CS5503-BP - 20-Bit 4 kSps ADC | Cirrus Logic | Sensor Measurement
MPN: CS5503-BP ✗ اختتامِ زندگیCS5503-BP جائزہ
An ADC is a data-acquisition IC that converts an analog input voltage into a numeric value for processing by a microcontroller, DSP, or other digital controller. The CS5503 belongs to the CMOS ADC hierarchy, where resolution describes the number of digital bits in each conversion result and conversion rate defines how rapidly those results are produced. The CS5503 emphasizes high resolution and moderate speed rather than high-bandwidth waveform acquisition.
Principal features include 20-bit resolution, operation at up to 4 kSps word rate, charge-balance conversion, a 6-pole Gaussian low-pass filter, and on-chip self-calibration circuitry. These characteristics make the converter suitable for slow but precise measurements where physical, chemical, biological, or industrial sensor outputs must be digitized. The integrated filter reduces unwanted high-frequency content before the conversion result is transferred to the digital side.
The charge-balance architecture supports accurate conversion of low-frequency signals, while the digital output can be selected according to the system clock and application requirements. On-chip self-calibration can be initiated at different times or temperatures to help maintain offset and full-scale accuracy. The available datasheet material describes typical calibration errors of less than one-half LSB for the relevant converter family, although application-specific limits should be confirmed against the complete operating conditions.
Typical uses include temperature and pressure sensor acquisition, industrial process monitoring, laboratory instrumentation, and low-speed chemical or biological measurement systems. The CS5503 is most appropriate when 20-bit numeric resolution, on-chip filtering, and conversion rates up to 4 kSps are sufficient, but the input bandwidth is not the primary constraint.
Designers should provide a suitable external clock or crystal, observe the required bypass and grounding practices, and allow adequate settling time for analog and digital supply rails. Because the verified source does not publish complete supply-voltage, reference-voltage, current-consumption, or operating-temperature tables, those values must be verified in the manufacturer datasheet before schematic release.
This product page combines verified converter specifications, practical application guidance, source-backed availability information, and package information that helps engineers determine whether the CS5503-BP fits a precision, low-frequency measurement design before committing to a PCB layout.
کے لیے ڈراپ اِن متبادل CS5503-BP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںCS5503-BP زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| ADC Resolution | 20 bit |
| Maximum Output Word Rate | 4 kSps |
| Conversion Architecture | Charge balance |
| Integrated Filter | 6-pole low-pass Gaussian filter |
| Process Technology | CMOS |
| Self-Calibration | On-chip, user-initiated |
| Typical Offset and Full-Scale Error | Less than 0.5 LSB |
| پیکیج | PDIP-20 |
| ماؤنٹنگ ٹائپ | Through-hole |
| RoHS اسٹیٹس | Compliant |
| Clock Requirement | External CMOS clock or crystal |
CS5503-BP pdip-20 پن کنفیگریشن گائیڈ
CS5503-BP (pdip-20 پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں CS5503-BP.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
CS5503-BP کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Process Sensor Acquisition, Temperature and Pressure Instrumentation, Chemical and Biological Test Systems, Precision Weighing and Force Measurement, Environmental Monitoring Equipment, Laboratory Data-Acquisition Systems.
Industrial Process Sensor Acquisition
The CS5503-BP fits low-speed industrial measurement systems that require more numeric detail than a conventional 16-bit converter can provide. Its 20-bit resolution and conversion rate of up to 4 kSps are suitable for pressure, level, flow, and temperature signals that change slowly relative to the sampling period. The 6-pole on-chip Gaussian filter helps attenuate high-frequency noise before digital processing, while user-initiated self-calibration supports offset and full-scale control. Engineers must still verify the complete input range, reference configuration, supply limits, and calibration schedule against the manufacturer datasheet.
تجویز کردہ
Temperature and Pressure Instrumentation
CS5503-BP is appropriate for precision temperature or pressure acquisition when the analog sensor produces a relatively slow, narrow-band signal. A 20-bit result provides 1,024 code levels more than a 16-bit converter, while the available 4 kSps word rate is more than sufficient for many thermal and pressure loops. Its integrated 6-pole Gaussian low-pass filter can reduce electrical noise surrounding the sensor output. The main design checks are analog excitation, input conditioning, reference stability, and ensuring that filtering delay is acceptable for the intended measurement bandwidth.
