PIC16C622T-04E/SS - 8-Bit 4MHz OTP MCU 3.5KB 20-SSOP | Microchip
MPN: PIC16C622T-04E/SS ✗ اختتامِ زندگیPIC16C622T-04E/SS جائزہ
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral interfaces into one package. Within the broader taxonomy of semiconductors, an MCU belongs to the digital logic / microcontroller class, and the PIC16C series occupies the mid-range 8-bit tier of Microchip's PIC portfolio, offering RISC architecture with a 14-bit instruction word optimized for compact, deterministic control code. OTP program memory allows the device to be programmed once during manufacturing, which lowers unit cost versus flash-based MCUs and is well suited to high-volume, fixed-function consumer and industrial products.
Key features of the PIC16C622T-04E/SS include the 14-bit instruction set, 35 single-word instructions (most single-cycle), a hardware multiplier, Brown-out Detect/Reset, Power-On Reset (POR), Watchdog Timer (WDT) with its own on-chip RC oscillator, an analog comparator, a programmable voltage reference, and a Capture/Compare/PWM (CCP) module. The wide 2.0V to 6.0V supply range allows battery-backed or 5V-rail designs, and the 20-SSOP outline saves board area versus a 20-pin PDIP alternative.
Architecturally, the PIC16C622 uses a Harvard bus with separate program and data paths and a 2-stage pipeline. On-chip peripherals include a 16-bit timer/counter (TMR1) optionally operable in sleep mode with an external crystal, an 8-bit timer/counter (TMR0) with 8-bit prescaler, and synchronous serial port (SSP) for SPI / I2C master-slave communication. Two analog comparators with a programmable reference voltage block add signal-conditioning capability without external op-amps.
Typical applications include white-goods and appliance controls, low-end remote controls, sensor signal conditioning with on-chip comparators, simple sensor-front-end nodes, battery chargers, automotive body controllers, lighting ballasts, and industrial control subsystems where cost dominates over reprogrammability. The extended temperature grade extends use to under-hood and outdoor enclosures.
When designing with this device, ensure that the chosen emulator/programmer (PICMASTER, MPLAB PM3, or PRO MATE II) supports the PIC16C62x OTP windowed/extended parts, and budget for a 25 mA / 6 V absolute maximum on VDD plus proper decoupling with 0.1 uF + 10 uF bulk capacitors. Pin-compatible PIC16C62x family members exist in the same 20-SSOP package, simplifying last-time buys and PCB reuse.
This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C6xx family, and practical design notes not found in the manufacturer datasheet alone.
کے لیے ڈراپ اِن متبادل PIC16C622T-04E/SS — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16C622T-04E/SS (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Program Memory Size, Operating Temperature Range, Program Memory Type, RoHS Status, Core Architecture.
PIC16C622T-04/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622-04E/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622-04/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622-20E/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622-20/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622T-04E/SO
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16C622T-04E/SS زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core | PIC 8-bit RISC |
| Series | PIC16C62x |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM Size | 128 x 8 bytes |
| EEPROM Size | None |
| زیادہ سے زیادہ کلاک فریکوئنسی | 4 MHz |
| Instruction Set Width | 14-bit |
| Number of I/O Pins | 13 |
| Supply Voltage Range | 2.0 V to 6.0 V |
| آپریٹنگ درجہ حرارت رینج | -40 C to +125 C (E grade, extended) |
| پیکیج | 20-SSOP (5.30 mm body width) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Oscillator Type | External |
| Peripherals | Brown-out Detect/Reset, POR, WDT, 2 Comparators, Programmable VREF, CCP, SSP (SPI/I2C) |
| Number of Timers | 2 (TMR0 8-bit, TMR1 16-bit) |
| RoHS اسٹیٹس | Non-compliant (contains lead in SSOP finish - verify variant) |
PIC16C622T-04E/SS پن کنفیگریشن
| پن 1 | RA2 — Bidirectional I/O port A bit 2; analog comparator 1 output |
