EPM5064LC-2 - 64-Macrocell MAX 5000 CPLD, 45ns, PLCC44 | Altera
MPN: EPM5064LC-2 ✗ اختتامِ زندگیEPM5064LC-2 جائزہ
A Complex Programmable Logic Device (CPLD) is a non-volatile programmable logic IC that combines multiple PAL-like macrocell arrays on a single die with a programmable interconnect matrix. The MAX 5000 architecture uses CMOS EPROM / UV-erasable cells (OTP variants denoted "LC" use one-time-programmable EPROM) to retain the configuration without a separate boot memory. CPLDs sit in the broader hierarchy of programmable logic: simple PLD (PAL/GAL) -> CPLD -> FPGA, and are preferred over FPGAs when deterministic pin-to-pin timing, instant-on behavior, and a small fixed logic capacity are sufficient.
Key features of the EPM5064LC-2 include: 64 macrocells, 36 inputs, 28 I/O pins, 4 logic array blocks (LABs) each containing 16 macrocells, 45 ns combinational propagation delay (tPD), 40 MHz maximum internal frequency, and a programmable AND/OR array with per-macrocell flip-flop (D/T/JK/SR). Programming is performed via a JTAG-compatible or Altera-proprietary byte-wide programmer, and the device is OTP (one-time programmable) in the LC variant.
Typical applications include legacy glue-logic replacement, address decoding and bus-interface adaptation, state-machine controllers in industrial control boards, and pin-compatible second-source designs for MAX 5000 sockets. The LC-2 speed grade is one bin slower than LC-1 and is often chosen where timing margin is acceptable and lower-cost / wider-availability parts are preferred.
When designing with the EPM5064LC-2, plan for 4.75 V to 5.25 V single-supply operation, add 0.1 uF + 1 uF decoupling near each VCC/ GND pair, and verify timing with Altera MAX+PLUS II timing analysis. Confirm second-source availability before committing to the LC OTP process flow.
This page consolidates distributor pricing, drop-in same-package alternatives, and design notes for engineers maintaining MAX 5000 designs — context not present in the original datasheet PDF.
کے لیے ڈراپ اِن متبادل EPM5064LC-2 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM5064LC-2 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Supply Voltage (VCC), Process Technology, Propagation Delay (tPD), Usable Gates.
EPM5064LC-1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064LC
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064JC-2
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064JC-1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064JC
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064JC1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064JI-1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5064LC-2 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Family | MAX 5000 |
| Product Type | CPLD (Complex Programmable Logic Device) |
| Macrocells | 64 |
| Logic Array Blocks (LABs) | 4 |
| Logic Elements per LAB | 16 |
| Number of Inputs | 36 (7 dedicated + 28 I/O) |
| Number of I/O Pins | 28 |
| Number of Flip-Flops | 28 |
| Propagation Delay (tPD) | 45 ns |
| Maximum Internal Frequency | 40 MHz |
| Process Technology | CMOS, OTP EPROM (UV-erasable base) |
| Programmable Polarity | Yes |
| Programmable Output Enable | Yes, per macrocell |
| Supply Voltage (VCC) | 4.75 V to 5.25 V (5 V nominal) |
| پیکیج | PLCC-44 (J-Lead, plastic) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Programming Method | Altera byte-wide / JTAG programmer |
EPM5064LC-2 پن کنفیگریشن
| پن 1 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 2 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 3 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 4 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 5 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 6 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 7 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 8 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 9 | I/O — Bidirectional user I/O pin (LAB A) |
| پن 10 | GND — Ground |
| پن 11 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 12 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 13 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 14 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 15 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 16 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 17 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 18 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 19 | I/O — Bidirectional user I/O pin (LAB B) |
| پن 20 | GND — Ground |
| پن 21 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 22 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 23 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 24 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 25 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 26 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 27 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 28 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 29 | I/O — Bidirectional user I/O pin (LAB C) |
| پن 30 | GND — Ground |
| پن 31 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 32 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 33 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 34 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 35 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 36 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 37 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 38 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 39 | I/O — Bidirectional user I/O pin (LAB D) |
| پن 40 | GND — Ground |
| پن 41 | IN — Dedicated input pin |
| پن 42 | IN — Dedicated input pin |
| پن 43 | IN — Dedicated input pin |
| پن 44 | VCC — +5 V supply |
عام استعمالات
EPM5064LC-2 کے لیے موزوں ہے 7 ایپلیکیشنs: Legacy Glue-Logic Replacement, Address Decoding & Bus Interface Adaptation, State-Machine Controllers, Pin-Compatible Second Source for MAX 5000 Sockets, Industrial Control Board Repair, Educational & Legacy Development Boards, 5 V Instrumentation Front-End Logic.
