AD977CNZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
MPN: AD977CNZ ✓ Hoạt độngAD977CNZ Tóm tắt
An ADC converts an analog input voltage into a digital code for measurement, control, recording, or signal processing. The AD977 belongs to the successive-approximation ADC family within the broader ADC/DAC and data-converter hierarchy. Its SAR architecture repeatedly compares the sampled input with a internally generated reference, making it suitable for applications requiring accurate conversion without the complexity of flash conversion.
Key specifications include 16-bit resolution, one analog input, a 100 kSPS sampling rate, and operation from a single 5 V rail. Maximum power dissipation is 100 mW, supporting low-power acquisition systems. The supported operating-temperature range is -40°C to 85°C, while the 20-PDIP package is supplied in a tube for through-hole PCB assembly.
Internally, the AD977 combines a switched-capacitor ADC, a 2.5 V internal reference, and a high-speed serial interface. Factory calibration minimizes offset, gain, and linearity errors, while listed AC testing includes signal-to-noise ratio and total harmonic distortion performance. The AD977 family provides 100 kSPS throughput, whereas the related AD977A family provides 200 kSPS.
Typical uses include industrial process measurement, instrumentation, laboratory data acquisition, audio and low-frequency waveform sampling, sensor-interface systems, and embedded control platforms. The 100 kSPS rate is appropriate for acquiring slowly changing or moderate-bandwidth analog signals rather than high-frequency communications waveforms.
Designers should provide a stable 5 V supply, observe the analog and reference grounding requirements, and validate input range and acquisition timing against the manufacturer datasheet. Because the serial interface, reference behavior, conversion timing, and digital signaling remain important to system accuracy, firmware and PCB validation should be completed before production release.
This product page consolidates verified manufacturer and distributor specifications, package details, availability references, and selection guidance. It also distinguishes the AD977CNZ from the faster AD977A family and clearly identifies where equivalent drop-in replacement data was not established by the supplied cross-reference evidence.
Bộ thay thế dễ dàng lắp đặt cho AD977CNZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD977ANZ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →AD977CNZ Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 16 bit |
| Input Count | 1 input |
| Architecture | Successive approximation (SAR) |
| Throughput Rate | 100 kSPS |
| Điện áp cung cấp | 5 V |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Internal Reference Voltage | 2.5 V |
| Maximum Power Dissipation | 100 mW |
| Khoảng nhiệt độ hoạt động | -40°C to 85°C |
| Data Interface | Serial SPI |
| Hộp | 20-PDIP (0.300 inch, 7.62 mm) |
| Kiểu lắp đặt | Through-hole |
| Packaging | Tube |
| Calibration | Factory calibrated |
| DC and AC Performance | Offset, gain, linearity, SNR, and THD tested |
| Analog Supply | Single 5 V operation |
Hướng dẫn cấu hình chân AD977CNZ 20-pdip (0.300 inch, 7.62 mm)
Cấu hình chân cho AD977CNZ (20-pdip (0.300 inch, 7.62 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD977CNZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD977CNZ phù hợp cho 6 Áp dụngs: Industrial Process Measurement, Laboratory Data Acquisition, Audio and Waveform Sampling, Sensor Interface Systems, Embedded Control and Monitoring, Power and Equipment Monitoring.
Industrial Process Measurement
The AD977CNZ fits industrial process-monitoring systems that convert slowly changing pressure, temperature, or level signals into 16-bit digital measurements. Its 100 kSPS throughput provides more than adequate conversion bandwidth for many sensor-conditioning systems, while the single 5 V supply simplifies power architecture. The internal 2.5 V reference supports repeatable operation without an external reference circuit. Engineers should still account for sensor excitation, common-mode voltage, protection networks, grounding, and calibration when connecting industrial transducer outputs.
Laboratory Data Acquisition
The AD977CNZ is appropriate for laboratory and benchtop measurement systems that prioritize resolution and predictable serial data transfer over maximum conversion speed. Its 16-bit SAR architecture samples at 100 kSPS, providing ample bandwidth for many general-purpose analog channels, while maximum power dissipation is limited to 100 mW. The 20-PDIP through-hole package simplifies insertion into prototype boards. Firmware must implement the documented serial interface timing and correctly handle conversion latency and data-valid signaling.
