USB2422I-CP-TR - 2-Port USB 2.0 Hub Controller, 24-QFN | Microchip
MPN: USB2422I-CP-TR ✓ فعالUSB2422I-CP-TR جائزہ
A USB hub controller is a semiconductor that manages traffic between one upstream USB host port and multiple downstream device ports. In the USB hierarchy it sits below a USB host controller, above USB peripherals, and inside the wider class of interface ICs. Unlike a host controller that enumerates the whole bus, a hub controller segments a single USB segment into multiple ports, adding tiered topology, port over-current detection and per-port power management to embedded designs.
The USB2422 uses a single transaction translator architecture, which keeps die area and system cost low for embedded hubs. All USB port resistors are integrated: every required series termination resistor on the D+ and D- pins, all required pull-down and pull-up resistors on D+ and D-, and internal pull-up resistors on the downstream-facing over-current sense inputs. That integration removes external discrete networks from the USB port layout.
The controller attaches upstream as a Hi-Speed and Full-Speed hub or as a Full-Speed-only hub, giving the designer a path to reuse one PCB across both high-speed and legacy USB peripherals. Downstream port support covers Low-Speed, Full-Speed and Hi-Speed devices, so keyboards, mass storage, HID and composite peripherals can coexist behind the hub. The SMBus 1.0 specification voltage, power and timing characteristics are met for slave-only devices, with the noted exceptions documented in the datasheet.
Typical embedded uses include industrial HMI panels, medical instrument consoles, set-top and smart-home gateways, USB-to-serial and USB-to-Ethernet bridges, and multi-port charging and docking stations. The 24-QFN package with a compact 4 x 4 mm footprint supports dense board layouts where connector count is constrained.
One key design consideration is port power budgeting: each downstream port must source current per the USB specification, so the board supply and any port-current switches must be sized for the worst case of all ports loaded simultaneously, not the nominal single-device case.
This page combines the manufacturer hub controller description, package and feature data with practical port-resistor, thermal and layout guidance, drop-in alternatives and a parameter comparison that is not consolidated in a single manufacturer document.
کے لیے ڈراپ اِن متبادل USB2422I-CP-TR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں USB2422I-CP-TR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Product Type, Number of Downstream Ports, Package Type, Supported Downstream Speeds.
USB2422-CP-TR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →USB2412-DZK-TR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →USB2227-NU-05
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →USB2005-MV-01
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →USB2422I/CH
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
USB2422I-CP-TR تفصیلات
| Device Type | USB 2.0 hub controller with 2 downstream ports |
| USB Specification | USB 2.0 |
| Number of Downstream Ports | 2 |
| Upstream Port Modes | Hi-Speed and Full-Speed hub, or Full-Speed-only hub |
| Supported Downstream Speeds | Low-Speed, Full-Speed, Hi-Speed |
| Architecture | Single transaction translator |
| پیکیج | 24-pin QFN (4 x 4 mm) |
| Series Termination Resistors | Integrated on all D+ and D- pins |
| Pull-Up / Pull-Down Resistors | All required USB pull-up and pull-down resistors integrated |
| Over-Current Sense Inputs | Internal pull-up resistors on downstream-facing ports |
| SMBus Compliance | SMBus 1.0 voltage, power and timing characteristics for slave-only devices |
| Number of I/O Pins | 24 |
USB2422I-CP-TR 24-pin qfn (4 x 4 mm) پن کنفیگریشن گائیڈ
USB2422I-CP-TR (24-pin qfn (4 x 4 mm) پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں USB2422I-CP-TR.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
USB2422I-CP-TR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial HMI Panel USB Hub, Medical Instrument Console, USB-to-Serial and USB-to-Ethernet Bridge, Docking Station and Multi-Port Charging Hub, Set-Top Box and Smart-Home Gateway, Portable Test and Measurement Instrument.
Industrial HMI Panel USB Hub
The USB2422I-CP-TR adds two downstream USB 2.0 ports to an industrial human-machine interface without adding a discrete hub chipset footprint. Because the device can attach upstream as a Hi-Speed and Full-Speed hub or as a Full-Speed-only hub, a single board can serve legacy barcode scanners and keyboards alongside high-bandwidth data loggers. All series termination resistors on the D+ and D- pins, plus the required pull-up and pull-down resistors, are integrated into the hub, so the PCB around each connector stays free of discrete resistor networks. In an industrial enclosure where temperature excursions are common, the industrial-grade -I ordering option of the 24-QFN part keeps the hub within its rated operating limits.
تجویز کردہ
Medical Instrument Console
Diagnostic and patient-monitoring consoles typically need to accept several USB peripherals such as keyboards, touch panels and storage media from a single host port. The USB2422I-CP-TR provides two downstream ports in a compact 24-QFN footprint, which preserves board area for analog front ends. Downstream support for Low-Speed, Full-Speed and Hi-Speed devices allows HID, mass storage and composite peripherals to coexist behind the hub, and the hub's SMBus 1.0 conformance for slave-only devices supports connected equipment that monitors the bus. Because every required USB pull-up and pull-down resistor is on-chip, connector routing stays short and the layout contains fewer components to qualify for medical equipment.