| پن 2 | RA3 — Bidirectional I/O port A bit 3; analog comparator 1 inverting input |
| پن 3 | RA4 — Bidirectional I/O port A bit 4; T0CKI clock input |
| پن 4 | RA5 — Bidirectional I/O port A bit 5; analog comparator 2 inverting input |
| پن 5 | VSS — Ground reference |
| پن 6 | RB0 — Bidirectional I/O port B bit 0; external interrupt |
| پن 7 | RB1 — Bidirectional I/O port B bit 1 |
| پن 8 | RB2 — Bidirectional I/O port B bit 2 |
| پن 9 | RB3 — Bidirectional I/O port B bit 3 |
| پن 10 | RB4 — Bidirectional I/O port B bit 4; interrupt-on-change |
| پن 11 | RB5 — Bidirectional I/O port B bit 5; interrupt-on-change |
| پن 12 | RB6 — Bidirectional I/O port B bit 6; interrupt-on-change, ICSP clock |
| پن 13 | RB7 — Bidirectional I/O port B bit 7; interrupt-on-change, ICSP data |
| پن 14 | VSS — Ground reference |
| پن 15 | OSC1 — External oscillator input; crystal/resonator connection |
| پن 16 | OSC2 — External oscillator output; crystal/resonator connection |
| پن 17 | RA0 — Bidirectional I/O port A bit 0; analog comparator 2 output |
| پن 18 | RA1 — Bidirectional I/O port A bit 1; analog comparator 1 non-inverting input |
| پن 19 | MCLR — Master Clear reset input; active low |
| پن 20 | VDD — Positive supply voltage (2.0 V to 6.0 V) |
عام استعمالات
PIC16C622T-04E/SS کے لیے موزوں ہے 6 ایپلیکیشنs: White Goods and Appliance Control, Automotive Body Electronics, Industrial Sensor Front-Ends, Lighting Ballast and LED Driver Controllers, Remote Control and Consumer IR, Battery Chargers and Power Tools.
White Goods and Appliance Control
The PIC16C622T-04E/SS fits washing-machine, dishwasher, and refrigerator control boards because its 3.5 KB OTP holds a complete state-machine for motor sequencing, sensor polling, and user-interface handling while 128 bytes of RAM covers real-time variables. The two on-chip analog comparators accept 50/60 Hz zero-crossing signals for triac timing without external op-amps, saving both board space and BOM cost. Brown-out Reset and Power-On Reset protect the MCU during the brown-outs common in compressor-driven appliances. The -40 C to +125 C extended grade handles under-cabinet heat and motor-driver proximity.
تجویز کردہ
Automotive Body Electronics
Body controllers for seat adjusters, mirror modules, lighting clusters, and HVAC blend doors are dominated by 8-bit MCUs, and the PIC16C622T-04E/SS targets these directly through its -40 C to +125 C extended grade and 2.0-6.0 V supply, which tolerates cranking transients on the 12 V automotive bus when fed through a pre-regulator. The 13 GPIO lines drive relays, LED strings, and H-bridge enable pins directly. Hardware WDT with its own RC oscillator resets the controller when firmware locks up under EMI stress. Designers should confirm that PIC16C62x in 20-SSOP is qualified by the automaker's component acceptance procedure.
تجویز کردہ
Industrial Sensor Front-Ends
Sensor transmitters for pressure, level, flow, and temperature often need a microcontroller that can run 4-20 mA loop-powered or 24 V industrial-bus powered, condition analog signals, run a PID-style control loop, and drive an HART or MODBUS interface. The PIC16C622T-04E/SS's 13 GPIO, two analog comparators with programmable reference, and 16-bit TMR1 with capture register fit 4-20 mA loop-smart sensors where the OTP memory locks the calibration coefficients at programming. The wide 2.0-6.0 V supply allows the same MCU to be used across 3.3 V and 5 V sensor variants.
تجویز کردہ
Lighting Ballast and LED Driver Controllers
Fluorescent and HID ballasts use 8-bit MCUs to manage lamp warm-up, dimming, power-factor correction, and fault detection. The PIC16C622T-04E/SS runs the ballast state machine at 4 MHz with deterministic instruction timing, while its Capture/Compare/PWM module generates the lamp-drive switching waveform directly. The Brown-out Reset trips cleanly when the rectified mains drops below regulation. The 20-SSOP footprint simplifies high-density ballast PCB layouts where the controller sits next to the power MOSFETs. Extended temperature supports enclosed luminaire environments that exceed 70 C ambient.
