AAT1597-Q25-T - LCD White LED Backlight Driver | AAT
MPN: AAT1597-Q25-T ✓ Hoạt độngAAT1597-Q25-T Tóm tắt
A white-LED backlight driver (also called a constant-current boost converter for LEDs) is a power management IC that maintains a stable current through a series-connected LED chain by stepping up (boosting) the input voltage via an internal switch, inductor, and rectifying element. The category sits inside the broader LED driver hierarchy under power management, between low-side current sinks and full-display backlight controllers. White LEDs require constant current (not constant voltage) because luminous intensity is set by forward current, and headroom drops roughly 3.0 V per LED - making a boost topology mandatory when the input rail (often a single-cell Li-Ion at 3.0-4.2 V) cannot directly supply the string.
Key differentiating features of the AAT1597 include its integrated open-LED detection and short-circuit protection, single-wire PWM dimming, and an onboard power MOSFET optimized for up to 4 white LEDs. The device is targeted at small-format LCD backlights where board space, EMI cleanliness, and reliability are all critical constraints. AAT markets the part as a simple, economical, and compact solution for portable displays.
On the technical side, the AAT1597 uses a current-mode PWM control architecture with internal compensation, switching at roughly 1 MHz to allow tiny chip inductors and minimal input/output ripple. The boost switch integrates a low-RDS(on) N-channel MOSFET to maximize efficiency across the Li-Ion discharge curve, and feedback is taken via a sense resistor on the LED cathode side. Protection features include cycle-by-cycle current limit, over-temperature shutdown, and the previously mentioned open-LED protection.
Typical applications include LCD white-LED backlights in portable DVD/media players, handheld GPS units, industrial HMIs, point-of-sale terminals, and small medical displays. For designers, the most important trade-off is inductor selection - a 10 µH shielded type with low DCR is typical, and a 1 µF X7R ceramic output cap keeps ripple below LED flicker thresholds.
This page synthesizes distributor stock, parametric drop-in alternatives, and practical design notes that are not consolidated in any single manufacturer datasheet, giving engineers a single reference for evaluating the AAT1597-Q25-T against competing white-LED driver ICs.
Bộ thay thế dễ dàng lắp đặt cho AAT1597-Q25-T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AAT1597
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AAT1500
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AAT1597-Q25-T Tỷ lệ tối đa & tính chất điện
| Cấu trúc | Boost (step-up) converter |
| Chức năng | Constant-current LED driver for white LEDs |
| LED Configuration | Series string |
| Open-LED Protection | Yes (closes open LED to keep string operating) |
| PWM Dimming Input | Yes (dedicated PWM pin) |
| Kiểu lắp đặt | Surface Mount |
| Manufacturer | Advanced Analog Technology (AAT) |
| Protection Features | Open-LED, short-circuit, over-temperature |
Hướng dẫn cấu hình chân AAT1597-Q25-T standard
Cấu hình chân cho AAT1597-Q25-T (standard gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho AAT1597-Q25-T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AAT1597-Q25-T phù hợp cho 7 Áp dụngs: Portable DVD Player LCD Backlight, Handheld GPS / Navigation LCD Backlight, Industrial HMI Display Backlight, Point-of-Sale Terminal LCD Backlight, Small Medical Display Backlight, Automotive Rear-Seat Entertainment Display, IoT Sensor Display Backlight.
Portable DVD Player LCD Backlight
The AAT1597-Q25-T drives 2-4 series-connected white LEDs in the LCD backlight of portable DVD players, where board space is at a premium and a single-cell Li-Ion rail powers the entire system. The boost topology steps a 3.0-4.2 V Li-Ion input up to roughly 10-12 V to bias the LED string, while the integrated switch keeps the external BOM to just an inductor, input cap, output cap, and feedback resistor. The open-LED protection circuit keeps the picture visible even if one LED fails, which is critical for in-vehicle and airline entertainment where service is difficult. PWM dimming from the host MCU lets the firmware adjust brightness in response to ambient light.
Được đề xuất
Handheld GPS / Navigation LCD Backlight
The AAT1597-Q25-T is well matched to handheld GPS receivers that need uniform white-LED backlighting on a 3.5-4 inch LCD panel. The constant-current control maintains consistent luminance across the Li-Ion discharge curve (3.0 V to 4.2 V), preventing visible brightness drift as the battery drains. The PWM input connects directly to the GPS baseband or application processor, which dynamically reduces backlight current to extend runtime. Open-LED protection ensures the user still sees a usable screen during extended field use if a single LED degrades, an important reliability feature for outdoor/marine GPS products.
Được đề xuất
Industrial HMI Display Backlight
Industrial human-machine interface panels (HMI) need a wide-temperature, reliable white-LED backlight that survives 24/7 operation in factory environments. The AAT1597-Q25-T's integrated open-LED and over-temperature protection make it a defensible choice when the panel is sealed and unrepairable for years. The boost topology operates from 24 V or 12 V industrial rails down-converted to 5 V, then steps back up to bias the LED string. PWM dimming from the HMI controller allows day-shift and night-shift brightness profiles. The compact surface-mount footprint keeps the BOM small for cost-sensitive industrial displays.
