ADM236LJN - 4/3 5V RS-232 Transceiver | Analog Devices
MPN: ADM236LJN ✗ Cuối đờiADM236LJN Tóm tắt
A CMOS RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible voltage levels and converts received RS-232 signals back into logic levels. In the interface hierarchy, it belongs to the RS-232 transceiver category, then to communications interface ICs, then to broader interface and semiconductor families. It is useful wherever two systems must exchange serial data across a noise-prone, unbalanced cable using the EIA-232-E and V.28 signaling specifications.
Key features include a single 5 V power supply, four drivers, three receivers, a maximum data rate of 120 kB/s, an approximately 9 V output swing, and receiver input levels extending to 30 V. Low-power shutdown is supported, and the receivers remain active in shutdown according to the supplied family data. The interface also offers ESD protection greater than 2 kV and is described as latch-up free.
The ADM236L family uses onboard charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers from a single positive supply. This architecture removes the external ±12 V requirement common to older RS-232 implementations. A 4-to-3 driver and receiver arrangement suits asymmetric links, including systems that transmit on several lines but receive data on a smaller number of channels.
Typical uses include industrial control links, point-of-sale equipment, instrumentation, data acquisition, and embedded serial ports where a 5 V system cannot provide ±12 V. The 120 kB/s capability is suitable for moderate-speed control and data-transfer channels rather than high-bandwidth protocols. Its DIP-24 package is also appropriate for through-hole legacy and industrial boards.
Designers should provide the datasheet-specified 1 uF capacitors, route the charge-pump and interface connections according to the manufacturer's application guidance, and keep RS-232 routing away from sensitive analog signals. Confirm supply tolerance, transceiver direction, and connector-level protection against the actual board requirements before production use.
This page combines verified manufacturer-family specifications, distributor availability information, structured comparison data, and practical integration guidance. It distinguishes package-level replacement constraints from merely similar RS-232 devices, helping engineers avoid substitutions that require pinout, channel-count, or board-layout changes.
Bộ thay thế dễ dàng lắp đặt cho ADM236LJN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM236LJN (cùng hình factor và footprint) — khác nhau ở Number of Drivers, Number of Receivers, Package, Product Type, RS-232 Output Swing.
ADM238LJN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM237LJN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADM239LJN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADM241LJN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADM231LJN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADM236LJN Thông số kỹ thuật
| Product Type | RS-232 driver/receiver transceiver IC |
| Number of Drivers | 4 drivers |
| Number of Receivers | 3 receivers |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | Approximately 9 V with 5 V supply |
| Onboard Charge-Pump Capacitors | 1 uF |
| DC-DC Converter | Onboard |
| Shutdown Function | Low-power shutdown |
| Receiver Operation During Shutdown | Receivers active in shutdown |
| Receiver Input Voltage | 30 V |
| RS-232 Standards | EIA-232-E and V.28 |
| ESD Protection | Greater than 2 kV |
| Latch-Up | Latch-up free |
| Nhiệt độ hoạt động | 0 C to 70 C |
| Hộp | 24-pin DIP, 7.62 mm row spacing |
| Kiểu lắp đặt | Through-hole |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân ADM236LJN 24-pin dip, 7.62 mm row spacing
Cấu hình chân cho ADM236LJN (24-pin dip, 7.62 mm row spacing gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM236LJN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM236LJN phù hợp cho 6 Áp dụngs: Industrial Control Serial Interface, Point-of-Sale Terminal Connectivity, Data Acquisition and Instrumentation, Embedded Serial Port Expansion, Security and Access-Control Equipment, Service and Diagnostic Console.
Industrial Control Serial Interface
The ADM236LJN fits legacy industrial controllers that communicate over a point-to-point RS-232 link using only a regulated 5 V rail. Its four drivers and three receivers support several command, status, or interlock signals without requiring external ±12 V power. The maximum 120 kB/s rate is suitable for supervisory control data, while the approximately 9 V output swing and EIA-232-E and V.28 support provide an RS-232-compatible electrical interface. Designers should confirm the 0 C to 70 C operating range and verify channel direction against the controller schematic.
Được đề xuất
Point-of-Sale Terminal Connectivity
Point-of-sale peripherals often use RS-232 for receipt printers, customer displays, or service connectors even when the host electronics provide only 5 V. The ADM236LJN can drive four lines and receive three, making it useful for compact multi-function peripheral interfaces. Its 120 kB/s maximum data rate is more than adequate for typical configuration and transaction commands, while the onboard DC-DC converter and 1 uF capacitors simplify implementation around the transceiver. The design must still include suitable connector protection and verify the host's RS-232 logic direction.