تجویز کردہ
USB-to-Serial and USB-to-Ethernet Bridge
Legacy serial ports and isolated Ethernet links are often exposed over USB in embedded gateways. The USB2422I-CP-TR acts as the two-port USB 2.0 hub that feeds these bridges from a single upstream connection, and the option to run as a Full-Speed-only hub simplifies firmware when only low-bandwidth CDC or HID bridges are attached. The single transaction translator architecture keeps the silicon and power budget small compared with a multi-port hub chipset, and the integrated D+ and D- termination resistors mean the bridge boards need no external resistor networks. The 4 x 4 mm 24-QFN outline leaves room for the bridge's isolation and magnetics in the same enclosure.
تجویز کردہ
Docking Station and Multi-Port Charging Hub
Docking stations and desk-top charging hubs need to expose several USB ports from one host port while keeping board area and cost low. The USB2422I-CP-TR delivers two downstream ports with the D+ and D- termination, pull-up and pull-down resistors already integrated, so the connector section of the board is dominated by the receptacles and the port power path. The downstream over-current sense inputs have internal pull-ups, which simplifies the connection to port power switches and lets a system monitor fault conditions on each port. In a charging hub the hub controller handles enumeration and transaction translation while the port power switches handle current, keeping the USB data path compliant without an external hub chipset.
تجویز کردہ
Set-Top Box and Smart-Home Gateway
Set-top and smart-home gateway designs often expose a USB port for storage, keyboards or a local update stick, while the internal system also needs a hub for diagnostic access. The USB2422I-CP-TR provides that two-port USB 2.0 hub in a 24-QFN package with all port resistors integrated, which keeps the BOM small for cost-sensitive consumer gateways. Low-Speed, Full-Speed and Hi-Speed downstream support means a HID remote, a USB stick and a network adapter can all attach behind the same controller. The choice between Hi-Speed plus Full-Speed upstream mode and Full-Speed-only mode lets the firmware trade throughput for simpler behaviour when only low-speed accessories are present.
تجویز کردہ
Portable Test and Measurement Instrument
Portable analyzers and bench instruments need USB connectivity for data logging and PC control, often through a single connector on a crowded front panel. The USB2422I-CP-TR adds two downstream ports in a compact 4 x 4 mm 24-QFN footprint that can sit behind the instrument's existing upstream port, expanding a one-port design into a two-port hub without a separate hub module. With the required series termination and bias resistors integrated, USB routing between the controller and the connectors is short and repeatable, which helps keep eye-diagram margins consistent across production units. The industrial-grade option suits instruments used in field service environments with wide ambient temperature variation.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا USB2422I-CP-TR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | USB2422-CP-TR | USB2412-DZK-TR | USB2227-NU-05 | USB2005-MV-01 | USB2422I/CH |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | QFN-24 (4 x 4 mm) | QFN-24 (4 x 4 mm) - same | QFN-24 (4 x 4 mm) - same | QFN-24 (4 x 4 mm) - same | QFN-24 (4 x 4 mm) - same | QFN-24 (4 x 4 mm) - same |
| Device Type | USB 2.0 hub controller, 2 downstream ports | USB 2.0 hub controller, 2 downstream ports | USB 2.0 hub controller, 2 downstream ports | USB 2.0 hub controller, 2 downstream ports | USB 2.0 hub controller, 4 downstream ports | USB 2.0 hub controller, 2 downstream ports |
اہم امتیازی خصوصیات
- Full USB port resistor integration reduces external discrete count (بمقابلہUSB2412-DZK-TR)
- Configurable upstream mode supports Hi-Speed plus Full-Speed or Full-Speed-only (بمقابلہUSB2227-NU-05)
- Industrial temperature grade in a 4 x 4 mm QFN-24 footprint (بمقابلہUSB2422-CP-TR)
- Two downstream ports instead of four for smaller dock designs (بمقابلہUSB2005-MV-01)
ڈیزائن نوٹس
Route D+ and D- as a tightly coupled, length-matched pair directly from the USB2422I-CP-TR pins to the downstream connectors, keeping the traces short and over a continuous ground plane. Because all series termination resistors and the required pull-up and pull-down resistors are integrated on-chip, do not add discrete terminations at the connectors, and avoid stubs or test pads on the data nets. A clean point-to-point USB 2.0 path is what allows the hub to operate reliably at Hi-Speed.
Estimated: with two downstream ports at the USB 2.0 maximum bus draw of 500 mA per port and 5 V, the hub data path can require about 1 A of downstream current. The USB2422I-CP-TR itself is specified as a low-power controller, but the board supply, port power switches and any upstream current-limiting device must be sized for the worst case where both ports load simultaneously. Do not rely on the nominal single-device case when selecting the upstream regulator or protection FET.
The commonest mistake in USB2422 designs is adding external 15 kohm pull-ups or 22 ohm series resistors on the D+ and D- lines, because those networks are already integrated inside the hub controller. A second frequent error is treating the downstream over-current sense inputs as plain logic inputs; they already carry internal pull-ups and are intended to be wired to port power switch fault outputs, so the reference design in the data sheet should be followed exactly for over-current detection.
The 24-QFN package has a limited exposed-pad area, so place the USB2422I-CP-TR over a solid ground pour and connect the exposed pad to ground with a full array of vias. In an enclosed instrument where the hub sits next to a switching supply or a linear regulator dissipating several watts, add thermal relief around the pad and keep the USB data traces away from heat sources, since controller junction temperature rise translates directly into the industrial temperature margin you paid for with the -I grade.
تعمیل کی معلومات
The USB2422 data sheet (document 00001726B) covers SMBus 1.0 conformance for slave-only devices and USB 2.0 hub operation. RoHS, REACH, halogen-free and conflict-minerals statements were not present in the available documentation and must be confirmed with the manufacturer before release.