Được đề xuất
Point-of-Sale Terminal LCD Backlight
POS terminals rely on a clear, flicker-free LCD backlight for clerks to read transactions and for customers to confirm amounts. The AAT1597-Q25-T's constant-current regulation and PWM dimming eliminate flicker artifacts that could be visible at low duty cycles, producing a stable backlight across the dimming range. The integrated switch reduces PCB area, leaving room for the touch controller and secure payment IC. Open-LED protection keeps the terminal operational even if one LED in the chain fails - critical for retail environments where downtime directly costs revenue.
Được đề xuất
Small Medical Display Backlight
Handheld medical devices - such as portable pulse oximeters, patient monitors, and diagnostic imagers - require stable, low-EMI backlighting to support clinical-grade display readability. The AAT1597-Q25-T's PWM dimming allows the firmware to step the backlight down during sleep to extend battery life on patient wearables. Constant-current control ensures the calibrated brightness does not drift as the Li-Ion battery discharges, preserving diagnostic display accuracy. Designers should still validate IEC 60601-1 EMI/ESD margins and review ISO 14971 risk files before integrating this driver into any medical device.
Được đề xuất
Automotive Rear-Seat Entertainment Display
The AAT1597-Q25-T is suitable for rear-seat entertainment (RSE) LCD panels in vehicles where the input is a 9-16 V automotive rail. The boost topology steps this rail down to a regulated 5 V intermediate, then back up to bias the LED string - but more importantly, the integrated protections (open-LED, short-circuit, over-temperature) cover the typical automotive failure modes. PWM dimming lets the head unit adjust brightness based on cabin ambient light. For full AEC-Q100 compliance on the design, pair this driver with an AEC-Q100-qualified companion MCU rather than relying on the AAT1597 alone.
Được đề xuất
IoT Sensor Display Backlight
Connected IoT devices with small status displays (thermostats, smart-home control hubs, sensor readouts) benefit from the AAT1597-Q25-T's small footprint and integrated switch, which keeps the BOM cost below USD 1 for the entire power section. The PWM dimming interface lets the host MCU pulse the backlight on only when the user approaches, dramatically reducing average power. Open-LED protection ensures the user-facing display never goes completely dark in a service call. For battery-powered IoT, the boost topology efficiently produces the 9-12 V LED bias from a 3.3 V coin-cell or Li-Ion supply.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AAT1597-Q25-T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AAT1597 | AAT1500 |
|---|---|---|---|
| Brand | Advanced Analog Technology (AAT) | Advanced Analog Technology (AAT) | Advanced Analog Technology (AAT) |
| Package | QFN/TSOP (Q25 outline) | QFN/TSOP (Q25 outline) - same | QFN/TSOP - same family |
| Topology | Boost (constant current) | Boost (constant current) | Boost (constant current) |
| Number of LEDs Supported | Up to 4 white LEDs (series) | Up to 4 white LEDs (series) | 1 to 4 white LEDs |
| Integrated Switch | — | Yes | Yes |
Bảo phân biệt quan trọng
- Integrated open-LED protection that bypasses a failed LED segment (vsAAT1500)
- Dedicated single-wire PWM dimming pin (vsAAT1500)
- Optimized for 4-LED LCD backlight with internal switch (vsDiscrete boost + external FET designs)
Ghi chú thiết kế
Place the boost inductor, input capacitor, output capacitor, and feedback resistor as close as possible to the IC pins to minimize switching-noise radiation and loop-area-induced ringing. Use a 10 µH shielded inductor with low DCR (~0.1 Ω or below) to maximize efficiency and reduce thermal rise. The output capacitor should be a 1 µF X7R ceramic rated for the maximum LED-string voltage to keep ripple low and prevent visible flicker. Estimated: at 100 mA LED current and 1 MHz switching, output ripple is dominated by ESR of the output capacitor - X7R 1 µF in 0805 keeps ripple below 50 mV.
At full 4-LED load and worst-case input voltage, the internal switch dissipates noticeable power that must be conducted out through the PCB copper pour and exposed thermal pad. Provide at least 0.25 square inches of 2-oz copper tied to the exposed pad to keep junction temperature rise below 30 °C above ambient. In sealed enclosures with no airflow, derate LED current to 60-70 % of nominal. Estimated: at 4 white LEDs (12 V VOUT), 20 mA each, and 4.2 V VIN, switch dissipation is approximately 0.4 W continuous.
Do not exceed the absolute maximum LED string voltage; otherwise the internal MOSFET will avalanche and the part will be permanently damaged. Always populate the feedback resistor (R1) using 1 % tolerance to maintain accurate LED current. The PWM dimming pin should not be left floating - tie to GND with a 100 kΩ resistor if unused to prevent accidental full-brightness turn-on at power-up. Estimated: at 20 mA LED current with R1 = 75 Ω, the FB regulation voltage is typically 0.6 V.
Thông tin tuân thủ
RoHS and lead-free status per public AAT product page; REACH, halogen-free, and conflict-minerals declarations not present in the indexed web data and require confirmation from the manufacturer.
