AD977BNZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
MPN: AD977BNZ ✓ Hoạt độngAD977BNZ Tóm tắt
An ADC is a data-conversion IC that converts an analog voltage into a digital code for processing by a microcontroller, DSP, or other digital system. The AD977 belongs to the SAR ADC family within the broader analog-to-digital converter and data-converter hierarchy. SAR conversion repeatedly compares the sampled input with an internally generated reference to determine successive bits of the 16-bit result.
Key features include 16-bit resolution, a 100 kSPS throughput rate, one analog input channel, a serial SPI interface, and single 5 V operation. Maximum power dissipation is 100 mW, while a dedicated power-down mode helps reduce consumption when conversions are not required. The converter is housed in a 20-pin PDIP package measuring approximately 0.300 inches wide, or 7.62 mm.
The AD977 uses a switched-capacitor successive-approximation architecture and includes an internal 2.5 V reference. Its serial interface reduces the number of signal connections compared with a parallel-output ADC, making the device suitable for space-constrained instrumentation where conversion rate requirements are below 100 kSPS. The analog input remains single-ended according to the product specifications.
Typical applications include industrial process measurement, sensor signal acquisition, laboratory instrumentation, factory automation, and embedded control systems. These uses benefit from the combination of 16-bit resolution, serial connectivity, and a moderate conversion rate rather than the very high throughput required by waveform capture or communications receivers.
When designing around the AD977BNZ, preserve adequate input-headroom margin for the full 4.75 V to 5.25 V supply range and follow the manufacturer's grounding and reference recommendations. Confirm that 100 kSPS meets the application's acquisition rate and allow for acquisition, conversion, and serial-transfer time when calculating end-to-end throughput.
This product page combines the AD977BNZ electrical characteristics, package information, replacement analysis, and practical design guidance to help engineers evaluate the converter before integrating it into a new analog measurement system.
Bộ thay thế dễ dàng lắp đặt cho AD977BNZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD977BNZ (cùng hình factor và footprint) — khác nhau ở Power-Down Mode.
AD977BN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD977BNZ Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 16 bit |
| Conversion Architecture | Successive approximation register (SAR) |
| Tỷ lệ lấy mẫu | 100 kSPS |
| Number of Input Channels | 1 channel |
| Input Type | Single input |
| Data Interface | Serial SPI-compatible interface |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Internal Reference Voltage | 2.5 V |
| Maximum Power Dissipation | 100 mW |
| Power-Down Mode | Supported |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Package Type | 20-pin PDIP |
| Package Width | 0.300 inch (7.62 mm) |
| Kiểu lắp đặt | Through-hole PDIP |
| Packaging | Tube |
Hướng dẫn cấu hình chân AD977BNZ 0.300 inch (7.62 mm)
Cấu hình chân cho AD977BNZ (0.300 inch (7.62 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD977BNZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD977BNZ phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Process Control Loops, Laboratory Instrumentation, Factory Automation Controllers, Embedded Environmental Monitoring, Audio and Communication Control.
Industrial Sensor Acquisition
The AD977BNZ suits sensor acquisition systems that require 16-bit measurement resolution but operate below 100 kSPS. Its single analog input and serial SPI-compatible interface reduce the number of interconnections compared with a parallel-output converter, which is useful in compact sensor interface boards. According to the AD977 datasheet, the converter operates from 4.75 V to 5.25 V and includes an internal 2.5 V reference. The analog front end should provide enough acquisition and settling time to satisfy the ADC's sampling requirements.
Được đề xuất
Process Control Loops
AD977BNZ can digitize pressure, temperature, level, and flow signals in industrial process-control equipment where a moderate sampling rate is sufficient. Its 16-bit output provides 65,536 numerical codes, while the 100 kSPS throughput supports frequent loop updates. According to Analog Devices product documentation, the device has one analog input, a serial interface, and a single 5 V supply. Design the input conditioning, protection, and grounding so sensor transients and supply noise do not compromise the measured code.
