PIC16F77T-E/PT - 8-Bit 20MHz 14KB Flash MCU TQFP-44 | Microchip
MPN: PIC16F77T-E/PT ✓ فعالPIC16F77T-E/PT جائزہ
An 8-bit PIC microcontroller is a Harvard-architecture RISC processor widely used in embedded control applications; it executes one instruction per cycle (except branches) and integrates Flash program memory, RAM, peripherals (ADC, comparators, timers, USART, PWM, etc.), and a brown-out reset into a single IC. Positioned in the broader hierarchy, PIC16 MCUs sit above PIC10/PIC12 baseline parts and below PIC18/PIC24 enhanced parts, and within Microchip's lineup they serve cost-sensitive real-time control tasks where deterministic interrupt latency and mature toolchain support are valued.
Key features of the PIC16F77T-E/PT include five 8-bit I/O ports providing up to 33 digital I/O pins, a 10-bit multi-channel ADC, two analog comparators, three timers (Timer0, Timer1, Timer2), a USART with 9-bit address detection, capture/compare/PWM modules, and an internal watchdog timer. The device also supports in-circuit serial programming (ICSP) for field updates.
Architecture-wise, the PIC16F77 uses a 14-bit instruction word and 35 single-word instructions, enabling a 200 ns instruction cycle at 20 MHz. Internal RC oscillator options reduce external component count, while the enhanced CCP module simplifies motor-control and SMPS designs. The brown-out reset and power-on reset circuitry improve robustness in industrial environments.
Typical applications include industrial automation controllers, motor control subsystems (BLDC, stepper, relay drive), digital signal conditioning, consumer appliance control panels, HVAC and thermostat front-ends, sensor signal preprocessing, and automotive interior accessories (non-safety). It is also a common drop-in choice for upgrading legacy PIC16C/PIC16F designs that need additional code space.
When designing with this part, allocate the oscillator and MCLR circuitry per datasheet recommendations and verify ADC acquisition time against source impedance. Programming via ICSP requires a 4-pin header with proper isolation to avoid loading the signals during debug.
This page consolidates distributor pricing, drop-in alternatives in the same TQFP-44 footprint, and design notes that complement - but do not replace - the manufacturer datasheet.
کے لیے ڈراپ اِن متبادل PIC16F77T-E/PT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16F77T-E/PT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Core Architecture, Timers, I/O Pins, ADC.
PIC16F77T-E/L
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F777T-I/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F777-E/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F777-I/ML
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F77-I/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F77T-E/PT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | PIC16 8-bit RISC (Harvard) |
| Instruction Word Size | 14-bit |
| Program Memory (Flash) | 14 KB (8K x 14) |
| RAM | 368 bytes |
| Clock Speed (max) | 20 MHz |
| Instruction Cycle | 200 ns at 20 MHz |
| سپلائی وولٹیج | 4.0 V to 5.5 V |
| I/O Pins | 33 (5 ports) |
| ADC | 10-bit, multi-channel |
| Timers | 3 (Timer0, Timer1, Timer2) |
| Analog Comparators | 2 |
| Communication | USART (with 9-bit address detect) |
| PWM / CCP | Yes (Capture/Compare/PWM) |
| Watchdog Timer | Yes (internal) |
| Brown-out Reset | Yes |
| Operating Temperature (E suffix) | -40C to +125C (industrial) |
| پیکیج | TQFP-44 (10x10 mm, also called PT) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| RoHS اسٹیٹس | Compliant |
| Programming | ICSP (In-Circuit Serial Programming) |
PIC16F77T-E/PT پن کنفیگریشن
| پن 1 | OSC1/CLKI — Crystal oscillator input or external clock input |
| پن 2 | OSC2/CLKO — Crystal oscillator output or clock output |
| پن 3 | MCLR/VPP — Master Clear (reset) input or programming voltage |
| پن 4 | RA0/AN0 — PORTA bit 0 / Analog input channel 0 |
| پن 5 | RA1/AN1 — PORTA bit 1 / Analog input channel 1 |
