PIC16F1613-I/ST - 8-Bit MCU, 32MHz, 3.5KB Flash, XLP | Microchip
MPN: PIC16F1613-I/ST ✓ فعالPIC16F1613-I/ST جائزہ
An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory (Flash), data memory (RAM), and peripherals on one die. Within the broader semiconductor taxonomy, an MCU is a subset of microcontrollers, which in turn belong to the embedded processor class of integrated circuits. PIC microcontrollers use a RISC architecture with a small, fixed instruction set optimized for deterministic real-time control in cost- and power-sensitive embedded designs. The "XLP" (eXtreme Low Power) designation indicates Microchip's family of nanoWatt technology parts with sub-uA sleep currents for battery-powered applications.
Key differentiating features include the integrated 24-bit SMT for high-resolution time-of-flight, angle, or duty-cycle measurement in motor and lighting control, and on-chip zero-cross detect for TRIAC-based AC dimming without external zero-cross circuitry. The peripheral pin select (PPS) mapper allows remapping of digital peripherals to multiple I/O pins, simplifying PCB layout. With eXtreme Low Power (XLP) technology, the device typically consumes <30 nA in sleep with brown-out reset enabled, making it well-suited for always-on, battery-backed, or energy-harvesting systems.
The PIC16F1613 uses an enhanced mid-range 8-bit RISC core with a hardware multiplier, 16-level stack, and a 49-instruction set optimized for C and assembly development under MPLAB X IDE with the XC8 compiler. In-circuit debugging is supported via the two-wire ICD interface, and in-circuit serial programming (ICSP) allows firmware updates after PCB assembly. The 10-bit ADC supports up to 8 channels with an internal fixed voltage reference and a sample-and-hold front end.
Typical applications include small brushed-DC and stepper motor control, LED lighting with TRIAC dimming, capacitive-touch user interfaces, sensor signal conditioning, general-purpose digital I/O expansion, and low-power IoT edge nodes. The TSSOP-14 footprint makes it attractive where PCB area is constrained and pin count beyond 8 is needed.
When designing with this part, plan current budget for active and sleep modes against battery capacity, place a 0.1 uF decoupling capacitor within 5 mm of VDD, and reserve one I/O pin as ICSPCLK/ICSPDAT for in-circuit serial programming. Note that the PIC16F1613 has 14 pins; if more I/O is required, the PIC16F1613 family also offers 8- and 16-pin variants on the same silicon, with code compatibility preserved.
This page synthesizes distributor pricing for the PIC16F1613-I/ST, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
کے لیے ڈراپ اِن متبادل PIC16F1613-I/ST — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16F1613-I/ST (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Operating Temperature, ADC, Program Memory (Flash), Timers.
PIC16F1613-E/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1613T-I/ST
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC16F1503-I/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1455-I/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1574-I/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F15225-I/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F1613-I/ST زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | PIC16 (8-bit RISC, enhanced mid-range) |
| Program Memory (Flash) | 3.5 KB (2K x 14 words) |
| Data RAM | 256 bytes |
| Maximum CPU Frequency | 32 MHz |
| Operating Voltage Range | 2.3 V to 5.5 V |
| آپریٹنگ درجہ حرارت رینج | -40C to +85C (Industrial, "I") |
| ADC | 10-bit, up to 8 channels |
| Capture/Compare/PWM (CCP) | Yes |
| 24-bit Signal Measurement Timer (SMT) | Yes |
| Zero-Cross Detection | Yes (on-chip) |
| Peripheral Pin Select (PPS) | Yes |
| XLP (eXtreme Low Power) Sleep Current | <30 nA typical (with BOR enabled) |
| پیکیج | TSSOP-14 (ST) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| RoHS اسٹیٹس | Compliant |
| Lead-Free | Yes |
| Programming Interface | ICSP (2-wire), ICD |
