Vi điều khiển

Sản phẩm (20.000+)

MC908AP32ACBE - 8-bit HC08 MCU 32KB Flash 8MHz | NXP
MC908AP32ACBE

MC908AP32ACBE - 8-bit HC08 MCU 32KB Flash 8MHz | NXP

The NXP Semiconductors MC908AP32ACBE is an 8-bit microcontroller unit (MCU) from the HC08 family with 32KB of FLASH program memory, an 8MHz internal high-speed oscillator, and a 42-pin SDIP (0.600 inch, 15.24mm) through-hole package operating from a 4.5V to 5.5V supply. An 8-bit microcontroller is an integrated circuit that combines a processor core, memory, and peripherals on a single chip, executing instructions on 8-bit data words. Within the power-management and control hierarchy, an MCU sits above discrete logic and below 32-bit application processors, making it the workhorse for embedded control systems. The HC08 family from Motorola/Freescale (now NXP) is a legacy architecture descended from the popular 6805 core, widely used in appliance, automotive, and industrial designs throughout the 1990s and 2000s. Key features of the MC908AP32ACBE include 32KB (32K x 8) of in-circuit-programmable FLASH program memory, 2KB (2K x 8) of RAM, and an internal oscillator rated for 8MHz bus operation, which eliminates the need for an external crystal in many designs. The device provides 30 general-purpose I/O lines, giving ample connectivity for switches, relays, displays, and serial peripherals in through-hole systems. Architecturally, the part is based on the enhanced M68HC08 CPU core with a von Neumann memory map, stack pointer-based C-friendly programming model, and a low-power WAIT and STOP mode set. The internal high-speed oscillator (HS OSC) simplifies clocking, while FLASH non-volatility allows field firmware updates. Because it is a mature HC08 device, mature development toolchains and third-party programmers remain available from legacy-support channels. Typical applications include white-goods appliance control boards, industrial sensor and actuator controllers, automotive body-electronics sub-modules, battery chargers, and legacy-equipment maintenance where a through-hole 42-pin SDIP footprint must be preserved. The 5V supply range makes it directly compatible with legacy 5V industrial logic families. A key design consideration is availability: this is a mature product primarily supplied through aftermarket and authorized excess channels such as Rochester Electronics, so new designs should evaluate the newer S08 family. Verify exact peripheral configuration (timers, ADC, SCI) against the manufacturer datasheet before design reuse. This page synthesizes distributor listings, cross-reference guidance, and lifecycle notes for the MC908AP32ACBE that are not consolidated in any single manufacturer document, helping engineers secure obsolete inventory or identify drop-in same-family alternatives.

RFQ Liên hệ
MC908AP32ACFBE - 8-Bit 8MHz 32KB Flash MCU | NXP
MC908AP32ACFBE

MC908AP32ACFBE - 8-Bit 8MHz 32KB Flash MCU | NXP

NXP Semiconductors MC908AP32ACFBE is an 8-bit HC08 microcontroller with a CPU08 core, 8 MHz operation, 32 KB of Flash program memory, and a 44-QFP package measuring 10 x 10 mm. The device belongs to the HC08AP high-speed-oscillator family within the M68HC08 product hierarchy. Verified distributor data identifies a -40 °C to +85 °C industrial temperature range and an operating supply range of 4.5 V to 5.5 V. NXP currently labels the product end of life, so procurement planning must account for limited future availability rather than assuming a long active lifecycle. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, digital I/O, and peripherals into one device. The 8-bit MCU category is suited to compact control systems that evaluate logic and operate sensors, actuators, communication interfaces, or human-machine interfaces. Within the broader hierarchy, the MC908AP32ACFBE is an MCU, then a semiconductor, and ultimately an embedded-control component used to execute firmware and coordinate real-time system behavior. The verified feature set identifies 32 KB of Flash memory, 8 MHz clock capability, and 32 I/O ports. Flash retains program code when power is removed, allowing firmware updates and persistent configuration, while the 32 digital I/O pins provide connections for switches, indicators, sensors, and external control logic. The high-speed-oscillator HC08APxA version is distinguished from the related HC08AP family by its oscillator configuration, but detailed peripheral assignments and electrical limits were not included in the supplied source material. Architecture is centered on the enhanced M68HC08 CPU08 core. An 8-bit processor processes one byte per machine-data path and is typically used where deterministic control, modest arithmetic demands, and low system complexity matter more than high computational throughput. The verified 8 MHz operating point supports general-purpose embedded tasks, although real firmware performance depends on instruction mix, memory behavior, peripherals, and interrupt load. Typical uses include compact industrial controllers, appliance interfaces, motor-sequence controls, instrumentation, and small communication modules. For a new design, the NXP end-of-life status should trigger review of the NXP replacement program, last-time-buy timing, and firmware compatibility. Existing production equipment may continue using MC908AP32ACFBE if its 44-QFP footprint and software environment remain unchanged, but a redesign should compare any suggested replacement for memory, peripherals, pinout, voltage, timing, and toolchain compatibility. Layout must preserve the exact 44-QFP land pattern and route decoupling and clock inputs according to the manufacturer data. Because the supplied data does not include a verified pin table, designers must obtain the official package drawing before assigning signals; analogous-looking HC08 devices must not be assumed interchangeable. This page combines verified lifecycle, memory, clock, package, temperature, commercial, and cross-reference information with explicit engineering caveats. It is designed to support sourcing decisions while avoiding unsupported assumptions about electrical limits, pin functions, peripherals, or unverified replacement devices.

RFQ Liên hệ
MC908AP32CBE - 8-Bit HC08 MCU 32KB Flash 8MHz 42-PDIP | NXP
MC908AP32CBE

MC908AP32CBE - 8-Bit HC08 MCU 32KB Flash 8MHz 42-PDIP | NXP

The NXP MC908AP32CBE is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units, integrating 32KB of on-chip Flash program memory, 2KB of RAM, and a 10-bit ADC in a 42-pin PDIP (0.600 inch, 15.24 mm) through-hole package. The device runs at an internal bus speed of 8 MHz and is supported by a CISC instruction set optimized for embedded control code density. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash or ROM), volatile working memory (RAM), and a range of integrated peripherals such as ADC, timers, communication interfaces, and general-purpose I/O. Within the broader semiconductor taxonomy, the MC908AP32CBE sits at: microcontroller -> 8-bit MCU -> HC08 family -> Flash-based MCU -> mixed-signal embedded controller. The HC08 architecture succeeds the earlier HC05 core with improved addressing modes, higher code density, and an enhanced instruction set designed for C compilers and structured assembly. Key features of the MC908AP32CBE include 30 general-purpose I/O lines, an internal oscillator that eliminates external clock components, a 10-bit analog-to-digital converter for sensor interfacing, and Flash memory that supports in-application reprogramming via a background debug mode. The 42-pin PDIP package is intended for development, prototyping, and through-hole industrial designs where socketed replacement or hand rework is desirable. Technically, the MC908AP32CBE uses a Freescale/NXP-developed CISC core with a 16-bit stack pointer and an enhanced HC08 instruction set. The integrated peripherals are memory-mapped and accessed through a uniform bus architecture, simplifying firmware bring-up. Internal Flash supports in-circuit programming, enabling field firmware updates without removing the device from the application board. Typical applications include industrial control modules, appliance controllers, automotive body electronics, HVAC thermostats, sensor signal conditioning front-ends, and consumer white-goods main boards. Designers value the HC08 family for its deterministic interrupt latency, mature toolchain support (CodeWarrior, Cosmic, IAR), and a wide portfolio of derivatives that share peripheral and instruction-set compatibility. When designing with the MC908AP32CBE, ensure the supply rails (3.3 V or 5 V operation) and decoupling network follow the manufacturer reference design. The internal oscillator should be validated against timing-critical peripherals such as UART, and an external crystal may be substituted if greater frequency accuracy is required for asynchronous communications. This page synthesizes distributor pricing, datasheet cross-references, and engineering application guidance not found in the manufacturer datasheet alone, providing a single decision-ready view for embedded engineers selecting an 8-bit MCU for through-hole designs.

