S912XET256BVALR - 50MHz 16-Bit 256KB MCU | NXP | Automotive
MPN: S912XET256BVALR ✓ فعالS912XET256BVALR جائزہ
A microcontroller is a programmable embedded-control component that executes firmware, reads sensors, drives actuators, and manages communication interfaces. The S912XET256BVALR belongs to the HCS12X family and combines a 16-bit CPU, on-chip Flash and RAM, analog conversion, timer functions, and communication peripherals in one integrated device. Its 50 MHz operating speed provides a balance between control performance, power consumption, and deterministic response.
Key features include a 12-bit ADC with a stated 3 microsecond conversion time, an XGATE co-processor for offloading selected processing tasks, programmable hardware-emulated EEPROM, memory protection, supervisor and user modes, an enhanced capture timer, a periodic interrupt timer, and a real-time interrupt. These resources support motor, body, powertrain-adjacent, and general vehicle control tasks where predictable interrupt behavior and system integrity matter.
The device is specified for a -40 °C to +105 °C ambient temperature range and an operating supply range shown in the verified distributor data as 1.72 V to 5.5 V. Its 112-LQFP package provides 112 external leads for power, ground, bus, timer, serial, analog, and interrupt functions. Because the package has many pins and mixed peripheral functions, designers should use the official NXP datasheet and reference manual to verify pin multiplexing, alternate functions, decoupling, and board-layout requirements before committing a PCB.
Typical applications include automotive body-control modules, actuator controllers, sensor-interface equipment, industrial embedded controllers, and communication gateways. The 256 KB Flash capacity supports larger embedded applications and boot/update logic, while 16 KB RAM accommodates active control state and peripheral buffers. The 12-bit ADC supports analog sensor acquisition where external conditioning and filtering remain necessary.
Design consideration: validate the power tree, clock configuration, reset behavior, unused-pin treatment, and exact peripheral multiplexing in the NXP documentation. The -40 °C to +105 °C range is useful for harsh environments, but automotive qualification, EMC behavior, transient protection, and production traceability must be evaluated for the complete system rather than inferred from the MCU alone.
This page combines verified distributor specifications, official product-page information, package data, application context, and engineering-oriented comparison notes to help engineers evaluate S912XET256BVALR before schematic capture, PCB layout, sourcing, and qualification.
کے لیے ڈراپ اِن متبادل S912XET256BVALR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں S912XET256BVALR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Core Architecture, Operating Temperature, Pin Count, Mounting Type.
S912XET256J1CALR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →S912XDT256F1VAA
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →S912XES384J2CAL
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →S912XES384J3VAL
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →S912XDT384J1MAG
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →S912XEQ384F1VAL
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
S912XET256BVALR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Product Type | 16-bit HCS12X microcontroller |
| Core | S12X / HCS12X |
| Maximum CPU Frequency | 50 MHz |
| Flash Memory | 256 KB |
| RAM | 16 KB |
| ADC Resolution | 12 bit |
| ADC Conversion Time | 3 microseconds |
| آپریٹنگ سپلائی وولٹیج | 1.72 V to 5.5 V |
| آپریٹنگ درجہ حرارت | -40 °C to +105 °C |
| پیکیج | 112-LQFP, 20 x 20 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| XGATE Co-processor | Present |
| Programmable EEPROM Emulation | Supported |
| Memory Protection Unit | Supported |
| Timer Resources | Enhanced capture timer, periodic interrupt timer, and real-time interrupt |
| External Flash | 91, as listed in distributor technical data |
| RoHS | Compliant |
S912XET256BVALR 112-lqfp, 20 x 20 mm پن کنفیگریشن گائیڈ
S912XET256BVALR (112-lqfp, 20 x 20 mm پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں S912XET256BVALR.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
S912XET256BVALR کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive Body-Control Module, Vehicle Sensor Interface, Motor and Actuator Controller, Industrial Embedded Controller, Automotive Communication Gateway, Programmable Logic and Timing Controller.
Automotive Body-Control Module
The S912XET256BVALR fits body-control modules that combine switch inputs, sensor conditioning, actuator outputs, and diagnostic communication. Its 50 MHz 16-bit S12X core provides deterministic control processing, while 256 KB Flash gives application firmware, diagnostic logic, and communication stacks practical memory headroom. The automotive-qualified identity and -40 °C to +105 °C rating are relevant for cabin and vehicle electronics, although the finished module must still pass its own EMC and environmental validation. The real-time interrupt and periodic interrupt timer support periodic tasks, and the 12-bit ADC supports acquisition from conditioned analog sensors.
تجویز کردہ
Vehicle Sensor Interface
Use the S912XET256BVALR as the central controller for a 12-bit analog sensor interface when the system needs local conversion, filtering, and control in a 1.72 V to 5.5 V embedded environment. The verified ADC conversion time is 3 microseconds, allowing periodic sampling when the overall loop and acquisition sequence are designed correctly. The S12X CPU can handle calibration, threshold logic, diagnostics, and communication framing. Since the MCU is not a complete analog front end, input protection, filtering, reference design, grounding, and calibration still require careful implementation.