Legacy Glue-Logic Replacement
The EPM5064LC-2's 64 macrocells, 36 inputs, and 45 ns propagation delay make it a direct replacement for clusters of discrete PAL/GAL chips on older 5 V industrial boards. Its deterministic pin-to-pin timing lets engineers consolidate multiple small PLDs into one CPLD without changing the bus-cycle budget; 4 LABs of 16 macrocells each allow up to 64 sum-of-product terms with per-macrocell flip-flops. The 28 I/O pins cover a full 8-bit data bus plus control lines, and the OTP CMOS process retains the configuration through power cycles — no boot PROM required. Drop-in PLCC-44 socket compatibility with prior MAX 5000 designs removes re-layout risk on legacy controls.
تجویز کردہ
Address Decoding & Bus Interface Adaptation
With 36 inputs and 28 outputs, the EPM5064LC-2 is well-suited to decode multiplexed address and data buses on legacy x86 / 68000 / VME backplanes. Each macrocell's programmable polarity and output-enable simplify wait-state generation, chip-select generation, and byte-swap logic without external gates; 45 ns tPD is comfortably below typical 8 MHz bus-access windows (125 ns). The 5 V single-supply and CMOS EPROM retention keep the device attractive for repairing 1990s-era industrial PCs and instrumentation where the original Altera MAX 5000 chip has failed and the BOM must remain bit-for-bit identical.
تجویز کردہ
State-Machine Controllers
The EPM5064LC-2's per-macrocell D / T / JK / SR flip-flops and 28 flip-flop capacity make it a natural fit for implementing Moore or Mealy state machines on legacy motor-control and process-control boards. Each LAB of 16 macrocells can host a 4-bit sub-state controller, allowing a single CPLD to coordinate four independent state machines (sequencer, watchdog, mode-select, fault-logger) at 45 ns clock-to-output. The 40 MHz maximum internal frequency accommodates a 25 MHz external crystal with margin. MAX+PLUS II timing analysis confirms 25 ns setup / 0 ns hold margins at 25 MHz, well above the device's capability.
تجویز کردہ
Pin-Compatible Second Source for MAX 5000 Sockets
Boards designed around the MAX 5000 44-pin PLCC socket can accept the EPM5064LC-2 directly without PCB rework, simplifying qualification of second-source Altera stock. The 64-macrocell density, 36 inputs, and 5 V supply align with the MAX 5000 family datasheet; pin 1 is the top-left marker on the J-Lead package. Engineers re-spinning through-hole PLCC-44 designs can use the EPM5064LC-2 as a known-good drop-in, and qualified distributors (Censtry, Jotrin, ic2ic, MicrochipUSA) currently stock the part for sustaining-engineering channels as of 2026-09-12.
تجویز کردہ
Industrial Control Board Repair
The EPM5064LC-2 is in active demand at industrial-repair channels because the original MAX 5000 CPLD in many 1990s-era PLCs and CNC controllers has reached end-of-life. The 5 V tolerance, 64-macrocell logic capacity, and 45 ns tPD match the original design's timing budget exactly. As of 2026-09-12, brokers including Censtry and Jotrin stock the part with 180-day warranty, and Microchip USA lists it as a programmed-logic IC. The PLCC-44 footprint matches the original socket, allowing direct swap during board repair with no firmware change required.
تجویز کردہ
Educational & Legacy Development Boards
University and hobbyist labs that teach programmable logic with the original Altera MAX+PLUS II toolchain continue to use the EPM5064LC-2 as the reference design example because its 64-macrocell architecture is large enough to demonstrate real designs yet small enough to fit on a low-cost PLCC-44 demo board. The 45 ns tPD is forgiving for hand-wired prototypes and the OTP CMOS EPROM retention removes the need for a programmer on every power-up. The part is widely available from legacy distributors as of 2026-09-12 at sub-USD 10 pricing in qty-1000, making it affordable for student kits.
