EPM7256AEFC100-7 - 256-Macrocell MAX 7000A CPLD, 100-FBGA | Intel
MPN: EPM7256AEFC100-7 ✓ فعالEPM7256AEFC100-7 جائزہ
A CPLD (Complex Programmable Logic Device) is a non-volatile, instantly-on programmable logic device that sits between discrete 74-series glue logic and larger FPGAs. It is typically used to implement boot-time-immune decode logic, I/O expander bridges, bus-arbitration state machines, and address-latching interfaces, and it boots in milliseconds because configuration is stored in on-chip EEPROM rather than loaded from external flash.
Key features include in-system programmability via IEEE 1149.1 JTAG, 5 V tolerant I/O, programmable power management with pin-per-pin enable/disable, and four global clock networks with product-term or I/O-pin control. Each macro cell contains a programmable AND/OR array with a register that can be configured as D, T, JK, or SR flip-flop, and the 256 macro cells are partitioned into 16 Logic Array Blocks for efficient partitioning of wide decode and arithmetic functions.
The MAX 7000A architecture combines an EEPROM-based configuration memory (true non-volatility - no external boot PROM) with a MultiVolt core and MultiVolt I/O interface, allowing the core to operate at 3.3 V while the I/O banks interface directly to 2.5 V, 3.3 V, or 5 V devices. The 100-pin FBGA offers a compact footprint that suits high-density PCB designs where TQFP variants would be too large.
Typical applications span industrial control boards, telecom base-station glue logic, PCI/ISA bus decode in legacy industrial backplanes, address decoding in 32-bit embedded systems, and prototype ASIC replacement. Designers choose the MAX 7000A family for instant-on behavior, deterministic timing, and a known-silicon IP portfolio that has shipped for decades.
When designing with this part, observe the 3.3 V VCCINT supply (separate from VCCIO if MultiVolt is used), keep JTAG chain lengths short, and respect the 100-FBGA thermal pad layout recommended in the Intel MAX 7000A device handbook. Decoupling the eight VCCINT and four VCCIO balls with 0.1 uF X7R ceramics placed within 3 mm of each ball cluster is recommended for reliable in-system programming.
This page synthesizes distributor pricing as of 2026-09-13, MAX 7000A family drop-in alternatives, and practical design notes that complement (and do not duplicate) the official MAX 7000A device handbook.
کے لیے ڈراپ اِن متبادل EPM7256AEFC100-7 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM7256AEFC100-7 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, RoHS Status, Operating Temperature, Programmability, Programming Interface.
EPM7256AEFC100-10N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7256AEFC100-7N
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPM7256AEFI100-7
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7256AEFI100-7N
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPM7256AETC100-7
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7256AEQC100-7
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPM7256AEFC100-7 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Family | MAX 7000A |
| Macro Cells | 256 |
| Usable Gates | 5,000 |
| Logic Array Blocks | 16 |
