor-control modules, capacitive touch user interfaces, building-automation controllers, and battery-powered IoT edge devices that require functional safety. The wide 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V rails commonly found in industrial CAN networks. When designing in this part, confirm the extended (-40 C to +125 C) 'I' temperature grade matches your environment, allocate the 28-SPDIP footprint with a socket-friendly pitch for through-hole rework, and reserve the ICD3/ICD4 pins for in-circuit debugging during firmware bring-up. Always validate the CAN bus termination and dominant-bit timing using Microchip's MPLAB X IDE and the CAN peripheral library before production release. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18F K-series, and practical design notes not found in the manufacturer datasheet alone.

RFQ رابطہ
PIC18F26K83-I/SS - 8-bit 64MHz 64KB Flash MCU | Microchip | CAN+ADC2
PIC18F26K83-I/SS

PIC18F26K83-I/SS - 8-bit 64MHz 64KB Flash MCU | Microchip | CAN+ADC2

The Microchip Technology PIC18F26K83-I/SS is an 8-bit PIC18 XLP microcontroller with CAN bus and 64KB Flash, packaged in a 28-pin SSOP. It operates at up to 64MHz, integrates a 12-bit ADC with Computation (ADC2), and offers 25 I/O pins in an industrial -40C to +85C temperature range. A microcontroller (MCU) is an integrated circuit that combines a CPU core, volatile memory (RAM), non-volatile program memory (Flash/ROM), and configurable peripherals on a single die. Within the broader taxonomy, the PIC18F26K83 sits in the 8-bit PIC18 family -> PIC microcontrollers -> microcontrollers (MCU) -> microcontrollers and processors -> embedded semiconductors. Its XLP (eXtreme Low Power) pedigree targets battery-powered and always-on designs where nanoWatt sleep currents and fast wake-up times are critical. Key features include 64KB (32K x 16 words) Flash program memory, 4KB RAM, 1KB EEPROM, a 64MHz internal oscillator, and a 12-bit ADC2 with Capacitive Voltage Divider (CVD) hardware automation for advanced touch sensing, oversampling, averaging and filtering. Communication peripherals include CAN, I2C, SPI, UART/USART and LINbus, supported by DMA, vector interrupts, a 16-bit PWM module, and a windowed watchdog timer. Functional Safety (FuSa) features suit IEC 60730 class B-capable appliance designs. Architecturally the PIC18F26K83 uses Microchip's enhanced Harvard RISC core with a 16-bit instruction word and an 8-bit data path, augmented by a hardware multiplier and a 32-level stack. The ADC2 peripheral offloads sensor post-processing via dedicated hardware, reducing CPU wake events and enabling lower system power. Typical applications include CAN-connected industrial sensors, automotive body and comfort modules, capacitive touch user interfaces, appliance control boards, building automation nodes, and LIN/CAN gateways. Its combination of CAN, ADC2 and XLP makes it a strong fit for space-constrained, networked, low-power embedded systems. When designing with this device, place a 100 nF decoupling capacitor on VDD within 3 mm of the pin and a bulk 10 uF near the IC, route the 28-pin SSOP thermal pad and unused I/O per Microchip's guidelines, and reserve ICSP programming pins (PGC/PGD) with test-point access for production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ رابطہ
PIC18F26K83T-I/MX - 64KB Flash, CAN, 8-bit MCU | Microchip
PIC18F26K83T-I/MX

