PIC16C55T-10/SS - 8-Bit 10MHz OTP MCU 768B | Microchip
MPN: PIC16C55T-10/SS ✗ اختتامِ زندگیPIC16C55T-10/SS جائزہ
An 8-bit microcontroller is a single-chip computer that integrates a CPU, program memory, data RAM, I/O peripherals and often timers on a single die. The PIC16C5X family belongs to the broader category of microcontrollers (MCU), which themselves sit within the integrated circuit (IC) and embedded system taxonomy. 8-bit MCUs are widely used in cost-sensitive and deterministic control applications because they offer predictable instruction timing, low power consumption and a small footprint. Microchip's PIC architecture uses a RISC-style 12-bit instruction word with 33 single-word/single-cycle instructions, delivering roughly 2:1 code compression over competitive 8-bit MCUs.
Key features of the PIC16C55T-10/SS include 20 general-purpose digital I/O pins organized across multiple ports, a 4 MHz internal RC oscillator option, an external oscillator interface, an 8-bit timer/counter with a programmable prescaler, a watchdog timer for reliable operation, and a power-on reset circuit. The device operates from 2.5 V to 6.25 V across the industrial -40 C to +85 C temperature range and consumes very low operating current. The CMOS design provides fully static operation.
Architecturally, the PIC16C55T-10/SS uses a Harvard architecture with separate program and data buses, a 12-bit program word and an 8-bit data path. This separation allows instruction fetch and data access to occur in the same clock cycle, contributing to the family's characteristic 2:1 code compression and high throughput-per-MHz figure. The OTP program memory is programmed once and cannot be erased, which is appropriate for high-volume, cost-sensitive production.
Typical applications include consumer appliance control, automotive body electronics, industrial sensor interfaces, low-end remote controls, battery chargers, LED lighting controllers and small motor control subsystems. The 20 I/O pins easily accommodate button matrices, LED arrays, relay drivers and serial-bit-banged communication.
When designing with the PIC16C55T-10/SS, observe the 6.25 V absolute maximum VDD rating and place a 0.1 uF decoupling capacitor adjacent to the VDD pin. The OTP memory cannot be re-programmed, so production-grade code should be verified on a windowed (JW) variant or the PIC16C55 EPROM/ROM equivalent during development. The "/SS" SSOP package requires standard surface-mount reflow profiles per JEDEC J-STD-020.
کے لیے ڈراپ اِن متبادل PIC16C55T-10/SS — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16C55T-10/SS (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Program Memory Size, Program Memory Type, Core Architecture, RAM Size.
PIC16C55-10/SS
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC16C55-10I/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C55-LPI/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C55-HSI/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C55A-04E/SS
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F54-I/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C55T-10/SS زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | 8-bit PIC RISC |
| Family | PIC16C5X |
| زیادہ سے زیادہ کلاک فریکوئنسی | 10 MHz |
| Program Memory Size | 768 bytes (512 x 12) OTP |
| RAM Size | 25 bytes |
| Program Memory Type | OTP (One-Time Programmable) |
| Instruction Word Size | 12 bits |
| Number of I/O Pins | 20 |
| Supply Voltage (VDD) | 2.5 V to 6.25 V |
| آپریٹنگ درجہ حرارت | -40 C to +85 C (industrial) |
| پیکیج | 28-SSOP (5.30 mm body width) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| پنز کی تعداد | 28 |
| Timers | 1 x 8-bit with prescaler |
| Watchdog Timer | Yes (on-chip) |
| Oscillator Type | External RC/xtal, internal 4 MHz RC option |
| MSL لیول | 1 (unlimited) |
PIC16C55T-10/SS پن کنفیگریشن
| پن 1 | RA0 — Bidirectional I/O pin; can also be used as analog input on some 5X variants |
| پن 2 | RA1 — Bidirectional I/O pin |
| پن 3 | RA2 — Bidirectional I/O pin |
| پن 4 | RA3 — Bidirectional I/O pin |
| پن 5 | T0CKI — Timer 0 clock input; also general-purpose I/O |
| پن 6 | OSC1 — Oscillator input; connect to crystal/ceramic resonator or external clock |
| پن 7 | OSC2 — Oscillator output; connects to crystal when used in crystal mode |
| پن 8 | RB0 — Bidirectional I/O pin |
| پن 9 | RB1 — Bidirectional I/O pin |
| پن 10 | RB2 — Bidirectional I/O pin |
