BTH60702EPVXUMA1 - 60 mΩ Dual High-Side Switch 1.7A | Infineon
MPN: BTH60702EPVXUMA1 ✓ فعالBTH60702EPVXUMA1 جائزہ
A high-side switch is a power distribution switch that sits between the supply rail and the load, allowing the load to be turned on/off by a low-voltage control signal while protecting the wiring harness from faults such as over-current, short-circuit, over-voltage, and reverse battery. Within the broader component taxonomy, the BTH60702EPVXUMA1 sits in the smart high-side switch (intelligent power switch, IPS) family, which descends from discrete MOSFETs and power distribution switches and integrates them with logic, sense, and protection in a single device. This integration reduces PCB area, simplifies wiring harness design, and improves diagnostic coverage in body and powertrain ECUs.
Key features include a typical on-state resistance of 60 mΩ per channel, dual independent 1:1 N-channel outputs, current-sense analog feedback for load diagnosis, integrated charge pump for full N-channel drive, and protection against over-load, short-circuit, over-voltage, reverse battery, and thermal shutdown. The PG-TSDSO-14 package with exposed pad provides a low thermal resistance path that sustains 1.7 A continuous per channel in automotive temperature classes.
Typical applications include automotive lighting (headlamps, tail lamps, indicator LEDs), resistive and inductive body loads (seat heaters, mirror heaters, washer pumps), 48 V board-net zonal modules, and zone-ECU power distribution in mild-hybrid and 48 V vehicles. The device's current-sense output also enables predictive maintenance and open-load detection at standstill.
When designing with this part, ensure that the exposed pad is soldered to a sufficiently large copper area (typically 1 cm² or more) to keep junction temperature within the automotive -40 °C to +150 °C range under worst-case load. The IN pins of both channels should be tied to the same supply; if independent supplies are required, two separate BTH6070-2EPV devices must be used.
This page synthesizes distributor stock, drop-in same-family cross-references, and application guidance not found in the manufacturer datasheet alone.
کے لیے ڈراپ اِن متبادل BTH60702EPVXUMA1 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں BTH60702EPVXUMA1 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Operating Voltage Range, Number of Channels, On-State Resistance (RDS(on)), Protection Features.
BTH60801EPLXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS51202EKAXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS3256DAUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS70402EPGXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTG7003A1EPWXUMA2
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTH60702EPVXUMA1 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Manufacturer | Infineon Technologies |
| Product Family | PROFET + 48V |
| فنکشن | Smart high-side power switch (dual channel, 2 x 1:1) |
| On-State Resistance (typ.) | 60 mΩ per channel |
| Continuous Load Current (per channel) | 1.7 A |
| Number of Channels | 2 |
| Configuration | 2 x 1:1 (dual independent high-side) |
| ٹرانزسٹر کی قسم | N-channel vertical power MOSFET with charge pump |
| Nominal Operating Voltage | 48 V board net |
| Maximum Supply Voltage | 54 V |
| Current Sense / Diagnosis | Yes (analog current-sense output) |
| Protection Features | Over-load, short-circuit, over-voltage, reverse battery, thermal shutdown |
| پیکیج | PG-TSDSO-14 with exposed pad |
| Operating Temperature (junction) | -40 °C to +150 °C (automotive grade) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| RoHS اسٹیٹس | Compliant |
BTH60702EPVXUMA1 پن کنفیگریشن
| پن 1 | OUT1 — Channel 1 high-side output to load |
| پن 2 | IN1 — Channel 1 input control signal (active-high or active-low per variant) |
| پن 3 | GND — Ground |
| پن 4 | VBB — Supply voltage (48 V board net) |
| پن 5 | IS — Current sense / diagnostic output |
| پن 6 | DEN — Diagnostic enable |
| پن 7 | OUT2 — Channel 2 high-side output to load |
| پن 8 | IN2 — Channel 2 input control signal |
| پن 9 | GND — Ground |
| پن 10 | VBB — Supply voltage (48 V board net) |
| پن 11 | NC — Not connected (per datasheet) |
| پن 12 | NC — Not connected (per datasheet) |
| پن 13 | NC — Not connected (per datasheet) |
| پن 14 | Exposed Pad — Thermal pad; tie to copper pour for heat dissipation |
محفوظ آپریٹنگ ایریا - High-Side Switch
عام استعمالات
BTH60702EPVXUMA1 کے لیے موزوں ہے 6 ایپلیکیشنs: 48 V Automotive Lighting, 48 V Body Load Switching (Heaters, Pumps, Mirrors), Mild-Hybrid 48 V Zonal ECU Power Distribution, 48 V Auxiliary Load Switching (Fans, Valves, Actuators), Battery Management Protection (48 V Li-ion Packs), Industrial 48 V Power Distribution.
48 V Automotive Lighting
The BTH60702EPVXUMA1 drives 48 V LED headlamp and tail-lamp modules from a zonal ECU, where its 60 mΩ RDS(on) keeps conduction dissipation to roughly 0.17 W per channel at 1.7 A and its 54 V transient tolerance handles load-dump events on the 48 V rail. Two independent 1:1 channels let one device drive both the low-beam and high-beam LED strings from a single IC, simplifying the harness and reducing PCB area. The integrated analog current-sense output enables open-string and partial-short detection during ECU diagnostics, supporting ASIL-aware functional safety. Compared with a discrete MOSFET + fuse approach, this smart high-side switch consolidates protection, sense, and drive in a single 14-pin PG-TSDSO package.