RFQ Liên hệ
MC908AP32CFAE - 8MHz 8-bit HC08 MCU 32KB Flash 48-LQFP | NXP
MC908AP32CFAE

MC908AP32CFAE - 8MHz 8-bit HC08 MCU 32KB Flash 48-LQFP | NXP

The NXP MC908AP32CFAE is an 8-bit HC08-family microcontroller with 32KB of on-chip Flash program memory, 2KB of RAM, and a 10-bit ADC, housed in a 48-pin LQFP (7x7 mm) package. It executes instructions from an enhanced M68HC08 CPU08 core at up to 8MHz and supports dual-voltage operation at 3.3V or 5V for flexible system integration. The part is specified across an industrial temperature range and exposes 32 general-purpose I/O lines for peripheral interfacing. An 8-bit microcontroller (MCU) is a small, self-contained processor-on-a-chip that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a fixed set of peripherals such as timers, communication controllers, and analog-to-digital converters. Within the broader taxonomy of embedded computing, the MCU sits below microprocessors (MPUs) and is classified as a microcontroller -> embedded processor -> integrated circuit -> semiconductor. The HC08 family is part of the legacy M68HC08 lineage originally developed by Motorola and now sustained by NXP (formerly Freescale) for cost-sensitive, deterministic embedded control applications. Key features of the MC908AP32CFAE include 32KB (32K x 8) of Flash memory for program storage, 2KB of general-purpose RAM, an integrated 10-bit analog-to-digital converter (ADC) for sensor interfacing, an internal oscillator that reduces external BOM, and 32 GPIO lines multiplexed with on-chip peripherals. The CPU08 core executes a CISC instruction set with extensions such as BGND, STOP, and WAIT low-power modes. The 48-LQFP package measures 7x7 mm and supports standard surface-mount assembly with an exposed-pad thermal path for improved heat dissipation. From an architectural standpoint, the HC08AP family uses a unified memory map, Harvard-style bus architecture for simultaneous instruction fetch and data access, and on-chip in-system programmable Flash. The integrated 10-bit ADC typically provides 8 to 15 channels depending on variant, supporting both single-ended and differential conversions. Hardware timers, a serial communications interface (SCI), and a serial peripheral interface (SPI) round out the peripheral set, enabling motor control, sensor aggregation, and human-machine interface (HMI) functions on a single chip. Typical applications include industrial automation controllers, white-goods and appliance control boards, HVAC damper and thermostat actuators, automotive body and chassis ECUs (non-safety), low-end point-of-sale terminals, and general-purpose embedded control where cost per node is the dominant constraint. Engineers most often select this part for its mature toolchain (CodeWarrior HC08, Cosmic, IAR), deterministic interrupt latency, and robust Flash security features. When designing with this device, plan for an external decoupling capacitor network near VDD/VSS pins and reserve the RESET pin for a proper supervisory reset circuit. The part is approaching end-of-life; new designs should evaluate modern Kinetis (Cortex-M0/M4) or S08 successors for long-term availability while preserving the HC08 family for legacy maintenance and cost-down retrofits. This page synthesizes distributor pricing, verified pin-compatible HC08 family alternatives, and practical design notes not found in the original NXP datasheet, including migration paths to active Kinetis and S08 families.

RFQ Liên hệ
MC908AP32CFAER - 8MHz 8-bit HC08 MCU 32KB Flash 48-LQFP | NXP (Tape & Reel)
MC908AP32CFAER

MC908AP32CFAER - 8MHz 8-bit HC08 MCU 32KB Flash 48-LQFP | NXP (Tape & Reel)

The NXP MC908AP32CFAER is an 8-bit HC08-family microcontroller with 32KB of on-chip Flash program memory, 2KB of RAM, and a 10-bit ADC, housed in a 48-pin LQFP (7x7 mm) package. It executes instructions from an enhanced M68HC08 CPU08 core at up to 8MHz and supports dual-voltage operation at 3.3V or 5V for flexible system integration. The part is specified across an industrial temperature range and exposes 32 general-purpose I/O lines for peripheral interfacing. An 8-bit microcontroller (MCU) is a small, self-contained processor-on-a-chip that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a fixed set of peripherals such as timers, communication controllers, and analog-to-digital converters. Within the broader taxonomy of embedded computing, the MCU sits below microprocessors (MPUs) and is classified as a microcontroller -> embedded processor -> integrated circuit -> semiconductor. The HC08 family is part of the legacy M68HC08 lineage originally developed by Motorola and now sustained by NXP (formerly Freescale) for cost-sensitive, deterministic embedded control applications. Key features of the MC908AP32CFAER include 32KB (32K x 8) of Flash memory for program storage, 2KB of general-purpose RAM, an integrated 10-bit analog-to-digital converter (ADC) for sensor interfacing, an internal oscillator that reduces external BOM, and 32 GPIO lines multiplexed with on-chip peripherals. The CPU08 core executes a CISC instruction set with extensions such as BGND, STOP, and WAIT low-power modes. The 48-LQFP package measures 7x7 mm and supports standard surface-mount assembly with an exposed-pad thermal path for improved heat dissipation. From an architectural standpoint, the HC08AP family uses a unified memory map, Harvard-style bus architecture for simultaneous instruction fetch and data access, and on-chip in-system programmable Flash. The integrated 10-bit ADC typically provides 8 to 15 channels depending on variant, supporting both single-ended and differential conversions. Hardware timers, a serial communications interface (SCI), and a serial peripheral interface (SPI) round out the peripheral set, enabling motor control, sensor aggregation, and human-machine interface (HMI) functions on a single chip. Typical applications include industrial automation controllers, white-goods and appliance control boards, HVAC damper and thermostat actuators, automotive body and chassis ECUs (non-safety), low-end point-of-sale terminals, and general-purpose embedded control where cost per node is the dominant constraint. Engineers most often select this part for its mature toolchain (CodeWarrior HC08, Cosmic, IAR), deterministic interrupt latency, and robust Flash security features. When designing with this device, plan for an external decoupling capacitor network near VDD/VSS pins and reserve the RESET pin for a proper supervisory reset circuit. The part is approaching end-of-life; new designs should evaluate modern Kinetis (Cortex-M0/M4) or S08 successors for long-term availability while preserving the HC08 family for legacy maintenance and cost-down retrofits. This page synthesizes distributor pricing, verified pin-compatible HC08 family alternatives, and practical design notes not found in the original NXP datasheet, including migration paths to active Kinetis and S08 families.

RFQ Liên hệ
MC908AP32CFBE - 8-Bit HC08 MCU 32KB Flash 44-QFP | NXP
MC908AP32CFBE

MC908AP32CFBE - 8-Bit HC08 MCU 32KB Flash 44-QFP | NXP

The NXP (Freescale) MC908AP32CFBE is an 8-bit HC08 microcontroller with 32KB (32K x 8) FLASH program memory, an 8MHz maximum bus clock, a 10-bit ADC, and a 44-pin QFP (10x10 mm) package. It is a member of the low-cost, high-performance M68HC08 family built around the enhanced CPU08 CISC core. An 8-bit microcontroller is a single-chip embedded processor that integrates a CPU core, program memory (FLASH), RAM, timers, analog-to-digital conversion, and general-purpose I/O on one die, sitting at the entry level of the microcontroller hierarchy (MCU -> embedded processor -> integrated circuit). The HC08 family was widely deployed in cost-sensitive industrial and appliance control before the industry migrated to ARM-based MCUs. Key features of the MC908AP32CFBE include 32KB of in-system-programmable FLASH with sector erase, a 10-bit ADC for analog sensor inputs, a high-speed timer module for PWM generation and input capture, and low-power operation modes (wait and stop) suited to battery- and energy-conscious designs. The CPU08 core delivers efficient CISC instruction execution at up to 8MHz, with a background debug mode for in-circuit development without costly emulators. Architecturally, the device combines the CPU08 core with on-chip FLASH, SRAM, a watchdog (COP), oscillator options, and serial and timer peripherals. The 3.3V/5V supply flexibility (per distributor listings of this family) and the 44-pin PQFP format with 10x10mm body make it suitable for compact two- and four-layer industrial PCBs with through-hole-equivalent serviceability. Typical applications include small motor control, appliance and white-goods control panels, industrial sensor nodes, battery chargers, and legacy communication modules - anywhere a modest 8-bit core with integrated ADC and FLASH keeps bill-of-materials cost low. When designing with this device, verify bus frequency versus supply voltage per the datasheet, and note that NXP lists this part as End of Life - new designs should not start here; existing designs should plan a replacement. This page synthesizes distributor data, lifecycle status, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Liên hệ
MC908AP64ACBE - HC08 8-Bit 8MHz 64KB FLASH MCU 42-SDIP | NXP
MC908AP64ACBE

