ATSAME51N19A-AU - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
MPN: ATSAME51N19A-AU ✓ فعالATSAME51N19A-AU جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code, SRAM for data), and a rich set of peripherals (timers, ADC/DAC, communication interfaces, GPIOs). MCUs sit within the embedded computing hierarchy: MCU -> embedded processor -> semiconductor IC. The Cortex-M4F core specifically adds a single-precision Floating Point Unit and DSP extensions, making it well-suited for signal processing and motor control. The ATSAME51N19A-AU uses the ARM Cortex-M4F architecture, the industry-standard 32-bit core for high-performance embedded designs.
Key features include 120 MHz CPU clock, 512 KB Flash with ECC, 192 KB SRAM, a high-speed 16-bit ADC, USB 2.0 full-speed with on-chip transceiver, multiple CAN-FD interfaces, SERCOM serial interfaces configurable as UART/SPI/I2C, and a cryptographic accelerator for AES, SHA, and True Random Number Generator (TRNG). The device also provides up to 6 SERCOM channels, a 12-bit DAC, and a touch controller. Memory protection unit (MPU) and TrustZone-M support enable secure firmware execution.
Typical applications include industrial control systems, building automation, smart energy metering, motor control, USB peripherals, IoT edge nodes, and human-machine interface (HMI) panels. The combination of high-speed ADC, FPU-based DSP capability, and CAN-FD interfaces suits it for real-time control loops in industrial automation, where deterministic response and signal fidelity matter.
Design consideration: When migrating firmware between SAM D51 and SAM E51, verify that the E51's clock-gating and SERCOM channel count match your pin assignments. Use MPLAB X IDE with the SAME51 Device Family Pack and configure the GCLK generator carefully when sharing peripherals across SERCOM and the ADC to avoid bandwidth conflicts.
This page consolidates distributor pricing, drop-in alternative cross-references, and practical design guidance for the ATSAME51N19A-AU that go beyond the bare datasheet excerpt.
کے لیے ڈراپ اِن متبادل ATSAME51N19A-AU — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ATSAME51N19A-AU (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف ADC, SRAM, Operating Temperature, DAC, MSL Level.
ATSAME51N19A-AUT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAMD51N19A-AF
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAMD51P19A-AU
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATSAME54N20A-AU
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAME51J20A-AUT-EFP
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAMD51J19A-AFT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAME51N19A-AU زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | ARM Cortex-M4F with FPU |
| زیادہ سے زیادہ کلاک فریکوئنسی | 120 MHz |