PIC18F26K83T-I/MX - 64KB Flash, CAN, 8-bit MCU | Microchip

The Microchip PIC18F26K83T-I/MX is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 4KB RAM, integrated CAN 2.0B, and a 12-bit ADC with Computation (ADC²) for advanced touch sensing and signal conditioning, packaged in a 28-UQFN (6x6 mm). It operates up to 64MHz across 2.3V–5.5V with eXtreme Low Power (XLP) sleep currents under 1 µA, and is part of the Functional Safety (FuSa) family. An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that combines a RISC instruction set, on-chip Flash program memory, SRAM data memory, and a rich set of peripherals (timers, ADC, PWM, communication modules) into a single die. Within the broader taxonomy, the PIC18F26K83 sits below the PIC18 family → 8-bit MCU → microcontroller → embedded controller → semiconductor, and is positioned for low-power mixed-signal applications where CAN connectivity and analog integration are required. Key differentiating features include ADC² (12-bit, with Capacitive Voltage Divider, averaging, filtering, and automatic threshold comparison), up to four dedicated PWM channels with edge-aligned and center-aligned modes, a Configurable Logic Cell (CLC), three 16-bit timers, four CCP modules, two UART, two SPI, and an I²C module. The integrated CAN 2.0B controller with filtering supports robust industrial and automotive networked nodes. The PIC18F26K83 implements a 16-bit instruction word with a modified Harvard bus, dual 16-level hardware stack, and a peripheral pin select (PPS) scheme that lets designers remap digital peripherals onto a wide range of I/O pins, simplifying PCB layout. The on-chip 32kHz oscillator and PLL enable low-jitter operation while preserving XLP sleep performance. Typical applications include industrial sensor nodes with CAN, HVAC controls, building automation, low-power IoT sensor hubs, capacitive touch user interfaces, and small motor-control stages where the integrated PWM and ADC simplify the BOM. When designing with this device, take advantage of the ADC² CVD hardware for cap-touch buttons and sliders to eliminate external touch ICs, and use the PPS system to place peripheral signals on convenient pins without board rework. This page synthesizes Microchip datasheet specifications, current distributor pricing, pin-compatible alternatives, and practical design notes that go beyond the catalog summary.

RFQ رابطہ
PIC18F26K83T-I/SO - 8-Bit 64MHz MCU, 64KB Flash, 28-SOIC | Microchip
PIC18F26K83T-I/SO

PIC18F26K83T-I/SO - 8-Bit 64MHz MCU, 64KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC18F26K83T-I/SO is an 8-bit PIC microcontroller from the PIC® XLP™ 18K family with Functional Safety (FuSa) capability, running at 64 MHz with 64 KB of Flash program memory, 4 KB of SRAM, and 1 KB of EEPROM, all housed in a 28-pin SOIC package. It integrates a 12-bit ADC with Computation (ADC²) for automated Capacitive Voltage Divider (CVD) touch sensing, a 5-bit DAC, multiple communication peripherals, and an integrated CAN module. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that processes data in 8-bit wide paths and integrates CPU core, non-volatile Flash program memory, volatile SRAM data memory, peripherals, and I/O on one die. 8-bit MCUs sit within the broader category of microcontrollers -> embedded processors -> semiconductor ICs. They remain dominant in cost-sensitive and low-power applications because of mature toolchains, predictable real-time behavior, and very low standby current draw, all of which make them the workhorse of the embedded industry. Key features of the PIC18F26K83 include XLP (eXtreme Low Power) technology for sub-µA sleep currents, a 12-bit ADC with computation engine for averaging and oversampling, hardware CAN 2.0B, four 16-bit timers, two I²C, two SPI, two UART, a 5-bit DAC, and CTMU for capacitive touch. The 28-SOIC variant (the SO package) gives 25 user I/O pins, sufficient for sensor nodes and human-interface designs. Architecturally, the part uses a modified Harvard architecture with a 16-bit instruction word and 8-bit data path, a 31-level hardware stack, and a priority-level interrupt controller. ADC² offloads averaging, oversampling, filtering, and threshold detection from the CPU, freeing MIPS for application logic and reducing firmware complexity for touch and sensor signal chains. Typical applications include automotive body and sensor nodes (via CAN), industrial control and sensor hubs, capacitive touch human interfaces, low-power IoT edge nodes, and functional-safety designs that require IEC 61508 SIL capable documentation. The wide 2.3 V to 5.5 V operating range and robust peripherals support battery-powered systems as well as 5 V industrial buses. Design tip: reserve a stable, low-impedance ground plane under the MCU and keep analog traces short when routing the 12-bit ADC inputs to preserve signal integrity. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.

