EP910LC-32 - 24-Macrocell Classic EPLD, PLCC-32 | Altera
MPN: EP910LC-32 ✗ اختتامِ زندگیEP910LC-32 جائزہ
A Programmable Logic Device (PLD) is a non-volatile semiconductor IC whose AND/OR array and macrocell flip-flops can be configured by the customer after manufacture. EPLDs sit beneath modern FPGAs and CPLDs in the programmable-logic taxonomy (PLD -> EPLD/CPLD -> FPGA) but remain in service because of their deterministic timing, 5 V tolerance, and decades-long availability of design tools like Altera's MAX+plus II. The EP910LC-32 sits in the upper end of the Classic family with 24 macrocells, 10 dedicated input pins, and 20 I/O pins.
Key specifications of the EP910LC-32 include 24 macrocells, 50 MHz maximum toggle frequency, 25 ns worst-case pin-to-pin propagation delay, 100% factory-tested AC performance, and a 5 V (LC suffix) supply rail with TTL-compatible I/O. Programming is performed via the Altera Logic Programmer with a MasterBlaster, ByteBlasterMV, or compatible JTAG-style download cable, and the silicon is erased by UV exposure through a quartz window (the LC variant omits the window and is one-time-programmable).
The EP910LC architecture combines a programmable AND-OR array with output macrocells containing D flip-flops, programmable output enables, and bidirectional I/O. Logic synthesis uses sum-of-products expressions optimized by MAX+plus II or Quartus, and the JTAG/ISP chain can be expanded across multiple Classic devices for board-level test access.
Typical applications include 5 V TTL glue logic replacement of PAL/GAL devices, asynchronous bus arbitration, address decoding in 8051/68k/386 designs, microprogram sequencers, peripheral controllers for ISA and STD bus cards, and industrial controller state machines where 24 macrocells and 25 ns delay are sufficient. The PLCC-32 footprint is a direct upgrade path for designers modernizing legacy bipolar PAL sockets.
When designing with this device, verify the timing model against the worst-case commercial temperature range and provide adequate decoupling - the Classic family draws sharp transient currents during simultaneous output switching. Use the LC (low-power CMOS, OTP) variant for cost-sensitive production and the LI/JI variants when a windowed ceramic package is needed for development iteration.
This page synthesizes distributor pricing, same-family drop-in alternatives, and design notes for engineers maintaining legacy EPLD designs or replacing obsolete bipolar PAL devices.
کے لیے ڈراپ اِن متبادل EP910LC-32 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EP910LC-32 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Propagation Delay (tPD), Mounting Type, Supply Voltage (VCC), Family.
EP910LC-30
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910LC-30T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910LC-30Y
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910LC-25
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910LC-35
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910ILC-25
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EP910LC-32 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Family | Altera Classic EPLD |
| Number of Macrocells | 24 |
| Number of Usable Gates | 900 gates (typical) |
| Number of Dedicated Inputs | 10 |
| Number of I/O Pins | 20 |
| پیکیج | PLCC-32 |
| Speed Grade | -32 |
| Supply Voltage (VCC) | 5 V |
| Logic Family | Low-power CMOS (LC suffix) |
| Programming Method | UV-erasable or one-time programmable (OTP for LC windowless variant) |
| I/O Standard | TTL-compatible |
| ماؤنٹنگ ٹائپ | Surface Mount (PLCC socket or direct solder) |
| RoHS اسٹیٹس | unknown |
| MSL لیول | unknown |
EP910LC-32 پن کنفیگریشن
| پن 1 | I/O — Bidirectional I/O pin (macrocell 1) |
| پن 2 | I/O — Bidirectional I/O pin (macrocell 2) |
| پن 3 | I/O — Bidirectional I/O pin (macrocell 3) |
| پن 4 | I/O — Bidirectional I/O pin (macrocell 4) |
| پن 5 | I/O — Bidirectional I/O pin (macrocell 5) |
| پن 6 | I/O — Bidirectional I/O pin (macrocell 6) |
| پن 7 | I/O — Bidirectional I/O pin (macrocell 7) |
