ATSAMD10D13A-MUT - ARM Cortex-M0+ MCU, 48MHz, 8KB Flash | Microchip
MPN: ATSAMD10D13A-MUT ✓ فعالATSAMD10D13A-MUT جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and GPIO. The ATSAMD10D13A sits inside the Cortex-M0+ ecosystem, the smallest and most energy-efficient member of the ARM Cortex-M family, optimized for deterministic real-time control and low active/standby power. Within Microchip's portfolio it belongs to the broader hierarchy of 32-bit MCU -> ARM Cortex-M0+ MCU -> SAM D microcontroller -> SAM D10D sub-family -> power management and industrial control IC family.
Key features of the ATSAMD10D13A-MUT include a 32-bit Cortex-M0+ core with single-cycle I/O access, 8KB Flash with read-while-write support, 4KB SRAM, an integrated 12-bit ADC, multiple SERCOM (serial communication) interfaces configurable as UART/SPI/I2C, a 16-bit timer/counter, and a full-speed USB 2.0 device interface on selected package pins. The device operates from a 1.62V to 3.63V supply and offers multiple low-power sleep modes (IDLE, STANDBY, BACKUP) that drop current consumption to a few microamps, enabling battery-powered and energy-harvesting designs.
Technically, the ATSAMD10D13A uses Microchip's proprietary event system and Peripheral Touch Controller (PTC) supporting capacitive touch sensing via hardware-accelerated acquisition. The single-cycle I/O port provides deterministic GPIO access for time-critical control loops, while the SERCOM peripherals are highly flexible and remappable. Built-in hardware CRC, true random number generator, and secure boot features strengthen firmware integrity for connected applications.
Typical applications include home automation nodes, smart lighting, IoT sensor endpoints, consumer HMI, low-cost industrial metering, capacitive touch keypads, and USB HID peripherals. The combination of small QFN-24 footprint and 8KB Flash makes it ideal for size-constrained, low-cost 32-bit designs migrating from 8-bit PIC or AVR architectures. When designing with this device, ensure decoupling capacitors are placed within 3mm of the VDD pins, and reserve PA24/PA25 for SWD if in-circuit debugging is required.
کے لیے ڈراپ اِن متبادل ATSAMD10D13A-MUT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ATSAMD10D13A-MUT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, ADC, DAC, Program Memory (Flash), Mounting Type.
ATSAMD10D14A-MUT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATSAMD10D13A-MU
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATSAMD10D13A-SSNT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATSAMC20G15A-MUT
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAMD10D13A-MUT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Processor | ARM Cortex-M0+ |
| Core Size | 32-Bit |
| زیادہ سے زیادہ کلاک فریکوئنسی | 48 MHz |
| CoreMark/MHz | 2.46 |
| Program Memory (Flash) | 8 KB (8K x 8) |
| RAM Size | 4 KB |
| Supply Voltage (VDD) | 1.62 V to 3.63 V |
| آپریٹنگ درجہ حرارت | -40 C to +85 C |
| پیکیج | 24-QFN (4x4 mm) with exposed pad |
| پن کی تعداد | 24 |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Packaging | Tape & Reel (T/R) |
| Series | SAM D10D |
| MSL لیول | 3 (168 hours) |
| RoHS اسٹیٹس | Compliant |
ATSAMD10D13A-MUT پن کنفیگریشن
| پن 1 | PA00 — GPIO/SERCOM/I2C/ADC |
| پن 2 | PA01 — GPIO/SERCOM/I2C/ADC |
| پن 3 | PA02 — GPIO/SERCOM/ADC |
| پن 4 | PA03 — GPIO/SERCOM/ADC/REF |
| پن 5 | GND — Ground |
| پن 6 | VDD — Digital supply voltage |
| پن 7 | PA04 — GPIO/SERCOM/ADC |
| پن 8 | PA05 — GPIO/SERCOM/ADC |
| پن 9 | PA06 — GPIO/SERCOM/ADC |
| پن 10 | PA07 — GPIO/SERCOM/ADC |
| پن 11 | PA08 — GPIO/SERCOM/I2C |
| پن 12 | PA09 — GPIO/SERCOM/I2C |
| پن 13 | PA10 — GPIO/SERCOM/I2C |
| پن 14 | PA11 — GPIO/SERCOM/I2C |
| پن 15 | GND — Ground |
| پن 16 | VDD — Digital supply voltage |
| پن 17 | PA14 — GPIO/SERCOM/I2C |
| پن 18 | PA15 — GPIO/SERCOM/I2C |
| پن 19 | PA22 — GPIO/SERCOM/I2C/TC |
| پن 20 | PA23 — GPIO/SERCOM/I2C/TC |
| پن 21 | PA24 — GPIO/SERCOM/USB DP |
| پن 22 | PA25 — GPIO/SERCOM/USB DM |
| پن 23 | PA28 — RESETN |
| پن 24 | EP — Exposed pad - must be soldered to GND for thermal dissipation |
عام استعمالات
ATSAMD10D13A-MUT کے لیے موزوں ہے 6 ایپلیکیشنs: Home Automation Sensor Nodes, Smart Lighting Control, Capacitive Touch Keypads, Low-Cost Industrial Metering, USB HID Peripherals, Wearable Health Bands.