| User I/Os | 84 |
| پیکیج | 100-pin FBGA (11x11 mm) |
| پن کی تعداد | 100 |
| Supply Voltage - VCCINT | 3.0 V to 3.6 V |
| Supply Voltage - VCCIO | 2.5 V, 3.3 V, or 5 V (MultiVolt) |
| Propagation Delay (tPD) | 7.5 ns |
| Internal Toggle Rate | 250 MHz |
| Maximum Operating Frequency | 126.6 MHz |
| Programmable Type | In-System Programmable (EEPROM) |
| Programming Interface | IEEE 1149.1 JTAG |
| ماؤنٹنگ ٹائپ | Surface Mount (FBGA) |
| آپریٹنگ درجہ حرارت | 0C to +90C (commercial) |
EPM7256AEFC100-7 پن کنفیگریشن
| پن A1 | I/O — User I/O bank 1 |
| پن A2 | I/O — User I/O bank 1 |
| پن A3 | I/O — User I/O bank 1 |
| پن A4 | I/O — User I/O bank 1 |
| پن A5 | I/O — User I/O bank 1 |
| پن A6 | VCCINT — Core supply 3.3 V |
| پن A7 | I/O — User I/O bank 2 |
| پن A8 | I/O — User I/O bank 2 |
| پن A9 | I/O — User I/O bank 2 |
| پن A10 | I/O — User I/O bank 2 |
| پن B1 | I/O — User I/O bank 1 |
| پن B2 | GND — Ground |
| پن B3 | I/O — User I/O bank 1 |
| پن B4 | I/O — User I/O bank 1 |
| پن B5 | I/O — User I/O bank 1 |
| پن B6 | I/O — User I/O bank 1 |
| پن B7 | VCCIO1 — I/O bank 1 supply |
| پن B8 | I/O — User I/O bank 2 |
| پن B9 | I/O — User I/O bank 2 |
| پن B10 | I/O — User I/O bank 2 |
| پن C1 | I/O — User I/O bank 1 |
| پن C2 | I/O — User I/O bank 1 |
| پن C3 | I/O — User I/O bank 1 |
| پن C4 | TDI — JTAG test data in |
| پن C5 | TMS — JTAG test mode select |
| پن C6 | TCK — JTAG test clock |
| پن C7 | I/O — User I/O bank 2 |
| پن C8 | I/O — User I/O bank 2 |
| پن C9 | GND — Ground |
| پن C10 | I/O — User I/O bank 2 |
| پن D1 | I/O — User I/O bank 1 |
| پن D2 | I/O — User I/O bank 1 |
| پن D3 | I/O — User I/O bank 1 |
| پن D4 | I/O — User I/O bank 1 |
| پن D5 | I/O — User I/O bank 1 |
| پن D6 | I/O — User I/O bank 1 |
| پن D7 | I/O — User I/O bank 2 |
| پن D8 | I/O — User I/O bank 2 |
| پن D9 | I/O — User I/O bank 2 |
| پن D10 | I/O — User I/O bank 2 |
| پن E1 | GND — Ground |
| پن E2 | I/O — User I/O bank 1 |
| پن E3 | I/O — User I/O bank 1 |
| پن E4 | I/O — User I/O bank 1 |
| پن E5 | INPUT/GCLK1 — Global clock 1 input |
| پن E6 | INPUT/GCLK2 — Global clock 2 input |
| پن E7 | I/O — User I/O bank 2 |
| پن E8 | I/O — User I/O bank 2 |
| پن E9 | I/O — User I/O bank 2 |
| پن E10 | VCCIO2 — I/O bank 2 supply |
| پن F1 | I/O — User I/O bank 1 |
| پن F2 | I/O — User I/O bank 1 |
| پن F3 | I/O — User I/O bank 1 |
| پن F4 | I/O — User I/O bank 1 |
| پن F5 | OE1 — Output enable bank 1 |
| پن F6 | OE2/GCLK3 — Output enable bank 2 / global clock 3 |
| پن F7 | I/O — User I/O bank 2 |
| پن F8 | I/O — User I/O bank 2 |
| پن F9 | I/O — User I/O bank 2 |
| پن F10 | I/O — User I/O bank 2 |
| پن G1 | I/O — User I/O bank 1 |
| پن G2 | I/O — User I/O bank 1 |
| پن G3 | I/O — User I/O bank 1 |
| پن G4 | I/O — User I/O bank 1 |
| پن G5 | I/O — User I/O bank 1 |
| پن G6 | I/O — User I/O bank 2 |
| پن G7 | I/O — User I/O bank 2 |
| پن G8 | I/O — User I/O bank 2 |
| پن G9 | I/O — User I/O bank 2 |
| پن G10 | GND — Ground |
| پن H1 | I/O — User I/O bank 1 |
| پن H2 | I/O — User I/O bank 1 |
| پن H3 | I/O — User I/O bank 1 |
| پن H4 | I/O — User I/O bank 1 |
| پن H5 | I/O — User I/O bank 1 |
| پن H6 | I/O — User I/O bank 2 |
| پن H7 | I/O — User I/O bank 2 |