PIC16F1613-I/ST پن کنفیگریشن
| پن 1 | RA3/AN3/C1IN+/ZCD — GPIO RA3 / Analog input 3 / Comparator input / Zero-Cross Detect input |
| پن 2 | RA4/AN4/C1OUT — GPIO RA4 / Analog input 4 / Comparator 1 output |
| پن 3 | RA5/MCLR/VPP — GPIO RA5 / Master Clear (reset) / Programming voltage |
| پن 4 | VDD — Positive supply voltage (2.3V to 5.5V) |
| پن 5 | VSS — Ground reference |
| پن 6 | RB4/AN10/SDA1 — GPIO RB4 / Analog input 10 / I2C SDA (via PPS) |
| پن 7 | RB5/AN11/RX/DT — GPIO RB5 / Analog input 11 / EUSART RX / Data |
| پن 8 | RB6/ICSPCLK/SCK — GPIO RB6 / ICSP clock / SPI SCK (via PPS) |
| پن 9 | RB7/ICSPDAT/SDI — GPIO RB7 / ICSP data / SPI SDI (via PPS) |
| پن 10 | RA0/AN0/C12IN0- — GPIO RA0 / Analog input 0 / Comparator input |
| پن 11 | RA1/AN1/C12IN1- — GPIO RA1 / Analog input 1 / Comparator input |
| پن 12 | RA2/AN2/TX/CK — GPIO RA2 / Analog input 2 / EUSART TX / Clock |
| پن 13 | RC0/SOSCFO/PWM — GPIO RC0 / Secondary oscillator output / PWM output |
| پن 14 | RC1/SMT1SIG/CCP1 — GPIO RC1 / SMT signal / CCP1 output |
عام استعمالات
PIC16F1613-I/ST کے لیے موزوں ہے 7 ایپلیکیشنs: TRIAC AC Dimmer with Zero-Cross Detect, Small Brushed DC Motor Control, Capacitive Touch User Interface, Battery-Powered IoT Edge Sensor Node, LED Lighting Driver with Dimming, General-Purpose Digital I/O Expansion, Hobbyist and Educational Embedded Projects.
TRIAC AC Dimmer with Zero-Cross Detect
The PIC16F1613-I/ST is uniquely suited for TRIAC-based AC dimmers because its on-chip zero-cross detection eliminates the external optocoupler zero-cross circuit. The 24-bit SMT can measure the AC line angle to within nanoseconds for accurate phase-angle or forward/reverse phase-cut dimming. The XLP <30 nA sleep current enables always-listening wall switches drawing minimal standby power from capacitive droppers. Place a 0.1 uF decoupling capacitor within 5 mm of VDD.
تجویز کردہ
Small Brushed DC Motor Control
The PIC16F1613-I/ST's integrated CCP module and 24-bit SMT make it well-suited for closed-loop brushed DC motor control. The 10-bit ADC reads back-EMF or current-sense feedback, while the CCP generates PWM at up to 32 MHz instruction rate. Peripheral Pin Select (PPS) lets the designer route PWM, fault, and brake signals to any I/O pin without board rework, reducing layout complexity in tight TSSOP-14 designs.
تجویز کردہ
Capacitive Touch User Interface
With its low-power XLP technology, the PIC16F1613-I/ST is ideal for capacitive touch keypads on battery-powered remote controls and appliances. The integrated SMT supports capacitive touch scanning algorithms, while PPS allows reassignment of touch channels to multiple pins. Sleep current below 30 nA means a CR2032 coin cell can power the touch interface for years of standby operation.
تجویز کردہ
Battery-Powered IoT Edge Sensor Node
The PIC16F1613-I/ST's <30 nA sleep current and 2.3V minimum supply make it an excellent edge-node MCU for IoT sensor applications, especially when paired with a low-power radio module over UART or SPI. Its 10-bit ADC can read analog sensors directly, and the XLP sleep retains RAM and limited peripherals for instant wake. Recommended for sub-1 GHz or BLE-connected thermostats, water meters, and remote controls.
تجویز کردہ
LED Lighting Driver with Dimming
For constant-current LED drivers with analog or PWM dimming, the PIC16F1613-I/ST integrates the 10-bit ADC to read light-level sensors and the CCP module to generate PWM dimming at up to 32 MHz. The XLP sleep allows the LED driver to enter micro-watt standby when the lamp is off. Compatible with constant-current driver ICs such as the AL8860 via analog dimming input.
تجویز کردہ
General-Purpose Digital I/O Expansion
In designs where a host processor lacks sufficient GPIO or PWM channels, the PIC16F1613-I/ST can serve as an I/O expander communicating via I2C or SPI. Its PPS mapper routes any peripheral to any I/O pin, simplifying PCB layout. The TSSOP-14 footprint is easy to hand-solder for prototypes, and the same PIC16 silicon runs the same firmware at 32 MHz for low-latency I/O.