RFQ رابطہ
PIC18F26Q10-E/ML - 8-Bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/ML

PIC18F26Q10-E/ML - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/ML is an 8-bit PIC18 XLP microcontroller delivering 64 MHz CPU performance with 64 KB Flash, 4 KB SRAM, and 256 B EEPROM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It operates from 2.5 V to 5.5 V with 5 V tolerance on digital I/O, integrates a 10-bit ADC with Computation (ADC2), a 5-bit DAC, four 10-bit PWM outputs, configurable logic cells (CLC), complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and scan/CRC for functional-safety applications. An 8-bit microcontroller (MCU) is a single-chip computer optimized for embedded control, executing one byte per instruction cycle while integrating CPU, non-volatile program memory, RAM, and peripherals on one die. Within the semiconductor hierarchy, the PIC18F26Q10-E/ML is a microcontroller belonging to the 8-bit MCU class, a sub-category of microcontrollers, which themselves sit under embedded processors, broader mixed-signal ICs, and finally the semiconductor taxonomy. Its 8-bit RISC core, modified Harvard architecture, and 5 V I/O tolerance make it distinct from 3.3 V ARM Cortex-M parts. Key features include Functional Safety (FuSa) support, ultra-low-power XLP sleep currents, 36 instruction set, hardware multiplier, direct and indirect addressing modes, multiple I/O ports (PORTA/PORTB/PORTC), and on-board debug via ICD/ICSP. The 64 KB Flash supports 100K endurance cycles typical, with self-programmability and code protection. The 28-QFN (6x6) package provides 23 I/O pins and a low thermal resistance path through the exposed pad for high-current GPIO drive. The PIC18-Q10 architecture pairs a deterministic 8-bit core with Core Independent Peripherals (CIPs) - CLC, CWG, HLT, and ADC2 - which offload timing-critical tasks from the CPU, improving real-time responsiveness. The 5 V operation directly interfaces to industrial sensors, motor drivers, and noisy environments without external level shifters, reducing BOM and PCB area. Typical applications include industrial sensor nodes, BLDC/PMSM motor control, LED lighting controllers, home appliances, automotive body and chassis ECUs (non-safety), IoT edge nodes with long battery life, and human-machine interfaces. The XLP nanoWatt technology enables sleep currents below 50 nA typical, suiting battery-backed designs. When designing with this device, allocate the exposed pad (EP) as the primary thermal dissipation path, place a 100 nF decoupling capacitor on each VDD pin, and reserve the ICSP/ICD pins for in-circuit programming to simplify firmware iteration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - enabling faster vendor comparison and supply-chain decisions.

RFQ رابطہ
PIC18F26Q10-E/SO - 8-Bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/SO

PIC18F26Q10-E/SO - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/SO is a 28-pin 8-bit microcontroller from the PIC18-Q10 family, operating at up to 64 MHz with 64 KB of Flash program memory in a 28-SOIC package. This XLP (eXtreme Low Power) device integrates intelligent analog peripherals, configurable logic cells (CLCs), and 5V operation for enhanced noise immunity in harsh environments. A microcontroller (MCU) is a single-chip computer that contains a CPU, RAM, non-volatile program memory, and peripherals such as ADCs, timers, and communication interfaces. MCUs form the lowest tier of embedded computing hierarchy: microcontroller -> embedded processor -> SoC -> computing platform. PIC18 MCUs use a modified Harvard architecture with separate program and data buses, enabling single-cycle instruction execution while accessing both Flash and SRAM in the same cycle. Key features of the PIC18F26Q10 include 64 KB (64K x 8) of self-programmable Flash, 4 KB of SRAM, 256 bytes of EEPROM, and a 10-bit ADC with up to 24 channels. The device also integrates a 5-bit DAC, complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and CRC/SCAN hardware for functional safety. Its extended voltage range of 1.8V to 5.5V supports both battery and 5V regulated rails, and the Functional Safety (FuSa) classification simplifies IEC 61508 SIL-aware designs. Architecturally, the PIC18F26Q10 employs Microchip's enhanced mid-range core with a 16-bit instruction word and 8-bit data path, achieving 16 MIPS at 64 MHz. Configurable Logic Cells (CLCs) allow on-chip inter-peripheral routing without external glue logic, while the Peripheral Pin Select (PPS) enables flexible signal mapping to I/O pins. This combination reduces BOM count, PCB area, and firmware complexity for sensor nodes and motor control loops. Typical applications include industrial sensor nodes, IoT edge devices, low-power remote controls, home appliances, and automotive body controllers. The 5V tolerance and integrated op amps suit analog front-end designs where signal conditioning must coexist with digital control. Designers should enable the on-chip voltage regulator for 5V operation and use the CLCs to implement simple state machines that would otherwise require a CPLD. The PIC18F26Q10-E variant carries the extended operating temperature range of -40C to +125C suitable for industrial environments. This page synthesizes XAIPART distributor pricing, pin-compatible drop-in alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.

