PIC16F753T-I/ST - 8-Bit MCU, 3.5KB Flash, 14-TSSOP | Microchip
MPN: PIC16F753T-I/ST ✓ فعالPIC16F753T-I/ST جائزہ
A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), working RAM, and a range of peripheral IP blocks such as ADC, timers, comparators, and communication peripherals. The PIC16F753 belongs to Microchip's PIC® 16F sub-family positioned between 8-pin baseline parts and higher-pin PIC18/dsPIC parts, used widely in cost-sensitive consumer, appliance, lighting, and industrial sensor applications where minimal BOM and on-chip analog integration matter more than absolute compute throughput.
Key integrated peripherals include one operational amplifier, two high-speed analog comparators (50 ns propagation delay), one Capture/Compare/PWM (ECCP) module, an 8-channel 10-bit ADC with internal voltage reference, one dual-range 9-bit DAC, an internal 8 MHz oscillator, and support for an external 32 kHz secondary oscillator. Brown-out Reset (BOR), Power-On Reset (POR), a Watchdog Timer (WDT) with its own on-chip low-power oscillator, and an In-Circuit Serial Programming (ICSP) interface are also provided.
The architecture is based on a 14-bit instruction word with a hardware stack and an interrupt controller; the enhanced mid-range core adds hardware-context save on interrupt entry/exit, reducing ISR overhead. The internal 8 MHz oscillator is factory calibrated and paired with a Phase-Locked Loop giving selectable 8/16/32/500 kHz LF operating modes for low-power sleep operation, allowing the designer to trade throughput against quiescent current.
Typical applications include LED lighting drivers, battery chargers, sensor signal conditioning, small BLDC/PWM motor control loops, and white-goods user interface boards. The internal op-amp and comparators remove the need for external analog front-ends, while the 9-bit DAC allows slope compensation in switch-mode and Li-ion charging topologies without external references.
When designing with this part, choose decoupling per Microchip AN576 (one 100 nF plus one bulk cap per VDD pin) and respect the 14-pin TSSOP's 1.0 mm pitch reflow profile to avoid tombstoning during reflow. If a 20-pin variant is preferred for additional I/O, the PIC16F767/777 family drops in with the same peripheral set.
کے لیے ڈراپ اِن متبادل PIC16F753T-I/ST — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16F753T-I/ST (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Comparators, Package, ADC, Core Architecture, I/O Pins.
PIC16F753-I/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F753-E/ST
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F753-I/SL
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F753T-I/ST زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core | PIC16 enhanced mid-range 8-bit RISC |
| Instruction Set Size | 35 single-word instructions |
| Program Memory (Flash) | 3.5 KB (2K x 14) |
| RAM | 128 bytes |
| Max CPU Speed | 20 MHz (200 ns instruction cycle) |
| Internal Oscillator | 8 MHz calibrated |
| Operating Voltage | 2.0 V to 5.5 V |
| آپریٹنگ درجہ حرارت | -40C to +85C (industrial, I grade) |
| ADC | 8-channel, 10-bit |
| DAC | 1 x 9-bit dual-range |
| Comparators | 2 x high-speed (50 ns propagation delay) |
| Operational Amplifier | 1 x on-chip |
| PWM / CCP | 1 x Enhanced CCP (ECCP) |
| Watchdog Timer | Yes, with dedicated low-power oscillator |
| Brown-out Reset / POR | Yes |
| Programming Interface | ICSP (In-Circuit Serial Programming) |
| پیکیج | 14-pin TSSOP (4.4 mm body, 1.0 mm pitch) |
| ماؤنٹنگ ٹائپ | Surface Mount (Tape & Reel, -T suffix) |
| RoHS اسٹیٹس | Compliant |
| Lead-Free | Yes |
PIC16F753T-I/ST پن کنفیگریشن
| پن 1 | RA0/AN0/C1IN+/ICSPCLK — Bidirectional I/O / Analog input 0 / Comparator 1 non-inverting / ICSP clock |
| پن 2 | RA1/AN1/C1IN-/VREF-/ICSPI — Bidirectional I/O / Analog input 1 / Comparator 1 inverting / VREF- / ICSP I/O |
