ADM488ARZ - 250 kbps Full-Duplex RS-485/422 Transceiver | Analog Devices
MPN: ADM488ARZ ✓ فعالADM488ARZ جائزہ
An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver for balanced digital communication. The RS-485 standard is widely used for robust, multidrop buses in industrial automation, building controls, instrumentation, and communications equipment. ADM488ARZ is also compatible with RS-422 applications, allowing the same device to support point-to-point or multipoint balanced data transmission where the system architecture permits it.
The principal operating features are a 250 kbps maximum data rate, a single 5 V supply with ±10% tolerance, a −7 V to +12 V bus common-mode range, and approximately 12 kΩ input impedance. The slew rate is intentionally reduced to limit electromagnetic interference generated by the transmitter. The device also provides electrostatic-discharge protection of 2 kV EFT according to IEC1000-4-4 and high electromagnetic-immunity capability according to IEC1000-4-3, making it appropriate for electrically noisy environments.
The ADM488ARZ uses a differential driver and receiver architecture to reject common-mode noise while transmitting data over twisted-pair cabling. Its reduced slew rate helps lower radiated emissions, but the maximum supported data rate remains limited to 250 kbps. The approximate 74 µA operating supply current shown in the comparison information supports low-power system designs. In a full-duplex implementation, separate transmit and receive paths are used, requiring separate differential pairs connected to the bus system.
Typical applications include industrial measurement systems, factory automation equipment, building and HVAC controllers, telemetry links, data acquisition units, and isolated or non-isolated RS-485 communication modules. The 8-pin SOIC package supports conventional surface-mount assembly. In an RS-485 interface, the bus should include termination resistors at the physical ends, biasing to prevent an idle bus from floating, and protection appropriate to the installation environment.
When designing around ADM488ARZ, verify the transceiver enable and shutdown states, cable length, topology, grounding strategy, and the voltage limits imposed by connected equipment. The reduced slew rate can improve electromagnetic compatibility but may require attention to bus timing at the highest supported data rate. This page provides the manufacturer product overview, technical specifications, application guidance, comparison information, and practical replacement considerations for faster component selection.
کے لیے ڈراپ اِن متبادل ADM488ARZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADM488ARZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Bus Common-Mode Range, EFT Protection, Mounting Type, Package, Product Type.
ADM488ARZ-REEL7
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
SN65LBC179P
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ISL8488IPZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM488AN
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADM488ARZ تفصیلات
| Product Type | Full-duplex differential line transceiver |
| Supported Standards | EIA RS-485 and RS-422 |
| Maximum Data Rate | 250 kbps |
| سپلائی وولٹیج | 5 V ±10% |
| Bus Common-Mode Range | −7 V to +12 V |
| Input Impedance | 12 kΩ |
| Operating Supply Current | 74 µA |
| EFT Protection | 2 kV per IEC1000-4-4 |
| Electromagnetic Immunity | High immunity per IEC1000-4-3 |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| آپریٹنگ درجہ حرارت رینج | −40°C to +85°C |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Operating Mode | Full duplex |
| Slew Rate | Reduced slew rate for low electromagnetic interference |
ADM488ARZ 8-pin soic پن کنفیگریشن گائیڈ
ADM488ARZ (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ADM488ARZ.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
ADM488ARZ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Bus, Building and HVAC Control, Data Acquisition and Instrumentation, Telemetry and Remote Monitoring, Factory Motor-Control Systems, Test and Measurement Equipment.
Industrial Automation Bus
The ADM488ARZ fits 250 kbps RS-485 links between PLCs, sensors, actuators, and remote I/O modules. Its differential driver and receiver support balanced multipoint communication, while the reduced slew rate helps limit radiated emissions in cabinet environments. The single 5 V ±10% supply and approximately 74 µA operating current simplify low-power node implementations. Designers should still verify industrial EMC, grounding, surge, and isolation requirements.
تجویز کردہ
Building and HVAC Control
ADM488ARZ is well suited to balanced control-bus communications in building-management and HVAC systems, where 250 kbps is normally adequate and reduced EMI is useful near motors and switching equipment. The −7 V to +12 V bus common-mode range provides tolerance for ground-potential differences between connected controllers. Termination at the physical bus ends, fail-safe biasing, and careful separation from high-current switching paths remain essential implementation requirements.
