ATMEGA48PB-AUR - 8-bit AVR MCU 20MHz 4KB Flash TQFP-32 | Microchip
MPN: ATMEGA48PB-AUR ✓ Hoạt độngATMEGA48PB-AUR Tóm tắt
An 8-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory, data memory, and peripherals on one die. Within the power-management and embedded-systems hierarchy, the ATmega48PB sits in the entry tier of the AVR ATmega family, below the ATmega88PB and ATmega168PB, and executes one instruction per clock cycle for throughput approaching 1 MIPS/MHz.
Key features include 27 general-purpose I/O lines, 256 B EEPROM with read-while-write Flash capability, three flexible timer/counters with compare modes, internal and external interrupt sources, and a USART with wake-up on start of transmission. The picoPower technology enables very low sleep-mode consumption, supporting battery-powered designs.
The AVR enhanced RISC architecture uses 32 general-purpose working registers directly connected to the ALU, allowing powerful single-cycle instructions. The core-independent peripherals (event system, timers, USART) offload tasks from the CPU, reducing active time and overall energy per operation. Supply voltage spans 1.8 V to 5.5 V, covering 3.3 V and 5 V systems.
Typical applications include industrial sensor nodes, consumer appliance control, battery-powered IoT devices, and low-cost motor or LED control boards where a 5 V tolerant, low-power 8-bit controller is preferred.
A key design consideration: per Microchip application note 00002603A, the ATmega48PB can be a drop-in replacement for the ATmega48PA/ATmega48A in the 32-pin TQFP only if Pin 3 (GND-connected, must not be actively driven or ACO enabled) and Pin 6 (VCC-connected, must not be actively driven) meet stated conditions.
This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical migration design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho ATMEGA48PB-AUR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATMEGA48PB-AUR (cùng hình factor và footprint) — khác nhau ở RoHS Status, Communication Interfaces, Package, Timer/Counters, Program Memory Size.
ATMEGA48PA-AUR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATMEGA48PA-AU
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATMEGA48A-AUR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATMEGA88PB-AUR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATMEGA168PB-AUR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATMEGA328PB-AUR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATMEGA48-20AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATMEGA48PB-AUR Tỷ lệ tối đa & tính chất điện
| Core Processor | AVR |
| Core Size | 8-bit |
| Speed | 20 MHz |
| Flash Memory | 4 KB (2K x 16) |
| EEPROM | 256 B |
| SRAM | 512 B |
| General-Purpose I/O | 27 |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Timers/Counters | 3 flexible timer/counters with compare modes |
| Communication Interfaces | USART with wake-up on start of transmission |
| Working Registers | 32 general-purpose registers |
| Performance | Up to 1 MIPS/MHz (single-cycle RISC) |
| Low-Power Technology | picoPower |
| Hộp | 32-TQFP (7x7 mm) |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tape & Reel (AUR suffix) |
| Functional Safety | FuSa capable (per DigiKey listing) |
| Trạng thái RoHS | Compliant (GRN / green package per Mouser) |
Cấu hình chân ATMEGA48PB-AUR
| Chân 1 | PD3 — Port D, bit 3 (GPIO / INT1) |
| Chân 2 | PD4 — Port D, bit 4 (GPIO / XCK/T0) |
| Chân 3 | GND — Ground (PB device caution: if connected to GND, must not be actively driven or ACO enabled) |
| Chân 4 | VCC — Digital supply voltage (1.8 V to 5.5 V) |
| Chân 5 | GND — Ground |
| Chân 6 | VCC — Digital supply voltage (PB device caution: if connected to VCC, must not be actively driven) |
| Chân 7 | PB6 — Port B, bit 6 (XTAL1 / TOSC1) |
| Chân 8 | PB7 — Port B, bit 7 (XTAL2 / TOSC2) |
| Chân 9 | PD5 — Port D, bit 5 (GPIO / T1 / OC0B) |
| Chân 10 | PD6 — Port D, bit 6 (GPIO / AIN0 / OC0A) |
| Chân 11 | PD7 — Port D, bit 7 (GPIO / AIN1) |