| پن 6 | RA2/AN2 — PORTA bit 2 / Analog input channel 2 |
| پن 7 | RA3/AN3/VREF — PORTA bit 3 / Analog input channel 3 / Voltage reference |
| پن 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| پن 9 | RA5/AN4/SS — PORTA bit 5 / Analog input channel 4 / SPI slave select |
| پن 10 | RE0/RD/AN5 — PORTE bit 0 / Parallel port read / Analog input 5 |
| پن 11 | RE1/WR/AN6 — PORTE bit 1 / Parallel port write / Analog input 6 |
| پن 12 | RE2/CS/AN7 — PORTE bit 2 / Parallel port chip select / Analog input 7 |
| پن 13 | VSS — Ground reference |
| پن 14 | VDD — Positive supply voltage 4.0V-5.5V |
| پن 15 | OSC1 — Secondary oscillator pin (alternate) |
| پن 16 | OSC2 — Secondary oscillator pin (alternate) |
| پن 17 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock |
| پن 18 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 module |
| پن 19 | RC2/CCP1 — PORTC bit 2 / CCP1 module |
| پن 20 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| پن 21 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| پن 22 | RC5/SDO — PORTC bit 5 / SPI data out |
| پن 23 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| پن 24 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| پن 25 | RB0/INT — PORTB bit 0 / external interrupt input |
| پن 26 | RB1 — PORTB bit 1 |
| پن 27 | RB2 — PORTB bit 2 |
| پن 28 | RB3/PGM — PORTB bit 3 / low-voltage programming enable |
| پن 29 | RB4 — PORTB bit 4 / interrupt-on-change |
| پن 30 | RB5 — PORTB bit 5 / interrupt-on-change |
| پن 31 | RB6/PGC — PORTB bit 6 / ICSP clock |
| پن 32 | RB7/PGD — PORTB bit 7 / ICSP data |
| پن 33 | RD0 — PORTD bit 0 / parallel data bus |
| پن 34 | RD1 — PORTD bit 1 / parallel data bus |
| پن 35 | RD2 — PORTD bit 2 / parallel data bus |
| پن 36 | RD3 — PORTD bit 3 / parallel data bus |
| پن 37 | RD4 — PORTD bit 4 / parallel data bus |
| پن 38 | RD5 — PORTD bit 5 / parallel data bus |
| پن 39 | RD6 — PORTD bit 6 / parallel data bus |
| پن 40 | RD7/PSP7 — PORTD bit 7 / parallel slave port data |
| پن 41 | AVSS — Analog ground reference |
| پن 42 | AVDD — Analog positive supply |
| پن 43 | VSS — Ground reference (digital) |
| پن 44 | VDD — Positive supply voltage (digital) |
عام استعمالات
PIC16F77T-E/PT کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Controllers, Motor Control Subsystems, HVAC and Thermostat Front-Ends, Consumer Appliance Control, Sensor Signal Preprocessing, Automotive Interior Accessories (Non-Safety).
Industrial Automation Controllers
The PIC16F77T-E/PT fits industrial automation controllers because it combines 14 KB of Flash with deterministic 200 ns instruction cycles, 33 digital I/O lines, and a wide 4.0V-5.5V supply range. Its on-chip USART and analog comparators handle RS-485 sensor interfaces directly, while the 20 MHz clock supports 9-bit address detect protocols common in factory automation. The TQFP-44 footprint simplifies SMT assembly for control-cabinet PCBs and reduces cost per I/O line.
تجویز کردہ
Motor Control Subsystems
The PIC16F77T-E/PT works well in motor control subsystems because its Capture/Compare/PWM modules and 20 MHz instruction rate deliver accurate commutation timing for brushed DC and small BLDC motors. The integrated 10-bit ADC samples back-EMF or current-sense signals fast enough to support 20 kHz PWM, while the 33 I/O lines accept quadrature encoders and direction logic. The TQFP-44 footprint tolerates the thermal rise of continuous switching through built-in brown-out reset protection.
تجویز کردہ
HVAC and Thermostat Front-Ends
The PIC16F77T-E/PT suits HVAC and thermostat front-ends because its 10-bit ADC and analog comparators handle NTC thermistor networks and supply-voltage monitoring with sufficient resolution. The 14 KB Flash stores scheduling logic, while the 368-byte RAM covers setpoint buffers and UI state. Low-power modes plus brown-out reset extend battery life during brown-outs common in HVAC wiring, all within the industry-standard 5V supply range.