تجویز کردہ
Data Acquisition and Instrumentation
The ADM488ARZ can connect laboratory or industrial data-acquisition equipment to remote sensors through a full-duplex RS-485 link. Differential signaling improves noise immunity, and the 250 kbps rate accommodates many multiplexed measurement channels without imposing the power and EMI cost of a much faster edge rate. The transceiver's 8-pin SOIC format supports compact interface sections, although the system must meet isolation and ground-reference requirements independently of the IC.
تجویز کردہ
Telemetry and Remote Monitoring
ADM488ARZ supports remote telemetry links where distributed equipment must exchange command and measurement data over balanced copper cabling. The reduced-slew-rate transmitter lowers EMI, while the receiver's differential structure rejects common-mode disturbances encountered between field equipment and the controller. The device is appropriate for links at or below 250 kbps; cable length, topology, isolation, surge exposure, and grounding should be evaluated as part of the complete communication link.
تجویز کردہ
Factory Motor-Control Systems
The ADM488ARZ can provide the low-speed communications path between motor controllers, condition-monitoring equipment, and factory supervisory systems. Its reduced slew rate is advantageous when the transceiver is routed near motor drive circuits and power converters, because slower edges generally reduce high-frequency emissions. Keep the bus physically separated from switching nodes and route the differential pair as a pair. The transceiver does not replace isolation, surge protection, or functional-safety measures.
تجویز کردہ
Test and Measurement Equipment
ADM488ARZ can connect bench instruments, production testers, and automated measurement systems to a remote RS-485 controller. At up to 250 kbps, it supports command traffic and periodic measurement results while limiting bus EMI. The device's low operating supply current is useful in compact multi-channel equipment, but the design must provide proper bus termination and fail-safe biasing. Verify the complete timing budget because the reduced slew rate intentionally limits transition speed.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ADM488ARZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ADM488ARZ-REEL7 | SN65LBC179P | ISL8488IPZ | ADM488AN |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Texas Instruments | Renesas Electronics | Analog Devices |
| Supported Standards | EIA RS-485 and RS-422 | EIA RS-485 and RS-422 | RS-485/RS-422 | RS-485/RS-422 | EIA RS-485 and RS-422 |
اہم امتیازی خصوصیات
- Reduced slew rate supports lower-emission bus operation (بمقابلہSN65LBC179P)
- Specified for balanced RS-485 and RS-422 communication (بمقابلہISL8488IPZ)
- Low-power 5 V operation in an 8-pin SOIC package (بمقابلہADM488AN)
ڈیزائن نوٹس
Route the differential driver and receiver traces as a tightly coupled pair over a continuous ground plane. Keep the pair length balanced, avoid stubs, and maintain clearance from switching nodes and high-current power paths. Place termination components near the physical bus endpoints rather than beside the transceiver unless the topology specifically requires local termination. A full-duplex RS-485 bus normally uses separate driver and receiver pairs, so do not combine those connections without reviewing the system architecture.
The reduced slew rate is intentional and is central to the ADM488ARZ's low-EMI behavior. Do not treat the 250 kbps specification as permission to use a faster transceiver without recalculating cable length, propagation delay, topology, and emissions. Also verify enable and shutdown states before assuming the bus is in fail-safe operation. The verified material does not reproduce the complete pin table, so assign all pins from the current Analog Devices data sheet.
Use a continuous reference plane and return each differential pair through the same physical region. Keep the transceiver away from relay contacts, motor-switching nodes, and high-di/dt power loops. The −7 V to +12 V common-mode range helps tolerate ground offsets, but it does not remove the need for a sound grounding strategy. For long or industrial cables, evaluate external surge and ESD protection and verify that it does not distort the intended receiver threshold or bus loading.
Provide a local 5 V ±10% rail with low impedance and place the required bypass capacitors close to the supply and ground pins according to the manufacturer layout guidance. Decouple shared supply sections locally so switching loads cannot pull the transceiver rail outside its operating range. The approximately 74 µA operating supply current is low, but it does not include every enabled, loaded, or fault-state condition; use the manufacturer electrical-characteristics limits for worst-case power budgeting.
تعمیل کی معلومات
The verified material identifies 2 kV EFT protection according to IEC1000-4-4 and high electromagnetic immunity according to IEC1000-4-3. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited product information.