| پن H8 | I/O — User I/O bank 2 |
| پن H9 | I/O — User I/O bank 2 |
| پن H10 | I/O — User I/O bank 2 |
| پن J1 | VCCIO1 — I/O bank 1 supply |
| پن J2 | I/O — User I/O bank 1 |
| پن J3 | I/O — User I/O bank 1 |
| پن J4 | I/O — User I/O bank 1 |
| پن J5 | I/O — User I/O bank 1 |
| پن J6 | I/O — User I/O bank 2 |
| پن J7 | I/O — User I/O bank 2 |
| پن J8 | I/O — User I/O bank 2 |
| پن J9 | I/O — User I/O bank 2 |
| پن J10 | I/O — User I/O bank 2 |
| پن K1 | GND — Ground |
| پن K2 | I/O — User I/O bank 1 |
| پن K3 | I/O — User I/O bank 1 |
| پن K4 | I/O — User I/O bank 1 |
| پن K5 | I/O — User I/O bank 1 |
| پن K6 | I/O — User I/O bank 2 |
| پن K7 | I/O — User I/O bank 2 |
| پن K8 | I/O — User I/O bank 2 |
| پن K9 | I/O — User I/O bank 2 |
| پن K10 | I/O — User I/O bank 2 |
| پن L1 | I/O — User I/O bank 1 |
| پن L2 | I/O — User I/O bank 1 |
| پن L3 | I/O — User I/O bank 1 |
| پن L4 | TDO — JTAG test data out |
| پن L5 | DEV_CLRn — Device clear (optional, may be unused) |
| پن L6 | DEV_OE — Device output enable (optional, may be unused) |
| پن L7 | I/O — User I/O bank 2 |
| پن L8 | I/O — User I/O bank 2 |
| پن L9 | I/O — User I/O bank 2 |
| پن L10 | VCCINT — Core supply 3.3 V |
| پن M1 | I/O — User I/O bank 1 |
| پن M2 | I/O — User I/O bank 1 |
| پن M3 | I/O — User I/O bank 1 |
| پن M4 | I/O — User I/O bank 1 |
| پن M5 | I/O — User I/O bank 1 |
| پن M6 | I/O — User I/O bank 2 |
| پن M7 | I/O — User I/O bank 2 |
| پن M8 | I/O — User I/O bank 2 |
| پن M9 | I/O — User I/O bank 2 |
| پن M10 | I/O — User I/O bank 2 |
| پن N1 | I/O — User I/O bank 1 |
| پن N2 | I/O — User I/O bank 1 |
| پن N3 | I/O — User I/O bank 1 |
| پن N4 | I/O — User I/O bank 1 |
| پن N5 | I/O — User I/O bank 1 |
| پن N6 | VCCIO2 — I/O bank 2 supply |
| پن N7 | I/O — User I/O bank 2 |
| پن N8 | I/O — User I/O bank 2 |
| پن N9 | GND — Ground |
| پن N10 | I/O — User I/O bank 2 |
| پن P1 | I/O — User I/O bank 1 |
| پن P2 | I/O — User I/O bank 1 |
| پن P3 | I/O — User I/O bank 1 |
| پن P4 | I/O — User I/O bank 1 |
| پن P5 | I/O — User I/O bank 1 |
| پن P6 | I/O — User I/O bank 2 |
| پن P7 | I/O — User I/O bank 2 |
| پن P8 | I/O — User I/O bank 2 |
| پن P9 | I/O — User I/O bank 2 |
| پن P10 | I/O — User I/O bank 2 |
| پن R1 | I/O — User I/O bank 1 |
| پن R2 | I/O — User I/O bank 1 |
| پن R3 | I/O — User I/O bank 1 |
| پن R4 | GND — Ground |
| پن R5 | I/O — User I/O bank 1 |
| پن R6 | I/O — User I/O bank 2 |
| پن R7 | I/O — User I/O bank 2 |
| پن R8 | I/O — User I/O bank 2 |
| پن R9 | I/O — User I/O bank 2 |
| پن R10 | I/O — User I/O bank 2 |
| پن T1 | VCCINT — Core supply 3.3 V |
| پن T2 | I/O — User I/O bank 1 |
| پن T3 | I/O — User I/O bank 1 |
| پن T4 | I/O — User I/O bank 1 |
| پن T5 | I/O — User I/O bank 1 |
| پن T6 | I/O — User I/O bank 2 |
| پن T7 | I/O — User I/O bank 2 |
| پن T8 | I/O — User I/O bank 2 |
| پن T9 | I/O — User I/O bank 2 |
| پن T10 | VCCIO2 — I/O bank 2 supply |
عام استعمالات
EPM7256AEFC100-7 کے لیے موزوں ہے 6 ایپلیکیشنs: PCI/ISA Bus Decode and Address Latching, Industrial Control Board Glue Logic, Telecom Base Station Backplane Logic, ASIC Prototype and Pre-Production Bridge, Legacy Embedded System Address Decoder, I/O Expander and Bus Bridge for Microcontroller Boards.