تجویز کردہ
Remote Control and Consumer IR
Universal remote controls and simple IR transceivers need a low-cost, low-power MCU that runs a fixed IR protocol stack. The PIC16C622T-04E/SS's 3.5 KB OTP accommodates complete RC5/RC6 or NEC protocol decoders plus user-button matrix scanning on the 13 GPIO. The 16-bit TMR1 captures IR carrier edges accurately, while the SSP block talks to external EEPROM for learned-code storage. Sleep current is well under 1 uA with WDT running, supporting multi-year battery life on a coin cell.
تجویز کردہ
Battery Chargers and Power Tools
Cordless-drill and battery-charger controllers need an MCU that runs a charge algorithm (CC/CV for Li-ion, delta-V for NiMH, timer for SLA) and monitors pack thermistors. The PIC16C622T-04E/SS uses its on-chip analog comparators to detect end-of-charge voltage and temperature cutoffs without external op-amps. Brown-out Reset and the hardware WDT recover from inductive transients produced by brushed DC motors. The extended temperature range tolerates the elevated operating temperatures inside a charger housing that sits behind a high-current rectifier.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16C622T-04E/SS — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16C622T-04/SS | PIC16C622-04E/SS | PIC16C622-20E/SS | PIC16C622T-04E/SO |
|---|---|---|---|---|---|
| Package | 20-SSOP | 20-SSOP - same | 20-SSOP - same | 20-SSOP - same | 20-SOIC (different footprint) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 20 MHz | 4 MHz |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP |
| RAM Size | 128 x 8 bytes | 128 x 8 bytes | 128 x 8 bytes | 128 x 8 bytes | 128 x 8 bytes |
| Operating Temperature | -40 C to +125 C (E grade) | 0 C to +70 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Supply Voltage | 2.0 V to 6.0 V | 2.0 V to 6.0 V | 2.0 V to 6.0 V | 2.0 V to 6.0 V | 2.0 V to 6.0 V |
| Number of I/O | 13 | 13 | 13 | 13 | 13 |
اہم امتیازی خصوصیات
- Extended industrial temperature grade in a 20-SSOP (بمقابلہPIC16C622T-04/SS)
- Higher 20 MHz speed grade available pin-compatible (بمقابلہPIC16C622-20E/SS)
- On-chip dual comparators with programmable VREF (بمقابلہPIC16C620A family)
ڈیزائن نوٹس
The PIC16C622T-04E/SS uses One-Time Programmable (OTP) memory. Once a program is written, the device CANNOT be reprogrammed or code-erased, so a single bit error during development requires scrapping the part. Always build prototypes with PIC16C62x windowed (JW) or PIC16F62x flash parts and migrate to PIC16C622T-04E/SS only after firmware is fully validated. OTP also means field firmware updates are impossible - if your application needs field upgrades, choose PIC16F622 instead.
Place a 0.1 uF decoupling capacitor as close as possible between VDD (pin 20) and VSS (pin 14), with a 10 uF bulk tantalum or ceramic on the same rails. The PIC16C622 is sensitive to supply ripple during EEPROM/OTP programming and to ADC comparator noise during analog acquisition. Keep crystal traces short (<5 mm) and guard-pin the OSC1/OSC2 area with a ground ring to reduce EMI susceptibility from adjacent switching power stages.
The MCLR pin (pin 19) on PIC16C62x is active-low reset and MUST be pulled high through a 10 kohm resistor for normal operation. Do not leave it floating. If in-circuit serial programming (ICSP) is needed, the ICSP connector should sit on MCLR/RB6/RB7/VSS/VDD only and share no other MCU pins. RB6 and RB7 are used as ICSP clock/data and must remain unused in the application or be isolated from external drivers during programming.
The two on-chip analog comparators share their inputs with RA0-RA3 and are not multiplexed to dedicated ADC channels; their offset is +/- 5 mV typical and +/- 25 mV worst-case. For sub-25 mV threshold detection, calibrate the comparator reference in firmware or use an external op-amp. The programmable voltage reference block provides selectable reference steps between 0.31 V and VDD in 7 levels - choose the step that places the comparator threshold above the offset to avoid chatter.
تعمیل کی معلومات
PIC16C62x family predates RoHS adoption. SSOP finish is typically lead-based. AEC-Q100 qualification is not published for this commercial/industrial part; automotive designs should confirm acceptance at the OEM level.