RFQ رابطہ
PIC18F26Q10-E/SP - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/SP

PIC18F26Q10-E/SP - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/SP is an 8-bit RISC microcontroller built on the PIC18 CPU core, operating up to 64 MHz with 64 KB of Flash program memory, 3.6 KB of SRAM and 256 bytes of EEPROM, housed in a 28-pin SPDIP (SP) through-hole package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, peripherals and I/O. Within the broader semiconductor taxonomy the PIC18F26Q10 belongs to the 8-bit MCU family, the PIC® XLP™ 18Q sub-family, and Microchip's Functional Safety (FuSa) line; it sits inside the microcontroller -> embedded controller -> power management-aware signal processing node class. Its 5V-native operation increases noise immunity for industrial sensor and real-time control nodes. Key features include a 10-bit ADC with computation (ADC2), a 5-bit DAC, two comparators, a zero-cross detect (ZCD), complementary waveform generator (CWG), 10-bit PWM with CCP, windowed watchdog timer (WWDT), hardware limit timer (HLT), CRC/SCAN accelerator, peripheral pin select (PPS) and four configurable logic cells (CLC). The CIP (Core Independent Peripherals) blocks let the CPU offload deterministic tasks, improving real-time response. Architecturally, the part uses an 8-bit modified Harvard bus with a 16-bit instruction word, a hardware multiplier and 49 instructions; the 64 MHz internal oscillator drives a 16 MIPS instruction throughput. The non-volatile memory is rated for high-endurance Flash and EEPROM suitable for frequent parameter storage. Typical applications include industrial sensor nodes, motor and pump control, white goods, automotive body and lighting subsystems, IoT edge nodes and low-power battery-powered metering. The Q10 family's noise-tolerant 5V I/O and CIP mix make it a strong fit for BLDC and AC-DC power-conversion auxiliary control. When designing, prefer using the CLCs and CWG for hard-real-time signaling, leave the WWDT enabled for safety, and use ADC2 computation modes to average the analog channel in hardware before waking the CPU. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet.

RFQ رابطہ
PIC18F26Q10-E/SS - 64KB Flash 8-bit MCU, 64MHz, 28-SSOP | Microchip
PIC18F26Q10-E/SS

PIC18F26Q10-E/SS - 64KB Flash 8-bit MCU, 64MHz, 28-SSOP | Microchip

The Microchip Technology PIC18F26Q10-E/SS is an 8-bit PIC18 XLP microcontroller featuring 64KB of Flash program memory, 4KB of SRAM, and 256 bytes of EEPROM, operating at up to 64MHz in a 28-pin SSOP (5.30mm body) package with extended (-40C to +125C) temperature grade. Designed for robust real-time control and sensor node applications, the PIC18F26Q10 family integrates intelligent analog peripherals, configurable logic cells (CLCs), and 5V operation for enhanced noise immunity in industrial environments. The part's broad peripheral set includes a 10-bit ADC with computation (ADC2), a 5-bit DAC, multiple PWM channels, a complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and SCAN/CRC for functional safety applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data path. The PIC18 architecture is an enhanced 8-bit Harvard RISC core with 16-bit instructions, sitting within the broader hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor. PIC18 "XLP" parts target ultra-low-power designs, and the PIC18F26Q10 is part of Microchip's Functional Safety (FuSa) capable family with built-in CRC/SCAN for IEC 61508 SIL-aware designs. Key features include 25 general-purpose I/O pins, two 16-bit timers, configurable logic cells for custom hardware glue, zero-cross detect, and on-chip temperature indicator. The device supports 1.8V to 5.5V operation, providing flexibility across 3.3V and 5V rails common in industrial and consumer designs. The 28-SSOP package offers a compact, surface-mount form factor with a standard 0.65mm pin pitch. Typical applications include industrial control loops, IoT sensor nodes, touch-sensing front-ends, automotive body/comfort modules, and low-power battery-driven edge devices. The 5V tolerant I/O and integrated analog simplify designs that interface with legacy 5V sensors and actuators. When designing with this MCU, plan oscillator and ICSP layout to keep the ICSPDAT/ICSPCLK traces short, and verify CRC/SCAN configuration in MPLAB X Code Configurator (MCC) before code freeze for functional safety projects. The device supports in-circuit serial programming (ICSP) and debugging via Microchip's ICD tools. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the same PIC18 family, and practical design notes not always consolidated in the manufacturer datasheet.