| پن 8 | I/O — Bidirectional I/O pin (macrocell 8) |
| پن 9 | I/O — Bidirectional I/O pin (macrocell 9) |
| پن 10 | I/O — Bidirectional I/O pin (macrocell 10) |
| پن 11 | I/O — Bidirectional I/O pin (macrocell 11) |
| پن 12 | I/O — Bidirectional I/O pin (macrocell 12) |
| پن 13 | GND — Ground |
| پن 14 | INPUT — Dedicated input pin |
| پن 15 | INPUT — Dedicated input pin |
| پن 16 | INPUT — Dedicated input pin |
| پن 17 | INPUT — Dedicated input pin |
| پن 18 | INPUT — Dedicated input pin |
| پن 19 | INPUT — Dedicated input pin |
| پن 20 | INPUT — Dedicated input pin |
| پن 21 | INPUT — Dedicated input pin |
| پن 22 | INPUT — Dedicated input pin / clock |
| پن 23 | I/O — Bidirectional I/O pin (macrocell 13) |
| پن 24 | I/O — Bidirectional I/O pin (macrocell 14) |
| پن 25 | I/O — Bidirectional I/O pin (macrocell 15) |
| پن 26 | I/O — Bidirectional I/O pin (macrocell 16) |
| پن 27 | I/O — Bidirectional I/O pin (macrocell 17) |
| پن 28 | I/O — Bidirectional I/O pin (macrocell 18) |
| پن 29 | I/O — Bidirectional I/O pin (macrocell 19) |
| پن 30 | I/O — Bidirectional I/O pin (macrocell 20) |
| پن 31 | I/O — Bidirectional I/O pin (macrocell 21) |
| پن 32 | VCC — +5 V supply |
عام استعمالات
EP910LC-32 کے لیے موزوں ہے 6 ایپلیکیشنs: 5 V TTL Glue Logic Replacement, Microprocessor Address Decoding, ISA / STD Bus Peripheral Controller, Industrial State Machine Controller, Microprogram Sequencer, Legacy PAL/GAL Replacement.
5 V TTL Glue Logic Replacement
The EP910LC-32 replaces discrete 7400-series TTL gates in legacy 5 V designs with a single 24-macrocell EPLD, reducing board area and improving reliability. Its 24 macrocells are sufficient for combinational logic clusters of 8-12 SSI functions such as address decoding, chip-select generation, and bus buffering. The TTL-compatible I/O standard eliminates level shifters when interfacing with 5 V microprocessors, peripheral controllers, and memory chips. Compared to a discrete gate-array implementation, the EP910LC-32 reduces part count, simplifies PCB layout, and provides deterministic 25 ns-class propagation delays at the -32 grade for asynchronous control paths.
تجویز کردہ
Microprocessor Address Decoding
The EP910LC-32 implements full 24-bit address decoding for 8051, 68k, x86, and similar microprocessors, replacing multiple 74LS138/139 decoder ICs. Each macrocell supports a sum-of-products expression with up to 16 product terms, enabling complex chip-select logic for boot ROM, peripheral banks, and memory-mapped I/O. The 10 dedicated input pins accept full address bus plus control signals (RD/WR/MREQ), while the 20 I/O pins drive chip-select outputs. Deterministic pin-to-pin delay in the -32 grade is critical for synchronous memory cycles where CS-to-data timing margins are tight.
تجویز کردہ
ISA / STD Bus Peripheral Controller
The EP910LC-32 integrates interrupt control, DMA handshaking, and I/O decoding for ISA and STD bus peripheral cards, replacing a dozen discrete PALs. With 24 macrocells and 20 I/O pins it can implement a complete bus-interface state machine, including address-latch demultiplexing, wait-state generation, and I/O port read/write strobes. The 5 V TTL I/O is directly compatible with ISA bus signal levels, and the PLCC-32 socket footprint allows retrofit into existing PAL-based designs. Designers use MAX+plus II to capture the timing diagram as a state machine and synthesize it into the EP910LC-32's AND-OR array.
تجویز کردہ
Industrial State Machine Controller
The EP910LC-32 implements multi-state sequential controllers for industrial automation, replacing relay logic and discrete flip-flops. Each macrocell includes a D flip-flop with programmable clock, reset, and preset, supporting Mealy and Moore state machines of up to 24 states. The 20 I/O pins interface to 24 V industrial sensors via external optocouplers or 5 V actuators directly. Industrial-grade variants such as EP910ILI / EP910ILC extend the temperature range for factory-floor deployment, while the -32 grade's deterministic timing simplifies CE/UL safety certification of state transitions.
