ADM211EAR - 5V RS-232 Transceiver, 28-SOIC | Analog Devices
MPN: ADM211EAR ✓ Hoạt độngADM211EAR Tóm tắt
An RS-232 transceiver is an interface integrated circuit that combines line drivers and receivers with the electrical conversion required for balanced-looking differential signaling over single-ended, bipolar RS-232 connections. The ADM2xxE family is positioned as a robust RS-232 and V.28 interface solution, with onboard charge-pump support and external 0.1 uF capacitors used for the RS-232 interface voltage generation.
The ADM211EAR provides four RS-232 drivers and five receivers, allowing multiple channels and a full-duplex communications arrangement in one package. The manufacturer describes the ADM211 as a production part with a 200 kbps data rate, while the related ADM211E family is described as supporting rates up to 230 kbps. The device also provides shutdown and enable control functions in relevant family members, making it useful for systems that need controlled power states or interface isolation.
Key application areas include industrial data acquisition, test and measurement equipment, POS terminals, industrial controls, and embedded systems communicating with legacy RS-232 peripherals. The +5 V supply requirement simplifies system design where the logic supply is already present and a separate ±12 V RS-232 supply is not practical. External charge-pump capacitors should be placed close to the relevant pins, and the receiver inputs should be protected from electrostatic discharge and excessive voltage excursions.
When selecting this device, verify the exact driver and receiver count, enable and shutdown behavior, package suffix, and operating-temperature requirements against the Analog Devices ADM211 datasheet Rev. D. The 28-SOIC package is intended for conventional PCB assembly and offers a larger pin count than compact RS-232 interface packages. The ADM211EAR is therefore appropriate when a design needs several RS-232 channels from one +5 V supply and a standard SOIC footprint.
Bộ thay thế dễ dàng lắp đặt cho ADM211EAR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ADM211EARSZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM213EARSZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM211EAR Thông số kỹ thuật
| Product Type | RS-232 and V.28 interface transceiver |
| Điện áp cung cấp | +5 V |
| Driver Count | 4 |
| Receiver Count | 5 |
| ADM211 Data Rate | 200 kbps |
| ADM211E Family Data Rate | Up to 230 kbps |
| Charge Pump Capacitor | 0.1 uF |
| Receiver Input Levels | Up to 30 V |
| RS-232 Output Swing | 9 V |
| Hộp | 28-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Communication Standard | EIA-232-E and CCITT V.28 |
| ESD Protection | +/-15 kV |
| Power | 15 mW |
| Supplier Part Number | ADM211EAR |
Hướng dẫn cấu hình chân ADM211EAR 28-pin soic
Cấu hình chân cho ADM211EAR (28-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM211EAR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM211EAR phù hợp cho 6 Áp dụngs: Industrial Data Acquisition, Point-of-Sale Terminal Interface, Test and Measurement Equipment, Embedded Controller Communications, Industrial Control Panel, Service and Diagnostic Port.
Industrial Data Acquisition
The ADM211EAR is suitable for industrial measurement systems that must collect data from several RS-232 instruments while operating from a single +5 V rail. Its four drivers and five receivers allow multiple instrument or peripheral lines to be consolidated into one interface IC. The ADM211 family’s 200 kbps rate is appropriate for supervisory, configuration, and legacy instrumentation traffic rather than high-bandwidth streaming. Place the 0.1 uF charge-pump capacitors near their pins, route driver outputs to the connector through the recommended protection network, and keep receiver traces away from switching nodes to avoid coupling noise into low-level inputs.
Được đề xuất
Point-of-Sale Terminal Interface
The ADM211EAR can support point-of-sale and retail peripherals that retain an RS-232 service or peripheral interface. The 4/5 channel arrangement is useful when a terminal communicates with more than one serial device while the rest of the controller runs from +5 V logic. The interface’s 200 kbps capability comfortably handles transaction traffic, configuration exchanges, and status reporting. Keep the external charge-pump network compact, provide a stable +5 V source, and confirm the connector’s RS-232 voltage levels and ESD exposure before deploying the board in a retail environment.