MC908AP64ACBE - HC08 8-Bit 8MHz 64KB FLASH MCU 42-SDIP | NXP

The NXP MC908AP64ACBE is an 8-bit microcontroller from the M68HC08 family, specifically the HC08AP sub-family with on-chip high-speed oscillator support, delivering 8MHz CPU performance and 64KB of on-chip FLASH program memory in a 42-pin shrink-DIP (SDIP, 0.600" / 15.24mm) through-hole package. The device integrates 2KB of RAM, 30 general-purpose I/O lines, and a CPU08 core, providing CISC instruction-set execution for embedded control tasks. What is an HC08 microcontroller? The HC08 is an 8-bit CISC microcontroller architecture from the Freescale/NXP M68HC08 family. It belongs to the broader hierarchy: microcontroller -> embedded MCU -> single-chip computer -> semiconductor. HC08 devices evolved from the earlier M68HC05 architecture, adding a wider instruction set, enhanced addressing modes, a low-power STOP/WAIT mode, and on-chip FLASH program memory. The 'AP' suffix denotes the HC08AP variant, which includes an internal high-speed oscillator and Phase-Locked Loop (PLL) option, allowing operation from a low-frequency external crystal or resonator while the internal bus runs at the higher 8MHz rate. Key features include 64KB (64K x 8) FLASH program memory, 2KB (2K x 8) RAM, 30 I/O pins, internal oscillator with PLL, and on-chip peripherals covering LED drivers, Low-Voltage Detect (LVD), Power-On Reset (POR), Pulse-Width Modulation (PWM) channels, and serial communication interfaces (SCI, SPI, I2C). The 5V single-supply operation simplifies analog interface design. The CPU08 core implements a CISC instruction set with up to 16 addressing modes, supporting efficient C and assembly code generation. The internal bus architecture integrates FLASH for program storage and RAM for data, allowing single-chip operation. The HC08AP variant's PLL-based clock system trades an external high-frequency crystal for cost savings. Typical applications include industrial control, automotive body electronics, white-goods motor control, security systems, and consumer appliance control. Designers select this MCU for legacy Freescale/NXP code reuse, FLASH-based in-application reprogrammability, and the SDIP through-hole package that supports prototyping and field-serviceable designs. When designing with this part, note that the SDIP-42 footprint requires through-hole PCB assembly; engineers migrating to surface-mount should select the 44-pin QFP variant of the same die. Always confirm FLASH endurance (typically 100K cycles) and retention specifications against the in-application update requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Liên hệ
MC908AP64ACFAE - 8-Bit 8MHz 64KB MCU | NXP | 48-LQFP
MC908AP64ACFAE

MC908AP64ACFAE - 8-Bit 8MHz 64KB MCU | NXP | 48-LQFP

The NXP Semiconductors MC908AP64ACFAE is an 8-bit HC08 microcontroller with an 8 MHz CPU, 64 KB flash memory, and a 48-LQFP 7 x 7 mm package. The verified product information identifies EPP configuration, high-speed oscillator support, tray packaging, and a minimum package quantity of 250. It belongs to the HC08AP family and targets embedded control designs requiring flash storage, an 8-bit CPU, and a compact low-profile quad flat package. The device is suitable for industrial, appliance, instrumentation, and general embedded-control applications where deterministic control and integrated memory are useful. Its 48-terminal package provides a comparatively high pin count for an 8-bit MCU, supporting external peripherals and signal connections while maintaining a surface-mount footprint. An 8-bit microcontroller is a compact computer optimized for embedded control tasks such as sensing, decision logic, actuator control, and communication. The HC08 architecture provides a cost-effective platform for products that do not require the processing power of a 32-bit MCU. The MC908AP64ACFAE combines flash program memory with an 8 MHz operating specification, making it relevant to designs that need more memory than a small entry-level microcontroller while retaining an 8-bit architecture and low-cost implementation approach. Key verified characteristics include 8-bit processing, an 8 MHz maximum stated operating frequency, 64 KB flash organized as 64K x 8, and a 48-LQFP package measuring 7 mm x 7 mm x 1.4 mm with 0.5 mm pitch. The NXP product listing specifies high-speed oscillator and EPP variants. These details support designs requiring external clock integration, expanded peripheral access, or a conventional leaded quad flat package that can be assembled with standard surface-mount production processes. The part is identified by NXP as an HC08AP-series microcontroller. The verified distributor description also characterizes it as an 8-bit, 8 MHz, 64 KB flash MCU in a 48-LQFP package. The 64 KB flash capacity provides a practical balance between firmware size and device integration, allowing application logic, calibration data, and control routines to reside on the same device rather than requiring a separate program-memory component. The package dimensions and terminal count are important PCB-planning inputs when checking footprint compatibility. Typical embedded uses include motor and appliance control, sensor conditioning, keyboard or panel interfaces, simple measurement systems, and low-cost automation controllers. The 8 MHz CPU is appropriate for supervisory and deterministic control loops rather than graphics, high-bandwidth signal processing, or complex networking workloads. When selecting this MCU, verify the complete manufacturer datasheet for electrical limits, oscillator options, memory organization, peripheral availability, and pin-level multiplexing before finalizing a new design or replacement. For direct sourcing, the NXP listing gives a budgetary price of $8.75 USD at 10K quantity as of 2026-10-21, while LCSC lists a starting price of $14.9902. These prices are commercial reference points rather than guaranteed quotations. XAIPART availability, lead time, and exact packaging configuration should be confirmed against the current manufacturer and distributor records before purchase.

RFQ Liên hệ
MC908AP64CBE - 8-Bit 8MHz 64KB Flash MCU | NXP
MC908AP64CBE

MC908AP64CBE - 8-Bit 8MHz 64KB Flash MCU | NXP

NXP Semiconductors MC908AP64CBE is an 8-bit HC08 microcontroller operating at 8MHz, with 64KB (64K x 8) embedded flash memory and a 42-pin PDIP package. It is designed for embedded control applications requiring a compact 8-bit CPU, on-chip program memory, and integrated peripherals. The verified distributor data identifies the device as an HC08-family microcontroller and confirms its 8-bit architecture, 8MHz operating frequency, 64KB flash capacity, and 42-pin package. These values should be treated as the core procurement identity for replacement and design matching. An HC08 microcontroller is a single-chip embedded controller within the broader semiconductor and embedded-processing hierarchy. It combines a CPU core, flash program memory, data memory, digital I/O, timers, and communication or control peripherals on one integrated circuit. This integration allows a product to execute control firmware and manage sensors, switches, actuators, or communication interfaces without requiring separate memory. The MC908AP64CBE is therefore a general-purpose 8-bit embedded MCU rather than a discrete logic IC or analog regulator. The verified product data highlights a 64K x 8 flash organization, meaning 64K eight-bit storage locations, and an 8MHz operating speed. The 42-pin PDIP package supports conventional through-hole PCB assembly and provides the external signal and power connections required by the HC08 device family. The verified distributor descriptions also associate the part with a 10-bit ADC application feature, although detailed ADC operating conditions are not provided in the supplied data. Do not infer resolution, accuracy, or conversion timing beyond that explicit 10-bit ADC association. MC908AP64CBE can be used in industrial control, appliance control, instrumentation, low-cost embedded products, and legacy embedded systems where a dedicated 8-bit controller is preferred over a higher-performance processor. The 64KB flash capacity provides room for firmware and application logic, while the 8-bit CPU architecture can simplify resource-constrained control loops. Engineers should verify the complete pinout, supply limits, clock configuration, memory map, and peripheral behavior against the official Freescale or NXP datasheet before finalizing a new design. Because this is a legacy DIP MCU, PCB decisions should be driven by package outline, pin numbering, programming method, and signal requirements rather than only the base part number. A distributor listing may show the HC08 family, flash size, speed, and package, but it does not replace a full manufacturer datasheet for production qualification. Confirm authorized sourcing and current lifecycle status during procurement. This page consolidates verified distributor specifications, sourcing context, and practical replacement-selection guidance for MC908AP64CBE. Pricing, complete pin names, detailed ADC specifications, voltage limits, and verified drop-in alternatives are not available in the supplied data and must not be guessed.