RFQ رابطہ
PIC18F26Q10-I/ML - 8-bit MCU, 64KB Flash, 64MHz, 28-QFN | Microchip
PIC18F26Q10-I/ML

PIC18F26Q10-I/ML - 8-bit MCU, 64KB Flash, 64MHz, 28-QFN | Microchip

The Microchip Technology PIC18F26Q10-I/ML is an 8-bit PIC microcontroller from the PIC18 Q10 family, featuring 64KB of Flash program memory, 3.6KB (3600 bytes) of SRAM, and 1024 bytes of EEPROM in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It operates up to 64 MHz, supports 2.3V to 5.5V supply voltage, and integrates intelligent analog peripherals including a 10-bit ADC, a 5-bit DAC, configurable logic cells, complementary waveform generators, and a hardware scan/CRC block for functional-safety applications. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a Harvard-architecture microcontroller based on an 8-bit data path with separate program and data buses, designed for deterministic real-time control. The PIC18 Q10 family sits within Microchip's broader PIC18 (8-bit) -> PIC microcontroller -> microcontroller -> embedded processor hierarchy, offering more peripherals, memory, and CIPs (Core Independent Peripherals) than baseline PIC10/12/16 parts. The "Q10" family name is a Microchip branding convention denoting the integrated analog and CIP feature set. Key features of the PIC18F26Q10-I/ML include Core Independent Peripherals that offload timing-critical tasks from the CPU, eXtreme Low Power (XLP) technology for energy-sensitive designs, 5V operation for increased noise immunity in industrial environments, and a Functional Safety (FuSa) feature set targeting IEC 61508 / SIL-capable applications. The 28-QFN package provides a small 6x6 mm footprint suitable for space-constrained sensor nodes and motor-control boards. Typical applications include IoT sensor nodes, real-time control loops, lighting ballast controllers, white-goods motor drivers, automotive body and sensor modules, and any cost-sensitive embedded design requiring deterministic CIP-based timing. The 5V tolerant I/O makes it well suited for industrial environments with long cable runs where ground bounce and EMI are concerns. When designing with this device, ensure proper decoupling (100 nF + bulk capacitor near VDD), review the device's errata for any CIP-specific limitations, and confirm whether the I/ML (28-QFN) package matches your PCB layout - the same PIC18F26Q10 die is also offered in SOIC-28, SSOP-28, and QFN-28 variants for layout flexibility.

RFQ رابطہ
PIC18F26Q10-I/SO - 64KB Flash 8-bit MCU 64MHz SOIC-28 | Microchip
PIC18F26Q10-I/SO