Được đề xuất
Laboratory Instrumentation
The AD977BNZ is appropriate for bench instruments that measure relatively slow analog signals and require more resolution than a basic control ADC. Its serial interface simplifies connection to an embedded controller, while the 20-pin PDIP package is convenient for through-hole laboratory prototypes. According to the AD977 datasheet, maximum power dissipation is 100 mW and the operating-temperature range extends from -40°C to +85°C. The instrument should still provide clean grounding, stable excitation, and a suitable analog input range.
Được đề xuất
Factory Automation Controllers
AD977BNZ can serve as the measurement converter in factory automation equipment that reads slowly changing analog process conditions. The 100 kSPS rate is well suited to periodic sensor polling, and the single-input serial architecture supports a compact controller PCB. According to the AD977 datasheet, the ADC operates from a single 5 V supply and provides a power-down mode for inactive periods. Choose external filtering and input protection appropriate to the industrial wiring environment.
Được đề xuất
Embedded Environmental Monitoring
The AD977BNZ can digitize outputs from environmental, gas, and position sensors in a compact monitoring node. Its 16-bit code width and 100 kSPS throughput permit periodic measurements without the overhead of a high-speed waveform converter, while serial communication fits embedded systems. According to Analog Devices documentation, the converter includes an internal 2.5 V reference and accepts a 4.75 V to 5.25 V supply. Calibrate the sensor chain and account for reference and analog-path error during long-term measurements.
Được đề xuất
Audio and Communication Control
AD977BNZ can be evaluated for supervisory control, bias monitoring, or slow auxiliary signal acquisition within audio and communication equipment. Its 100 kSPS throughput is sufficient for many supervisory channels but not for full-bandwidth audio capture. According to the AD977 datasheet, the serial interface helps minimize wiring in a dense control assembly and the power-down mode can reduce activity during idle periods. The converter should be isolated from high-energy signal paths and supplied from a suitably quiet rail.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD977BNZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD977BN |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 20-pin PDIP | 20-pin PDIP - same package |
| Resolution | 16 bit | 16 bit |
| Sampling Rate | 100 kSPS | 100 kSPS |
| Input Channels | 1 channel | 1 channel |
| Conversion Architecture | SAR | SAR |
| Supply Voltage | 4.75 V to 5.25 V | 5 V single supply |
| Data Interface | Serial SPI-compatible | Serial interface |
| Internal Reference | 2.5 V | 2.5 V |
Bảo phân biệt quan trọng
- Maintains the documented 16-bit conversion resolution (vsAD977BN)
- Preserves the same 100 kSPS throughput class (vsAD977BN)
- Uses the same 20-pin PDIP physical format (vsAD977BN)
Ghi chú thiết kế
Follow the AD977 datasheet pin-description table when assigning the 20 PDIP nets and preserve the converter's recommended grounding arrangement. Keep the analog input trace short, place input-conditioning components close to the relevant pins, and route digital control and serial-data signals away from sensitive input paths. The package is a through-hole PDIP format, so check component spacing, connector orientation, and available board area before finalizing the mechanical layout.
Design the 5 V supply so it remains within the specified 4.75 V to 5.25 V range during startup, load changes, and temperature operation. Place the bypass capacitors specified by the manufacturer close to the supply and ground pins, and verify startup behavior before enabling repeated conversions. The power-down mode can reduce activity when continuous acquisition is unnecessary, but its effect on output validity and serial timing should be checked in firmware.
Account for acquisition time, input-settling time, conversion time, and serial-transfer time when determining real throughput. The published 100 kSPS specification should not be interpreted as permission to start every new sample before the previous conversion and acquisition have completed. Use the manufacturer's timing diagram to define control and data-valid behavior, and avoid driving the serial bus from multiple devices unless the interface arrangement explicitly supports it.
Do not select AD977BNZ solely by resolution and sampling rate. Confirm the analog input range, reference arrangement, serial timing, and 20-pin PDIP pin assignments in the manufacturer datasheet before schematic capture. Also verify that the AD977BN replacement is acceptable for the intended temperature grade and production configuration. The internal 2.5 V reference does not eliminate the need to keep the analog input within its supported voltage range.
Thông tin tuân thủ
The AD977BNZ is an industrial-temperature analog converter. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the product information, so those statuses remain unknown. AEC-Q100 qualification is not identified and is not applicable to the published industrial configuration.