| پن 11 | RB3 — Bidirectional I/O pin |
| پن 12 | RB4 — Bidirectional I/O pin |
| پن 13 | RB5 — Bidirectional I/O pin |
| پن 14 | RB6 — Bidirectional I/O pin |
| پن 15 | RB7 — Bidirectional I/O pin |
| پن 16 | VDD — Positive supply voltage (2.5 V to 6.25 V) |
| پن 17 | VSS — Ground reference |
| پن 18 | RC0 — Bidirectional I/O pin |
| پن 19 | RC1 — Bidirectional I/O pin |
| پن 20 | RC2 — Bidirectional I/O pin |
| پن 21 | RC3 — Bidirectional I/O pin |
| پن 22 | RC4 — Bidirectional I/O pin |
| پن 23 | RC5 — Bidirectional I/O pin |
| پن 24 | RC6 — Bidirectional I/O pin |
| پن 25 | RC7 — Bidirectional I/O pin |
| پن 26 | VSS — Ground reference (secondary) |
| پن 27 | VDD — Positive supply voltage (secondary) |
| پن 28 | MCLR — Master Clear reset input (active low); tie to VDD through pull-up for normal operation |
عام استعمالات
PIC16C55T-10/SS کے لیے موزوں ہے 6 ایپلیکیشنs: Consumer Appliance Control, Automotive Body Electronics, Remote Control and IR Transmitter, LED Lighting Controllers, Industrial Sensor Interface Modules, Battery Chargers and Small Power Tools.
Consumer Appliance Control
The PIC16C55T-10/SS is well suited to consumer appliance control boards including washing-machine user interfaces, microwave oven keypads, and small kitchen-appliance control panels. The 20 GPIO pins directly drive 7-segment LED displays, button-matrix keypads, and relay coils without external logic, while the 10 MHz core comfortably handles debouncing, mode-state machines, and timer-based sequencing in real time. The 768-byte OTP program memory is sufficient for fixed-function appliance logic where code is finalized at production, and the 2.5-6.25 V VDD range matches the 5 V rails common in white goods. The 28-SSOP package keeps the board footprint small and reflow-compatible.
تجویز کردہ
Automotive Body Electronics
Within automotive body electronics, the PIC16C55T-10/SS is used in simple control modules such as seat-position switches, mirror-fold actuators, interior lighting controllers, and HVAC mode selectors. The 8-bit RISC core delivers deterministic single-cycle instruction execution that simplifies timing analysis for safety-relevant functions, while the industrial -40 C to +85 C temperature range tolerates under-dash and cabin environments. The 20 GPIO pins can directly drive low-side FETs or relays, and the on-chip watchdog timer provides autonomous fault recovery required for in-vehicle reliability. The 28-SSOP surface-mount package withstands standard automotive reflow profiles.
تجویز کردہ
Remote Control and IR Transmitter
The PIC16C55T-10/SS is widely deployed in handheld IR remote controls for TVs, set-top boxes, audio equipment, and ceiling fans. The 8-bit core easily implements RC-5, NEC, and SIRC IR protocols via bit-banged GPIO at 38 kHz carrier frequency, while the 8-bit timer with prescaler produces accurate carrier waveforms. Low-power CMOS design extends battery life, and 20 I/O pins support keypads up to 4x5 plus LED indicators. The 768-byte OTP program memory holds the entire transmission protocol stack plus device codes. The 28-SSOP package is thin enough for compact remote enclosures.
تجویز کردہ
LED Lighting Controllers
In LED lighting controllers, the PIC16C55T-10/SS drives small RGB or single-channel LED fixtures with on/off, dimming, and color-cycle modes. The 20 GPIO pins connect directly to high-brightness LED driver ICs via PWM or logic-level enable, while the 8-bit timer generates PWM dimming signals at audio-noise-free frequencies. The wide 2.5-6.25 V VDD range lets the same MCU run on 3.3 V or 5 V supplies used in different lighting topologies. The 28-SSOP package reflows cleanly on FR-4 substrates and tolerates the warm-white LED ambient inside enclosed luminaires.
تجویز کردہ
Industrial Sensor Interface Modules
The PIC16C55T-10/SS works as a low-cost front-end in industrial sensor interface modules for digital temperature probes, optical counters, limit switches, and proximity sensors. The 20 GPIO pins handle digital I/O, frequency counters from the timer input, and basic sensor multiplexing, while the 10 MHz core performs linearization, threshold comparison, and alarm logic in real time. The on-chip watchdog timer is critical for unattended industrial installations where the MCU must recover from ESD or EMI events. The -40 C to +85 C industrial temperature range supports factory-floor and outdoor cabinets.