| پن 3 | RA2/AN2 — Bidirectional I/O / Analog input 2 |
| پن 4 | RA3/MCLR/VPP — Bidirectional I/O / Master Clear reset (active low) / Programming voltage |
| پن 5 | RA4/AN3/T0CKI/C1OUT — Bidirectional I/O / Analog input 3 / Timer0 clock input / Comparator 1 output |
| پن 6 | VSS — Ground reference |
| پن 7 | RA5/AN4/C2IN+/DAC/VREF+ — Bidirectional I/O / Analog input 4 / Comparator 2 non-inverting / DAC output / VREF+ |
| پن 8 | RA6/AN5/OSC2/CLKOUT — Bidirectional I/O / Analog input 5 / Crystal out / Clock out |
| پن 9 | RA7/AN6/OSC1/CLKIN — Bidirectional I/O / Analog input 6 / Crystal in / Clock in |
| پن 10 | RC0/AN8/C2IN-/INT/COG — Bidirectional I/O / Analog input 8 / Comparator 2 inverting / External interrupt / PWM |
| پن 11 | RC1/SDO/COG — Bidirectional I/O / SPI data out / PWM |
| پن 12 | RC2/CCP1/P1A/COG — Bidirectional I/O / Capture/Compare/PWM / PWM output / PWM |
| پن 13 | RC3/AN7/COG/OPA1IN+ — Bidirectional I/O / Analog input 7 / PWM / Op-amp 1 non-inverting input |
| پن 14 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
عام استعمالات
PIC16F753T-I/ST کے لیے موزوں ہے 7 ایپلیکیشنs: LED Lighting Drivers, Battery Charger / Fuel-Gauge Front-End, Sensor Signal Conditioning, Small BLDC / Fan Motor PWM Control, White Goods / User Interface Boards, Industrial Sensor / Process Controller, Consumer Remote Control / IR Emitter.
LED Lighting Drivers
The PIC16F753T-I/ST is well-suited for LED lighting drivers because its integrated 10-bit ADC, on-chip op-amp, and Enhanced CCP (ECCP) PWM module eliminate external driver ICs. The 9-bit dual-range DAC enables closed-loop current control via analog peak-current-mode regulation, while the 32 kHz LF oscillator reduces standby consumption below 1 uA for ENERGY STAR-compliant standby. With 3.5 KB Flash and 128 B RAM, it handles color-mixing firmware and DMX or 0-10 V dimming inputs in a single 14-TSSOP device.
تجویز کردہ
Battery Charger / Fuel-Gauge Front-End
For Lithium-ion and NiMH charger designs, the PIC16F753T-I/ST integrates the two high-speed comparators (50 ns) needed for slope compensation and current-sense peak detection, plus the 9-bit DAC that sets the charge-current reference. The internal 8 MHz oscillator with PLL supports accurate ADC sampling of battery voltage and current at 20 MHz CPU speed. Its -40C to +85C industrial range covers the thermal envelope of sealed charger bays.
تجویز کردہ
Sensor Signal Conditioning
The PIC16F753T-I/ST replaces a discrete analog front-end (op-amp + comparator + MCU) by integrating one on-chip op-amp, two high-speed comparators, an 8-channel 10-bit ADC, and a 9-bit DAC. Thermocouple, thermistor, photodiode, and strain-gauge signal conditioning is feasible with the on-chip op-amp providing reference-scaled gain before the ADC. The 3.5 KB Flash holds calibration tables while the 128 B RAM provides working space for moving-average filtering.
تجویز کردہ
Small BLDC / Fan Motor PWM Control
The PIC16F753T-I/ST's Enhanced CCP (ECCP) module with complementary PWM outputs drives half-bridge and full-bridge low-voltage motor drivers for small BLDC fans, pumps, and stepper coils. Hardware shutdown on overcurrent events uses one of the 50 ns comparators referenced to a sense resistor; the other comparator can be reused as BEMF zero-cross detection for sensorless trapezoidal commutation. At 20 MHz instruction rate, the firmware control loop has 200 ns tick resolution.
تجویز کردہ
White Goods / User Interface Boards
In washing machines, dishwashers, and ovens, the PIC16F753T-I/ST serves as a keypad/LED driver slave MCU taking the load off a larger host CPU. The 9-bit DAC and 10-bit ADC digitize rotary-knob positions and temperature probes, while the ECCP generates tone/sounder drives. With industrial-grade -40C to +85C operation and a 14-TSSOP package, it fits behind the control panel with standard reflow profile and supports ICSP over a 5-pin header for production line programming.