| Chân 12 | PB0 — Port B, bit 0 (GPIO / ICP1 / OC1A) |
| Chân 13 | PB1 — Port B, bit 1 (GPIO / OC1A) |
| Chân 14 | PB2 — Port B, bit 2 (GPIO / SS / OC1B) |
| Chân 15 | PB3 — Port B, bit 3 (GPIO / MOSI / OC2A) |
| Chân 16 | PB4 — Port B, bit 4 (GPIO / MISO) |
| Chân 17 | PB5 — Port B, bit 5 (GPIO / SCK) |
| Chân 18 | AVCC — Analog supply voltage for ADC |
| Chân 19 | ADC6 — Analog input channel 6 |
| Chân 20 | AREF — Analog reference voltage for ADC |
| Chân 21 | GND — Ground |
| Chân 22 | ADC7 — Analog input channel 7 |
| Chân 23 | PC0 — Port C, bit 0 (GPIO / ADC0) |
| Chân 24 | PC1 — Port C, bit 1 (GPIO / ADC1) |
| Chân 25 | PC2 — Port C, bit 2 (GPIO / ADC2) |
| Chân 26 | PC3 — Port C, bit 3 (GPIO / ADC3) |
| Chân 27 | PC4 — Port C, bit 4 (GPIO / ADC4 / SDA) |
| Chân 28 | PC5 — Port C, bit 5 (GPIO / ADC5 / SCL) |
| Chân 29 | PC6 — Port C, bit 6 (RESET, active low) |
| Chân 30 | PD0 — Port D, bit 0 (GPIO / RXD) |
| Chân 31 | PD1 — Port D, bit 1 (GPIO / TXD) |
| Chân 32 | PD2 — Port D, bit 2 (GPIO / INT0) |
Ứng dụng tiêu biểu
ATMEGA48PB-AUR phù hợp cho 6 Áp dụngs: Industrial Sensor Nodes, Battery-Powered Consumer Devices, Motor Control and LED Drivers, Home Automation and IoT End Nodes, Appliance and White-Goods Control, Data Acquisition and Test Fixtures.
Industrial Sensor Nodes
The ATMEGA48PB-AUR fits industrial sensor nodes because its 27 GPIO lines and multi-channel ADC port pins (ports B, C, and D) connect directly to analog sensors, while the USART transmits readings over RS-485 or UART links. The picoPower technology keeps sleep currents minimal between sampling intervals, extending battery life in battery-backed nodes, and the 1.8 V to 5.5 V supply range tolerates noisy 5 V industrial rails without a regulator change. Placing the MCU in power-down mode between 1 Hz samples with a watchdog wake-up can reduce average consumption by orders of magnitude versus continuous polling, at the cost of slightly slower event response.
Được đề xuất
Battery-Powered Consumer Devices
For battery-powered consumer products such as remote controls, small meters, and personal care devices, the ATMEGA48PB-AUR's picoPower technology delivers very low sleep-mode consumption, directly extending battery life where standby time dominates. The 4 KB Flash is sufficient for button handling, LED or LCD driving, and simple protocols, keeping BOM cost near $0.54 per unit (as of 2026-09-18). Its 1.8 V operation supports direct use of two alkaline cells or a single Li-cell via an LDO. The trade-off is limited code headroom: once firmware approaches 4 KB, migration to the pin-compatible ATMEGA88PB-AUR preserves the same PCB footprint.
Được đề xuất
Motor Control and LED Drivers
The ATMEGA48PB-AUR suits small motor and LED control boards because its three flexible timer/counters with compare modes generate PWM outputs for H-bridge or MOSFET drivers, and core-independent peripherals continue running while the CPU sleeps or handles communication. Twenty MHz operation allows 8-bit PWM at roughly 78 kHz (20 MHz / 256), inaudible for fan and LED dimming applications. The 27 GPIO lines cover direction, enable, and feedback signals for single-motor designs. For higher current, pair it with a gate driver rather than driving MOSFETs directly, since GPIO current is limited to datasheet port ratings.
Được đề xuất
Home Automation and IoT End Nodes
In home automation end nodes, the ATMEGA48PB-AUR handles switch inputs, relay or triac control, and serial links to wireless modules through its USART with wake-up on start of transmission, which lets the MCU sleep until the radio asserts data. PicoPower sleep modes keep average draw compatible with coin-cell or rechargeable supply budgets, and internal interrupts allow wake-up on button press without polling. The 4 KB Flash accommodates a light protocol stack; heavier Zigbee/BLE stacks require the pin-compatible ATMEGA168PB-AUR or an external radio module with onboard intelligence.