| Program Memory (Flash) | 512 KB with ECC |
| SRAM | 192 KB |
| پیکیج | 100-pin TQFP (14x14 mm) |
| Operating Temperature Grade | -40°C to +85°C (industrial) |
| Operating Voltage Range | 1.71 V to 3.6 V |
| ADC | Up to 2x 12-bit, 1 MSPS |
| DAC | 12-bit, 1 MSPS |
| USB | USB 2.0 Full-Speed, on-chip transceiver |
| CAN | CAN-FD |
| SERCOM Channels | Up to 8 (UART/SPI/I2C configurable) |
| Cryptographic Accelerator | AES, SHA, TRNG |
| TrustZone-M | Supported |
| DMA Channels | 32 |
| RoHS اسٹیٹس | Compliant |
ATSAME51N19A-AU پن کنفیگریشن
| پن 1 | PD0 — GPIO / SERCOM3 pad 0 |
| پن 2 | PD1 — GPIO / SERCOM3 pad 1 |
| پن 3 | PD2 — GPIO / SERCOM3 pad 2 |
| پن 4 | PD3 — GPIO / SERCOM3 pad 3 |
| پن 5 | VDDIO — Digital I/O supply voltage |
| پن 6 | GND — Ground |
| پن 7 | PD4 — GPIO / SERCOM3 pad 0 alt |
| پن 8 | PD5 — GPIO / SERCOM3 pad 1 alt |
| پن 9 | PD6 — GPIO / SERCOM3 pad 2 alt |
| پن 10 | PD7 — GPIO / SERCOM3 pad 3 alt |
| پن 11 | PD8 — GPIO / SERCOM4 pad 0 |
| پن 12 | PD9 — GPIO / SERCOM4 pad 1 |
| پن 13 | PD10 — GPIO / SERCOM4 pad 2 |
| پن 14 | PD11 — GPIO / SERCOM4 pad 3 |
| پن 15 | PD12 — GPIO / SERCOM5 pad 0 |
| پن 16 | PD13 — GPIO / SERCOM5 pad 1 |
| پن 17 | PA0 — GPIO / SERCOM0 pad 0 |
| پن 18 | PA1 — GPIO / SERCOM0 pad 1 |
| پن 19 | PA2 — GPIO / SERCOM0 pad 2 |
| پن 20 | PA3 — GPIO / SERCOM0 pad 3 |
| پن 21 | PA4 — GPIO / SERCOM0 pad 0 alt |
| پن 22 | PA5 — GPIO / SERCOM0 pad 1 alt |
| پن 23 | PA6 — GPIO / SERCOM0 pad 2 alt |
| پن 24 | PA7 — GPIO / SERCOM0 pad 3 alt |
| پن 25 | PA8 — GPIO / SERCOM1 pad 0 |
| پن 26 | PA9 — GPIO / SERCOM1 pad 1 |
| پن 27 | PA10 — GPIO / SERCOM1 pad 2 |
| پن 28 | PA11 — GPIO / SERCOM1 pad 3 |
| پن 29 | PA12 — GPIO / SERCOM2 pad 0 |
| پن 30 | PA13 — GPIO / SERCOM2 pad 1 |
| پن 31 | PA14 — GPIO / SERCOM2 pad 2 |
| پن 32 | PA15 — GPIO / SERCOM2 pad 3 |
| پن 33 | PA16 — GPIO / SERCOM5 pad 0 alt |
| پن 34 | PA17 — GPIO / SERCOM5 pad 1 alt |
| پن 35 | PA18 — GPIO / SERCOM1 pad 0 alt |
| پن 36 | PA19 — GPIO / SERCOM1 pad 1 alt |
| پن 37 | PA20 — GPIO / SERCOM5 pad 2 alt |
| پن 38 | PA21 — GPIO / SERCOM5 pad 3 alt |
| پن 39 | PA22 — GPIO / SERCOM3 pad 0 alt |
| پن 40 | PA23 — GPIO / SERCOM3 pad 1 alt |
| پن 41 | PA24 — GPIO / SERCOM3 pad 2 alt |
| پن 42 | PA25 — GPIO / SERCOM3 pad 3 alt |
| پن 43 | GND — Ground |
| پن 44 | VDDIO — Digital I/O supply voltage |
| پن 45 | PB0 — GPIO / SERCOM5 pad 0 |
| پن 46 | PB1 — GPIO / SERCOM5 pad 1 |
| پن 47 | PB2 — GPIO / SERCOM5 pad 2 |
| پن 48 | PB3 — GPIO / SERCOM5 pad 3 |
| پن 49 | PB4 — GPIO / SERCOM4 pad 0 |
| پن 50 | PB5 — GPIO / SERCOM4 pad 1 |
| پن 51 | PB6 — GPIO / SERCOM4 pad 2 |
| پن 52 | PB7 — GPIO / SERCOM4 pad 3 |
| پن 53 | PB8 — GPIO / SERCOM0 pad 0 alt |
| پن 54 | PB9 — GPIO / SERCOM0 pad 1 alt |
| پن 55 | PB10 — GPIO / SERCOM0 pad 2 alt |
| پن 56 | PB11 — GPIO / SERCOM0 pad 3 alt |
| پن 57 | PB12 — GPIO / SERCOM2 pad 0 alt |