تجویز کردہ
Chemical and Biological Test Systems
The CS5503-BP can digitize low-frequency chemical or biological sensor outputs where resolution and rejection of unwanted high-frequency content matter more than acquisition speed. The manufacturer describes the CS5503 as a 20-bit charge-balance CMOS ADC intended for physical, chemical, and biological processes, with conversion rates up to 4 kSps. Its on-chip 6-pole Gaussian filter and self-calibration circuitry simplify analog front-end design. For laboratory or diagnostic equipment, engineers should verify noise, linearity, settling time, and reference requirements for the complete signal chain before selecting external filter components.
تجویز کردہ
Precision Weighing and Force Measurement
CS5503-BP is suitable for load-cell, force, and weighing systems when the mechanical signal changes slowly and the system benefits from high-resolution digitization. The 20-bit conversion result and maximum 4 kSps word rate provide a useful balance between numerical precision and responsiveness, while the integrated Gaussian filter can suppress high-frequency mechanical and electrical disturbances. For strain-gage bridges, the ADC should be paired with a suitably stable excitation and low-noise analog front end. Baseline offset, gain calibration, warm-up behavior, and the manufacturer-recommended self-calibration timing require system-level verification.
تجویز کردہ
Environmental Monitoring Equipment
CS5503-BP supports environmental monitoring instruments that combine several slow analog sensors, such as humidity, gas, pressure, and ambient-temperature channels. Its 20-bit resolution preserves fine changes in slowly varying readings, and conversion rates up to 4 kSps provide flexibility in multiplexing and control-loop response. The 6-pole on-chip low-pass Gaussian filter helps reject noise outside the intended measurement bandwidth. Because the verified data does not include input multiplexing details, channel count, supply specifications, or environmental ratings, an engineer must confirm those parameters in the complete Cirrus Logic datasheet before finalizing the instrument architecture.
تجویز کردہ
Laboratory Data-Acquisition Systems
The CS5503-BP can serve as the measurement ADC in a laboratory instrument for low-frequency analog signals requiring 20-bit numerical resolution. Its charge-balance architecture, 6-pole Gaussian filter, and on-chip self-calibration provide useful features for precision data acquisition without requiring a separate digital filtering stage. A 4 kSps maximum word rate is appropriate for temperature, pressure, force, and many chemical sensor channels, although it is not suitable for high-bandwidth oscilloscope acquisition. The analog reference, input range, clock arrangement, digital interface, and supply sequencing must be implemented according to the manufacturer datasheet.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا CS5503-BP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Package | PDIP-20 |
| Brand | Cirrus Logic |
| ADC Resolution | 20 bit |
| Maximum Output Word Rate | 4 kSps |
| Conversion Architecture | Charge balance |
| Integrated Filter | 6-pole low-pass Gaussian filter |
| Process Technology | CMOS |
| Self-Calibration | On-chip, user-initiated |
| Verified Price | $3.4805 as of 2026-10-30 |
| RoHS Status | Compliant |
اہم امتیازی خصوصیات
- Higher conversion resolution than the CS5501 family member (بمقابلہCS5501-BP)
- Retains the original PDIP-20 footprint (بمقابلہCS5503-BS)
- Integrated digital-noise filtering (بمقابلہCS5501-BP)
ڈیزائن نوٹس
Route the analog input, reference, and converter clock as short, quiet nets, and place associated bypass components directly at their associated pins. Keep digital interface traces away from the analog input and reference paths. The verified information identifies an external CMOS clock or crystal as the sampling source, so the clock layout should prevent coupling from switching nodes into the charge-balance converter.
Treat the 6-pole Gaussian filter as part of the complete signal-path bandwidth rather than as an independent specification. Its settling behavior affects the usable sampling rate and measurement latency. Confirm the permitted clock range and output word rate in the complete manufacturer datasheet, and validate filter delay against any control-loop or data-acquisition timing requirement.
Do not substitute CS5501-BP or CS5503-BS as a direct PCB replacement. CS5501-BP has a PDIP-16 package and 16-bit resolution, while CS5503-BS is available in 20-SOIC. The verified cross-reference data does not identify another part with the same PDIP-20 footprint and pin compatibility, so any redesign requires a new land pattern and complete pin-level review.
Verify supply-voltage limits, analog and digital current consumption, and reference requirements before assigning capacitors or designing power rails. These values are not present in the supplied source excerpts. Use the values and application guidance from the manufacturer datasheet rather than estimating rail headroom or bypassing the missing electrical limits.
تعمیل کی معلومات
RoHS compliance is identified in the verified distributor data. No verified REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was supplied. AEC-Q100 is treated as not applicable because the device is an industrial and consumer measurement ADC rather than an automotive-qualified component.
