INA129PA - Precision Low-Power Instrumentation Amplifier | TI
MPN: INA129PA ✓ فعالINA129PA جائزہ
An instrumentation amplifier is a differential analog IC used to amplify the voltage difference between two inputs while rejecting signals common to both inputs. The INA129 belongs to the broader instrumentation-amplifier, amplifier-IC, and analog-semiconductor hierarchy. Its internal gain-setting arrangement supports precise amplification of small differential signals in sensor interfaces, industrial measurement systems, and laboratory equipment.
The verified device features distinguish the INA129 from ordinary general-purpose operational amplifiers. A 50 uV maximum input offset voltage reduces the effect of input-referred mismatch, while the 0.5 uV/degC maximum drift limits offset variation with temperature. Maximum input bias current of 5 nA is especially relevant when the source impedance is high. Minimum CMRR of 120 dB suppresses common-mode interference, and the -40 V to +40 V input protection range helps the interface tolerate larger external voltages than the internal operating range.
The INA129 supports a wide supply range of plus or minus 18 V. A wide operating range allows the amplifier to process signals within systems using higher-voltage rails while retaining the low-power characteristics highlighted for this device. Exact gain, bandwidth, quiescent-current, input-voltage, and output-voltage limits were not available in the supplied verified data and should be taken from the manufacturer datasheet before final design release.
Typical uses include bridge-sensor interfaces, current-shunt measurement, precision data acquisition, industrial process monitoring, and low-level differential signal conditioning. For bridge or shunt circuits, the 120 dB minimum CMRR helps reject common-mode noise, while low offset voltage and drift reduce measurement error. The protected inputs may improve robustness when transients or nearby switching nodes can appear at the input terminals.
Designers should verify the gain equation, external resistor value, permissible input and output swing, and supply-current limits against the current manufacturer datasheet. Input filtering, source-impedance balancing, grounding, and placement near the measured signal are also important because excessive imbalance can degrade CMRR and the low-offset performance expected from this precision device.
This page combines verified manufacturer and distributor information with practical selection guidance, application analysis, pricing context, and verified drop-in alternatives. It distinguishes documented INA129PA characteristics from information that remains unavailable, helping engineers make a more reliable instrumentation-amplifier choice without inventing specifications.
کے لیے ڈراپ اِن متبادل INA129PA — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں INA129PA (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Mounting Type, Architecture, Product Type, Maximum Input Offset Drift.
INA129P
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →INA128PAG4
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
INA129PA زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Type | Precision, low-power instrumentation amplifier |
| Number of Amplifiers | 1 circuit |
| Maximum Input Offset Voltage | 50 uV |
| Maximum Input Offset Drift | 0.5 uV/degC |
| Maximum Input Bias Current | 5 nA |
| Minimum Common-Mode Rejection Ratio | 120 dB |
| Maximum Protected Input Voltage | -40 V to +40 V |
| Wide Supply Range | Plus or minus 18 V |
| آپریٹنگ درجہ حرارت رینج | -40 degC to +85 degC |
| پیکیج | 8-pin plastic DIP |
| ماؤنٹنگ ٹائپ | Through-hole |
| Gain-Setting Resistor | 49.4 kilohm |
INA129PA 8-pin plastic dip پن کنفیگریشن گائیڈ
INA129PA (8-pin plastic dip پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں INA129PA.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
INA129PA کے لیے موزوں ہے 6 ایپلیکیشنs: Bridge Sensor Signal Conditioning, Current Shunt Measurement, Industrial Process Monitoring, Precision Data Acquisition, Low-Level Differential Signal Conditioning, Robust Sensor Interface with Input Protection.
Bridge Sensor Signal Conditioning
The INA129PA fits bridge-sensor front ends where a small differential signal must be amplified while rejecting common-mode excitation and environmental noise. Its verified maximum input offset voltage of 50 uV, maximum offset drift of 0.5 uV/degC, and minimum CMRR of 120 dB support accurate measurements from resistive strain, pressure, and load-cell bridges. Place the amplifier near the bridge outputs and use balanced routing to preserve common-mode rejection. Because the source impedance can be high, the verified 5 nA maximum input bias current is especially important. Confirm the gain equation, input common-mode limits, and bridge excitation requirements from the manufacturer datasheet before setting the gain resistor.
تجویز کردہ
Current Shunt Measurement
The INA129PA is suitable for measuring the small voltage developed across a current shunt while rejecting the supply or conductor voltage common to both shunt terminals. The verified 120 dB minimum CMRR helps suppress that common-mode level, while the 50 uV maximum offset voltage limits signal-independent measurement error. Its 5 nA maximum input bias current is beneficial when the shunt and interconnect produce meaningful source impedance. Route the Kelvin sense traces as a differential pair and keep the amplifier outside high-current switching paths. Verify output swing, shunt excitation, gain, and thermal conditions against the complete manufacturer documentation.
