AD9731BRS - 10-Bit 170 MSPS Bipolar DAC | Analog Devices
MPN: AD9731BRS ✓ Hoạt độngAD9731BRS Tóm tắt
A DAC is a data converter that transforms parallel or serial digital codes into a proportional analog output. A bipolar DAC produces positive and negative output currents, making it suitable for systems that require symmetric signal swings around a central bias point. Within the semiconductor hierarchy, the AD9731BRS is a data-converter IC, a mixed-signal IC, and ultimately a semiconductor component used to generate controlled analog waveforms for communications equipment.
The AD9731 emphasizes dynamic performance for demanding communication links. Its 170 MSPS update rate supports high-bandwidth waveform generation, while the 10-bit architecture balances output resolution with implementation complexity. The device was positioned as a lower-power and more economical alternative to earlier high-performance bipolar DAC solutions. This combination makes it relevant to transmitters, signal generators, digital synthesis systems, and test equipment that must create wideband analog signals from digital data.
The AD9731 is available in 28-lead SOIC and space-saving 28-lead SSOP configurations, with the AD9731BRS ordering code associated with the compact surface-mount implementation. The datasheet states that supply voltages should remain within ±5% of nominal for proper operation. That tolerance directly affects output-current accuracy, so a stable low-noise supply and proper bypassing remain central to achieving predictable converter performance.
Typical applications include digital communications transmitters, arbitrary waveform generators, RF and microwave signal-chain excitation, radar test systems, and high-speed industrial instrumentation. In these systems, the AD9731BRS acts as the final digital-to-analog conversion stage, converting an upstream sample stream into a bipolar analog current. Clocking, digital data alignment, output reconstruction filtering, and downstream amplification determine how effectively the converter's dynamic performance reaches the end user.
Designers should preserve the datasheet-specified supply tolerances, provide clean digital and analog return paths, and place decoupling capacitors close to the supply pins. Because the converter output is a current, an output buffer or amplifier is normally required to convert that current into a usable voltage. Component tolerances, clock jitter, and reconstruction-filter performance can limit system-level results even when the DAC itself operates within specification.
This page organizes the AD9731BRS architecture, package information, application guidance, and engineering trade-offs in one place. It also distinguishes verified device characteristics from parameters that require confirmation from the manufacturer datasheet, helping engineers plan sourcing and design reviews without relying on ambiguous catalog summaries.
Bộ thay thế dễ dàng lắp đặt cho AD9731BRS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD9731S
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD9731
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD9731BRSZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD9731BRUZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD9731BRS Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 10 bit |
| Maximum Update Rate | 170 MSPS |
| Converter Type | Bipolar current-output D/A converter |
| Output Architecture | Bipolar differential current output |
| Hộp | 28-lead SSOP |
| Kiểu lắp đặt | Surface mount |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Supply Voltage Tolerance | ±5% of nominal |
Hướng dẫn cấu hình chân AD9731BRS 28-lead ssop
Cấu hình chân cho AD9731BRS (28-lead ssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD9731BRS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD9731BRS phù hợp cho 6 Áp dụngs: Communications Transmitter Signal Generation, Arbitrary Waveform Generation, RF and Microwave Test-Signal Excitation, Digital Radar and Baseband Modulation, High-Speed Industrial Instrumentation, Digital-to-Analog Signal-Chase Prototyping.
Communications Transmitter Signal Generation
The AD9731BRS suits the final conversion stage of a communications transmitter because it combines a 10-bit data interface with a 170 MSPS update rate and a bipolar current output. Digital sample data from a field-programmable logic or digital signal-processing stage can be converted into a differential analog waveform for subsequent amplification and filtering. The AD9731 family was developed for demanding communications systems with wideband spurious-free dynamic range requirements. Keep the clock and data traces short, control clock jitter, and place the reconstruction network close to the converter to preserve wideband behavior. The external output network and buffer must be designed around the AD9731 datasheet pin description and recommended application circuit.
Được đề xuất
Arbitrary Waveform Generation
A 170 MSPS update rate makes the AD9731BRS applicable to arbitrary waveform generators and digital waveform synthesis systems. The converter accepts 10-bit digital samples and produces a bipolar current that can be transformed into a symmetrical voltage by a current-to-voltage buffer. This architecture is useful when a laboratory instrument must reproduce precomputed digital waveforms. The AD9731 datasheet identifies the converter as optimized for high dynamic performance rather than maximum output resolution, so waveform quality depends on the clock source, digital data integrity, reconstruction filter, and output-buffer bandwidth. Use the manufacturer reference circuit as the starting point for component values and termination arrangements.