RFQ Liên hệ
MC908AP64CFAE - 8-Bit 8MHz 64KB MCU | NXP | Automotive
MC908AP64CFAE

MC908AP64CFAE - 8-Bit 8MHz 64KB MCU | NXP | Automotive

NXP Semiconductors MC908AP64CFAE is an 8-bit HC08 microcontroller operating at 8 MHz, with 64 KB flash memory, 2 KB RAM, an 8-channel 10-bit ADC, and LIN capability in a 48-LQFP 7x7 mm package. It is positioned for automotive and industrial control systems where compact embedded control, analog measurement, and serial connectivity are required. A microcontroller is a programmable embedded-control component that combines a CPU, memory, peripherals, and input/output functions on one integrated circuit. The MC908AP64CFAE belongs to the HC08 family of 8-bit devices and is designed for cost-sensitive control platforms that need deterministic peripheral integration without a high-performance processor core. Its 64 KB flash provides program storage, while 2 KB RAM supports working data and stack operations. The key feature set includes an 8 MHz CPU08 microcontroller core, 64 KB flash, 2 KB RAM, an 8-channel ADC identified by distributor data as a 10-bit ADC, and LIN capability. The 48-LQFP 7x7 mm package provides a substantial lead count for external peripherals and automotive or industrial signal connections. Exact pin names, voltage limits, clock details, ADC timing, and electrical limits should be confirmed in the NXP manufacturer documentation. Because this is an embedded MCU rather than a power semiconductor, its architecture is centered on firmware execution and peripheral connectivity. The ADC can support sensor acquisition and threshold-based control, while LIN capability can support low-cost vehicle or distributed industrial networks. Firmware, external clocking, memory programming, and peripheral configuration must be matched to the system requirements before production release. Typical applications include automotive body-control modules, LIN-connected nodes, industrial sensor controllers, actuator controllers, compact embedded systems, and low-cost control panels. The 8-bit architecture is appropriate when the workload is mainly I/O, state-machine, timer, and analog-signal processing rather than intensive computation, graphics, or high-bandwidth communications. Design consideration: place the MCU power, decoupling, clock, reset, and debug or programming connections according to the NXP datasheet reference layout. Confirm package pin compatibility and peripheral mappings before substituting any candidate. This page combines verified manufacturer and distributor information with practical design context, comparison criteria, and application guidance.

RFQ Liên hệ
MC908AP64CFAER - HC08 8-Bit MCU, 64KB FLASH, 48-LQFP | NXP
MC908AP64CFAER

MC908AP64CFAER - HC08 8-Bit MCU, 64KB FLASH, 48-LQFP | NXP

The NXP (formerly Freescale) MC908AP64CFAER is a member of the HC08AP family of 8-bit microcontrollers built around the enhanced M68HC08 central processor (CPU08). The device integrates 64KB of FLASH program memory, runs at 8MHz, and is housed in a 48-pin LQFP (7x7 mm) package. It targets low-cost, high-performance embedded control with on-chip 10-bit ADC support. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (program FLASH and data RAM), and programmable I/O peripherals. The 8-bit MCU category belongs to the embedded microcontroller taxonomy, sitting under microcontroller -> embedded controller -> integrated circuit. The HC08 family succeeded the HC05/HC11 lines and served as a workhorse for automotive body controllers, industrial control, and consumer appliances through the 2000s and early 2010s before the S08 and Cortex-M families superseded it. Key features include 64KB (64K x 8) FLASH program memory, 2KB RAM, 32 programmable I/O lines, an internal oscillator, an integrated 10-bit ADC, and a 3.3V/5V operating range. The part number suffix 'FA' designates the 48-LQFP (7x7) package per Freescale's legacy naming convention, and 'ER' denotes tape-and-reel packaging for high-volume SMT assembly. Architecture depth: the CPU08 core delivers BCD arithmetic, indexed addressing, and a HALT/STOP low-power mode. The internal oscillator and FLASH allow BOM simplification versus external crystal MCUs. The 10-bit ADC supports up to 8 analog input channels depending on package variant, enabling sensor-interface applications without external ADCs. Typical applications include automotive body modules (wipers, seat controllers), industrial control panels, white goods motor control, and low-end consumer devices. The HC08 instruction set and tool ecosystem (CodeWarrior HC08) make it suitable for legacy designs and cost-sensitive retrofits. A critical design consideration: this part is in lifecycle EOL/NRND status at NXP. Before new design-in, verify availability through distributors like Rochester Electronics (which holds legacy stock) and confirm long-term supply. This page consolidates distributor pricing from DigiKey, Mouser, Octopart and Heisener alongside same-family NXP alternatives not found in the bare manufacturer datasheet.

RFQ Liên hệ
MC908AP64CFAER528 - 8-bit HC08 MCU 64KB Flash 48-LQFP | NXP
MC908AP64CFAER528

MC908AP64CFAER528 - 8-bit HC08 MCU 64KB Flash 48-LQFP | NXP

The NXP (Freescale) MC908AP64CFAER528 is a member of the HC08AP family of 8-bit microcontrollers featuring 64KB of on-chip Flash program memory, 2KB of RAM, an 8-channel 10-bit ADC, and an 8MHz CPU08 core, all integrated into a 48-pin LQFP (7x7 mm) surface-mount package supplied on Tape & Reel. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating a CPU, program storage (Flash/ROM), working memory (RAM), and a fixed set of peripheral interfaces such as timers, ADC channels, communication ports, and GPIOs onto a single silicon die. Within the broader taxonomy of semiconductors, 8-bit MCUs sit beneath 32-bit microcontrollers and microprocessors; the MC908AP64 belongs to the M68HC08 family, an evolutionary successor to the classic M68HC05 family. The HC08AP family specifically targets low-cost, high-volume automotive body electronics and industrial control applications that benefit from on-chip Flash, a 10-bit ADC, and LIN-friendly timer architecture. Key features of the MC908AP64CFAER528 include 64KB (64K x 8) Flash program memory, 2KB of on-chip RAM, 32 general-purpose I/O lines, an internal oscillator that eliminates external crystal cost, and a 10-bit successive-approximation ADC with up to 8 input channels. The CPU08 core runs at 8MHz bus frequency and offers an extended instruction set over the older HCO5 core. The 48-LQFP package exposes 32 I/Os to the PCB, providing generous routing flexibility for mixed analog/digital designs while keeping the die footprint compact at 7 x 7 mm. Typical applications include automotive body control modules (BCMs), instrument clusters, HVAC actuators, LIN slave nodes, white-goods motor control boards, security and alarm panels, and small industrial sensor-conditioning boards. Designers also use the HC08AP64 in low-cost replacement designs for legacy HC05 systems where migration to a higher-end Cortex-M0+ device is not economically justified. The integrated 10-bit ADC with 8 channels is well-matched to resistive-bridge and thermistor analog front-ends typical in appliance and HVAC systems. When designing with the MC908AP64CFAER528, plan for the part's 5V-tolerant I/O, leave generous decoupling on VDD/VSS pairs (100 nF plus 10 uF bulk), and route the ADC reference pin (VREF) away from switching nodes. The part is well-supported by Freescale/NXP's CodeWarrior HC08 toolchain and P&E Micro's Cyclone/Multilink debug hardware, which simplifies prototype bring-up and in-field firmware updates. This page synthesizes distributor pricing, same-package drop-in alternatives within the HC08AP family, and practical design notes (oscillator behavior, ADC accuracy, and debug-tool compatibility) that are not consolidated in the manufacturer datasheet alone.

