AD7492AR-5 - 12-Bit 1.25 MSPS ADC | Analog Devices
MPN: AD7492AR-5 ✓ Hoạt độngAD7492AR-5 Tóm tắt
An ADC is a data-conversion semiconductor that converts a continuous analog voltage into a digital code. The AD7492 belongs to the successive-approximation ADC family, commonly called a SAR ADC, within the broader analog-to-digital converter and data-converter IC hierarchy. Its parallel interface presents each 12-bit conversion result across dedicated output lines, making it suitable for systems that can capture and process a result rapidly after conversion.
The AD7492 family combines resolution, throughput, and low power in a compact surface-mount package. Key characteristics include 12-bit conversion resolution, throughput up to 1.25 MSPS, one analog input, a parallel word-access interface, and operation from one 2.7 V to 5.25 V supply. The -5 suffix identifies the 1.25 MSPS member of the AD7492 family, while AD7492AR uses the 24-lead SOIC option represented by the R package code.
Internally, the converter uses successive-approximation conversion, progressively refining the sampled analog voltage into a 12-bit digital result. An integrated reference and clock reduce the number of external support components required for basic operation. Because the converter uses a parallel data interface, the PCB must route 12 data lines in addition to control and power signals, making pin assignment and signal-integrity layout important at the board level.
Typical applications include industrial process control, instrumentation, sensor acquisition, communications equipment, and embedded measurement systems. It is particularly appropriate when a system requires moderate resolution, sampling rates up to 1.25 MSPS, and a direct parallel interface rather than a serial protocol such as SPI or I2C.
The principal design considerations are source impedance, input settling time, reference behavior, digital-output timing, and supply decoupling. Place input and bypass capacitors close to the relevant device pins, use short digital traces, and maintain the required acquisition interval so the sampled input settles before conversion begins.
This page combines the AD7492AR-5 device specifications, a practical replacement assessment, package-level design guidance, and application-focused selection criteria to support faster engineering decisions beyond a basic catalog listing.
Bộ thay thế dễ dàng lắp đặt cho AD7492AR-5 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD7492AR-5 (cùng hình factor và footprint) — khác nhau ở Data Interface, Number of Input Channels, Package, Power Consumption, Resolution.
AD7492ARUZ-5-REEL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD7492ARUZ-5-REEL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD7492AR-5 Tỷ lệ tối đa & tính chất điện
| ADC Type | Successive-approximation ADC |
| Độ phân giải | 12 bit |
| Maximum Throughput | 1.25 MSPS |
| Number of Input Channels | 1 channel |
| Input Supply Voltage Range | 2.7 V to 5.25 V |
| Data Interface | Parallel word access |
| Integrated Reference | Internal reference |
| Integrated Clock | Internal clock |
| Hộp | 24-lead SOIC, 0.295 inch body width |
| Kiểu lắp đặt | Surface mount |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Power Consumption | 16 mW |
| Input Type | Single-ended analog input |
| Output Word Width | 12 bit |
Hướng dẫn cấu hình chân AD7492AR-5 24-lead soic, 0.295 inch body width
Cấu hình chân cho AD7492AR-5 (24-lead soic, 0.295 inch body width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD7492AR-5.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD7492AR-5 phù hợp cho 6 Áp dụngs: Industrial Process Measurement, Sensor Signal Acquisition, Communications Receiver, Test and Measurement Equipment, Data Acquisition Module, Power and System Monitoring.
Industrial Process Measurement
The AD7492AR-5 is appropriate for acquiring pressure, temperature, level, or current-loop signals in industrial measurement systems because it combines 12-bit resolution with throughput up to 1.25 MSPS. A frontend can condition the sensor output to the ADC input range, while the single 2.7 V to 5.25 V supply simplifies system power distribution. The parallel interface permits direct connection to FPGA or digital logic without requiring a serial protocol. The main design requirement is to verify that the sensor amplifier and protection network settle completely during the available acquisition interval, especially when the target sampling rate is close to 1.25 MSPS.
Được đề xuất
Sensor Signal Acquisition
The AD7492AR-5 can digitize outputs from bridge amplifiers, current-to-voltage converters, and other sensor front ends when moderate resolution and rapid sampling are needed. Its 1.25 MSPS maximum rate supports periodic monitoring without requiring a high-speed serial ADC. Place the analog input path close to the converter, return analog ground beneath the input network, and bypass the supply close to the device pins. Confirm the source impedance against the manufacturer's acquisition requirements so that the sampled voltage has sufficient settling time before each successive-approximation conversion begins.