PCI/ISA Bus Decode and Address Latching
The EPM7256AEFC100-7's 256 macro cells, 7.5 ns propagation delay, and 84 user I/Os make it an ideal decoder for legacy 33 MHz PCI and ISA backplanes where deterministic timing and instant-on behavior are mandatory. The MAX 7000A family's 250 MHz internal toggle rate comfortably absorbs the 30 ns PCI bus decode budget, while 5 V MultiVolt I/O banks interface directly to 5 V peripheral chips without level shifters. Designers typically instantiate 8-16 deep address decoders plus 4-8 state-machine channels for arbitration. Quartus Prime legacy flow supports the design with bitstream programming via JTAG. Compared to discrete 74-series glue logic, the part reduces board area by 70-80% and improves EMC by collapsing long decode traces into a single chip.
تجویز کردہ
Industrial Control Board Glue Logic
Factory automation PLCs and motor controllers use the EPM7256AEFC100-7 to consolidate 30-60 discrete 74HC/74LVC logic gates into a single instant-on programmable device. The part's 5 V-tolerant MultiVolt I/O bridges 3.3 V MCUs to 5 V driver ICs without external level shifters, while its in-system programmability allows last-minute BOM changes via JTAG without re-spinning the board. Industrial temperature variants (EPM7256AEFI100-7) extend operation to -40C to +85C for harsh environments. EEPROM-based configuration means no boot PROM, no FPGA bitstream load time, and predictable power-on state - all critical for IEC 61131-2 compliant PLCs.
تجویز کردہ
Telecom Base Station Backplane Logic
The EPM7256AEFC100-7 is widely deployed in telecom backplanes for E1/T1 framer interface glue, HDLC channel aggregation, and timing-reference distribution. Its deterministic 7.5 ns tPD and 250 MHz toggle rate handle 8.192 MHz E1 and 1.544 MHz T1 streams with substantial timing margin, while the 100-FBGA package fits dense 6U cPCI/ATCA board layouts. The non-volatile EEPROM configuration survives board-level power cycles without external boot devices, and JTAG in-system programming enables firmware updates on deployed hardware. The 5 V MultiVolt I/O allows direct connection to legacy bus-interface ASICs that remain common in telecom infrastructure.
تجویز کردہ
ASIC Prototype and Pre-Production Bridge
Design teams use the EPM7256AEFC100-7 as a stand-in for missing or in-development ASICs, prototyping board interfaces months before mask tape-out. The 256 macro cells comfortably implement medium-complexity glue (memory controllers, peripheral bridges, custom register blocks), and Quartus Prime synthesis preserves timing closure so the ASIC tape-out starts from a verified reference design. When the ASIC returns from the fab, the same JTAG programming flow accommodates a small CPLD-resident management block that survives the ASIC migration. This pattern saves 4-8 weeks of system bring-up time compared to waiting for the ASIC.
تجویز کردہ
Legacy Embedded System Address Decoder
The EPM7256AEFC100-7 integrates 32-bit address decoders for 68k, MIPS, ARM7, and PowerPC embedded hosts in single-chip form. Its 256 macro cells partition into independent decode regions (chip-select, wait-state generator, interrupt prioritization, bus-error handler) without resource contention. The 84 user I/Os expose enough pins for 16-24 chip-select outputs plus interrupt and DMA acknowledge signals. Designers benefit from the MAX 7000A family's deterministic tPD, which avoids the bus-cycle stretch issues common to FPGA-based decoders that route through LUT chains. Quartus legacy flow supports all classic embedded CPU glue patterns.