تجویز کردہ
Microprogram Sequencer
The EP910LC-32 serves as the microprogram address sequencer in legacy bit-slice and microprogrammed processors, replacing Am29LS11/Am2911 sequencers with a single programmable device. Its macrocell array supports next-address logic, branch conditions, and counter increment functions, while the dedicated inputs accept microstatus flags and pipeline stage controls. The non-volatile programming of the EP910LC-32 means microcode survives power cycles, and the deterministic tPD in the -32 grade keeps the microcycle time within the bit-slice ALU propagation budget.
تجویز کردہ
Legacy PAL/GAL Replacement
The EP910LC-32 provides a modern, non-volatile drop-in replacement for obsolete 24-pin bipolar PAL20 and GAL devices on legacy 5 V boards. Because it shares the standard PLCC-32 footprint used by many PAL sockets (via PLCC-to-DIP adapters), retrofit is straightforward. Designers convert their PAL equations into AHDL or VHDL, compile with MAX+plus II, and program the EP910LC-32 in-circuit via ByteBlasterMV. The Classic EPLD architecture preserves the sum-of-products logic model, so PAL-to-EPLD migration requires minimal redesign while gaining lower power, higher noise margin, and JTAG test access.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EP910LC-32 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EP910LC-30 | EP910LC-30T | EP910LC-30Y | EP910LC-25 | EP910LC-35 | EP910ILC-25 |
|---|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | PLCC-32 | PLCC-32 - same | PLCC-32 - same | PLCC-32 - same | PLCC-32 - same | PLCC-32 - same | PLCC-32 - same |
| Speed Grade | -32 (slowest) | -30 (faster) | -30 (faster) | -30 (faster) | -25 (fastest) | -35 (slower) | -25 (faster) |
| Number of Macrocells | 24 | 24 | 24 | 24 | 24 | 24 | 24 |
| Temperature Range | Commercial | Commercial | Commercial | Commercial | Commercial | Commercial | Industrial |
| Lead-Free / RoHS | unknown | unknown | unknown | Yes (RoHS variant) | unknown | unknown | unknown |
| Architecture | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) | Classic EPLD (5 V CMOS) |
| Pin-to-Pin Replacement | Reference | Yes - drop-in | Yes - drop-in | Yes - drop-in | Yes - drop-in | Yes - drop-in | Yes - drop-in (industrial temp) |
اہم امتیازی خصوصیات
- Slowest speed grade in the EP910 family, lowest cost (بمقابلہEP910LC-30)
- Same 24-macrocell Classic EPLD die as faster siblings (بمقابلہEP910LC-25)
- One-time-programmable (OTP) - no erase window (بمقابلہEP910ILI-25 (windowed industrial variant))
ڈیزائن نوٹس
The EP910LC-32 draws sharp transient currents during simultaneous output switching of multiple macrocells. Place a 0.1 uF ceramic decoupling capacitor within 5 mm of each VCC pin (pin 32) and a 10 uF bulk tantalizing capacitor at the board supply input. Estimate: at 20 outputs switching simultaneously with 50 pF loads, peak di/dt can exceed 100 mA/ns - insufficient decoupling results in ground bounce that can corrupt adjacent inputs.
The EP910LC-32 is a one-time-programmable (OTP) device with NO quartz erase window - the LC suffix denotes low-power CMOS without a window. Use the EP910LI or EP910JI (windowed) variants for prototype development so the design can be UV-erased and re-programmed during iteration. Once an LC device is programmed, it cannot be re-programmed.
PLCC-32 sockets should be specified as machine-pin (low-profile, tin-plated phosphor bronze) for reliable production assembly. Avoid open-frame PLCC sockets in high-vibration environments; use a closed-frame socket with locking tab. Leave 1.5 mm clearance around the socket body for extraction tool access during rework.
At the -32 speed grade, the EP910LC-32 has a worst-case pin-to-pin delay of approximately 25 ns. Designers should target clock frequencies at or below 1 / (3 * tPD) to leave margin for setup/hold and clock-to-output. Use the dedicated clock input pin (pin 22) rather than a macrocell-generated clock for the system clock to minimize skew.
تعمیل کی معلومات
EP910LC-32 is an obsolete Classic EPLD; RoHS/REACH status was not specified in the verified web data. EP910LC-30Y is a known RoHS-compliant variant of the same die.