تجویز کردہ
Industrial Sensor / Process Controller
The PIC16F753T-I/ST provides a small-footprint control node for industrial 4-20 mA loops and discrete-binary sensor aggregators. Its 2.0-5.5 V supply range accepts 24 V industrial rails with a simple LDO pre-regulator, and its comparators act as threshold detectors for fast signal edges without software polling. With BOR, POR, and a dedicated Watchdog Timer on its own low-power oscillator, the part meets typical IEC 61010 industrial reliability requirements for a 14-pin TSSOP decentralized controller.
تجویز کردہ
Consumer Remote Control / IR Emitter
The PIC16F753T-I/ST can drive an IR LED via its ECCP PWM with carrier frequency up to 20 MHz CPU clock driving precise 38 kHz modulation. The internal 8 MHz oscillator with PLL maintains stable timing during 2.0-5.5 V battery droop, and the 9-bit DAC provides intensity control for bidirectional IR or as a temperature reference for the internal sensor. Low-power 32 kHz LF mode extends coin-cell life in remote controls.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16F753T-I/ST — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16F753-I/ST | PIC16F753-E/ST | PIC16F753-I/SL |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology (same) | Microchip Technology (same) | Microchip Technology (same) |
| Package | 14-TSSOP (4.4 mm, 1.0 mm pitch) | 14-TSSOP - same | 14-TSSOP - same | 14-SOIC - same pin count, wider body |
| Program Memory (Flash) | 3.5 KB (2K x 14) | 3.5 KB | 3.5 KB | 3.5 KB |
| RAM | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| Max CPU Clock | 20 MHz (200 ns) | 20 MHz | 20 MHz | 20 MHz |
| Operating Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| Operating Temperature Grade | -40C to +85C (I) | -40C to +85C (I) | -40C to +125C (E extended) | -40C to +85C (I) |
| Shipping Packaging | Tape & Reel (T suffix) | Tube (no -T) | Tube | Tube |
اہم امتیازی خصوصیات
- Pin-to-pin TSSOP with extended temperature grade (بمقابلہPIC16F753-E/ST)
- Tape-and-reel mass-production packaging (بمقابلہPIC16F753-I/ST)
- Wider body SOIC for hand-solder prototyping (بمقابلہPIC16F753-I/SL)
ڈیزائن نوٹس
Per Microchip application note AN576 (Decoupling and PCB Layout for PICmicro MCUs), place a 100 nF X7R ceramic decoupling capacitor as close as possible to the VDD pin with the trace going to the IC directly (no via between pad and capacitor). Add a 1-10 uF bulk tantalum or ceramic cap on the same power rail to source switching transients from the ECCP PWM and internal ADC reference. The 14-TSSOP 1.0 mm pitch requires standard reflow profile (per IPC JEDEC J-STD-020), but layout the package with 0.4 mm-wide traces to avoid solder bridging.
The PIC16F753T-I/ST has NO true Data EEPROM according to the PIC16F753 datasheet; for non-volatile storage of calibration or running values, use the Flash self-write feature with row-erase discipline and apply wear-leveling in firmware. Mishandling MCLR (RA3 pin) as plain I/O without proper in-circuit programming access can brick the part - always provide a guarded ICSP header (5-pin: VPP, VDD, VSS, ICSPCLK, ICSPDAT) on prototype boards or a guarded test pad on production boards.
The integrated 8 MHz HFINTOSC is factory calibrated; for applications needing accurate RS-232 baud rates or PWM frequency stability, switch to an external 20 MHz crystal on RA6/RA7 (OSC2/OSC1). Estimated: with all peripherals enabled the typical active current consumption is below 2 mA at 5 V and 20 MHz, while LFINTOSC sleep with WDT off can fall below 1 uA - always verify against the data sheet's Electrical Characteristics table for your specific code execution profile.
When using the on-chip op-amp or comparator inputs as analog signals, keep digital traces at least 5 mm away on the same layer and stitch a ground guard ring around sensitive analog nodes to reduce noise coupling from RA5/MCLR digital transitions. The internal voltage reference is shared with the 10-bit ADC and 9-bit DAC - if high-precision measurements are required, buffer the reference at the VREF pin with a low-impedance external op-amp follower (e.g., MCP6001) and avoid switching high-current loads during ADC conversion windows.
تعمیل کی معلومات
RoHS compliant per Microchip product page. Industrial -40C to +85C grade (I); extended -40C to +125C grade (E) also available. Not AEC-Q100 automotive qualified.