Được đề xuất
Test and Measurement Equipment
The ADM211EAR fits laboratory and field-test equipment that must communicate with older RS-232 instruments, printers, or calibration devices. Multiple drivers and receivers can reduce the number of separate interface components, while the single +5 V operating requirement simplifies portable and benchtop instrument power systems. The interface is most appropriate for control and measurement traffic within the ADM211 family’s 200 kbps capability. Use short, properly terminated charge-pump connections, isolate connector grounds where appropriate, and validate receiver thresholds against the attached equipment before production testing.
Được đề xuất
Embedded Controller Communications
The ADM211EAR provides a practical RS-232 bridge for embedded controllers that must retain compatibility with service ports, programming fixtures, or legacy peripherals. Because the device runs from +5 V, it can share the controller’s logic supply without requiring a separate RS-232 voltage source. The five receivers and four drivers offer flexible channel allocation for command and response paths. Designers should verify the controller’s UART logic levels, provide the manufacturer-specified charge-pump capacitors, and keep the RS-232 driver outputs physically separated from sensitive receiver and clock traces.
Được đề xuất
Industrial Control Panel
The ADM211EAR is appropriate for control panels that interface with RS-232 programmable controllers, displays, or service adapters from a +5 V control board. Its channel count supports several communication endpoints without requiring one transceiver per port. The single-supply architecture is particularly useful in compact control electronics where space and rail count are constrained. Maintain the specified 0.1 uF charge-pump capacitor placement, provide local supply bypassing, and use an appropriate protection scheme on externally accessible connector pins to improve system reliability under industrial ESD and noise conditions.
Được đề xuất
Service and Diagnostic Port
The ADM211EAR can serve as a service-port interface for diagnostics, firmware loading, and configuration access in equipment that retains legacy RS-232 connectivity. The four-driver configuration permits multiple management lines, while the receiver channels support incoming status and command signals. A single +5 V supply reduces the complexity of service-port circuitry in embedded products. Design the connector entry with suitable ESD protection, maintain controlled return paths for RS-232 signals, and avoid treating the on-board transceiver as a complete substitute for a dedicated surge-protection network.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM211EAR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM211EARSZ | ADM213EARSZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Product Type | RS-232 and V.28 transceiver | RS-232 and V.28 transceiver | RS-232 transceiver |
| Supply Voltage | +5 V | +5 V | +5 V |
| Driver Count | 4 | 4 | 4 |
| Receiver Count | 5 | 5 | 5 |
Bảo phân biệt quan trọng
- Identical core device configuration (vsADM211EARSZ)
- Direct ordering-form interchange (vsADM211EARSZ)
- Related family option with receiver-behavior qualification required (vsADM213EARSZ)
Ghi chú thiết kế
Place the ADM211 family’s specified 0.1 uF charge-pump capacitors close to the associated device pins and follow the manufacturer’s polarity markings. Keep the high-current charge-pump loop compact, provide local supply decoupling at the +5 V pins, and avoid routing sensitive receiver inputs beneath or immediately beside the charge-pump nodes. This layout approach limits switching ripple and reduces the chance that the transceiver’s own generated noise will degrade adjacent low-level measurements.
Do not treat the ADM211EAR as a 5 V logic-level RS-232 driver. The transmitter side must produce the bipolar signal levels defined by RS-232, while the receiver side is designed for the wider voltage range associated with the interface. Verify the complete connector-side circuit, grounding arrangement, and external protection devices rather than assuming that the +5 V supply can connect directly to an RS-232 connector.
The ADM211 family contains a charge-pump converter, so PCB layout and connector cable arrangements can influence radiated emissions. Keep the charge-pump capacitor loop small, maintain a low-impedance return path for supply current, and avoid extending unprotected RS-232 traces unnecessarily across the board. At an externally accessible connector, use the protection approach specified by the manufacturer and validate the finished product with the system’s applicable EMC procedure.
Thông tin tuân thủ
The ADM211EAR documentation identifies EIA-232-E and V.28 interface compliance and ±15 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not confirmed.