Được đề xuất
Communications Receiver
The AD7492AR-5 is suitable for receiver-envelope, received-level, or baseband monitoring circuits that require frequent conversion of a single analog channel. Its 12-bit code width provides 4096 discrete levels, while the parallel output can feed an FPGA capture block or communications controller. The 1.25 MSPS rate gives an 800 ns theoretical conversion period, which supports periodic sampling but requires deterministic control of the conversion-complete signal. Keep the 12 output traces short, avoid unnecessary branch stubs, and confirm output timing against the receiving logic before finalizing the layout.
Được đề xuất
Test and Measurement Equipment
The AD7492AR-5 can serve as a measurement ADC in compact instrumentation that samples a conditioned input and transfers each 12-bit result to digital logic. Its single-channel architecture and parallel output make it appropriate for controlled laboratory or service equipment rather than a simultaneous multichannel scanner. Designers should budget settling time for the input filter, use a low-noise reference arrangement, and isolate analog and digital return currents. At the maximum 1.25 MSPS rate, timing verification should include conversion duration, acquisition interval, output propagation delay, and controller capture margin.
Được đề xuất
Data Acquisition Module
The AD7492AR-5 is a compact ADC for small data-acquisition modules that must return a 12-bit result to an FPGA, microcontroller, or parallel capture logic. Its 24-lead SOIC package keeps the converter footprint manageable, while the internal reference and clock reduce external support complexity for basic designs. Parallel routing does require more PCB space than a serial interface and careful planning of the 12-bit bus. Use a solid ground plane, place decoupling capacitors at the supply pins, and assign the conversion-status signal to timing-critical routing ahead of the data bus.
Được đề xuất
Power and System Monitoring
The AD7492AR-5 can monitor a scaled representation of a power rail, battery voltage, or another slow-changing system signal where 12-bit resolution is useful. The single 2.7 V to 5.25 V supply allows operation across common embedded voltage ranges, and the integrated reference and clock simplify standalone monitoring. Although the converter supports 1.25 MSPS, most monitoring functions require far lower rates, so designers should use a sampling interval that avoids unnecessary switching activity and provides ample input-settling time. Protection, filtering, and resistor selection must keep the analog input within its permitted range.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD7492AR-5 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD7492AR | AD7492ARUZ-5 |
|---|---|---|---|
| Package | 24-lead SOIC, 0.295 inch body width | 24-lead SOIC | 24-lead SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| ADC Architecture | Successive approximation | Successive approximation | Successive approximation |
| Resolution | 12 bit | 12 bit | 12 bit |
| Maximum Throughput | 1.25 MSPS | 1 MSPS | 1.25 MSPS |
| Input Channels | 1 channel | 1 channel | 1 channel |
| Supply Voltage | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Data Interface | 12-bit parallel | 12-bit parallel | 12-bit parallel |
| Reference and Clock | Integrated reference and clock | Integrated reference and clock | Integrated reference and clock |
Bảo phân biệt quan trọng
- Higher listed sampling throughput within the same AD7492 family (vsAD7492AR)
- Exact 1.25 MSPS family member with matched package technology (vsAD7492ARUZ-5)
- Parallel output supports direct digital capture (vsAD7492AR)
Ghi chú thiết kế
Route the 12-bit parallel data bus as a short, continuous group and match output-to-output trace lengths where the receiving device does not tolerate skew. Place the conversion-status signal close to the destination capture logic and avoid long stubs on data lines. Because the AD7492AR-5 supports 1.25 MSPS, establish setup and hold margins using the manufacturer timing definitions rather than relying only on clock frequency.
Place supply-bypass capacitors immediately beside the power and ground pins, with a short ground return to the device. Keep the analog input route short and isolated from digital output and clock-return paths. A continuous ground plane is preferable to fragmented plane regions, and the input filter should be located near the ADC so that its resistance, capacitance, leakage, and settling behavior can be evaluated at the conversion rate.
Do not assume that identical package dimensions guarantee a drop-in substitution. The AD7492AR has a lower listed throughput of 1 MSPS than the 1.25 MSPS AD7492AR-5, so check acquisition and sampling deadlines. Also verify every power, reference, clock, control, and digital-output connection against the manufacturer pin-description table for the exact ordering suffix before releasing a replacement PCB.
Use a low-impedance 2.7 V to 5.25 V supply and decouple close to the device. The listed 16 mW figure describes the internal reference and clock function, not the complete board-level power budget. Calculate total consumption from the conversion rate, digital output state, supply voltage, and any external clock arrangement. Ensure the source can support transient demand without coupling conversion activity into the sensitive analog input path.
Thông tin tuân thủ
The AD7492 is an industrial analog-to-digital converter rather than an automotive-qualified device. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code.