Home Automation Sensor Nodes
The ATSAMD10D13A-MUT is well-suited for home automation sensor endpoints such as door/window contact sensors, motion detectors, and wireless thermostat remotes. Its 32-bit ARM Cortex-M0+ core at 48 MHz easily handles Zigbee or BLE stack pre-processing, while the 4 KB SRAM supports modest buffering. Multiple SERCOM channels provide flexible UART/SPI/I2C connections to radios and environmental sensors, and the 1.62V-3.63V supply range lets the device run directly from a single CR2032 coin cell. The 4x4 mm 24-QFN footprint fits inside the smallest sensor puck housings, and Standby currents in the low microamp range extend battery life to multi-year levels in typical duty-cycled operation.
تجویز کردہ
Smart Lighting Control
For smart LED drivers and dimmer modules, the ATSAMD10D13A-MUT combines an integrated 12-bit ADC for current/voltage sensing with PWM outputs for smooth dimming. Its 48 MHz Cortex-M0+ core can run color-mixing algorithms (HSL to RGB) and basic DMX-512 or DALI receive parsing without external logic. The 8 KB Flash fits reference firmware for Matter-over-Thread bridges or proprietary 2.4 GHz protocols. The 4x4 mm QFN-24 footprint integrates beneath compact MR16 or downlight PCBs, and the 1.62V-3.63V range allows direct connection to constant-current LED driver stages. The Peripheral Touch Controller (PTC) supports capacitive slider/button overlays on glass-fronted fixtures.
تجویز کردہ
Capacitive Touch Keypads
The ATSAMD10D13A-MUT's hardware Peripheral Touch Controller (PTC) supports up to 12 mutual-capacitance buttons or a slider/wheel without any external touch IC. Designers can implement water-tolerant touch interfaces for appliances, consumer electronics, and industrial HMI panels. The Cortex-M0+ at 48 MHz executes Microchip's QTouch library for noise immunity and moisture rejection algorithms, while 4 KB SRAM holds recent touch states and gesture buffers. The 24-QFN (4x4 mm) package mounts on the back of a touch PCB, leaving the front side free for the sensor pattern. Low-power sleep modes keep standby current below 5 uA, satisfying battery-powered remote controls.
تجویز کردہ
Low-Cost Industrial Metering
For sub-1 kHz metering such as water flow, gas pulse counters, and small electric submetering, the ATSAMD10D13A-MUT offers precise 16-bit timer capture, an internal 12-bit ADC, and hardware CRC for tamper detection. Its Cortex-M0+ at 48 MHz runs calibrated measurement routines and Modbus RTU framing over a SERCOM-configured UART, fitting comfortably within 8 KB Flash. The 4x4 mm QFN-24 package fits behind the LCD or 7-segment display of a metering module, and the wide 1.62V-3.63V supply accommodates 3.3V regulated or two-AA battery operation. Low-power Standby modes below 5 uA enable ten-year battery life in residential metering.
