PIC16F1518-I/SP - 8-bit 20MHz XLP MCU 28KB Flash 28-SPDIP | Microchip
MPN: PIC16F1518-I/SP ✓ فعالPIC16F1518-I/SP جائزہ
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a set of peripherals onto one die. The "8-bit" refers to the width of the data path and ALU; this device sits in the hierarchy: PIC16F1518 -> PIC16F151x family -> PIC16F1xx -> PIC® XLP 16F -> 8-bit MCU -> microcontroller -> embedded controller. XLP technology targets battery-powered and energy-harvesting designs where active current in the microamp range and sleep currents below 100 nA are required.
Key features include 25 high-current source/sink I/O (25 mA per pin), 17 channels of 10-bit ADC with selectable references, two 8-bit timers (TMR0/TMR2), one 16-bit timer (TMR1), two PWM modules, an enhanced power-on/off-reset, programmable ultra-low-power brown-out reset (ULPBOR), in-circuit serial programming (ICSP), and in-circuit debug. The 28-SPDIP package exposes 25 usable I/O plus VDD/VSS and provides robust through-hole soldering for development and industrial assemblies.
Typical applications span consumer appliances, handheld instruments, sensor nodes, white goods motor control, low-cost battery monitoring, and general-purpose logic replacement. The PIC16F1518 supersedes legacy PIC16F88/PIC16F877A designs that need 28 KB Flash and a true XLP sleep profile.
When designing, prefer the LF (PIC16LF1518) variant for sub-3 V operation; the standard F variant requires 2.3-5.5 V. Add a 100 nF decoupling cap on VDD, keep ADC traces short, and route MCLR with a 10 kohm pull-up. This page consolidates distributor stock, drop-in alternatives, and design notes not aggregated on any single manufacturer page.
کے لیے ڈراپ اِن متبادل PIC16F1518-I/SP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16F1518-I/SP (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Timers, Package, Mounting Type, ADC, Core Architecture.
PIC16F1519-I/SP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC16F1518-I/SS
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1517-I/SP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC16LF1518-I/SP
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1518-I/SP زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| CPU Architecture | 8-bit PIC RISC |
| Core Family | PIC® XLP™ 16F |
| Program Memory Type | Flash |
| Program Memory Size | 28 KB (16K x 14) |
| RAM Size | 1 KB |
| Maximum CPU Frequency | 20 MHz |
| Supply Voltage Range | 2.3 V to 5.5 V |
| آپریٹنگ درجہ حرارت رینج | -40C to +85C (Industrial) |
| Number of I/O Pins | 25 |
| I/O Sink/Source Current | 25 mA per pin |
| ADC Channels | 17 |
| ADC Resolution | 10-bit |
| Timers | 2x 8-bit (TMR0, TMR2), 1x 16-bit (TMR1) |
| PWM Channels | 2 |
| Package Type | 28-pin SPDIP (Skinny Plastic DIP) |
| Package Pitch | 2.54 mm (0.100 in) |
| ماؤنٹنگ ٹائپ | Through-Hole |
| MSL لیول | 1 (unlimited floor life at <30C / 85% RH) |
| RoHS اسٹیٹس | Compliant |
| ICSP / ICD | In-Circuit Serial Programming and In-Circuit Debug supported |
| Brown-Out Reset | Programmable Ultra-Low-Power BOR (ULPBOR) |
| Watchdog Timer | Enhanced WDT |
PIC16F1518-I/SP پن کنفیگریشن
| پن 1 | RA2/AN2 — Port A bit 2 / ADC input channel 2 |
| پن 2 | RA3/AN3/VREF+ — Port A bit 3 / ADC input 3 / positive voltage reference |
| پن 3 | RA4/AN4 — Port A bit 4 / ADC input channel 4 |