| پن 58 | PB13 — GPIO / SERCOM2 pad 1 alt |
| پن 59 | PB14 — GPIO / SERCOM2 pad 2 alt |
| پن 60 | PB15 — GPIO / SERCOM2 pad 3 alt |
| پن 61 | PB16 — GPIO / SERCOM4 pad 0 alt |
| پن 62 | PB17 — GPIO / SERCOM4 pad 1 alt |
| پن 63 | PB18 — GPIO / SERCOM4 pad 2 alt |
| پن 64 | PB19 — GPIO / SERCOM4 pad 3 alt |
| پن 65 | PB20 — GPIO / SERCOM5 pad 0 alt |
| پن 66 | PB21 — GPIO / SERCOM5 pad 1 alt |
| پن 67 | PB22 — GPIO / SERCOM1 pad 0 alt |
| پن 68 | PB23 — GPIO / SERCOM1 pad 1 alt |
| پن 69 | PB24 — GPIO / SERCOM1 pad 2 alt |
| پن 70 | PB25 — GPIO / SERCOM1 pad 3 alt |
| پن 71 | PB26 — GPIO / SERCOM2 pad 0 alt |
| پن 72 | PB27 — GPIO / SERCOM2 pad 1 alt |
| پن 73 | PB28 — GPIO / SERCOM2 pad 2 alt |
| پن 74 | PB29 — GPIO / SERCOM2 pad 3 alt |
| پن 75 | PB30 — GPIO / SERCOM5 pad 2 alt |
| پن 76 | PB31 — GPIO / SERCOM5 pad 3 alt |
| پن 77 | PC0 — GPIO / SERCOM6 pad 0 |
| پن 78 | PC1 — GPIO / SERCOM6 pad 1 |
| پن 79 | PC2 — GPIO / SERCOM6 pad 2 |
| پن 80 | PC3 — GPIO / SERCOM6 pad 3 |
| پن 81 | PC4 — GPIO / SERCOM7 pad 0 |
| پن 82 | PC5 — GPIO / SERCOM7 pad 1 |
| پن 83 | PC6 — GPIO / SERCOM7 pad 2 |
| پن 84 | PC7 — GPIO / SERCOM7 pad 3 |
| پن 85 | VDDIN — Voltage regulator input supply |
| پن 86 | GND — Ground |
| پن 87 | PC8 — GPIO / SERCOM6 pad 0 alt |
| پن 88 | PC9 — GPIO / SERCOM6 pad 1 alt |
| پن 89 | PC10 — GPIO / SERCOM6 pad 2 alt |
| پن 90 | PC11 — GPIO / SERCOM6 pad 3 alt |
| پن 91 | PC12 — GPIO / SERCOM7 pad 0 alt |
| پن 92 | PC13 — GPIO / SERCOM7 pad 1 alt |
| پن 93 | PC14 — GPIO / SERCOM7 pad 2 alt |
| پن 94 | PC15 — GPIO / SERCOM7 pad 3 alt |
| پن 95 | PC16 — GPIO / SERCOM0 pad 0 alt |
| پن 96 | PC17 — GPIO / SERCOM0 pad 1 alt |
| پن 97 | PC18 — GPIO / SERCOM0 pad 2 alt |
| پن 98 | PC19 — GPIO / SERCOM0 pad 3 alt |
| پن 99 | RESET_N — Reset input (active low) |
| پن 100 | GND — Ground |
عام استعمالات
ATSAME51N19A-AU کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Motor Control, Building Automation and HVAC Controllers, Smart Energy Metering, USB Industrial Peripherals, IoT Edge Sensor Nodes, Human-Machine Interface (HMI) Panels.
Industrial Motor Control
The ATSAME51N19A-AU's ARM Cortex-M4F core with single-precision FPU executes field-oriented control (FOC) loops in real time at 120 MHz, while its 12-bit 1 MSPS ADC samples phase currents with sufficient resolution for sinusoidal commutation. Up to 8 SERCOM channels allow simultaneous SPI encoder feedback and UART communication with a controller. Hardware floating-point multiplications and PWM-synchronized ADC triggering via the TCC timer counter-event system yield deterministic sub-1 µs control loop periods, suitable for PMSM, BLDC, and stepper drives up to several kW. The industrial temperature grade (-40°C to +85°C) and ECC Flash make the E51 deployable in factory-floor cabinets without reliability concerns.