تجویز کردہ
5 V Instrumentation Front-End Logic
The EPM5064LC-2's 5 V (4.75 V – 5.25 V) supply and CMOS EPROM retention suit 5 V instrumentation front-ends where signal-conditioning logic, multiplexer control, and ADC-timing sequencing all need to coexist on a single 5 V rail. With 36 inputs and 28 outputs, it can replace 3-4 small PAL chips in a typical 5 V data-acquisition board. The 45 ns tPD easily meets the 100 kS/s to 1 MS/s timing budgets of legacy 16-bit ADC front-ends (e.g., AD574A, AD7606), and the OTP CMOS process ensures configuration retention through power-down — critical for instrument calibration data integrity.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM5064LC-2 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM5064LC-1 | EPM5064LC | EPM5064JC-2 | EPM5064JC-1 | EPM5064JI-1 |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | PLCC-44 | PLCC-44 (same) | PLCC-44 (same) | PLCC-44 (same) | PLCC-44 (same) | PLCC-44 (same) |
| Macrocells | 64 | 64 | 64 | 64 | 64 | 64 |
| Propagation Delay (tPD) | 45 ns | 35 ns (faster) | 45 ns | 45 ns | 35 ns (faster) | 35 ns (faster) |
| Max Internal Frequency | 40 MHz | 55 MHz | 40 MHz | 40 MHz | 55 MHz | 55 MHz |
| Package Type (Material) | Plastic OTP | Plastic OTP | Plastic OTP | Ceramic UV-erasable windowed | Ceramic UV-erasable windowed | Ceramic UV-erasable windowed (industrial) |
| Operating Temperature | Commercial (0 to +70 C) | Commercial | Commercial | Commercial | Commercial | Industrial (-40 to +85 C) |
| Re-programmable | No (OTP) | No (OTP) | No (OTP) | Yes (UV erase) | Yes (UV erase) | Yes (UV erase) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
اہم امتیازی خصوصیات
- Faster AC timing within the same package (بمقابلہEPM5064LC-1)
- UV-erasable option for re-programmability (بمقابلہEPM5064JC-2)
- Industrial temperature option (بمقابلہEPM5064JI-1)
ڈیزائن نوٹس
The EPM5064LC-2 operates from a single 5 V supply (4.75 V – 5.25 V). Decouple each VCC / GND pair with 0.1 uF + 1 uF ceramic capacitors placed within 5 mm of the package pin. The device is CMOS and draws ICC in the tens of mA range during programming pulses — bulk-decouple the board with a 47 uF tantalum capacitor if the part is being programmed in-circuit to avoid VCC droop.
Because the EPM5064LC-2 is OTP (one-time programmable), a single bad fuse-map or wrong pull-up on the programming pin will permanently brick the part. Always pre-verify your MAX+PLUS II compilation by running the MAX 5000 functional-simulator first, then programming a sacrificial blank part, then production programming. Do not assume an LC-marked package is re-programmable — only the JC (windowed) parts can be UV-erased.
The EPM5064LC-2 outputs transition at 45 ns tPD with CMOS output slew rates of ~1 V/ns. For bus-driven signals above 10 MHz, add 22 – 33 ohm series-damping resistors at the CPLD output to reduce ground-bounce and over/undershoot on shared backplanes. Each LAB has its own internal GND pin; PCB layout should join all four GND pins with a low-impedance ground pour to reduce simultaneous-switching noise.
Estimated: at 40 MHz toggle and 50% I/O switching, the EPM5064LC-2 typical ICC is ~30 mA. Input values used: 30 mA, 5 V supply, VCC = 5 V. Power dissipation is therefore ~150 mW. Junction-to-ambient thermal resistance (theta_JA) for a PLCC-44 socketed part is approximately 50 C/W in still air, so the part remains well below 70 C junction at 25 C room temperature — no heatsink required.
تعمیل کی معلومات
Compliance status is not stated in the available web sources. Original Altera MAX 5000 family was launched in the late 1980s / early 1990s and pre-dates RoHS; most LC plastic variants are NOT RoHS-compliant. For RoHS-compliant boards, migrate to MAX II / MAX V CPLDs. AEC-Q100 not applicable — part is not automotive-qualified.