| پن 4 | RA5/AN5/SS — Port A bit 5 / ADC input 5 / SPI slave select |
| پن 5 | RA6/OSC2/CLKOUT — Port A bit 6 / crystal output / clock output |
| پن 6 | RA7/OSC1/CLKIN — Port A bit 7 / crystal input / clock input |
| پن 7 | VSS — Ground reference |
| پن 8 | RB0/AN12/INT — Port B bit 0 / ADC input 12 / external interrupt |
| پن 9 | RB1/AN10/C1IN+ — Port B bit 1 / ADC input 10 / comparator input |
| پن 10 | RB2/AN8 — Port B bit 2 / ADC input 8 |
| پن 11 | RB3/AN9/C1IN1- — Port B bit 3 / ADC input 9 / comparator input |
| پن 12 | RB4/AN11 — Port B bit 4 / ADC input 11 |
| پن 13 | RB5/AN13 — Port B bit 5 / ADC input 13 |
| پن 14 | RB6/ICSPCLK — Port B bit 6 / ICSP clock |
| پن 15 | RB7/ICSPDAT — Port B bit 7 / ICSP data |
| پن 16 | VSS — Ground reference (second VSS pin) |
| پن 17 | VDD — Positive supply voltage |
| پن 18 | MCLR/VPP/RE3 — Master clear / programming voltage / Port E bit 3 |
| پن 19 | RA0/AN0/ULPWU — Port A bit 0 / ADC input 0 / ultra-low-power wake-up |
| پن 20 | RA1/AN1 — Port A bit 1 / ADC input 1 |
| پن 21 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator output / clock input |
| پن 22 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator input / CCP2 PWM |
| پن 23 | RC2/P1A/CCP1 — Port C bit 2 / PWM output / CCP1 PWM |
| پن 24 | RC3/P1B — Port C bit 3 / enhanced PWM output |
| پن 25 | RC4 — Port C bit 4 (digital only) |
| پن 26 | RC5 — Port C bit 5 (digital only) |
| پن 27 | RC6 — Port C bit 6 (digital only) |
| پن 28 | RC7 — Port C bit 7 (digital only) |
عام استعمالات
PIC16F1518-I/SP کے لیے موزوں ہے 6 ایپلیکیشنs: Battery-Powered Sensor Nodes, White Goods Motor and PWM Control, Consumer Appliance User Interface, Handheld Test and Measurement Instruments, Industrial Process Sensor Conditioning, Automotive Interior Lighting and Switch Panels.
Battery-Powered Sensor Nodes
The PIC16F1518-I/SP fits battery-powered wireless sensor nodes thanks to its XLP active current in the microamp range and sleep current below 100 nA with ULPBOR enabled. Its 17-channel 10-bit ADC directly interfaces thermistors, photocells, and battery-divider rails without external signal conditioning. Compared to a discrete 555-timer-based sensor sampler, the PIC16F1518 reduces idle drain by orders of magnitude, extending CR2032 coin-cell life past two years at 1 sample/minute duty. The 25 high-current I/O also drive status indicators and low-side MOSFETs without buffering.
تجویز کردہ
White Goods Motor and PWM Control
Two PWM channels and three timers on the PIC16F1518-I/SP make it well suited for low-cost washing-machine pump, fan-speed, and small BLDC control boards. The 20 MHz core executes 5 MIPS, easily handling 8 kHz PWM with software dead-band insertion. The 25 mA sink/source I/O directly drives logic-level MOSFET gate drivers such as the MCP14E4 without external buffers. Designers benefit from the SPDIP-28 through-hole package for hand-reworkable prototypes.
تجویز کردہ
Consumer Appliance User Interface
The PIC16F1518-I/SP suits appliance front-panel UI boards with capacitive-touch replacement via ADC scanning, LED row driving, and seven-segment multiplexing. Its 25 I/O accommodate up to 7-segment digits plus key-matrix scanning, all driven from a single MCU. The 28 KB Flash holds UI state machines plus boot loader for field firmware updates via ICSP, and 1 KB RAM is sufficient for debounced key tables and LED PWM buffers.