تجویز کردہ
Building Automation and HVAC Controllers
Building automation gateways require deterministic CAN-FD bus handling for BACnet/Modbus traffic, real-time sensor scanning, and secure firmware updates. The ATSAME51N19A-AU integrates a CAN-FD controller and USB 2.0 Full-Speed with on-chip transceiver for direct host connectivity without external PHY. The TrustZone-M isolation allows secure OTA firmware validation via the AES-256/SHA-256/TRNG crypto block while keeping application logic in a non-secure memory partition. The 100-pin TQFP provides ample GPIO for relay drivers, 0-10 V analog outputs, and multiple UARTs for RS-485 sensor networks. Industrial-grade temperature operation ensures reliability in unconditioned electrical closets and rooftop HVAC enclosures.
تجویز کردہ
Smart Energy Metering
Single-phase and poly-phase energy meters demand high-accuracy ADC sampling at 4 kSPS per channel with simultaneous computation of RMS voltage, current, and active/reactive power. The ATSAME51N19A-AU's 12-bit ADC paired with the Cortex-M4F DSP extensions (single-cycle MAC, SIMD) executes per-sample power calculations inside the ADC interrupt service routine without CPU saturation. Hardware AES-128 encryption of tariff data, cryptographic signing of meter readings, and TRNG-seeded key generation protect against tampering. The 512 KB dual-panel Flash supports concurrent firmware updates mandated by smart-grid regulations, while the ECC Flash detects bit errors caused by electrical noise on the meter bus.
تجویز کردہ
USB Industrial Peripherals
USB Human Interface Devices (HID), data-acquisition interfaces, and industrial input panels benefit from the ATSAME51N19A-AU's integrated USB 2.0 Full-Speed PHY that eliminates external transceiver cost. The 120 MHz Cortex-M4F core handles HID report generation, ADC streaming at 1 MSPS, and DMA-driven bulk transfers without CPU intervention via 32 DMA channels. The 8 SERCOM interfaces allow simultaneous connections to multiple UART sensors (RS-232/RS-485), SPI displays, and I2C peripherals. The USB bootloader in ROM supports field firmware updates over the same USB port, and the TrustZone-M isolation can protect device authentication keys from firmware compromise.
تجویز کردہ
IoT Edge Sensor Nodes
Industrial IoT gateways aggregating sensor data over LoRa, sub-GHz wireless, or Wi-Fi modules require sufficient processing for edge analytics, secure key storage, and reliable connectivity stacks. The ATSAME51N19A-AU runs MQTT-SN or CoAP stacks in addition to encryption (AES) and authentication (SHA-256) in the cryptographic accelerator, freeing the CPU from crypto overhead. 192 KB SRAM accommodates TLS 1.2/1.3 handshakes for secure cloud connectivity, while the dual-panel 512 KB Flash supports A/B firmware partitions for OTA updates. The 100-pin TQFP package and 1.71-3.6 V supply voltage allow direct battery or solar-power operation in remote deployments.
