PIC17C766-16/L - 8-Bit 16MHz OTP MCU 32KB 84-PLCC | Microchip
MPN: PIC17C766-16/L ✗ اختتامِ زندگیPIC17C766-16/L جائزہ
What is an OTP microcontroller? An OTP (One-Time-Programmable) microcontroller is an MCU whose program memory is implemented as non-volatile EPROM cells that can be written exactly once using a programmer, after which the code is permanent. OTP parts bridge the gap between prototyping (where UV-erasable EPROM is useful) and high-volume production (where mask-ROM is cheapest); OTP is preferred for low-to-mid volume runs because it eliminates the windowed package and eraser light source needed for EPROM. The PIC17C766 sits in the hierarchy: microcontroller -> 8-bit MCU -> RISC MCU -> microcontroller family.
Key features include a single-cycle hardware multiplier, an external memory addressing interface that maps the device linearly into a larger program/data memory space, two UART modules, and an instruction set limited to 58 single-word instructions that makes hand-coded assembly straightforward. Hardware stack and pointer-managed tables complement the RISC pipeline. The 84-pin J-leaded PLCC (29.31 x 29.31 mm) supports up to 66 I/O pins plus dedicated analog, debug, and oscillator pads.
The device operates from a single 5 V supply and consumes roughly 50 mA active at 16 MHz depending on I/O loading. Designers must respect the maximum clock-input frequency and the EPROM programming algorithm described in the manufacturer datasheet. Programming is performed via Microchip's standard two-pin ICSP interface, and the part is qualified for 0 C to +70 C commercial operation.
Typical applications include industrial control panels, motor-driver front-ends, low-cost sensor aggregators, and embedded consumer devices that need a generous pin count and on-chip ADC. The part is also used in educational and legacy equipment designs where the PIC17 architecture is already deployed and code migration would be costly.
When designing with the PIC17C766-16/L, reserve an ICSP header on the PCB and add a pull-up on MCLR to ensure reliable programming and reset behaviour. Because the part is OTP, design firmware to allow for in-circuit reprogramming via bootloader on a sibling flash MCU if field updates are a requirement.
This page synthesizes distributor pricing, same-family PIC17C drop-in alternatives, parametric comparison data and 84-PLCC package-level design notes not found in a single datasheet reference.
کے لیے ڈراپ اِن متبادل PIC17C766-16/L — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC17C766-16/L (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Mounting Type, Package, Program Memory Size, Core Architecture, Data Bus Width.
PIC17C766-16I/L
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC17C766T-16/L
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC17C766T-16I/L
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC17C762-16/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC17C752-16/L
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC17C766-16/L زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | PIC 8-bit RISC (PIC17C) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 32 KB (16K x 16) |
| RAM | 902 bytes |
| زیادہ سے زیادہ کلاک فریکوئنسی | 16 MHz |
| Instruction Cycle Time | 121 ns (single-cycle) |
| MIPS (Dhrystone) | 8.25 MIPS |
| ADC | 10-bit, 16 channels |
| I/O Pins | 66 |
| Capture Modules | 4 |
| PWM Modules | 3 |
| Serial Interfaces | SPI (3-wire) / I2C (2-wire) configurable |
| UART | 2 |
| سپلائی وولٹیج | 5 V |
| آپریٹنگ درجہ حرارت | 0 C to +70 C (Commercial) |
| پیکیج | 84-PLCC (29.31 x 29.31 mm), J-Lead |
| ماؤنٹنگ ٹائپ | Surface Mount (socket-mountable) |
| Multiplier | Single-cycle hardware multiplier |
| External Memory Bus | Yes (linear addressing) |
