TLV2633ID - Dual 9 MHz RRIO Op Amp | Texas Instruments
MPN: TLV2633ID ✓ فعالTLV2633ID جائزہ
An operational amplifier is an analog signal-processing IC that uses differential feedback to amplify the difference between two input voltages. A rail-to-rail input and output stage can operate near the supply rails, making the TLV2633ID useful for sensor signals, battery-powered instrumentation, audio paths, and low-voltage control systems. In the device hierarchy, it is an operational amplifier, analog amplifier, and linear integrated circuit.
The two amplifiers can handle independent signals or work together in differential, filtering, buffering, and gain configurations. Their 9 MHz gain-bandwidth product supports higher-frequency signal paths than low-bandwidth precision amplifiers while retaining the low approximately 1 mA-per-channel supply-current characteristic emphasized by the family description. Shutdown support can reduce activity when a subsystem is not needed, although individual shutdown behavior and control logic must be confirmed in the manufacturer datasheet before final design release.
The wide-bandwidth, low-power architecture makes the TLV2633ID appropriate for general-purpose analog conditioning rather than only precision DC measurement. Its rail-to-rail characteristics simplify signal acquisition from sensors whose operating range approaches the available supply voltage. Two amplifiers in one package also reduce board area compared with two separate single-amplifier devices, while dual independent channels provide flexibility for signal conditioning or active filtering.
Typical uses include portable sensor interfaces, buffered sensor outputs, low-voltage audio stages, analog monitoring channels, general-purpose active filters, and embedded control systems. The device can also support dual-amplifier topologies when common supply routing and shared decoupling are advantageous. Selection should account for the required common-mode range, output swing, noise, offset, stability, and load capability at the actual supply voltage.
For layout, place the bypass capacitor close to the supply pins and maintain a common ground reference across both channels. Decoupling resistance and capacitance should be evaluated against the desired gain, source impedance, and signal bandwidth. Input and output nodes should be kept compact and separated where appropriate, especially when low-level signals are amplified.
This page organizes the available technical characteristics, packaging details, application guidance, and verified source references for faster engineering review. It also distinguishes confirmed ratings from parameters that require direct confirmation in the manufacturer datasheet, helping designers establish whether the TLV2633ID fits a specific low-voltage analog circuit.
کے لیے ڈراپ اِن متبادل TLV2633ID — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںTLV2633ID زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Number of Circuits | 2 circuits |
| Rail-to-Rail Operation | Rail-to-rail input and output |
| Supply Current per Channel | 1 mA |
| Gain-Bandwidth Product | 9 MHz |
| Supply Type | Single supply |
| Shutdown Capability | Supported |
| Power Class | Low power |
| Signal Bandwidth Class | Wide bandwidth |
| پیکیج | 14-pin SOIC |
| RoHS اسٹیٹس | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
TLV2633ID 14-pin soic پن کنفیگریشن گائیڈ
TLV2633ID (14-pin soic پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TLV2633ID.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
TLV2633ID کے لیے موزوں ہے 6 ایپلیکیشنs: Portable Sensor Signal Conditioning, Low-Voltage Audio Signal Path, Dual Active Filter, Battery-Powered Monitoring System, Industrial Control Interface, General-Purpose Buffered Interface.
Portable Sensor Signal Conditioning
The TLV2633ID fits portable sensing systems where two low-power amplifier channels must condition signals from sensors operating near the available supply rail. Rail-to-rail inputs and outputs reduce the need to restrict sensor excitation to a narrower mid-supply range, while approximately 1 mA supply current per channel supports battery-conscious designs. The 9 MHz gain-bandwidth product provides useful bandwidth for sensor signals beyond low-frequency DC measurement. One channel can amplify or filter a sensor output while the second handles a reference, auxiliary signal, or second sensing path. Confirm the input common-mode limits and output swing at the selected supply voltage, and verify offset, noise, and stability against the required sensor accuracy.
Low-Voltage Audio Signal Path
The TLV2633ID can support low-voltage audio and communication signal paths because it combines rail-to-rail operation, a 9 MHz gain-bandwidth product, and a dual-amplifier configuration. The two independent channels can implement a non-inverting or inverting preamplifier, an active filter, or a line-driver stage while sharing package and supply connections. The approximately 1 mA-per-channel supply current helps limit consumption in portable audio equipment. Because small-signal audio designs are sensitive to noise, distortion, output swing, and stability, engineers should confirm voltage-noise density, slew rate, output-current capability, and output-voltage headroom for the actual load before finalizing the gain and filter values.