تجویز کردہ
Consumer Appliance Control
The PIC16F77T-E/PT serves consumer appliance control panels due to its 33 I/O pins driving LED indicators, keypad matrices, and 7-segment displays. The ICSP interface supports in-field firmware updates after assembly, while 5V supply compatibility eliminates level shifters for legacy appliance power rails. The TQFP-44 footprint supports both hand-soldered prototypes and high-volume SMT production runs.
تجویز کردہ
Sensor Signal Preprocessing
The PIC16F77T-E/PT integrates sensor preprocessing through its 10-bit ADC, two analog comparators, and hardware USART, accepting raw sensor voltages and transmitting conditioned values over UART. The 20 MHz clock keeps ADC sampling latency under 10 us, supporting vibration and pressure monitoring up to several kHz. Industrial-grade -40C to +125C operation suits outdoor enclosures and process instrumentation.
تجویز کردہ
Automotive Interior Accessories (Non-Safety)
The PIC16F77T-E/PT powers non-safety automotive interior accessories such as lighting controllers, seat-position memories, and accessory timers. The extended -40C to +125C temperature window tolerates cabin and engine-bay-adjacent environments, while the 14 KB Flash covers the most accessory sequencing stacks. Brown-out reset and watchdog timer improve robustness against cranking transients on 12V rails.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16F77T-E/PT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16F777T-I/PT | PIC16F777-E/PT | PIC16F77-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-44 (PT) | TQFP-44 (PT) - same | TQFP-44 (PT) - same | TQFP-44 (PT) - same |
| Flash Program Memory | 14 KB | 14 KB | 14 KB | 14 KB |
| RAM | 368 bytes | 368 bytes | 368 bytes | 368 bytes |
| Max Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| I/O Pins | 33 | 33 | 33 | 33 |
| ADC | 10-bit | 10/12-bit selectable | 10/12-bit selectable | 10-bit |
| nanoWatt Power Management | No | Yes | Yes | No |
| Temperature Range | -40C to +125C | -40C to +85C | -40C to +125C | -40C to +85C |
اہم امتیازی خصوصیات
- Lower cost baseline with mature PIC16F feature set (بمقابلہPIC16F777T-I/PT)
- Extended temperature range option on E suffix (بمقابلہPIC16F77-I/PT)
- Larger I/O count than lower-pin PIC16F cousins (بمقابلہPIC16F76T-E/SO)
ڈیزائن نوٹس
The PIC16F77T-E/PT operates from 4.0V to 5.5V. Brown-out reset typically triggers at 3.6V-4.0V to protect Flash during voltage dips. Add a 100nF decoupling capacitor within 5 mm of VDD pin 14 and an additional 10uF bulk capacitor on the supply rail to handle motor-control inrush without sag.
Keep the crystal traces between OSC1 and OSC2 as short and symmetric as possible, surrounded by a digital ground guard ring. AVDD/AVSS should have their own ferrite or LC filter stage to isolate analog supply noise from the digital VDD, and AVDD must be connected even if the ADC is unused (ties to internal references).
MCLR must be pulled high through a 10k resistor and bypassed with a 100nF capacitor; floating MCLR causes spurious resets. RB3 must be held low during normal operation unless LVP programming is intended, or the device will enter low-voltage programming mode unintentionally. ICSP pins PGC/PGD should be isolated with series resistors during in-circuit debug to avoid loading the programming signals.
Long PORTD bus traces (>50 mm) benefit from series 100-ohm terminators and a ground reference trace to control reflections in high-speed parallel reads. PORTC SPI pins (RC3/RC4/RC5) require matched-length routing for signals above 5 MHz to maintain data integrity. If using the parallel slave port, the PSPI/O bits in TRISE must be cleared for proper operation.
تعمیل کی معلومات
RoHS compliance is indicated in the Microchip material declaration. The device is not AEC-Q100 qualified; for automotive-safety applications consider migrating to PIC16F1xxx or dsPIC30F families that carry AEC-Q100 grades.