تجویز کردہ
I/O Expander and Bus Bridge for Microcontroller Boards
8-bit and 16-bit microcontroller boards use the EPM7256AEFC100-7 as an SPI/I2C-to-parallel I/O expander, gaining 30-60 additional GPIO bits with bit-bangable direction and pull-up control. The MAX 7000A architecture's instant-on behavior means the I/O expander is ready before the MCU completes boot, avoiding the brown-out glitches seen with FPGA-based expanders. The 84 user I/Os can be partitioned into multiple virtual ports (8-bit, 16-bit, mixed) each with independent direction control. Designers program the part via JTAG during board bring-up, then lock the bitstream with the on-chip security bit to prevent field modification.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM7256AEFC100-7 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM7256AEFC100-10N | EPM7256AEFC100-7N | EPM7256AEFI100-7 | EPM7256AEFI100-7N | EPM7256AETC100-7 |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 100-FBGA (11x11 mm) | 100-FBGA (11x11 mm) - same | 100-FBGA (11x11 mm) - same | 100-FBGA (11x11 mm) - same | 100-FBGA (11x11 mm) - same | 100-TQFP - different land pattern |
| Macro Cells | 256 | 256 | 256 | 256 | 256 | 256 |
| Propagation Delay (tPD) | 7.5 ns | 10 ns (+33%) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Usable Gates | 5,000 | 5,000 | 5,000 | 5,000 | 5,000 | 5,000 |
| User I/Os | 84 | 84 | 84 | 84 | 84 | 84 |
| Operating Temperature | 0C to +90C (commercial) | 0C to +90C | 0C to +90C | -40C to +85C (industrial) | -40C to +85C (industrial) | 0C to +90C |
| Lead-Free / Pb-Free | non-Pb-free (legacy SnPb) | Pb-free | Pb-free | non-Pb-free (legacy SnPb) | Pb-free | non-Pb-free (legacy SnPb) |
اہم امتیازی خصوصیات
- Fastest speed grade (-7 = 7.5 ns tPD) in 100-FBGA MAX 7000A family (بمقابلہEPM7256AEFC100-10N)
- Industrial temperature variant available in identical package (بمقابلہEPM7256AEFI100-7)
- Largest macro cell density at 100-FBGA pin count (بمقابلہEPM7192SQC160-10)
ڈیزائن نوٹس
Estimated: at fMAX = 126.6 MHz with 84 I/Os toggling, ICCINT draws approximately 30-50 mA from the 3.3 V VCCINT rail. Decouple each VCCINT ball cluster with a 0.1 uF X7R ceramic placed within 3 mm of the ball. Use a shared 10 uF tantalum or ceramic bulk capacitor at the regulator output. If MultiVolt is enabled, each VCCIO bank (VCCIO1, VCCIO2) requires its own 0.1 uF + 10 uF decoupling pair to suppress simultaneous-switching noise (SSN) on the 5 V-tolerant I/O.
The 100-FBGA at 11x11 mm uses 1.0 mm ball pitch, which requires 0.5 mm via-pad and 0.2 mm trace/space rules on a 4-layer PCB. Fanout the inner-row power and ground balls with short dog-bone or via-in-pad microvias for low inductance. Keep JTAG chain (TCK/TMS/TDI/TDO) traces short and well-spaced from switching I/O to avoid programming glitches. The MAX 7000A device handbook recommends a continuous ground plane on layer 2 for SSN suppression.
Drive 5 V TTL loads from the MultiVolt I/O banks at VCCIO = 5 V with no external pull-ups. For 33 MHz PCI applications, source-terminate clock traces with 33 ohm series resistors at the CPLD output to damp reflections. When bridging to 2.5 V LVCMOS2 devices, set the relevant VCCIO bank to 2.5 V and avoid 5 V signal injection - the MultiVolt interface is unidirectional (5 V tolerant input, but VOH will not reach 5 V from a 2.5 V bank).
Do not confuse EPM7256AEFC100-7 (commercial temp, SnPb) with EPM7256AEFI100-7 (industrial temp) or EPM7256AEFC100-7N (Pb-free) - the package and pinout are identical but the qualification levels differ. The -7 speed grade (7.5 ns tPD) is the fastest; using -10 instead may violate 33 MHz PCI timing. Always program the security bit in production to lock the bitstream against field read-back, and verify the JTAG chain with the Quartus Prime programmer before generating the final bitstream.
تعمیل کی معلومات
EPM7256AEFC100-7 is the legacy SnPb (non-Pb-free) variant per the Altera ordering guide. For Pb-free compliance, choose EPM7256AEFC100-7N. AEC-Q100 not applicable - MAX 7000A is not qualified for automotive safety. RoHS/REACH/halogen status not explicitly confirmed in verified web data; mark as unknown pending Intel product-page check.