تجویز کردہ
Hobbyist and Educational Embedded Projects
The PIC16F1613-I/ST, paired with MPLAB X IDE and the XC8 compiler (free version), is a popular choice for hobbyists learning 8-bit embedded development. The TSSOP-14 footprint is easy to solder on breakout boards, and ICSP allows in-circuit programming without removing the chip. Project ideas include line-following robots, custom alarm clocks, and small appliances.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16F1613-I/ST — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16F1613-E/ST | PIC16F1613T-I/ST | PIC16F1503-I/ST | PIC16F1455-I/ST | PIC16F1574-I/ST |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TSSOP-14 (ST) | TSSOP-14 (ST) - same | TSSOP-14 (ST) - same | TSSOP-14 (ST) - same | TSSOP-14 (ST) - same | TSSOP-14 (ST) - same |
| Core | PIC16 (8-bit RISC) | PIC16 (8-bit RISC) | PIC16 (8-bit RISC) | PIC16 (8-bit RISC) | PIC16 (8-bit RISC) with USB | PIC16 (8-bit RISC) |
| Flash Memory | 3.5 KB | 3.5 KB | 3.5 KB | 3.5 KB | 14 KB | 7 KB |
| RAM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 1 KB | 512 bytes |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 20 MHz | 48 MHz | 32 MHz |
| Operating Voltage | 2.3V to 5.5V | 2.3V to 5.5V | 2.3V to 5.5V | 2.3V to 5.5V | 2.3V to 5.5V | 2.3V to 5.5V |
| XLP (eXtreme Low Power) | Yes (<30 nA sleep) | Yes | Yes | Yes | Yes | Yes |
| Zero-Cross Detect | Yes (on-chip) | Yes | Yes | No | No | No |
اہم امتیازی خصوصیات
- Integrated on-chip zero-cross detection eliminates external optocoupler circuit (بمقابلہPIC16F1503-I/ST)
- Includes 24-bit Signal Measurement Timer for high-resolution timing (بمقابلہPIC16F1455-I/ST)
- Peripheral Pin Select (PPS) allows flexible signal routing (بمقابلہPIC16F1574-I/ST)
ڈیزائن نوٹس
Place a 0.1 uF decoupling capacitor within 5 mm of the VDD pin (pin 4) and a bulk capacitor (1-10 uF) on the same supply trace to handle inrush during MCU wake. The XLP <30 nA sleep current assumes BOR is enabled; if you disable BOR, idle current may rise. For battery-powered designs, use Sleep + WDT or Sleep + external interrupt wake to achieve the lowest average current.
The TSSOP-14 footprint is hand-solderable with a fine tip, but for production use proper SMT pads with a 1:1 footprint ratio. Keep the ICSP pins (RB6/ICSPCLK and RB7/ICSPDAT) accessible - either route them to a 2x3 or 1x6 header or expose test pads - so that MPLAB X with PICkit 4 can program/debug the board after assembly.
Do not tie MCLR (pin 3, RA5/MCLR/VPP) directly to VDD without a 10 kohm pull-up - the ICSP programmer needs to drive this pin low for reset. Configuration bits must be set in code (e.g., #pragma config) to enable or disable features like watchdog, BOR, and LVP; forgetting this is a common source of confusion. The Peripheral Pin Select (PPS) mapper must be unlocked (PPSLOCK = 0x55, 0xAA sequence) before reassigning peripheral functions.
The zero-cross detect input has a maximum input voltage spec - route the AC-derived signal through a current-limiting resistor and clamp network. For TRIAC dimming, use a snubber RC network across the TRIAC (typically 100 ohm + 0.01 uF) to limit dv/dt and prevent false triggering. The 24-bit SMT input pin can be sensitive to noise; place the SMT signal trace away from switching power lines and add a small RC filter if needed.
تعمیل کی معلومات
RoHS compliant per Microchip product page. Industrial temperature grade (-40C to +85C); AEC-Q100 qualified variants are not available in this part - choose automotive-grade PICs from other PIC16 families if AEC-Q100 is required.