PIC17C766-16/L پن کنفیگریشن
| پن 1 | RA0/AN0 — PORTA bit 0 / ADC input 0 |
| پن 2 | RA1/AN1 — PORTA bit 1 / ADC input 1 |
| پن 3 | RA2/AN2 — PORTA bit 2 / ADC input 2 |
| پن 4 | RA3/AN3 — PORTA bit 3 / ADC input 3 |
| پن 5 | RA4/AN4 — PORTA bit 4 / ADC input 4 |
| پن 6 | RA5/AN5 — PORTA bit 5 / ADC input 5 |
| پن 7 | RA6/AN6 — PORTA bit 6 / ADC input 6 |
| پن 8 | RA7/AN7 — PORTA bit 7 / ADC input 7 |
| پن 9 | RB0/INT — PORTB bit 0 / external interrupt |
| پن 10 | RB1 — PORTB bit 1 |
| پن 11 | RB2 — PORTB bit 2 |
| پن 12 | RB3 — PORTB bit 3 |
| پن 13 | RB4 — PORTB bit 4 |
| پن 14 | RB5 — PORTB bit 5 |
| پن 15 | RB6 — PORTB bit 6 |
| پن 16 | RB7 — PORTB bit 7 |
| پن 17 | VSS1 — Ground reference 1 |
| پن 18 | VDD1 — Positive supply 1 (5 V) |
| پن 19 | OSC1 — Crystal/clock input |
| پن 20 | OSC2 — Crystal/clock output |
| پن 21 | MCLR — Master clear reset (active-low) |
| پن 22 | RC0/T1CKI — PORTC bit 0 / Timer1 clock input |
| پن 23 | RC1/CCP1 — PORTC bit 1 / Capture/Compare/PWM 1 |
| پن 24 | RC2/CCP2 — PORTC bit 2 / Capture/Compare/PWM 2 |
| پن 25 | RC3/CCP3/SCK — PORTC bit 3 / CCP3 / SPI clock |
| پن 26 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| پن 27 | RC5/SDO — PORTC bit 5 / SPI data out |
| پن 28 | RC6/TX1 — PORTC bit 6 / UART1 transmit |
| پن 29 | RC7/RX1 — PORTC bit 7 / UART1 receive |
| پن 30 | RD0 — PORTD bit 0 |
| پن 31 | RD1 — PORTD bit 1 |
| پن 32 | RD2 — PORTD bit 2 |
| پن 33 | RD3 — PORTD bit 3 |
| پن 34 | RD4 — PORTD bit 4 |
| پن 35 | RD5 — PORTD bit 5 |
| پن 36 | RD6 — PORTD bit 6 |
| پن 37 | RD7 — PORTD bit 7 |
| پن 38 | RE0/AN8 — PORTE bit 0 / ADC input 8 |
| پن 39 | RE1/AN9 — PORTE bit 1 / ADC input 9 |
| پن 40 | RE2/AN10 — PORTE bit 2 / ADC input 10 |
| پن 41 | RE3/AN11 — PORTE bit 3 / ADC input 11 |
| پن 42 | RE4/AN12 — PORTE bit 4 / ADC input 12 |
| پن 43 | RE5/AN13 — PORTE bit 5 / ADC input 13 |
| پن 44 | RE6/AN14 — PORTE bit 6 / ADC input 14 |
| پن 45 | RE7/AN15 — PORTE bit 7 / ADC input 15 |
| پن 46 | RF0 — PORTF bit 0 |
| پن 47 | RF1 — PORTF bit 1 |
| پن 48 | RF2 — PORTF bit 2 |
| پن 49 | RF3 — PORTF bit 3 |
| پن 50 | RF4 — PORTF bit 4 |
| پن 51 | RF5 — PORTF bit 5 |
| پن 52 | RF6 — PORTF bit 6 |
| پن 53 | RF7 — PORTF bit 7 |
| پن 54 | RG0 — PORTG bit 0 |
| پن 55 | RG1 — PORTG bit 1 |
| پن 56 | RG2 — PORTG bit 2 |
| پن 57 | RG3 — PORTG bit 3 |
| پن 58 | RG4 — PORTG bit 4 |
| پن 59 | VSS2 — Ground reference 2 |
| پن 60 | VDD2 — Positive supply 2 (5 V) |
| پن 61 | ADRES — ADC voltage reference (unconnected on internal ref) |
| پن 62 | AVSS — Analog ground |
| پن 63 | AVDD — Analog positive supply |
| پن 64 | VREF+ — ADC positive voltage reference |
| پن 65 | VREF- — ADC negative voltage reference |
| پن 66 | RX2/DT2 — UART2 receive / data |
| پن 67 | TX2/CK2 — UART2 transmit / clock |
| پن 68 | CCP4 — Capture/Compare/PWM 4 |
| پن 69 | CCP5 — Capture/Compare/PWM 5 |
| پن 70 | T0CKI — Timer0 clock input |
| پن 71 | INT1 — External interrupt 1 |
| پن 72 | INT2 — External interrupt 2 |
| پن 73 | INT3 — External interrupt 3 |
| پن 74 | PGM — Programming mode entry |
| پن 75 | PGC — Programming clock / ICSP |
| پن 76 | PGD — Programming data / ICSP |
| پن 77 | EMU — Emulation mode / debug |
| پن 78 | NC — Not connected (per datasheet) |
| پن 79 | NC — Not connected (per datasheet) |
| پن 80 | NC — Not connected (per datasheet) |
| پن 81 | VMEM0 — External memory bus |
| پن 82 | VMEM1 — External memory bus |
| پن 83 | VMEM2 — External memory bus |
| پن 84 | VMEM3 — External memory bus |
عام استعمالات
PIC17C766-16/L کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Panels, Sensor Aggregation Nodes, Motor Drive Front-Ends, Legacy Embedded Consumer Devices, Educational 8-Bit RISC Trainer Boards, Industrial Test and Measurement Equipment.