تجویز کردہ
Handheld Test and Measurement Instruments
The PIC16F1518-I/SP fits entry-level handheld multimeters, cable testers, and logic-level probes because its 17-channel 10-bit ADC digitizes voltage, current, and resistance measurements while the 20 MHz CPU executes RMS math in real time. The XLP profile lets a handheld run for hundreds of hours on two AA cells. The ICSP/ICD pins enable field re-flashing via a 6-pin header without removing the chip.
تجویز کردہ
Industrial Process Sensor Conditioning
In factory-floor 4-20 mA loop and 0-10 V sensor signal conditioners, the PIC16F1518-I/SP converts analog signals, applies linearization, and drives isolated HART modem front-ends. The 10-bit ADC at 8-channel mux provides adequate resolution for 1% process instrumentation, and the SPDIP-28 socketed form simplifies replacement on legacy PLC backplanes. Industrial -40C to +85C temperature range matches IEC 60068-2-1 requirements for harsh environments.
تجویز کردہ
Automotive Interior Lighting and Switch Panels
Although the PIC16F1518-I/SP itself is not AEC-Q100 qualified, it is widely used in non-safety automotive interior accessories like dome-light controllers, RGB foot-well drivers, and capacitive switch panels. The 25 mA I/O source current directly drives LED strings up to 25 mA per channel; the 2 PWM channels create soft-fade transitions. Designers targeting AEC-Q100 should migrate to PIC16F1518-I/SPVAO variants or PIC18F equivalents.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16F1518-I/SP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16F1519-I/SP | PIC16F1518-I/SS | PIC16F1518-I/SO | PIC16F1517-I/SP | PIC16LF1518-I/SP |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SPDIP-28 | SPDIP-28 | SSOP-28 (SMD) | SOIC-28 (300 mil) | SPDIP-28 | SPDIP-28 |
| Program Memory (Flash) | 28 KB | 28 KB | 28 KB | 28 KB | 28 KB | 28 KB |
| RAM | 1 KB | ~1.5 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| CPU Max Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V |
| Number of I/O | 25 | 25 | 25 | 25 | 25 | 25 |
| ADC Channels x Resolution | 17 x 10-bit | 17 x 10-bit | 17 x 10-bit | 17 x 10-bit | 17 x 10-bit | 17 x 10-bit |
| XLP Low-Power Sleep | Yes (<100 nA typical) | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Industry-leading XLP sleep current below 100 nA (بمقابلہPIC16F1519-I/SP)
- Through-hole SPDIP-28 package for prototyping (بمقابلہPIC16F1518-I/SS)
- Lower voltage variant available in identical footprint (بمقابلہPIC16LF1518-I/SP)
ڈیزائن نوٹس
Place a 100 nF decoupling capacitor on the VDD pin (pin 17) and route the VSS pin (pin 16) directly to the ground plane with a short trace. For battery-powered designs, set the ULPBOR threshold to the lowest valid value (1.9 V on the F variant, 1.65 V on the LF variant) and enable the watchdog timer (WDT) with a long timeout to minimize wake frequency.
Keep the crystal traces (pin 5 OSC2 / pin 6 OSC1) short and symmetric, surrounded by a grounded guard ring to prevent digital switching noise from coupling into the oscillator. The ICSP pins (RB6/RB7) require a 6-pin header footprint on the PCB even if not populated in production - this allows in-field firmware updates without removing the MCU.
Do not apply voltages above 5.5 V to any pin - the absolute maximum on VDD is 7.5 V but logic pins only tolerate 5.5 V. Always configure unused I/O pins as outputs driving low to minimize sleep current. The MCLR pin (pin 18) must have a 10 kohm pull-up to VDD; without it, the device will see a brown-out reset on every power-up transient.
تعمیل کی معلومات
RoHS and REACH compliant per Microchip product page; not AEC-Q100 qualified - use automotive-qualified PIC16F variants or PIC18F equivalents for vehicular applications. Halogen-free per JEDEC JS709B.