تجویز کردہ
48 V Body Load Switching (Heaters, Pumps, Mirrors)
Resistive and inductive body loads such as seat heaters, mirror heaters, and washer pumps are driven directly by the BTH60702EPVXUMA1 from a 48 V supply. The device's over-load and short-circuit protection allow safe handling of motor stall currents without external fusing, while the current-sense pin reports the actual load current to the body-domain ECU for fault detection and predictive service. The exposed-pad PG-TSDSO-14 package sustains 1.7 A per channel continuously on a typical FR-4 PCB with 1 cm² of copper, fitting the compact form factor of modern zonal modules. Two channels per package reduce BOM count in body ECUs that switch many similar loads.
تجویز کردہ
Mild-Hybrid 48 V Zonal ECU Power Distribution
In mild-hybrid 48 V zonal ECU architectures, the BTH60702EPVXUMA1 distributes power from the 48 V bus to multiple downstream loads and downstream converters. Its 54 V maximum supply rating tolerates transient overshoot typical of 48 V board nets under load dump, and its reverse-battery protection eliminates the need for an external reverse-polarity FET. The two independent channels let one IC serve two distinct downstream rails, simplifying the harness and reducing PCB area in space-constrained zonal modules. Current-sense feedback supports ECU-level energy management and load monitoring required by mild-hybrid operating strategies.
تجویز کردہ
48 V Auxiliary Load Switching (Fans, Valves, Actuators)
Auxiliary 48 V loads such as cooling fans, solenoid valves, and small actuators in mild-hybrid powertrains are switched by the BTH60702EPVXUMA1. The smart high-side switch handles inrush currents of fans and inductive kickback of solenoids via integrated protection, eliminating external freewheel diodes in many cases. Two channels can drive a fan and a valve from one IC, simplifying PCB layout. The exposed-pad package keeps thermal rise modest at 1.7 A continuous, while the diagnostic current-sense output lets the powertrain ECU detect failing fans or stuck valves. Compared with electromechanical relays, this solid-state solution is silent, faster, and supports PWM-based fan-speed control.
تجویز کردہ
Battery Management Protection (48 V Li-ion Packs)
Inside 48 V Li-ion battery management systems, the BTH60702EPVXUMA1 can serve as a high-side disconnect and precharge path element, where its 54 V rating covers the fully charged 48 V pack and its over-voltage clamp protects downstream ASICs. The current-sense pin supports accurate pack-current measurement during precharge and normal operation, while integrated thermal shutdown protects against pack-fault conditions. Two channels can route the main discharge path and a redundant precharge path. The PG-TSDSO-14 footprint suits compact BMS PCBs that integrate with the cell-monitoring ASICs.
تجویز کردہ
Industrial 48 V Power Distribution
Beyond automotive, the BTH60702EPVXUMA1 fits industrial 48 V power distribution systems, such as 48 V telecom racks, 48 V solar battery banks, and 48 V robotics buses. Its high-side topology, current-sense output, and protection suite give designers the same diagnostic and protection advantages enjoyed by automotive users, while its 54 V tolerance handles industrial transients. Two independent 1.7 A channels can switch multiple downstream rails from a single IC. The exposed-pad PG-TSDSO-14 package simplifies thermal management in enclosed industrial enclosures with limited airflow.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا BTH60702EPVXUMA1 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | BTH60801EPLXUMA1 | BTS51202EKAXUMA1 | BTS3256DAUMA1 | BTS70402EPGXUMA1 | BTG7003A1EPWXUMA2 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TSDSO-14 (exposed pad) | PG-TSDSO-14 (exposed pad) - same family | PG-DSO-20 | PG-DSO-20 | PG-DSO-20 | PG-TSDSO-14 |
| Nominal Supply Voltage | 48 V | 48 V | 12 V | 12 V / 24 V | 12 V | 48 V |
| Current Sense / Diagnosis | Yes (analog) | Yes | Yes | Yes | Yes | Yes |
| Automotive Grade | Yes (PROFET + 48V) | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- 48 V board-net native design (بمقابلہBTS51202EKAXUMA1)
- Dual 1:1 independent channels in one package (بمقابلہBTH60801EPLXUMA1)
- Integrated analog current-sense diagnosis (بمقابلہDiscrete MOSFET + fuse)
ڈیزائن نوٹس
Estimated: at 1.7 A per channel on both channels and VIN = 48 V, conduction loss is approximately 2 × I² × R = 2 × 1.7² × 0.06 = 0.35 W. With a typical PG-TSDSO-14 exposed-pad theta_JA in the 30-40 C/W range on 1 cm² of 1 oz copper, junction temperature rise above ambient is roughly 10-14 °C, well within the 150 °C limit. For higher current or higher ambient, increase copper area or add thermal vias to inner planes. Always validate with a thermal camera on the final assembly.
Solder the exposed pad of the PG-TSDSO-14 to a copper pour of at least 1 cm² to meet thermal and electrical performance. Place the VBB decoupling capacitors (typically 100 nF ceramic + 10 µF electrolytic) within 5 mm of the VBB pins to suppress supply transients from the 48 V board net. Route the high-current OUT traces with wide, short copper pours; minimize loop inductance to keep switching transients within the device's over-voltage clamp window. Keep the IS (current-sense) trace short and away from noisy switching nodes to preserve diagnostic accuracy.
Do not parallel the two channels of one BTH60702EPVXUMA1 to double the current - the channels share thermal paths but have independent current limiting, so imbalance will occur. Do not operate the device without the exposed pad soldered; thermal shutdown will trigger prematurely. Do not connect IN1 and IN2 to different supply rails - both channels share VBB and require common supply. For 12 V designs, consider the BTS51202EKAXUMA1 family instead of using this 48 V part, as the RDS(on) is optimized for 48 V and may be unnecessarily high for 12 V applications.
تعمیل کی معلومات
AEC-Q100 qualified per Infineon PROFET + 48V product family. RoHS compliant. Halogen-free. Pb-free reflow-compatible.