تجویز کردہ
USB HID Peripherals
Although the SAM D10 lacks a built-in USB transceiver, the SERCOM plus a low-cost external USB bridge makes the ATSAMD10D13A-MUT a practical host for simple HID peripherals such as barcode scanners, custom keyboards, and HID-class game controllers. The 48 MHz core handles HID report formatting and feature reports without an external RTOS, and 4 KB SRAM holds HID ring buffers. Designers save BOM cost versus higher-end Cortex-M4 parts, and the 4x4 mm QFN-24 footprint leaves board space for cable termination and ESD protection. The 1.62V-3.63V supply works directly from USB-derived 3.3V after LDO regulation.
تجویز کردہ
Wearable Health Bands
Wearable bands for fitness and basic health monitoring benefit from the ATSAMD10D13A-MUT's combination of Cortex-M0+ 32-bit processing, low-power modes, and the 4x4 mm QFN-24 footprint. The device can interface via SERCOM I2C/SPI to optical heart-rate sensors, 6-axis IMUs, and small OLED displays, while the integrated 12-bit ADC reads battery voltage and skin-contact electrodes. Sleep currents below 5 uA allow multi-day battery life when the IMU and optical sensor are duty-cycled. Designers use the 4 KB SRAM for step-counter buffers and BLE radio command queues, and 8 KB Flash holds firmware with over-the-air update stubs for next-gen device models.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ATSAMD10D13A-MUT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ATSAMD10D14A-MUT | ATSAMD10D13A-MU | ATSAMC20G15A-MUT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-QFN (4x4 mm) | 24-QFN (4x4 mm) - same | 24-QFN (4x4 mm) - same | 48-QFN - different |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Clock Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Size | 8 KB | 16 KB (+100%) | 8 KB | 16 KB |
| SRAM Size | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Voltage | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V | 2.7V to 5.5V |
| Series | SAM D10D | SAM D10D | SAM D10D | SAM C20G |
اہم امتیازی خصوصیات
- Higher Flash density within the same SAM D10D family (بمقابلہATSAMD10D14A-MUT)
- Tray packaging option for low-volume prototypes (بمقابلہATSAMD10D13A-MU)
- Lower pin count and smaller footprint than SAM C20 series (بمقابلہATSAMC20G15A-MUT)
ڈیزائن نوٹس
The ATSAMD10D13A-MUT requires VDD (pin 6 and 16) and VDDCORE (pin 23) decoupling. Place one 100 nF X7R ceramic within 3 mm of each VDD pin and one 1 uF X7R near VDDCORE. The exposed pad (EP) must be soldered to a continuous GND plane with thermal vias for heat dissipation; without a properly soldered EP, power dissipation capability drops and latch-up risk increases.
At 48 MHz with all peripherals active, the device dissipates roughly 30-40 mW under typical load. The QFN-24 package thermal resistance theta_JA is approximately 50 C/W on a 4-layer JEDEC test board, giving a 1.5-2 C rise above ambient. For applications pushing 3.3V/48 MHz with continuous ADC sampling, the EP must be soldered to at least 100 mm^2 of GND copper. Estimated: based on standard QFN-24 thermal pad and 4-layer 1-oz copper.
Keep the SWD signals PA30 (SWCLK) and PA31 (SWDIO) trace length below 50 mm and avoid routing them adjacent to high-frequency switching signals. The RESETN pin (PA28) requires a 10 kohm pull-up to VDD and a 100 nF capacitor to GND for noise immunity. Unused GPIO pins should be configured as outputs low or inputs with internal pull-up enabled to minimize standby current.
Do not power the device above 3.63V - even brief transients from an inductive supply can exceed absolute maximum ratings. Avoid using the bootloader on first production boards unless fuse bits are cleared, as a locked device can brick the unit. Verify the GPNVM bits in NVMCTRL after programming to confirm Flash row-write protection is configured correctly for your security model.
تعمیل کی معلومات
RoHS and REACH compliance per Microchip product declaration. Not AEC-Q100 qualified; for automotive applications choose ATSAMC20E or ATSAMx51xx variants. Halogen-free matte-tin plating, MSL-3 (168 hours).