Audio and Waveform Sampling
The AD977CNZ can be used for low-frequency audio, control, and waveform acquisition where the required bandwidth fits within its 100 kSPS throughput. The 16-bit resolution provides substantially more code levels than an 8-bit converter and can improve measurement fidelity when the analog front end is properly conditioned. Factory calibration addresses offset, gain, and linearity errors, while SNR and THD are among the tested performance characteristics. Aliasing, input bandwidth, settling time, and digital reconstruction must still be managed at the system level.
Sensor Interface Systems
The AD977CNZ is suitable for digitizing outputs from bridge, potentiometric, and low-bandwidth transducer front ends. Its single-input architecture makes it appropriate for dedicated measurement channels rather than simultaneous multi-channel acquisition without external multiplexing. The 5 V operating supply and internal 2.5 V reference simplify system partitioning, and the 100 kSPS rate supports rapid conversion in many control loops. The analog input must remain within the manufacturer-specified range, and excitation drift and ground potentials require careful PCB treatment.
Embedded Control and Monitoring
The AD977CNZ suits embedded monitoring controllers that need higher-resolution analog measurements than a low-cost internal controller ADC may provide. A 100 kSPS conversion rate allows the controller to sample several slow control or diagnostic channels through multiplexing if required. The serial interface is appropriate for communication with a microcontroller or digital controller, while the 20-PDIP package is useful where a through-hole prototype or serviceable module is preferred. Software should include range checks, saturation handling, and conversion-status synchronization.
Power and Equipment Monitoring
The AD977CNZ can serve as the measurement converter in equipment that monitors slow power-system variables, battery states, or analog subsystem health. Its 16-bit resolution can preserve small changes in a conditioned voltage, and the 100 kSPS rate supports event monitoring and closed-loop updates. The converter's 100 mW maximum power dissipation helps limit its impact on the monitored system. Accurate results still depend on a stable 5 V source, suitable input conditioning, calibrated scaling, and isolation where the monitored node presents a high common-mode voltage.
Dữ liệu tham khảo kỹ thuật cho AD977CNZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD977ANZ |
|---|---|---|
| Package | 20-PDIP (0.300 inch, 7.62 mm) | 20-PDIP (0.300 inch, 7.62 mm) |
| Brand | Analog Devices | Analog Devices |
| Resolution | 16 bit | 16 bit |
| Throughput Rate | 100 kSPS | 200 kSPS |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) |
| Input Count | 1 input | 1 input |
| Supply Voltage | 5 V | 5 V |
| Internal Reference | 2.5 V | 2.5 V |
Bảo phân biệt quan trọng
- Lower throughput than the AD977A family (vsAD977ANZ)
- Match to the original 20-PDIP supply chain (vsAD977ANZ)
- Lower power ceiling (vsAD977ANZ)
Ghi chú thiết kế
Power the AD977CNZ from a stable single 5 V rail within the documented 4.75 V to 5.25 V range. Place the recommended bypass capacitors close to the supply pins and keep analog return current separate from noisy digital return paths. The converter's maximum dissipation is 100 mW, but usable system performance still depends on supply-noise rejection, grounding, reference stability, and adequate headroom for the analog input.
Route the analog input away from digital clock and serial-interface traces, and use a compact, guarded layout around the converter. Treat the internal 2.5 V reference and analog signal path as sensitive nodes, minimize loop area, and provide a low-impedance ground connection. For the 20-PDIP implementation, observe the manufacturer's pin orientation and avoid long parallel runs between adjacent digital outputs and the analog input.
Do not interpret a 100 kSPS throughput specification as unlimited input bandwidth. The input must remain within the specified range, and sampling at 100 kSPS requires appropriate anti-aliasing behavior for the signal bandwidth. Firmware must also follow the documented conversion latency, data-valid timing, and serial clock requirements; incorrect read timing can create apparently random or duplicated codes.
Thông tin tuân thủ
The supplied verified data does not contain explicit compliance declarations for AD977CNZ. No RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was inferred.