Được đề xuất
Appliance and White-Goods Control
The ATMEGA48PB-AUR is cost-effective for appliance control panels where a 5 V tolerant 8-bit MCU drives keys, LEDs, and a buzzer while reading NTC thermistors through the ADC. Its three timers support beep tones and display multiplexing concurrently, and the 1.8 V to 5.5 V range plus green RoHS packaging (GRN per Mouser) simplifies compliance for mass-market goods. The TQFP-32 7x7 mm footprint suits both wave-reflowable and rework-friendly assembly. Firmware simplicity is the attraction here; products needing touch sensing or more I/O should step to larger ATmega variants rather than expanding the 48PB.
Được đề xuất
Data Acquisition and Test Fixtures
For low-cost data acquisition cards and production test fixtures, the ATMEGA48PB-AUR provides an ADC, USART for host communication, and timers for sample pacing at up to 20 MHz clock rates. The 32 general-purpose working registers make single-cycle register-to-register arithmetic efficient for simple filtering. Its TQFP-32 package and reprogrammable ISP Flash allow fixture firmware updates in the field. For applications requiring USB connectivity to the host PC, pair it with the ATMEGA32U2-MU acting as a USB-serial bridge, keeping the 48PB focused on measurement sequencing while the 32U2 handles the USB protocol.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATMEGA48PB-AUR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATMEGA48PA-AUR | ATMEGA88PB-AUR | ATMEGA168PB-AUR | ATMEGA328PB-AUR |
|---|---|---|---|---|---|
| Package | 32-TQFP (7x7 mm) | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Architecture | AVR 8-bit RISC, 1 MIPS/MHz | AVR 8-bit RISC, 1 MIPS/MHz | AVR 8-bit RISC, 1 MIPS/MHz | AVR 8-bit RISC, 1 MIPS/MHz | AVR 8-bit RISC, 1 MIPS/MHz |
| Max Clock Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 4 KB | 4 KB | 8 KB | 16 KB | 32 KB |
| SRAM | 512 B | 512 B | 1 KB | 1 KB | 2 KB |
| EEPROM | 256 B | 256 B | 512 B | 512 B | 1 KB |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| picoPower Technology | Yes | No (PA revision) | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- picoPower technology for ultra-low sleep current (vsATMEGA48PA-AUR)
- Lowest-cost entry to the drop-in PB memory ladder (vsATMEGA88PB-AUR)
- Functional Safety (FuSa) capable listing (vsATMEGA48-20AU)
Ghi chú thiết kế
When migrating from ATmega48PA/88PA/168PA to the ATmega48PB in the 32-pin TQFP, Microchip application note 00002603A imposes two conditions: Pin 3 - if connected to GND, the pin must not be actively driven and the analog comparator output ACO must not be enabled; Pin 6 - if connected to VCC, the pin must not be actively driven. Verify your existing schematic against these two pins before releasing the PB as a drop-in replacement. Ignoring these conditions can cause unpredictable analog comparator behavior in the field.
Place a 100 nF ceramic decoupling capacitor directly across VCC (pin 4) and GND (pin 3), and a second one across VCC (pin 6) and GND (pin 5), with short, wide traces to the ground plane. AVCC (pin 18) should be tied to VCC through an LC filter (for example 10 uH plus 100 nF) when the ADC is used, keeping the analog reference (pin 20, AREF) quiet with its own 100 nF capacitor. The exposed 7x7 mm TQFP-32 center of the board benefits from a solid ground pour for ADC noise reduction.
Estimated: at 20 MHz and 5 V, an ATmega-class core draws on the order of 10-15 mA active (verify against datasheet 40001909A electrical characteristics for the exact typical value). The dominant lever is sleep policy - using power-down mode with watchdog or pin-change wake-up between events can cut average current by two to three orders of magnitude in battery designs. Note that maximum clock frequency derates with supply voltage per the datasheet frequency-vs-voltage curve: 20 MHz requires operation near 5 V, while 3.3 V systems are limited to roughly 13-14 MHz.
For the USART (pins 30/31, RXD/TXD) and SPI ISP lines (PB3-PB5), keep serial traces short and avoid routing them beneath the crystal circuit at PB6/PB7. If using an external crystal above 8 MHz, keep crystal load capacitors close to the pins and place a guard ground ring around the crystal traces to prevent UART jitter from coupled noise. Enable the internal pull-ups on unused port pins or configure them as outputs low to avoid floating inputs increasing current consumption.
Thông tin tuân thủ
Mouser lists the part as 'TQFP GRN' - Microchip's green, RoHS-compliant, halogen-free package designation. REACH and conflict-minerals declarations should be downloaded from the Microchip product page compliance section.