Dual Active Filter
Both amplifier channels in the TLV2633ID can form an active-filter section for low-voltage analog conditioning. A 9 MHz gain-bandwidth product is appropriate for signal bands extending beyond audio frequencies, while approximately 1 mA supply current per channel helps control overall system demand. The filter topology determines the relationship between gain, bandwidth, component tolerances, and maximum operating frequency. Designers should calculate the closed-loop response using the op-amp gain-bandwidth, slew-rate, output-capacitance, and noise characteristics in the manufacturer documentation. Feedback-component placement is important because parasitic capacitance near a high-impedance input can alter the intended response or reduce stability.
Battery-Powered Monitoring System
The TLV2633ID is useful in battery-powered monitoring equipment that needs two general-purpose analog channels without the power burden of higher-current amplifiers. Its approximately 1 mA supply current per channel is particularly relevant when continuous operation dominates the power budget, and rail-to-rail behavior helps process sensor or supervisory signals near the supply limits. The shutdown function can also support power-management strategies where the measured channel does not need to remain active continuously. Determine whether shutdown affects only one channel or the common device state, and verify wake-up behavior directly from the manufacturer documentation. Confirm the actual input bias current, offset, and leakage against the high-impedance source because low power alone does not guarantee low measurement error.
Industrial Control Interface
The dual TLV2633ID can process two low-level control signals in industrial equipment while providing a compact 14-pin SOIC implementation. The 9 MHz gain-bandwidth product is sufficient for many sensor, threshold, and buffered-control tasks, while the approximately 1 mA-per-channel supply current can simplify thermal and battery budgets in distributed nodes. One channel may buffer a sensor input and the other may provide an amplified control signal or active filtering. Industrial design work should verify operating-temperature limits, supply tolerances, transient protection, common-mode range, and electromagnetic robustness because the family description does not establish those ratings. Place supply bypassing at the package and route high-impedance input traces away from switching nodes to reduce coupled noise.
General-Purpose Buffered Interface
The TLV2633ID can buffer two input signals when a source requires a low-impedance drive for a downstream ADC, comparator, or digital control input. Rail-to-rail output behavior preserves much of the available signal range, and the 9 MHz gain-bandwidth product is more than adequate for many moderate-bandwidth acquisition paths. Using a unity-gain buffer configuration simplifies gain planning, but the selected configuration should still be checked for stability with the source impedance and load capacitance. Confirm output-current capability, capacitive-load stability, and output-voltage limits for the attached circuit. Keeping both channels on the same package also makes it convenient to buffer complementary or related signals while maintaining a common return path and decoupling strategy.
کے لیے انجینئرنگ ریفرنس ڈیٹا TLV2633ID — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Package | 14-pin SOIC |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Rail-to-Rail Operation | Rail-to-rail input and output |
| Supply Current per Channel | 1 mA |
| Gain-Bandwidth Product | 9 MHz |
| Supply Type | Single supply |
| Shutdown Capability | Supported |
اہم امتیازی خصوصیات
- Two amplifiers with rail-to-rail signal handling in one package (بمقابلہOPA234EA)
- Low-power dual-channel integration (بمقابلہOPA234EA)
- Wide-bandwidth general-purpose signal conditioning (بمقابلہOPA234EA)
ڈیزائن نوٹس
Place the supply bypass capacitor adjacent to the power and ground pins, with a short and low-inductance return path. Because the TLV2633ID contains two amplifier channels in one 14-pin SOIC, follow the manufacturer pinout when assigning both channel inputs, outputs, and shutdown control. Keep sensitive input and feedback traces short, avoid routing them alongside switching-node or high-current traces, and use a continuous ground reference where practical.
Do not assume that rail-to-rail operation permits inputs or outputs to reach the supply rails under every condition. Check the manufacturer electrical-characteristics curves for the selected supply voltage, output-load current, input bias current, and temperature. When driving a capacitive load, verify capacitive-load stability, and when using a feedback network, account for the source impedance and parasitic capacitance that can alter the intended gain or response.
Use the approximately 1 mA-per-channel characteristic as the starting point for a low-power budget, then add load current, shutdown-state behavior, regulator overhead, and the current required by surrounding circuitry. Confirm whether the shutdown control applies to both channels or one channel before designing a power-gating sequence. Keep the bypass capacitor close to the package so switching-current transients do not create voltage excursions on the sensitive analog supply rail.
تعمیل کی معلومات
No explicit environmental, automotive, or material-compliance declarations were identified for the exact TLV2633ID ordering code.