Được đề xuất
Data Acquisition and Instrumentation
The ADM236LJN can bridge laboratory or industrial instrumentation that retains an RS-232 command port but lacks a bipolar supply. Multiple driver channels are useful for sending range, mode, trigger, and reset commands to separate instrument functions, while three receiver channels can return status or measurement acknowledgments. Operation from 4.5 V to 5.5 V simplifies integration with regulated test equipment, and 120 kB/s is adequate for short control packets. Engineers should observe the 0 C to 70 C range and validate the full instrument handshake before replacing legacy communications hardware.
Được đề xuất
Embedded Serial Port Expansion
An embedded controller with too few UART channels can use the ADM236LJN to expand a legacy serial interface, provided the target system supports the RS-232 electrical layer. Four driver outputs and three receiver inputs allow multiple control lines to coexist on one interface, and the 5 V supply requirement fits many embedded systems. The 120 kB/s ceiling makes the device appropriate for command and status traffic rather than bulk data transfer. Because the ADM236LJN is a transceiver rather than a protocol converter, firmware must independently handle framing, parity, and device addressing.
Được đề xuất
Security and Access-Control Equipment
ADM236LJN can support legacy access-control panels that distribute door commands, reader enables, alarms, and status returns over an RS-232 wiring run. Its four-driver, three-receiver arrangement suits asymmetric command-and-response systems, and the single 5 V supply reduces the power-conversion burden inside compact controller enclosures. The 120 kB/s data rate is adequate for identification and administrative records, while the 30 V receiver input rating adds tolerance for legacy signal conditions. Installation must verify surge, ground-loop, and connector requirements beyond the device's stated ESD protection.
Được đề xuất
Service and Diagnostic Console
The ADM236LJN is suitable for service consoles and diagnostic interfaces used to configure or inspect installed equipment over RS-232. Four outputs can initiate separate operations, while three inputs can return ready, fault, and acknowledgment signals. Its 5 V-only architecture simplifies portable or rack-mounted console electronics, and the 120 kB/s rate supports setup commands and diagnostic logs. The 0 C to 70 C operating range is appropriate for many indoor environments. Before deployment, confirm connector wiring, remote ground requirements, and whether the attached legacy equipment expects the ADM236LJN's 4/3 channel organization.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM236LJN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM238LJN | ADM237LJN | ADM239LJN | ADM241LJN | ADM231LJN |
|---|---|---|---|---|---|---|
| Package | DIP-24 | DIP-24 - same package | DIP-24 | DIP-24 | DIP-24 | DIP-24 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
Bảo phân biệt quan trọng
- Broader transmit and receive channel organization (vsADM238LJN)
- Single-supply RS-232 operation (vsADM238LJN)
- Full-size through-hole package (vsSP232ECT-L)
Ghi chú thiết kế
Place the datasheet-specified 1 uF charge-pump capacitors close to their associated ADM236LJN pins and use short, direct traces. Keep the RS-232 driver and receiver routes away from clocks, sensor inputs, and other sensitive analog nets. If the legacy system separates logic ground and RS-232 ground, define the connection intentionally at the interface reference point rather than allowing uncontrolled return current through the transceiver ground.
The ADM236LJN operates from a single 4.5 V to 5.5 V supply, so the board must provide a stable 5 V rail rather than relying directly on unregulated 5 V logic. Confirm supply tolerance, startup behavior, and the state of the shutdown pin before enabling external RS-232 equipment. The supplied data does not include quiescent-current values, so do not estimate power consumption without consulting the manufacturer datasheet.
Do not select a substitute based only on DIP-24 packaging. ADM238LJN is verified in the same package but has 2 drivers and 2 receivers rather than 4 drivers and 3 receivers. Confirm every channel direction, enable connection, charge-pump capacitor location, and shutdown function against the original schematic before substituting any ADM23x-family device.
RS-232 driver outputs are high-voltage, fast-edge signals and should not run parallel with sensitive analog inputs over long board distances. Use a solid ground reference, minimize stub branches, and keep external cables away from clock and reference lines. The verified family data cites ESD protection greater than 2 kV, but that rating does not replace connector surge protection or a properly designed chassis and ground system.
Thông tin tuân thủ
RoHS compliance is taken from the supplied comparison data. The manufacturer family datasheet states that the devices are latch-up free. No verified REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 information was supplied.