RFQ Liên hệ
MC908AP8ACBE - 8-Bit HC08 MCU 8KB Flash 8MHz 42-PDIP
MC908AP8ACBE

MC908AP8ACBE - 8-Bit HC08 MCU 8KB Flash 8MHz 42-PDIP

The NXP MC908AP8ACBE is an 8-bit HC08 CISC microcontroller featuring 8KB of embedded Flash program memory, an 8MHz CPU clock, and a 42-pin SPDIP (Plastic DIP, 0.600 inch/15.24mm) through-hole package. Part of the legacy Freescale/NXP HC08 family, it integrates on-chip peripherals suitable for cost-sensitive industrial and consumer control tasks. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path, integrating CPU core, ROM/Flash program memory, RAM, and peripherals. The HC08 family is a CMOS successor to the Motorola 6805/68HC05 line, using a CISC instruction set with a von Neumann-style unified bus, on-chip in-circuit programmable Flash, and dedicated timers/ADC modules. Within the broader taxonomy, the MC908AP8ACBE sits in microcontroller ICs -> microcontrollers -> embedded processors -> 8-bit MCU category, optimized for low-power deterministic control rather than computational throughput. Key differentiating specifications include the 8KB Flash program array (in-system programmable), 256 bytes of RAM (typical of the AP8 mask set), an internal oscillator with optional external crystal support, multiple timer channels, and a 10-bit ADC option in the package. The HC08 core executes a CISC instruction set with BCD arithmetic support, and the on-chip ICE (in-circuit emulation) via background debug mode simplifies firmware development on legacy platforms. The MC908AP8ACBE is built on a 5V CMOS process with a typical operating voltage of 4.5V to 5.5V and is rated for the industrial temperature range of -40C to +85C. The 42-pin SPDIP footprint provides ample I/O for human-machine interface, motor drive, and sensor conditioning PCB layouts while keeping manufacturing compatible with through-hole assembly lines. Typical applications include industrial control modules, white-goods and home-appliance controllers, security panel keypads, automotive body-electronics nodes (non-AEC-Q100), and educational/development boards demonstrating HC08 instruction flow. Designers should consult the NXP MC908AP8ACBE datasheet for the exact ADC channel count, timer configuration, and the recommended decoupling/bulk capacitor placement around VDD/VDDA pins when migrating code from the older MC68HC908AP8 mask parts. This page consolidates distributor pricing, real cross-reference alternatives in the same 42-PDIP footprint, and engineering design notes not present in the manufacturer datasheet summary.

RFQ Liên hệ
MC908AP8ACFBE - HC08 8-Bit MCU 8KB Flash 44-QFP | NXP
MC908AP8ACFBE

MC908AP8ACFBE - HC08 8-Bit MCU 8KB Flash 44-QFP | NXP

The NXP MC908AP8ACFBE is an 8-bit microcontroller from the M68HC08 family, specifically the HC08AP sub-family, featuring an 8KB flash program memory and operating at 8MHz internal bus speed with a high-speed oscillator option. Housed in a 44-pin QFP (10x10 mm) package, this MCU integrates the enhanced M68HC08 central processor (CPU08) with 8KB on-chip FLASH, RAM, and a rich set of peripherals including timers, serial communications interfaces (SCI), SPI, and I2C. What is an HC08 microcontroller? The HC08 (short for M68HC08) is an 8-bit CISC microcontroller architecture from NXP/Freescale that evolved from the earlier M68HC05 family. MCUs in this category are valued for low cost, deterministic behavior, and ease of programming in embedded control. Within the wider taxonomy, HC08 sits under: 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor IC. The HC08AP family specifically is the high-speed-oscillator version of the HC08AP family, optimized for applications requiring higher clock flexibility. Key features include 8KB FLASH program memory, 256 bytes of RAM (typical HC08AP figure), an 8-channel 8-bit ADC, multiple timers, an internal high-speed oscillator option, and multiple communication peripherals (SCI, SPI). The device operates from 3V to 5.5V supply, typical for 5V industrial and consumer systems. The 44-QFP package offers generous I/O and ease of prototyping. The HC908AP family uses a CISC architecture with a 16-bit index register and 8-bit accumulator, supporting BCD arithmetic and flexible addressing modes. The integrated FLASH allows in-application reprogramming, useful for field updates and calibration storage. The device targets cost-sensitive embedded control where 32-bit performance is unnecessary but reliability and peripheral integration are required. Typical applications include appliance control (washing machines, microwaves, HVAC), industrial sensors, automotive body electronics, motor control for small BLDC/brushed DC systems, remote controls, and consumer white goods. The 5V-tolerant design suits traditional 5V analog signal chains often found in industrial sensor interfaces. A key design consideration when using the MC908AP8ACFBE is its EOL (End-of-Life) status per NXP - designers planning new production should evaluate the MC908AP16CFBE, MC908AP32CFBE, or migrate to the newer S08 family (e.g., MC9S08). For legacy maintenance and repair, sourcing through authorized distributors is recommended. Power dissipation in the 44-QFP is modest at typical 8MHz operation, but PCB layout must still decouple VDD/VSS adequately. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Liên hệ
MC908AP8CBE - 8KB Flash 8-bit HC08 MCU 42-DIP | NXP
MC908AP8CBE

MC908AP8CBE - 8KB Flash 8-bit HC08 MCU 42-DIP | NXP

The NXP MC908AP8CBE is an 8-bit HC08 family microcontroller (MCU) featuring 8 KB of on-chip FLASH program memory, 1 KB of RAM, an internal oscillator, a 10-bit ADC, and 30 general-purpose I/O pins, all packaged in a 42-pin SPDIP (PDIP) through-hole module. The device operates across a 3.3 V / 5 V supply range at a CPU bus frequency of 8 MHz using an internal clock source, with the CISC HC08 core providing a familiar register and instruction set for legacy automotive and industrial designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH/ROM), data memory (RAM), peripherals (ADC, timers, communication ports), and I/O on one die. The HC08 architecture sits under the broader taxonomy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. 8-bit MCUs remain widely deployed in cost-sensitive, low-power, deterministic-control applications such as appliance control, motor drivers, automotive body electronics, and industrial sensor conditioning where their simplicity and predictable interrupt response outperform more complex 32-bit parts. Key features of the MC908AP8CBE include 8 KB FLASH for in-application or in-circuit reprogramming, 1 KB of static RAM for data and stack, a 10-bit successive-approximation ADC for analog sensing tasks, multiple timers and a serial communications interface (SCI), and a 42-pin SPDIP footprint that is breadboard-friendly for prototyping and field-service replacement. The part runs directly from a 3.3 V or 5 V rail without external oscillator components. The HC08 core uses a von Neumann-style CISC architecture with a small instruction set, accumulator-based addressing and indexed modes, plus an integrated background debug module (BDM) that enables in-circuit programming and non-intrusive debugging through a single-wire interface. Internal oscillator trimming and watchdog operation reduce external component count and improve field reliability. Typical applications include automotive body controllers, HVAC fan and damper drivers, appliance user-interface boards, low-cost industrial sensors, white-goods motor control, and legacy embedded platforms that need a long-lifecycle pin-compatible MCU. The 42-pin SPDIP package is also popular in educational kits and developer boards because it accepts standard IC sockets. When designing with the MC908AP8CBE, plan for FLASH endurance and write timing in production firmware, and add proper decoupling (0.1 uF ceramic plus bulk) on VDD/VSS pins. The BDM pinout should be reserved on the PCB even if unused so that field updates and diagnostics are possible throughout the product lifecycle. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, drop-in alternative listings from the same HC08 family, and practical engineering notes not found in a single manufacturer document - giving procurement and engineering teams a single reference point for sourcing and design-in decisions.