PIC18F26Q10-I/SO - 64KB Flash 8-bit MCU 64MHz SOIC-28 | Microchip

The Microchip Technology PIC18F26Q10-I/SO is an 8-bit PIC® XLP™ microcontroller delivering 64 MHz CPU performance, 64 KB Flash, 4 KB SRAM and 1024 B EEPROM in a 28-pin SOIC (SO) package. It features an integrated 10-bit ADC with computation (ADC2), a 5-bit DAC, configurable PWM/CWG/HLT peripherals and a functional-safety (FuSa) capable core with WWDT and CRC/SCAN. A PIC18 microcontroller is an 8-bit Harvard-architecture RISC MCU from Microchip's PIC18 family, used widely in real-time control, sensor conditioning and low-power embedded applications. Within the broader taxonomy it sits under: 8-bit microcontroller -> microcontroller (MCU) -> embedded processor -> semiconductor. The Q10 sub-family specifically targets low-power (XLP), 5V-noise-immune designs with intelligent analog and rich configurable peripherals for sensor nodes and IoT endpoints. Key features of this part include 64 KB self-programmable Flash with program flash write/read protection, 1024 B high-endurance EEPROM rated for 100k erase/write cycles, four 16-bit timers, two USART modules, two SPI/I2C modules, 25-channel 10-bit ADC2 with hardware accumulation and threshold compare, a 5-bit DAC, two comparators and CWG (Configurable Logic Cell plus Complementary Waveform Generator). The CIP (Core Independent Peripherals) approach lets designers implement motor drive, lighting, power conversion and sensor signal chains without CPU intervention. Operating voltage spans 2.3V to 5.5V with 5V-tolerant digital I/O, allowing direct interface to noisy 5V industrial buses. Power-managed modes (Run/Idle/Doze/Sleep) plus Peripheral Module Disable (PMD) yield nanoWatt XLP sleep currents suitable for battery-powered sensor nodes. The functional-safety subsystem (Windowed WWDT, CRC, SCAN, HLT) supports IEC 60730 / Class B safety requirements in home appliances and industrial sensors. Typical applications include industrial control, robust sensor nodes, consumer electronics, automotive body and accessory modules, touch sensing, IoT edge nodes, and home appliance Class-B safety controllers. The device is particularly well-suited for designs migrating from older PIC16/PIC18F K-series parts that need modern CIP peripherals without leaving the 8-bit ecosystem. When designing with this part, ensure the 28-pin SOIC footprint matches your PCB land pattern (JEDEC MS-013) and that decoupling includes a 100 nF + bulk capacitor pair within a few millimeters of VDD/AVDD. The -I industrial temperature grade (-40C to +85C) and SOIC package suit through-hole-friendly wave soldering or hand rework on mixed-technology boards. This page synthesizes distributor pricing across DigiKey, Mouser, Win-Source and Octopart plus practical drop-in alternatives and design notes not found in the manufacturer datasheet itself.

RFQ رابطہ
PIC18F26Q10-I/SS - 64KB Flash 8-bit MCU 28-SSOP | Microchip
PIC18F26Q10-I/SS

PIC18F26Q10-I/SS - 64KB Flash 8-bit MCU 28-SSOP | Microchip

The Microchip Technology PIC18F26Q10-I/SS is an 8-bit PIC® XLP™ microcontroller with 64KB Flash, 4KB RAM, and 256B EEPROM, operating up to 64MHz core clock in a 28-pin SSOP package. The device integrates intelligent analog peripherals including a 10-bit ADC with computation (ADC2), a 5-/10-bit DAC, configurable logic cells (CLCs), Complementary Waveform Generator (CWG), and hardware limit timer (HLT), all in a 5V-capable architecture with enhanced noise immunity. An 8-bit microcontroller (MCU) is a compact single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), non-volatile EEPROM, and digital/analog peripherals onto one silicon die. Within the broader taxonomy, the PIC18F26Q10 belongs to the 8-bit MCU category, which itself sits inside microcontrollers, which fall under integrated circuits (ICs), and ultimately semiconductors. The 'F' prefix denotes Flash program memory; 'Q10' identifies the family introduced for robust real-time control and sensor-node applications. Compared with 32-bit ARM Cortex-M MCUs, 8-bit PIC18 devices typically trade raw computational throughput for deterministic latency, lower power consumption, and lower BOM cost. Key features include 64KB self-programmable Flash with high-endurance program memory, 4KB SRAM, 256 bytes EEPROM, 25 general-purpose I/O pins, and a peripheral set encompassing two USART, two SPI, two I²C, 10-bit ADC2, 5-/10-bit DAC, CLC, CWG, HLT, Windowed WWDT, and CRC/SCAN. The 'I' suffix denotes the industrial -40°C to +85°C operating range, and the 5V-tolerant I/O architecture permits direct interfacing with legacy 5V logic. The device uses a Harvard RISC architecture with a 16-bit instruction word and an 8-bit data path, executing most instructions in a single cycle for a peak throughput of 16 MIPS at 64MHz. Core Independent Peripherals (CIPs) such as CLC and CWG can implement custom combinational/sequential logic and complementary PWM without CPU intervention, offloading deterministic tasks and reducing firmware complexity. Typical applications include industrial control nodes, sensor signal conditioning, touch and proximity interfaces, automotive LIN slave nodes, IoT edge devices, and consumer appliances. Designers should leverage the 5V-tolerant I/O for robust interfaces and use ADC2 with computation for sensor averaging and oversampling in low-power sensor hubs.

RFQ رابطہ