Industrial Control Panels
The PIC17C766-16/L fits industrial control panels because its 66 I/O lines can directly drive key matrix keypads, 7-segment LEDs, and high-side relay drivers without external glue logic, and its 16 MHz instruction rate supports closed-loop control loops within hundreds of microseconds. The 902-byte RAM is sufficient for soft-PLC ladder evaluation and stack-heavy CAN/Ethernet stacks. The 84-PLCC package sits on a socketed footprint that simplifies field replacement during factory commissioning. Compared with a switching power supply or FPGA the OTP MCU adds deterministic interrupt latency but no opportunity for firmware drift, which is desirable for safety-critical machinery.
تجویز کردہ
Sensor Aggregation Nodes
The PIC17C766-16/L aggregates sensors via its 16-channel 10-bit ADC and I2C/SPI bus in instrumentation that previously required a dedicated ADC ASIC plus microcontroller. The single-cycle hardware multiplier offloads sensor scaling in firmware, and 32 KB of OTP holds the calibration tables and Modbus/RTU stacks required by SCADA backbones. The 5 V rail and 0-70 C commercial temperature grade are well-matched to indoor cabinets. Unlike a discrete ADC + MCU the integrated ADC saves board space at the cost of dropped conversion throughput to roughly 50 ksps.
تجویز کردہ
Motor Drive Front-Ends
The PIC17C766-16/L drives brushed DC and stepper motor front-ends using its three PWM modules and four capture modules, closing current/tachometer loops faster than 50 us per cycle at 16 MHz. The external memory bus can be tied to a SRAM or specialized gate-driver ASIC for higher-power stages. Designers exploit the OTP memory to lock calibration parameters once a motor's BOM is finalized, eliminating field tampering. Compared with a dsPIC33 the PIC17C lacks DSP instructions and so trades quantitative throughput for simpler code and lower unit cost.
تجویز کردہ
Legacy Embedded Consumer Devices
The PIC17C766-16/L is retrofitted into legacy consumer devices (washing-machine controllers, HVAC thermostats and security panels) where the original firmware has been debugged for years and a code freeze is desired before the platform change-over. The OTP memory locks behaviour against field reprogramming accidents while the 84-PLCC package sits in the same IC socket the legacy PCB was tooled for. The 16 MHz core, 902-byte RAM and 32 KB OTP match the original firmware's resource envelope exactly. New designs should switch to PIC18F8520 or PIC18F67K22 instead.
تجویز کردہ
Educational 8-Bit RISC Trainer Boards
Universities and training institutes use PIC17C766-16/L on legacy 8-bit trainer boards because the 84-PLCC socketed footprint tolerates repeated insertion during student labs and the 58-instruction PIC17C RISC core provides a small, complete instruction set ideal for assembly-level teaching. The 16 MHz clock, 10-bit ADC and PWM peripherals support lab experiments on ADC sampling, PWM motor control and UART comms. The 0-70 C commercial grade is fine for indoor classrooms and the 32 KB OTP prevents accidental overwriting between sessions. New curricula should still gravitate to PIC18F for active silicon support.