RFQ Liên hệ
MC908AP8CFAE - HC08 8-bit MCU 8KB Flash 48-LQFP | NXP
MC908AP8CFAE

MC908AP8CFAE - HC08 8-bit MCU 8KB Flash 48-LQFP | NXP

The NXP MC908AP8CFAE is an 8-bit HC08-family microcontroller featuring an 8KB flash program memory, an integrated 10-bit ADC, and 48-pin LQFP packaging, designed for automotive and industrial embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for deterministic control tasks in cost-sensitive embedded systems. MCUs integrate a CPU core, non-volatile program memory (typically Flash), volatile RAM, peripherals such as ADC, timers, and communication interfaces (UART, SPI, I2C), into one package. The HC08 family from NXP (formerly Freescale) is a CISC architecture succeeding the popular HC05/HC11 lines, offering higher code density, a wider instruction set, and enhanced low-power modes. Within that family, the MC908AP sub-family targets automotive and industrial motor-control and instrumentation. Key features of the MC908AP8CFAE include an 8 MHz maximum CPU bus clock, 8KB on-chip Flash with in-system programmability, 1KB on-chip RAM, a 10-bit resolution analog-to-digital converter (ADC) with multiple input channels, and enhanced low-power modes (STOP and WAIT) for battery-friendly operation. The device also integrates a timer interface module, a serial communications interface (SCI) and serial peripheral interface (SPI), and an external interrupt module with keyboard wake-up capability. The architecture is built on NXP's mature HC08 CISC core using a 3.3V/5V dual-voltage design that simplifies interfacing to both 5V analog sensors and 3.3V digital logic. The wide operating voltage range and automotive-qualified process technology make it suitable for under-hood and industrial control environments where electrical noise and temperature extremes are common. Typical applications include automotive body controllers, instrument cluster sub-systems, HVAC actuators, low-end motor control, sensor signal conditioning, and small industrial appliances. Designers choose this part when deterministic real-time control, long Flash retention (data retention over automotive life), and a stable, multi-sourced tool chain (CodeWarrior HC08, Cosmic, IAR) are required. When designing with this MCU, ensure the brown-out reset voltage threshold is configured to match the minimum operating voltage (3V) of the system, and place decoupling capacitors close to each VDD/VSS pin pair. The LQFP-48 package provides adequate thermal dissipation for the HC08's modest power budget but still requires a small ground plane to keep digital switching noise away from the analog AVdd reference. This page synthesizes distributor pricing, drop-in same-family NXP alternatives, cross-references to pin-compatible variants, and practical design notes not found in the standalone manufacturer datasheet.

RFQ Liên hệ
MC908AP8CFBE - 8-Bit HC08 MCU, 8KB Flash, 8MHz, 44-QFP | NXP
MC908AP8CFBE

MC908AP8CFBE - 8-Bit HC08 MCU, 8KB Flash, 8MHz, 44-QFP | NXP

The NXP MC908AP8CFBE is an 8-bit HC08-family microcontroller (MCU) with 8KB of Flash program memory and a CPU clock speed of 8 MHz, housed in a 44-pin LQFP (10x10 mm) surface-mount package. It integrates a 10-bit ADC, multiple timers, and serial interfaces on a single die, targeting cost-sensitive embedded control applications. What is an 8-bit microcontroller? An 8-bit microcontroller is a single-chip computer that uses an 8-bit data path and is widely deployed in cost-constrained, deterministic embedded systems. It belongs to the broader category of microcontrollers, which in turn are a subset of microprocessors with integrated memory and peripherals. The HC08 family, in particular, descends from the M68HC08 lineage and targets low-cost, high-reliability motor, appliance, and industrial control designs. Key features include 8KB of on-chip FLASH program memory, 1KB of RAM, an internal oscillator, a 10-bit analog-to-digital converter, 32 general-purpose I/O pins, and timer modules. The device operates from a single 3.3V/5V supply and includes a 44-pin QFP (10x10 mm) package suitable for space-constrained boards. The MC908AP8CFBE is built on the M68HC08 CPU architecture (CPU08) with CISC-style instruction set, providing efficient code density and low-cycle interrupts. Its FLASH-based program memory allows fast in-circuit reprogramming during prototyping and field updates. The integrated 10-bit ADC and timers make analog signal acquisition and PWM control feasible without external ICs. Typical applications include appliance control, motor drives, lighting control, low-end consumer electronics, and industrial automation sensor interfaces. The 8MHz CPU combined with 32 GPIO makes the device well suited to replacing discrete logic in legacy designs. When designing with this MCU, ensure that the internal oscillator accuracy is sufficient for your timing-critical UART, or use an external crystal. The 32 GPIO share pins with peripheral functions, so reserve clock and reset pins early in the schematic capture process. This page synthesizes distributor pricing, same-family alternatives, and practical design notes for engineers evaluating the MC908AP8CFBE, complementing the NXP datasheet with selection guidance.

RFQ Liên hệ
MC908AS32ACFNE - HC08 8-bit MCU 32KB Flash 8.4MHz | NXP 52-PLCC
MC908AS32ACFNE

MC908AS32ACFNE - HC08 8-bit MCU 32KB Flash 8.4MHz | NXP 52-PLCC

The NXP MC908AS32ACFNE is an 8-bit HC08 CISC microcontroller IC with 32KB Flash program memory, 1KB RAM, and an 8.4MHz CPU core, housed in a 52-pin PLCC (Plastic Leaded Chip Carrier) J-lead package measuring 19.1 x 19.1 mm. The part is part of NXP/Freescale's HC08 family targeted at automotive and industrial embedded applications, supporting SCI and SPI connectivity for serial communication. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADCs, and serial interfaces into one IC. The HC08 family sits within the broader CISC (Complex Instruction Set Computer) microcontroller hierarchy, which generally favors compact code density and deterministic interrupt response over raw clock speed. MCUs are the lowest tier of embedded computing devices, above which sit microprocessors (MPUs), DSPs, FPGAs, and application processors. The HC08 architecture specifically targets cost-sensitive, low-power automotive body and chassis electronics. Key features of the MC908AS32ACFNE include 32KB of in-application Flash for program storage, 1KB of RAM for data, 40 programmable I/O lines, an integrated internal oscillator, and a 5V supply rail. The device is qualified for automotive temperature grades, making it suitable for under-hood and body-electronics modules where ambient temperatures routinely span -40C to +125C. The CISC core executes the HC08 instruction set with a maximum internal bus clock of 8.4MHz, providing adequate throughput for body-control and sensor-interface tasks without excessive power consumption. The HC08 core uses a von Neumann architecture with a 16-bit program counter and 8-bit ALU, supporting addressing modes optimized for embedded C code generation. The internal oscillator eliminates the need for an external crystal in cost-sensitive designs, while the integrated 5V regulator rail simplifies power-tree design in automotive 12V battery systems. Flash memory enables in-circuit reprogramming for firmware updates in the field. Typical applications include automotive body control modules, instrument cluster controllers, HVAC panel interfaces, simple sensor conditioning nodes, and industrial appliance controllers. The wide operating voltage and temperature range also suits industrial automation tasks where reliability over decades of field service is required. When designing with this MCU, ensure your firmware toolchain supports the HC08 instruction set (legacy Cosmic, CodeWarrior HC08, or compatible). Plan for an ICD (in-circuit debugger) header on the PCB since HC08 devices are programmed and debugged via a MON08 or background-debug-mode interface that typically requires a few dedicated pins. This page synthesizes distributor pricing, same-package drop-in alternatives, and engineering design notes that complement the manufacturer datasheet, supporting engineers who are maintaining legacy HC08 designs or evaluating long-term supply options.

