ATF16V8C-5XC - 5ns 16V8 Flash PLD | Microchip
MPN: ATF16V8C-5XC ✗ Cuối đờiATF16V8C-5XC Tóm tắt
A programmable logic device, or PLD, is a semiconductor whose internal digital logic connections can be configured after manufacture. The ATF16V8C belongs to the simple PLD hierarchy: PLD → simple PLD → electrically erasable PLD → EECMOS Flash PLD. Unlike a mask-programmed PAL or a one-time-programmable fuse device, its Flash configuration can be erased and reprogrammed, simplifying logic updates, prototype corrections, and board rework.
The principal features include eight macrocells, eight outputs, eight inputs, a 5 ns maximum pin-to-pin delay, and operation across the 5 V supply range specified by the manufacturer datasheet. The architecture is a superset of generic 16R8 devices and can emulate many 20-pin combinatorial PLDs. Each output is allocated eight product terms, while automatically selected operating modes support registered, combinatorial, and more complex logic functions.
The ATF16V8C-5XC uses Atmel's proven electrically erasable Flash memory technology rather than ultraviolet-erasable EPROM. Flash programming supports reusable development cycles, while the low-cost software flow helps simplify device programming. A pin-controlled power-down mode can reduce current when the logic does not need to remain active, although exact current and operating-mode limits must be confirmed in the manufacturer datasheet.
Typical uses include industrial control logic, decoding and multiplexing, glue logic, interface conditioning, and other fixed digital functions requiring up to eight outputs and a 5 ns performance class. Its 20-pin TSSOP package is appropriate for compact surface-mount assemblies, but designers should verify land pattern, pin assignment, and signal timing against the official datasheet before layout release.
The primary design consideration is that device configuration, setup times, output feedback, OE handling, and power-down behavior must be treated as part of the timing design. The datasheet should be checked for the exact operating mode selected by the programming file, especially when registered outputs or feedback paths are used. PCB design should also provide a stable supply and clean routing for high-speed digital edges.
This page consolidates verified manufacturer and distributor information, practical programming and layout guidance, and a parameter comparison of same-package ATF16V8C speed alternatives. It also distinguishes verified facts from fields that require confirmation from the complete datasheet, preventing unverified timing, pinout, and pricing assumptions from being presented as engineering data.
Bộ thay thế dễ dàng lắp đặt cho ATF16V8C-5XC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATF16V8C-5XC (cùng hình factor và footprint) — khác nhau ở Architecture, Package.
ATF16V8C-7XC
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATF16V8C-10XC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATF16V8C-15XC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATF16V8C-20XC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATF16V8C-25XC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATF16V8C-5XC Tỷ lệ tối đa & tính chất điện
| Product Type | 16V8 Programmable Logic Device (PLD) |
| Programmable Technology | EE Flash PLD using EECMOS technology |
| Number of Macrocells | 8 macrocells |
| Số lượng đầu ra | 8 outputs |
| Maximum Pin-to-Pin Delay | 5 ns |
| Điện áp cung cấp | 5 V |
| Industrial Supply Voltage Range | 5 V ±10% |
| Commercial Supply Voltage Range | 5 V ±5% |
| Architecture | Superset of generic 16R8 architecture |
| Product Terms per Output | 8 product terms |
| Operating Modes | Registered, combinatorial, and complex logic modes |
| Power-Down Mode | Pin-controlled; 100 µA option stated for the device family |
| Hộp | 20-TSSOP (0.173 inch, 4.40 mm width) |
| Kiểu lắp đặt | Surface mount |
| Packaging | Tube |
| Lead-Free Status | Contains lead |
Hướng dẫn cấu hình chân ATF16V8C-5XC 20-tssop (0.173 inch, 4.40 mm width)
Cấu hình chân cho ATF16V8C-5XC (20-tssop (0.173 inch, 4.40 mm width) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATF16V8C-5XC.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATF16V8C-5XC phù hợp cho 6 Áp dụngs: Industrial Control and Automation Logic, Legacy Interface and Bus Decoding, Product Test and System Diagnostics, Embedded Peripheral Control, Instrumentation Signal Conditioning, Communication Equipment Support Logic.
Industrial Control and Automation Logic
The ATF16V8C-5XC is suitable for compact control logic where a 16V8 architecture and 5 ns maximum pin-to-pin delay are needed. Its eight macrocells, eight outputs, and eight product terms per output can implement decoding, state-transition, interlocking, and output-selection functions that would otherwise consume multiple conventional gates. The device’s 20-TSSOP package also supports compact surface-mount control boards. Because this ordering code is marked obsolete, it is most appropriate for maintenance, replication, and legacy-system support. New production designs should confirm availability and verify all timing against the manufacturer datasheet.
Được đề xuất
Legacy Interface and Bus Decoding
The ATF16V8C-5XC can implement address decoding, chip-select generation, data routing, and command qualification in legacy digital interfaces. Its 5 ns speed grade provides more timing margin than slower PLD options when combinational outputs participate in multi-level decision paths, while the electrically erasable Flash configuration allows a design to be revised without replacing the entire device. Each of the eight outputs can use eight product terms, providing enough logic depth for many address and control functions. Engineers should still validate output feedback, OE timing, and operating-mode behavior against the complete pinout and timing tables.