تجویز کردہ
Battery Chargers and Small Power Tools
The PIC16C55T-10/SS is used in single-cell and multi-cell NiMH/Li-ion charger controllers as well as budget cordless screwdrivers, garden tools, and small appliances. The 20 GPIO pins monitor battery voltage dividers, temperature thermistors, charge-status LEDs, and control MOSFET gate drivers, while the 8-bit timer produces PWM charge profiles. The 2.5-6.25 V VDD range is well matched to single-cell Li-ion (3.0-4.2 V) and 2-3 cell NiMH stacks. The 28-SSOP package fits the compact PCBs typical of these products and supports cost-sensitive high-volume production via the OTP program memory.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16C55T-10/SS — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16C55-10/SS | PIC16C55-10I/SS | PIC16C55-LPI/SS | PIC16C55-HSI/SS | PIC16C55A-04E/SS | PIC16F54-I/SS |
|---|---|---|---|---|---|---|---|
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max Clock Frequency | 10 MHz | 10 MHz | 10 MHz | 2 MHz (LP grade) | 20 MHz (HS grade) | 4 MHz | 20 MHz |
| Program Memory | 768B (512 x 12) OTP | 768B (512 x 12) OTP | 768B (512 x 12) OTP | 768B (512 x 12) OTP | 768B (512 x 12) OTP | 768B (512 x 12) OTP | 512x12 Flash |
| Program Memory Type | OTP | OTP | OTP | OTP | OTP | OTP | Flash (re-programmable) |
| RAM Size | 25 bytes | 25 bytes | 25 bytes | 25 bytes | 25 bytes | 25 bytes | 25 bytes |
| I/O Pins | 20 | 20 | 20 | 20 | 20 | 20 | 12 |
| Operating Voltage | 2.5 V to 6.25 V | 2.5 V to 6.25 V | 2.5 V to 6.25 V | 2.5 V to 6.25 V | 3.0 V to 6.25 V | 2.5 V to 6.25 V | 2.0 V to 5.5 V |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | NRND | Active |
اہم امتیازی خصوصیات
- 10 MHz industrial-grade speed in SSOP-28 (بمقابلہPIC16C55-LPI/SS)
- Tape & Reel factory packaging (بمقابلہPIC16C55-10/SS)
- Modern Flash-based equivalent available (بمقابلہPIC16F54-I/SS)
- 12-bit RISC core with 33 single-cycle instructions (بمقابلہPIC16C55A-04E/SS)
ڈیزائن نوٹس
Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VDD pin (pin 27) and a bulk capacitor (1-10 uF) on the same supply trace. The PIC16C55T-10/SS operates from 2.5 V to 6.25 V; voltages above 6.25 V can permanently damage the device. For battery-powered designs, use the internal 4 MHz RC oscillator and Sleep mode (if implemented via the A revision) to reduce quiescent current below 1 uA.
OTP program memory cannot be erased or re-programmed - a single programming error makes the device unusable. Plan for development on a windowed (JW-package) PIC16C55 or use the Flash-based PIC16F54 for prototyping. Also, the MCLR pin (pin 28) must be tied to VDD through a 10 kohm pull-up resistor; leaving MCLR floating causes intermittent resets. Do not confuse the PIC16C55 with the PIC16C55A - the latter adds Sleep mode and has slightly different oscillator behavior.
The 28-SSOP package has 0.65 mm pin pitch and 5.30 mm body width. Follow JEDEC J-STD-020 reflow profiles with a peak temperature not exceeding 260 C. Route the oscillator traces (OSC1/OSC2, pins 6-7) short and symmetric to minimize stray capacitance, and place the crystal/ceramic resonator within 5 mm of the MCU. Provide a guard ring around the oscillator area if digital switching signals are nearby to reduce EMI coupling.
Keep high-speed switching signals (PWM outputs, clock outputs) away from the OSC1/OSC2 traces and the MCLR reset line. The 20 GPIO pins can source/sink up to 25 mA per pin and 100 mA total per port; if driving higher-current loads like relays, use a MOSFET driver such as the Microchip TC4427 or a discrete low-side N-FET. Add a 0.1 uF bypass cap on each high-current GPIO-driven load supply pin to suppress inductive transients.
تعمیل کی معلومات
RoHS/REACH/lead-free/halogen-free status not explicitly confirmed in verified web data. AEC-Q100 not qualified (industrial-grade only). Conflict-minerals compliance assumed per Microchip corporate policy.