RFQ Liên hệ
MC908AS60ACFN - 8-Bit HC08 MCU, 60KB Flash, 8.4MHz, 52-PLCC | NXP
MC908AS60ACFN

MC908AS60ACFN - 8-Bit HC08 MCU, 60KB Flash, 8.4MHz, 52-PLCC | NXP

The NXP Semiconductors MC908AS60ACFN is an 8-bit HC08 HCMOS microcontroller unit (MCU) featuring 60KB of on-chip Flash program memory and 1KB of RAM, operating at a bus frequency of 8.4 MHz, housed in a 52-pin PLCC (Plastic Leaded Chip Carrier) package measuring 19.1 x 19.1 mm. The part belongs to the MC68HC908AS60A family and integrates an 8-bit CPU08 core with a rich peripheral set including timers, an SCI (Serial Communications Interface), an SPI (Serial Peripheral Interface), and a CAN 2.0A/B controller module for in-vehicle networking. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a configurable set of on-chip peripherals (timers, ADC, communication controllers, GPIO). MCUs occupy the bottom of the embedded system hierarchy (MCU -> embedded controller -> SoC -> computer) and are the workhorse of deterministic real-time control in automotive body electronics, industrial PLCs, consumer white goods, and motor control. The HC08 family is NXP/Freescale's legacy 8-bit architecture optimized for low cost, low power, and predictable interrupt latency. Key features of the MC908AS60ACFN include 60KB (60K x 8) of Flash, 2KB of EEPROM for data storage, 1KB of RAM, 8.4 MHz maximum internal bus frequency, an integrated 8-channel 8-bit ADC, two 16-bit timer channels, MSCAN (Motorola Scalable CAN) module for CAN 2.0A/B, and an operating voltage range of 4.5V to 5.5V. The 52-pin PLCC package supports through-hole and socket mounting, making it convenient for legacy designs, prototyping, and field-replaceable modules. The Flash memory supports in-application programming via a background debug mode (BDM) interface. The MC908AS60ACFN's MSCAN module implements CAN 2.0A and 2.0B active and passive error counters, programmable bit timing, and a flexible acceptance filter, enabling reliable communication on automotive CAN buses at 1 Mbit/s. The integrated EEPROM emulates 2KB of byte-erasable non-volatile storage suitable for parameter retention across power cycles without external EEPROM ICs. The 8-channel ADC supports both single-ended and differential conversions with 8-bit resolution, suitable for sensor monitoring and battery management. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, simple motor control (small DC and stepper), industrial sensor interfaces, and legacy appliance control boards that require a CAN interface and small Flash footprint. The 52-pin PLCC socketed package is favored in automotive production lines where field rework and firmware updates are routine. When designing with this part, note that the PLCC package is socket-friendly but consumes substantially more PCB area than a QFP equivalent. Decouple VDD/VSS pairs with 100 nF ceramic capacitors placed within 5 mm of each pin pair. Use the BDM (Background Debug Mode) interface for in-circuit programming and debug, and reserve a 4-pin header for the BDM pod. This page consolidates distributor pricing, parametric data, and practical design notes for engineers maintaining legacy HC08 designs and evaluating long-term sourcing options for the MC908AS60ACFN.

RFQ Liên hệ
MC908AS60ACFNE - 8-bit HC08 MCU 60KB Flash 8.4MHz PLCC-52 | NXP
MC908AS60ACFNE

MC908AS60ACFNE - 8-bit HC08 MCU 60KB Flash 8.4MHz PLCC-52 | NXP

The NXP (formerly Freescale) MC908AS60ACFNE is an 8-bit microcontroller from the M68HC08 family, featuring 60KB of FLASH program memory and 2KB of EEPROM, housed in a 52-pin PLCC (J-Lead) package measuring 19.1 mm x 19.1 mm. Operating at up to 8.4 MHz from the enhanced M68HC08 CPU08 core, the device belongs to the HC08AS/AZ low-cost, high-performance sub-family. The part is currently in End-of-Life status per the NXP product page, meaning authorized distributor stock is the only remaining supply path. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The HC08 family represents the 8-bit branch of the broader Motorola/Freescale/NXP M68HCxx lineage, which sits within the larger category of embedded microcontrollers -> microprocessors -> digital ICs -> semiconductors. The 8-bit MCU segment remains relevant for cost-sensitive, deterministic, low-power embedded applications where ARM Cortex-M overhead is unnecessary. Key features of the MC908AS60ACFNE include 60KB (60K x 8) of FLASH program memory, 2KB of on-chip EEPROM for non-volatile data storage, an internal 8.4 MHz bus clock derived from the on-chip oscillator, and the standard HC08 peripheral set. The 52-pin PLCC package provides ample I/O for automotive body, appliance, and industrial control applications and supports surface-mount assembly with J-leads. Architecturally, the device uses the enhanced CPU08 core, which adds a few instructions and addressing modes over the original HC08 core while preserving code compatibility. The FLASH/EEPROM split enables field re-programmability for calibration data and protocol parameters, a useful feature for late-stage product customization or firmware updates. Typical applications include automotive body controllers, HVAC controls, appliance motor control, industrial sensor interface boards, and legacy embedded systems requiring proven 8-bit processing. The HC08AS/AZ family was widely adopted in automotive clusters and instrument panels. When designing with this MCU, note the End-of-Life status - qualify a successor early or commit to a last-time-buy inventory plan. Engineers should also evaluate migration paths to the S08 or S12 families for new designs since tooling, compilers, and development support for legacy HC08 parts are increasingly community-maintained. This page synthesizes distributor inventory data, drop-in replacement candidates from the HC08 family, and practical design considerations not found in the original manufacturer datasheet.

RFQ Liên hệ
MC908AS60ACFUE - 8-Bit 8.4MHz HC08 60KB Flash MCU | NXP
MC908AS60ACFUE

MC908AS60ACFUE - 8-Bit 8.4MHz HC08 60KB Flash MCU | NXP

The NXP MC908AS60ACFUE is an 8-bit HC08-family microcontroller (HC08AS) delivering 8.4 MHz CPU clock speed with 60KB of in-application flash program memory and 2KB of EEPROM, housed in a 64-pin QFP (14x14 mm) package. It provides 52 general-purpose I/O lines, an internal oscillator, and multiple timer and serial peripherals typical of the HC08 AS series. The integrated flash array supports byte-programmable in-circuit programming for production-line firmware update and field upgrades. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip built around an 8-bit data path, integrating a CPU, program memory (ROM/flash), RAM, peripherals (timers, ADC, communication ports), and general-purpose I/O onto one die. Within the broader hierarchy 8-bit MCU -> microcontroller -> embedded processor -> semiconductor, HC08 devices sit as a mature NXP family originally developed by Motorola/Freescale that has been deployed for decades in cost-sensitive, deterministic control tasks where 32-bit complexity is unnecessary. Key features include 60KB flash program memory, 2KB on-chip EEPROM for non-volatile data, 8.4 MHz internal bus clock (HC08AS core), 52 digital I/O pins multiplexed with peripheral functions, and an integrated internal oscillator that simplifies BOM by eliminating an external crystal for many applications. The 64-QFP package exposes the full peripheral set including multiple timer modules, an SCI (serial communications interface), and an SPI-compatible interface. The HC08AS core uses a von Neumann architecture with byte-addressable memory, a hardware stack, and a BCD-corrected arithmetic flag set. The 8.4 MHz bus clock delivers ~1.05 MIPS peak instruction throughput, sufficient for slower-speed polling loops, sensor fusion at modest sample rates, and brushed DC motor closed-loop control using software PID. On-chip in-circuit debugging (with optional background debug mode) permits break-point-based development without an expensive in-circuit emulator. Typical applications include industrial control boards, automotive body electronics sub-modules, motor drive BLDC/PMSM FOC ancillary tasks where a 32-bit DSP/MCU is overkill, household appliance controllers such as washing machines and dishwashers, and HVAC fan control panels. The wide software portability of the HC08 instruction set plus extensive legacy codebases keeps the AS60A in active demand in industrial retrofit designs. When designing with this device, verify whether the part is officially discontinued (the NXP product page marks this MPN as End-of-Life per the verified web data) and confirm the last-time-buy window before committing new designs. For new designs, evaluate pin-compatible Kinetis or S12K successors from NXP rather than designing in EOL silicon. This page synthesizes distributor pricing, 64-QFP drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Liên hệ
MC908AS60ACFUE-FR - 8-Bit HC08 MCU 60KB Flash 64-QFP | NXP
MC908AS60ACFUE-FR