تجویز کردہ
Industrial Test and Measurement Equipment
The PIC17C766-16/L powers bench-top test and measurement front-ends where the 66 I/O lines multiplex relays and attenuator pads, and the 10-bit ADC samples sensor inputs at sub-millisecond intervals. The 16 MHz instruction cycle and 902-byte RAM enable deterministic scan-list execution while the 5 V supply rails cleanly from a linear regulator on the instrument's analogue front end. Compared with a separate MCU+FPGA the PIC17C reduces BOM cost but lacks the parallelism an FPGA brings to instrument trigger logic; for new designs, a PIC18F67K22 plus low-cost CPLD is the modern equivalent.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC17C766-16/L — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC17C766-16I/L | PIC17C766T-16/L | PIC17C766T-16I/L | PIC17C762-16/PT | PIC17C752-16/L |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 84-PLCC (J-Lead, 29.31x29.31 mm) | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same | 64-TQFP - different | 68-PLCC - different |
| Program Memory Size | 32 KB OTP (16K x 16) | 32 KB OTP | 32 KB OTP | 32 KB OTP | 32 KB OTP | 16 KB OTP (-50%) |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Temperature Grade | Commercial 0 C to +70 C | Industrial -40 C to +85 C | Commercial 0 C to +70 C | Industrial -40 C to +85 C | Industrial -40 C to +85 C | Commercial 0 C to +70 C |
| I/O Pins | 66 | 66 | 66 | 66 | 52 | 54 |
| ADC Channels / Resolution | 16 x 10-bit | 16 x 10-bit | 16 x 10-bit | 16 x 10-bit | 12 x 10-bit | 12 x 10-bit |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | NRND |
اہم امتیازی خصوصیات
- Highest memory density of the PIC17C sub-family (بمقابلہPIC17C752-16/L)
- More ADC channels than the smaller PIC17C devices (بمقابلہPIC17C762-16/PT)
- Industry-standard 84-PLCC footprint for socketed replacement (بمقابلہPIC17C762-16/PT (64-TQFP))
ڈیزائن نوٹس
The PIC17C766-16/L is OTP (one-time programmable); once sealed, the firmware cannot be reprogrammed in-circuit. Design an ICSP header (PGD/PGC/MCLR/VSS/VDD) on every prototype PCB before taping out because a single firmware bug without access to those pads forces board rework. If field updates are a hard requirement migrate to PIC18F8520 instead, which shares the RISC ancestry but provides flash memory.
Provide separate analog (AVDD/AVSS) and digital (VDD1/VDD2/VSS1/VSS2) supply pairs on the 84-PLCC, each decoupled with a 100 nF ceramic plus a 10 uF tantalum at the pin. Long PCB traces between the two VSS planes cause ADC ground bounce; the analog section should reference a star-ground back to a single ferrite bead. Microchip's PIC17C family reference manual shows the canonical 4-pad layout for VDD/VSS and a quiet AVSS.
The 84-PLCC has a J-lead pitch of 1.27 mm (50 mil). On a 2-layer board flood both top and bottom with a ground pour and stitch with 4-6 vias per square inch to control EMI on the high-speed capture/PWM lines. Estimate: at 16 MHz the third harmonic (48 MHz) extends well into HF amateur-radio bands, so add a small ferrite bead on VDD1 and a 33 pF cap on OSC2 if the enclosure lacks shielding.
The PIC17C766-16/L lacks an internal oscillator; OSC1/OSC2 must be driven by an external crystal, ceramic resonator, or CMOS clock source up to 16 MHz. For low-jitter ADC sampling select a crystal with CLoad 18-30 pF (not 32 pF) and configure HS oscillator mode in the configuration word. The reference manual warns that start-up time from power-on can exceed the OST count's default and recommends the LP/HS mode bit selection before code execution proceeds.
تعمیل کی معلومات
Compliance data not surfaced in the Verified Web Data. The PIC17C766 family predates the modern RoHS/REACH declarations common in newer Microchip datasheets; users should consult Microchip's environmental compliance portal for the specific /L package variant.