Được đề xuất
RF and Microwave Test-Signal Excitation
The AD9731BRS can generate wideband bipolar test signals for RF, microwave, and radar test equipment. The 170 MSPS sampling rate creates a high analog bandwidth ceiling, while the 10-bit word length gives adequate resolution for many excitation waveforms after filtering. A typical implementation converts a stored or computed digital sequence into an analog signal, applies reconstruction filtering, and then feeds downstream mixer or measurement hardware. Dynamic performance depends on keeping jitter low and preventing digital switching energy from coupling into the output path. Place output filtering near the DAC and isolate sensitive analog stages with appropriate return-path planning.
Được đề xuất
Digital Radar and Baseband Modulation
The AD9731BRS fits baseband waveform generation for digital radar, electronic instrumentation, and modulation systems. A 170 MSPS update rate supports high-speed complex envelopes when paired with suitable digital synthesis logic, and the bipolar current output supports balanced analog signal chains. Designers should treat clock timing and reconstruction-filter attenuation as part of the converter design rather than as separate concerns. The AD9731 datasheet requires supply voltages to remain within ±5% of nominal, making supply regulation an important contributor to output-current accuracy. Validate the complete data path and analog output against the manufacturer evaluation-circuit arrangement before production release.
Được đề xuất
High-Speed Industrial Instrumentation
The AD9731BRS can serve as the waveform-producing element in high-speed industrial instrumentation that generates controlled analog stimuli for testing sensors, converters, or signal-processing modules. Its 10-bit resolution and 170 MSPS update rate are well matched to systems requiring multimegahertz-class output sequences rather than laboratory-level DC precision. The bipolar output allows symmetric drive into downstream circuitry and can simplify the design of balanced amplifiers. Because the device operates from -40°C to +85°C, it also supports extended industrial environments where temperature stability and supply regulation are controlled. Confirm output-current accuracy and settling behavior in the Analog Devices datasheet for the operating conditions of the instrument.
Được đề xuất
Digital-to-Analog Signal-Chase Prototyping
The AD9731BRS is useful in prototype signal-chain boards where a designer needs a fast bipolar DAC stage to evaluate filtering, amplification, or modulation behavior. Its 28-lead SSOP form factor simplifies assembly on a conventional surface-mount prototype board compared with a fine-pitch leaded package. The 170 MSPS rate enables rapid evaluation of high-bandwidth digital sequences, while the 10-bit resolution provides a practical balance between spectral performance and implementation effort. Use short, controlled-impedance digital routes, separate analog return paths, and a low-noise output stage. The datasheet application information should determine output-network values and supply-bypass placement.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD9731BRS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Resolution | 10 bit |
| Maximum Update Rate | 170 MSPS |
| Output Architecture | Bipolar current output |
| Package | 28-lead SSOP |
| Brand | Analog Devices |
| Operating Temperature Range | -40°C to +85°C |
| Supply Voltage Tolerance | ±5% of nominal |
| Mounting Type | Surface mount |
| Target Application | High-speed communications and signal generation |
Bảo phân biệt quan trọng
- High-speed conversion combined with bipolar current output (vsNo verified drop-in alternative MPN)
- Space-saving surface-mount implementation (vsAD9731 28-lead SOIC configuration)
- Extended industrial temperature operation (vsCommercial-temperature DAC alternatives)
Ghi chú thiết kế
Keep every supply rail within ±5% of nominal, as specified in the Analog Devices AD9731 datasheet, and place high-frequency bypass capacitors close to the device pins. Because supply variation influences the DAC reference and output-current accuracy, regulated rails with low ripple are preferable to loosely filtered sources. Route the analog and digital grounds toward their intended return points without sharing noisy high-current paths.
Treat clock quality and data-bus timing as part of the converter design. A low-jitter clock is essential when generating wideband waveforms at 170 MSPS, and the digital input lines should be short, properly terminated, and routed away from the analog output network. Validate eye margin and board-level spurious performance with the intended clock source because the converter specification alone cannot account for PCB skew, reflections, or jitter.
The AD9731BRS produces a bipolar current, so place the reconstruction network and any output-buffer interface close to the converter. Use the manufacturer application circuit as the basis for differential output routing and component values. Keep digital switching nodes over continuous return planes, maintain symmetrical analog routing where possible, and avoid routing clock signals beneath sensitive output components.
Do not assume that a converter with the same nominal sample rate can replace the AD9731BRS. A true drop-in alternative must match the 28-lead pinout, digital interface behavior, bipolar output network, supply arrangement, and timing characteristics. The AD9731 family also exists in a 28-lead SOIC configuration, so verify the physical package and pin mapping rather than relying only on the family name or resolution.
Thông tin tuân thủ
The Analog Devices product materials reviewed for this record do not state RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals status. Request current compliance documentation through the Request a Quote form when a formal declaration is required.