تجویز کردہ
Motor and Actuator Controller
The S912XET256BVALR is suitable for small automotive actuator controllers where deterministic pulse timing, sensor feedback, and protective logic are required. The enhanced capture timer can measure input edges, the periodic interrupt timer can schedule control updates, and the 16-bit S12X core can execute position, speed, or state-machine logic. Its 50 MHz clock provides processing margin, but the designer must budget CPU time for diagnostics and communications. Power-stage drivers, current sensing, protection networks, and thermal management remain external to the MCU and must be validated as part of the motor-control subsystem.
تجویز کردہ
Industrial Embedded Controller
The S912XET256BVALR can serve in industrial equipment where deterministic control, local I/O, analog acquisition, and moderate firmware complexity are more important than a high-end application processor. Its 256 KB Flash and 16 KB RAM provide room for control routines, parameter storage, diagnostics, and communication protocols. The -40 °C to +105 °C range supports environments beyond typical room-temperature consumer conditions, but the enclosure, heater, thermal design, and power supply determine whether the system can maintain the MCU within its limits. Memory protection and supervisor/user modes can improve software isolation when firmware partitioning is required.
تجویز کردہ
Automotive Communication Gateway
The S912XET256BVALR is a possible fit for a low-level gateway that gathers switch or sensor information, performs local logic, and forwards messages over one or more automotive communication interfaces. Its 16-bit architecture and 50 MHz operating point are useful for protocol handling and deterministic task scheduling, while 256 KB Flash can hold gateway firmware and configuration logic. The verified data does not enumerate the complete communication peripheral set, so interface selection must be checked in the official datasheet. Termination, protection, transient immunity, bus diagnostics, and network sleep behavior are system-level requirements.
تجویز کردہ
Programmable Logic and Timing Controller
The S912XET256BVALR can implement programmable sequencing and timing functions using its real-time interrupt, periodic interrupt timer, and enhanced capture timer. This makes it useful in embedded systems that must coordinate switch debouncing, sampling windows, actuator timing, or fault-response sequences with predictable interrupt behavior. The 12-bit ADC can monitor analog conditions when the control task requires feedback beyond digital timing. Firmware structure, interrupt priorities, clock setup, and memory mapping should be reviewed carefully because timer resources share a finite bus and execution budget with other peripherals.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا S912XET256BVALR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | S912XET256J1CALR | S912XDT256F1VAA | S912XES384J2CAL | S912XES384J3VAL | S912XDT384J1MAG |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 112-LQFP (20x20) | 112-LQFP (20x20) - package class indicated | 112-LQFP (20x20) - package class indicated | 112-LQFP (20x20) - package class indicated | 112-LQFP (20x20) - package class indicated | 112-LQFP (20x20) - package class indicated |
اہم امتیازی خصوصیات
- Verified automotive-oriented feature set (بمقابلہS912XDT256F1VAA)
- 50 MHz S12X control performance (بمقابلہS912XET256J1CALR)
- Integrated real-time and memory-integrity resources (بمقابلہS912XES384J3VAL)
- 12-bit analog conversion capability (بمقابلہS912XDT384J1MAG)
ڈیزائن نوٹس
Treat the 112-LQFP as a high-pin-count mixed-signal and embedded-control footprint. Place the required bypass capacitors close to the MCU power pins, route supply and ground planes without uncontrolled splits, and keep analog inputs away from switching nodes and high-current return paths. Verify every pin's alternate function in the NXP datasheet before assigning a net because many MCU functions can be multiplexed.
Validate the 1.72 V to 5.5 V supply range against the actual rail used in the product, including regulator tolerance, startup behavior, transient limits, and peripheral current. The verified data does not state operating current, so do not calculate power budgets from an assumed value. Review the electrical characteristics for each clock mode, peripheral state, temperature, and voltage before finalizing the power supply.
Reserve clean return paths for the 12-bit ADC and its reference network. Place input filtering and protection close to the source or connector, maintain controlled analog routing, and separate ADC traces from clock, PWM, and high-current actuator outputs. The stated 3 microsecond conversion time is a device-level value; total measurement accuracy also depends on acquisition time, source impedance, reference quality, calibration, and firmware processing.
Do not substitute a related S912X family part solely because it has a 112-LQFP package and similar memory capacity. Verify pin names, alternate functions, memory map, clock limits, peripheral set, supply levels, temperature grade, and software device definition. A package match alone does not guarantee drop-in replacement, and the supplied cross-reference data does not provide a manufacturer-confirmed substitute.
تعمیل کی معلومات
The verified NXP product listing identifies S912XET256BVAL as automotive qualified, and the distributor listing identifies RoHS compliance. REACH, lead-free status, halogen-free status, and conflict-minerals status are not provided and remain unknown.