MC908AS60ACFUE-FR - 8-Bit HC08 MCU 60KB Flash 64-QFP | NXP

The NXP (formerly Freescale) MC908AS60ACFUE-FR is an 8-bit HC08-family microcontroller integrating 60KB of on-chip FLASH program memory, 2KB of RAM, and a rich set of analog and digital peripherals in a 64-pin QFP (14x14 mm) package. It is part of the M68HC08AS-AZ series and is qualified to operate at a bus frequency of 8.4 MHz from a wide operating voltage range, making it a long-standing workhorse for cost-sensitive automotive body, industrial control, and appliance applications. An 8-bit microcontroller is a microprocessor integrated with FLASH program memory, RAM, timers, serial communication peripherals, and I/O on a single die. The HC08 is Freescale/NXP's 8-bit core family that succeeded the HC05 and offers an enhanced instruction set, on-chip FLASH, and a more modular peripheral architecture. MCUs such as the MC908AS60ACFUE-FR sit at the bottom of the embedded computing hierarchy: microcontroller -> embedded processor -> semiconductor IC. They are designed for deterministic, low-power control loops where 32-bit performance is unnecessary. Key features of this device include 60KB (60K x 8) of FLASH, 2KB (2K x 8) of RAM, 52 general-purpose I/O lines, an internal oscillator, and on-chip peripherals that typically include a timer/PWM module, an 8-channel 8-bit ADC, SCI and SPI serial interfaces, and a CAN 2.0B controller (consistent with the AS-series HC08 family). The 64-QFP (14x14) footprint is a widely-used through-hole-friendly surface-mount package that simplifies PCB layout and rework. The MC908AS60ACFUE-FR uses a von-Neumann bus architecture with the HC08 CPU core, an on-chip bandgap reference, low-voltage detect (LVD) and power-on reset (POR) for robust startup, and a system integration module that maps peripherals into a single linear address space. Peripherals are clock-gated to minimize quiescent current, and the internal clock source eliminates the external crystal in many designs. Typical applications include automotive body controllers (door modules, seat controllers, HVAC blowers), industrial PLCs and sensor transmitters, white-goods and appliance motor control, security alarm panels, and battery-powered metering. The wide temperature range and integrated CAN bus support also suit automotive networks and 12V/24V industrial systems. Designers should note that the -FR suffix typically denotes factory-reel packaging and identical die to the non-FR variant, so firmware and software are fully portable. This part is widely available through authorized distributors; users designing new products should verify the current lifecycle status with NXP, as the HC08 family is in mature / last-time-buy phase at many suppliers.

RFQ Liên hệ
MC908AS60AMFU - 8-Bit 8.4MHz HC08 Flash MCU | Freescale | 64-QFP
MC908AS60AMFU

MC908AS60AMFU - 8-Bit 8.4MHz HC08 Flash MCU | Freescale | 64-QFP

The Freescale Semiconductor MC908AS60AMFU is an 8-bit HC08-family flash microcontroller integrating 60 KB of on-chip flash memory, an 8.4 MHz HCS08-compatible CPU core, and a rich set of analog/digital peripherals, all packaged in a 64-lead QFP (QFP-64, 14x14 mm body, gull-wing leads). It is part of the HC908AS60A / HC908AZ60A automotive-grade MCU family originally developed by Motorola Semiconductor and now maintained by NXP / Freescale. Key parameters include 60 KB flash, 2 KB RAM, 8.4 MHz bus clock, a 5 V supply rail, and automotive-grade temperature rating. What is an HC08 microcontroller? The HC08 is Freescale/Motorola's 8-bit CISC microcontroller architecture that evolved from the earlier MC68HC05 line, adding a 16-bit index register, additional addressing modes, and a memory-mapped peripheral model. An HC08 Flash MCU integrates the CPU, Flash program memory, RAM, EEPROM/Flash-erase emulation, timers, ADC, serial communication interfaces, and I/O ports onto a single die - a System-on-Chip optimized for deterministic embedded control. Within the broader hierarchy, MC908AS60AMFU belongs to: microcontroller -> 8-bit MCU -> HC08 family -> HC908AS60A subgroup -> embedded computing. Key features include 60 KB of in-application programmable flash (suitable for firmware upgrades), 2 KB of SRAM for stack/data, multiple 16-bit timers, a 10-channel 8-bit ADC for sensor interfacing, SCI (UART) and SPI serial interfaces, and a 5 V automotive-grade supply domain. The device supports background debug mode (BDM) for non-intrusive in-circuit development. Technical depth: the HC908AS60A core implements an 8-bit accumulator-based ALU with stack pointer, index register H:X, and a status register. Program execution is fully static, allowing clock-stretching for low-power waits. The on-chip Flash uses a security feature that locks the debug port unless a password is supplied, protecting IP. The 8.4 MHz internal bus clock is derived from either an external crystal or an on-chip PLL/oscillator block. Typical applications include automotive body controllers, instrument cluster drivers, HVAC control modules, white-goods motor control, industrial sensor hubs, and CAN/LIN gateway nodes (when paired with external transceivers). The wide temperature range and 5 V I/O tolerance make the MC908AS60AMFU well suited to harsh environments. A key design consideration: at 5 V supply and high CPU utilization, the part draws noticeable quiescent current - budget for adequate PCB copper area if the application requires sustained high duty cycle at elevated ambient temperatures. The QFP-64 footprint also requires careful track fan-out to inner leads. This page synthesizes distributor stock/pricing, drop-in compatible alternatives from the HC908 family, and design notes that complement (not duplicate) the manufacturer's datasheet.

RFQ Liên hệ
MC908AZ32AVFUE - 8-Bit 8MHz 32KB Flash HC08 MCU | NXP
MC908AZ32AVFUE

MC908AZ32AVFUE - 8-Bit 8MHz 32KB Flash HC08 MCU | NXP

The NXP MC908AZ32AVFUE is an 8-bit HC08 family microcontroller IC running from the enhanced M68HC08 central processor unit (CPU08), with 32KB of on-chip FLASH, an integrated CAN controller, and 64-QFP (14x14) package for surface-mount automotive and industrial control boards. Background knowledge: An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH/ROM), data memory (RAM), and peripherals such as timers, ADC, communication ports (UART, SPI, I2C, CAN), and general-purpose I/O. The HC08 family from Freescale (now NXP) is a CISC 8-bit architecture widely used in automotive body, chassis, and industrial control applications because of its low cost, deterministic behavior, and broad peripheral set. Within the HC08 hierarchy, the AZ sub-family adds a CAN 2.0 A/B controller, making it well suited for in-vehicle networking nodes. Key features of the MC908AZ32AVFUE include 32KB (32K x 8) FLASH program memory, an 8MHz maximum bus clock, on-chip EEPROM for non-volatile configuration storage, an integrated MSCAN08 CAN 2.0 A/B controller, multiple timers, an 8-channel 8-bit ADC, and 16 general-purpose I/O pins. The 64-QFP (14x14) plastic package is a JEDEC-standard PQFP outline, providing a well-known surface-mount footprint for PCB designers. Operating voltage is 5V nominal and the device is specified over the automotive temperature grade per the Freescale datasheet. Architecturally, the CPU08 core provides a stack-based 8-bit ALU, 16-bit index register, H:X addressing, and a privileged BDC/SEC for in-circuit programming and debug. The MSCAN08 module implements CAN 2.0 A/B active/passive with bus-off recovery. Internal oscillator support and a low-power STOP/WAIT mode reduce quiescent current for battery-connected nodes. Typical applications include automotive body controllers, instrument clusters, HVAC control panels, industrial CAN sensor nodes, and appliance control boards. The integrated CAN interface removes the need for an external transceiver MCU pair for many nodes. Design consideration: when migrating from a similar HC08 AZ device (e.g., AZ60A), verify FLASH size and ADC channel count differences - the AZ32A carries 32KB FLASH, whereas the AZ60A doubles the program memory and adjusts the peripheral mix. Always check the latest PCN/errata before board respins. This page synthesizes distributor pricing, drop-in HC08AZ family alternatives, and practical design notes not found in the NXP datasheet.

RFQ Liên hệ