Được đề xuất
Product Test and System Diagnostics
The ATF16V8C-5XC is applicable to compact board test, fixture-control, and diagnostic logic where discrete gate counts would increase board area. Eight macrocells can consolidate stimulus selection, pass/fail decisions, and control-output generation into one reprogrammable device. Its 5 ns maximum pin-to-pin delay helps preserve margin in short combinational test paths, and Flash technology permits configuration updates as test requirements evolve. Because the exact part is obsolete, engineers should verify programmer availability, supply continuity, and any required safety or quality documentation before using it in new production test equipment.
Được đề xuất
Embedded Peripheral Control
The ATF16V8C-5XC can serve as dedicated glue logic between a microcontroller, memory, and peripheral devices. Eight configurable outputs and flexible registered or combinatorial modes support chip enables, arbitration, interrupt qualification, reset sequencing, and data-format adaptation. A 5 ns maximum propagation delay is useful when control signals must be resolved within short system timing windows. The 20-TSSOP package reduces board area compared with larger through-hole PAL devices, although an obsolete ordering code should be reserved for legacy platforms or approved repair applications rather than new embedded platforms with long-term sourcing requirements.
Được đề xuất
Instrumentation Signal Conditioning
The ATF16V8C-5XC can implement front-panel sequencing, range selection, status encoding, and control interlocks in electronic test and measurement equipment. The 16V8 architecture provides a compact way to realize multiple related Boolean functions while keeping the design programmable for later revisions. Its 5 ns pin-to-pin speed class can improve response in short control chains, and the TSSOP package supports panel and instrument PCB density. Timing closure must account for the selected registered or combinatorial mode, clock distribution, output enable behavior, and supply tolerance; those details are not fully available in the supplied search excerpts.
Được đề xuất
Communication Equipment Support Logic
The ATF16V8C-5XC is suitable for line-interface support functions such as channel selection, timing qualification, frame decoding, and alarm generation. The eight macrocells and selectable operating modes allow relatively complex combinational and registered functions to be consolidated into one 20-TSSOP device. Its 5 ns maximum propagation delay provides useful margin for short local control paths, while Flash configuration simplifies reuse of the same board across several related protocols. Because this exact MPN is obsolete and no complete pin table was provided, production use requires confirmation of supply, pin compatibility, setup and hold timing, and programming-tool support.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATF16V8C-5XC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATF16V8C-7XC | ATF16V8C-10XC | ATF16V8C-15XC | ATF16V8C-20XC | ATF16V8C-25XC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP |
| Maximum Pin-to-Pin Delay | 5 ns | 7 ns | 10 ns | 15 ns | 20 ns | 25 ns |
| Product Family | ATF16V8C | ATF16V8C | ATF16V8C | ATF16V8C | ATF16V8C | ATF16V8C |
| Number of Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Programmable Technology | EE Flash PLD using EECMOS technology | EE Flash PLD using EECMOS technology | EE Flash PLD using EECMOS technology | EE Flash PLD using EECMOS technology | EE Flash PLD using EECMOS technology | EE Flash PLD using EECMOS technology |
| Number of Outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs |
| Supply Voltage | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal |
Bảo phân biệt quan trọng
- Faster same-family timing class (vsATF16V8C-25XC)
- Shorter timing margin for critical local control paths (vsATF16V8C-10XC)
- Reusable Flash configuration within the same architecture (vsATF16LV8C-10XC)
- Compact 20-TSSOP implementation with eight outputs (vsATF16V8C-15XC)
Ghi chú thiết kế
Do not treat every ATF16V8C suffix as interchangeable without checking the package, speed grade, and temperature grade. The verified target uses the “-5XC” ordering code and a 20-TSSOP package. Before substituting another family member, compare the manufacturer pin configuration, programmed architecture, supply range, setup and hold timing, output behavior, and package drawing. A shared 16V8 family name does not by itself prove that two programmed devices are drop-in replacements.
The ATF16V8C-5XC is a 5 ns maximum pin-to-pin device, so clock, feedback, and output-enable paths require disciplined routing. Keep critical traces short, avoid unnecessary stubs, provide a continuous ground reference, and route the clock away from switching outputs where practical. Place any required bypass capacitance close to the supply and ground pins according to the official layout guidance. Validate setup and hold timing with actual board and load assumptions rather than relying only on the 5 ns headline specification.
Use the 5 V nominal operating range specified for the applicable temperature grade and verify the exact limits for the “XC” suffix in the manufacturer datasheet. Power-down can reduce supply current when the logic is idle, but the OE and PD pins must be sequenced without violating the device’s input-voltage and timing requirements. Since the exact part is obsolete, also confirm whether an authorized distributor can provide traceable production quantities rather than relying on spot-market inventory.
Use the official 20-TSSOP land pattern and confirm its pin-1 orientation against the package drawing before PCB release. The supplied excerpts verify the TSSOP-20 package but do not provide the numbered signal table, so no unverified pin mapping should be used. Check solder-reflow profile, tube-to-board handling, and exposed lead clearances during mechanical review. For legacy repairs, inspect the original assembly for paste residue or hand soldering before fitting the replacement.
Thông tin tuân thủ
The verified distributor specification states that the ATF16V8C-5XC contains lead. RoHS, REACH, halogen-free, and conflict-minerals declarations were not included in the supplied data and are therefore recorded as unknown. AEC-Q100 is not applicable because this is a programmable logic device rather than an automotive-qualified semiconductor product.