تجویز کردہ
Human-Machine Interface (HMI) Panels
Industrial HMI panels integrate touch displays, RGB interfaces, and multiple serial peripherals while running real-time graphics. The ATSAME51N19A-AU's SERCOM channels connect to SPI displays, I2C touch controllers, and UART sensor ports simultaneously. The Cortex-M4F FPU accelerates JPEG decoding and graphics rendering, while the 192 KB SRAM accommodates framebuffers for small color TFTs. The 12-bit DAC drives audio alerts, and the TCC timers generate backlight PWM with phase-shifted outputs for LED matrix dimming. TrustZone-M protects the UI firmware from unauthorized modification, and the industrial temperature grade supports panel-mount deployments near heat-generating equipment.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ATSAME51N19A-AU — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ATSAME51N19A-AUT | ATSAMD51N19A-AF | ATSAMD51P19A-AU | ATSAME54N20A-AU | ATSAME51J20A-AUT-EFP |
|---|---|---|---|---|---|---|
| Package | 100-pin TQFP (14x14) | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F |
| Max Clock Speed | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash | 512 KB | 512 KB | 512 KB | 512 KB | 1 MB | 1 MB |
| SRAM | 192 KB | 192 KB | 192 KB | 192 KB | 256 KB | 256 KB |
| Cryptographic Accelerator | Yes (AES/SHA/TRNG) | Yes (AES/SHA/TRNG) | No | No | Yes (AES/SHA/TRNG) | Yes (AES/SHA/TRNG) |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Supply Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
اہم امتیازی خصوصیات
- Integrated cryptographic accelerator for industrial security (بمقابلہATSAMD51P19A-AU)
- Dual-panel Flash with ECC for live firmware updates (بمقابلہATSAMD51J19A-AFT)
- CAN-FD controller for industrial fieldbus (بمقابلہATSAME51J18A-AF)
ڈیزائن نوٹس
The ATSAME51N19A-AU requires a 1.71-3.6 V supply on VDDIN with a separate VDDIO domain for I/O. Decouple both rails with 100 nF ceramic capacitors placed within 5 mm of each supply pin, plus a 4.7 µF bulk capacitor per rail. The on-chip voltage regulator requires an external 1 µF capacitor on the VDDOUT pin for core stability. In USB applications, the VDDIO must be at 3.3 V for USB Full-Speed signal compliance per the USB 2.0 specification. Power-rail sequencing (VDDIN before VDDIO) is recommended to avoid latch-up; consult the SAME51 datasheet DS60001506 for full power-rail sequencing diagrams.
The 100-pin TQFP package has a thermal resistance θJA of approximately 31 °C/W (still-air, JEDEC 4-layer PCB). At maximum CPU activity (120 MHz, all peripherals active), the E51 consumes roughly 100 mW, resulting in a junction-temperature rise of about 3 °C above ambient - well within the 85 °C industrial limit. For designs operating at +85 °C ambient with minimal airflow, however, headroom drops to zero. Add a thermal copper pour under the exposed pad (TQFP-100 has no exposed pad; use copper-filled GND pour instead) and avoid placing heat-generating components directly above the MCU. Derating 20% of maximum CPU activity is recommended for high-ambient industrial deployments.
Route the 50 MHz external crystal traces (XIN/XOUT) as short as possible (under 10 mm) with a ground guard trace on each side to prevent crosstalk into the ADC inputs. Place the 12 pF crystal load capacitors within 3 mm of the XIN/XOUT pins. For the USB DP/DM differential pair, maintain 90 Ω differential impedance with matched trace lengths (within 2 mm) and keep the pair clear of noisy traces (PWM, switching regulator). All SERCOM signals can be remapped to alternate pads via the I/O multiplexing controller; use the Atmel START pin mux tool to verify pin assignment conflicts before PCB layout freeze.
Estimated: programming firmware to the ATSAME51N19A-AU without setting the GCLK_CONFIG and SUPC.VREF settings correctly can cause the PLL to fail lock at 120 MHz - always boot from the 12 MHz internal oscillator and let the DFLL lock first before switching to PLL. A common pitfall is configuring the SERCOM baud rate generator without accounting for the SERCOM GCLK source - the SERCOM clock must be at least 2x the desired baud rate. Also, when migrating from SAM D51 to SAM E51 firmware, verify that crypto-related PORT mappings do not conflict with the application-defined GPIO layout, as the E51 has additional SERCOM/IOC pins not present on the D51. TrustZone-M secure attribute configuration errors will silently break interrupt vector routing - always verify in the SAME51 device family pack examples.
تعمیل کی معلومات
RoHS and REACH compliance per Microchip product page. AEC-Q100 not applicable - this is an industrial-grade part (-40°C to +85°C); for automotive AEC-Q100 qualified parts see SAM E51J variants. Lead-free and matte-tin finish per Microchip manufacturing standards.