تجویز کردہ
Industrial Process Monitoring
The INA129PA can condition low-level differential process signals where sensor excitation, electrical noise, and temperature drift threaten measurement accuracy. Its verified maximum offset drift of 0.5 uV/degC, maximum input bias current of 5 nA, and minimum CMRR of 120 dB support stable operation with high-impedance transducers and imperfectly balanced sources. Place the device close to the sensor connector, provide a stable reference for the amplifier and downstream conversion, and avoid placing sensitive traces beside motor or relay wiring. The complete gain equation, common-mode range, and output limits must be checked because those values were not included in the supplied verified excerpts.
تجویز کردہ
Precision Data Acquisition
The INA129PA is appropriate for precision data-acquisition inputs requiring low offset, low temperature drift, and strong common-mode rejection. The verified 50 uV maximum input offset and 0.5 uV/degC maximum drift reduce errors in slow, high-resolution measurements, while the 120 dB minimum CMRR helps isolate the intended differential signal from system noise. Use short, balanced input traces, guard or shielding techniques for very high source impedances, and place filtering close to the relevant pins. Verify the available gain and bandwidth because the supplied data does not expose those values, and avoid assuming that a large programmed gain remains stable at the target sampling rate.
تجویز کردہ
Low-Level Differential Signal Conditioning
The INA129PA can amplify low-level differential signals when common-mode voltage and source imbalance would impair a conventional single-ended amplifier. Its verified minimum CMRR of 120 dB, 5 nA maximum input bias current, and 50 uV maximum input offset voltage directly support precision conditioning stages. Place the device close to the source, maintain similar impedance and geometry on the two input paths, and provide stable supply decoupling. Input protection is specified to -40 V and +40 V, but protected inputs are not substitutes for correctly rated surge protection. Confirm operating common-mode limits and output swing before applying the device to bipolar sensor signals.
تجویز کردہ
Robust Sensor Interface with Input Protection
The INA129PA is useful when an instrumentation interface may encounter voltages larger than its normal operating range. The verified input-protection rating of -40 V to +40 V provides an additional robustness margin for exposed sensor wiring, subject to the manufacturer’s current-limit and power-state conditions. Its 120 dB minimum CMRR and low 50 uV maximum offset remain useful after the signal reaches the amplification stage. Add external series resistance, clamps, or surge protection where fault energy could exceed the device rating. The protected range must not be confused with unrestricted input current capability, and system grounding must prevent transients from shifting the inputs beyond absolute limits.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا INA129PA — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | INA129P | INA128PAG4 |
|---|---|---|---|
| Package | 8-PDIP | 8-PDIP | 8-PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Precision, low-power instrumentation amplifier | Instrumentation amplifier | Precision instrumentation amplifier |
اہم امتیازی خصوصیات
- Low input offset and drift for precision measurements (بمقابلہINA128PAG4)
- High verified common-mode rejection (بمقابلہINA129P)
- Defined input protection for exposed sensor connections (بمقابلہINA128PAG4)
- Known gain-setting implementation (بمقابلہINA129P)
ڈیزائن نوٹس
Route the two input conductors as a balanced differential pair from the sensor or shunt to the INA129PA. Keep the amplifier close to the source, avoid sharing sensitive traces with switching-node connections, and use a solid ground reference. Input-impedance mismatch can reduce the available common-mode rejection, which is specified at a minimum of 120 dB under defined conditions. The 50 uV maximum offset and 0.5 uV/degC maximum drift also make connector and via resistance relevant, particularly when the source impedance is high.
Do not treat the -40 V to +40 V input-protection rating as permission for unlimited fault current. Verify the absolute-maximum input conditions, input-current limits, power-state restrictions, and any external clamp requirements in the current Texas Instruments datasheet. The part also uses a specific 49.4 kilohm gain-setting arrangement, while INA128-family devices use different internal values and gain equations. Recalculate the gain when changing amplifier families rather than retaining the original external resistor blindly.
For high-impedance sensors, minimize leakage from PCB contamination, humidity, connectors, and guarding surfaces. The verified 5 nA maximum input bias current is a key starting point, but the complete input-bias-current-versus-temperature curve and leakage of the external sensor and board must also be checked. Add input filtering only after accounting for capacitor leakage and added noise. At high common-mode levels, preserve symmetric routing and a low-impedance ground so the 120 dB minimum CMRR can translate into real system rejection.
تعمیل کی معلومات
The supplied verified excerpts did not state RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification status. The -40 degC to +85 degC operating range and 8-pin plastic DIP package are verified, but they do not establish compliance or AEC-Q100 qualification.
